Regenerated cellulose ultrafiltration membranes in the treatment of pulp and paper mill process waters

Ultrafiltration (UF) is widely applied in different separation processes in the pulp and paper industry. The growing need to protect the environment, a lack of pure water and an interest in producing high-value chemicals from compounds present in process waters will probably lead to an increase in the use of UF in the pulp and paper industry. The efficiency and cost-effectiveness of a UF process depends on the applied membrane. The membrane should have a high and stable filtration capacity, a particular selectivity and a long operational lifetime. To meet these requirements a membrane should have a low fouling tendency. In addition, it should withstand the prevailing operational and chemical conditions. This thesis evaluates the performance and applicability of the regenerated cellulose (RC) membranes 00030T and C2 in the treatment of pulp and paper mill process waters based on the requirements above. The results demonstrated that both the tested RC membranes fulfilled well the requirement of high filtration capacity. In addition, in the filtration of a paper mill clear filtrate (CF) the RC membranes were not as greatly affected by variations in the CF quality as a polysulphone membrane. Furthermore, due to their extreme hydrophilicity and weak charge the fouling tendency of the membranes can be expected to be low in pulp and paper mill filtration applications. It is, however, known that fouling cannot be totally avoided even when the membrane is chosen very carefully. This study indicated that carbohydrates influenced negatively on permeability and caused fouling in the filtration of groundwood mill circulation water. Thus, a pre-treatment effectively reducing the amount of carbohydrates might help to maintain a stable capacity. However, the results of the thesis also showed that the removal of some of the possible foulants might just increase the harmful effect of others. Multivariate examination was useful in the understanding of the complicated factors causing the unstable capacity. The thesis also revealed that the 00030T and C2 membranes can be used at high pressure (max. tested pressure 12 bar). The C2 membrane, having a sponge-like substructure, was more pressure resistant, and its performance was more stable at high pressure compared to the UCO30T membrane containing macrovoids in its substructure. Both tested membranes can, according to the results, also be used at temperatures as high as 70°C in acidic, neutral and alkaline conditions. However, the use at extreme conditions might cause faster ageing of the membranes compared to ageing in neutral conditions. The thesis proved that both the tested RC membranes are very suitable for pulp and paper mill applications and that the membranes can be utilised in processes operating in challenging conditions. Thus, they could be used in more demanding applications than supposed earlier.

Facilitating coordination improvement efforts in cross-functional process development programs

Business process improvement is a common approach in increasing the effectiveness of an organization. It can be seen as an effort to increase coordination between units. Process improvement has proved to be challenging, and most management consultation firms facilitate organizations in this kind of initiatives. Cross-functional improvement is one of the main areas for internal consultants as well. However, the needs, challenges and means of cross-functional help have been rarely discussed in the literature. The objective of this thesis is on one hand to present a conceptual and descriptive framework to help understand the challenges of facilitating coordination improvement efforts in cross-functional improvement programs, and on the other hand to develop and test feasible solutions for some facilitation situations. The research questions are: 1. Why and in what kind of situations do organizations need help in developing coordination in cross-functional processes? 2. How can a facilitator help organizations in improving coordination to develop cross-functional processes? The study consists of two parts. The first part is an overview of the dissertation, and the second part comprises six research publications. The theoretical background for the study are the differentiation causing challenges in cross-functional settings, the coordination needed to improve processes, change management principles, methods and tools, and consultation practises. Three of the publications introduce tools for helping in developing prerequisites, planning responsibilities and supporting learning during the cross-functional program. The three other papers present frameworks to help understand and analyse the improvement situation. The main methodological approaches used in this study are design science research, action research and case research. The research data has been collected from ten cases representing different kinds of organizations, processes and developing situations. The data has been collected mainly by observation, semi-structured interviews and questionnaires. The research contributes to the rare literature combining coordination theories and process improvement practises. It also provides additional understanding of a holistic point of view in process improvement situations. The most important contribution is the addition to the theories of facilitating change in process improvement situations. From the managerial point of view, this study gives advice to managers and consultants in planning and executing cross-functional programs. The main factors increasing the need for facilitation are the challenges for differentiation, challenges of organizational change in general, and the novelty of initiatives and improvement practices concerning process development. Organizations need help in creating the prerequisites to change, in planning initiatives, easing conflict management and collaboration between groups, as well as supporting the learning of cross-functional improvement. The main challenges of facilitation are combining the different roles as a consultant, maintaining the ownership for the improvement project with the client, and supporting learning in the client organization.

Process intensification: From optimised flow patterns to microprocess technology

This thesis is focused on process intensification. Several significant problems and applications of this theme are covered. Process intensification is nowadays one of the most popular trends in chemical engineering and attempts have been made to develop a general, systematic methodology for intensification. This seems, however, to be very difficult, because intensified processes are often based on creativity and novel ideas. Monolith reactors and microreactors are successful examples of process intensification. They are usually multichannel devices in which a proper feed technique is important for creating even fluid distribution into the channels. Two different feed techniques were tested for monoliths. In the first technique a shower method was implemented by means of perforated plates. The second technique was a dispersion method using static mixers. Both techniques offered stable operation and uniform fluid distribution. The dispersion method enabled a wider operational range in terms of liquid superficial velocity. Using dispersion method, a volumetric gas-liquid mass transfer coefficient of 2 s-1 was reached. Flow patterns play a significant role in terms of the mixing performance of micromixers. Although the geometry of a T-mixer is simple, channel configurations and dimensions had a clear effect on mixing efficiency. The flow in the microchannel was laminar, but the formation of vortices promoted mixing in micro T-mixers. The generation of vortices was dependent on the channel dimensions, configurations and flow rate. Microreactors offer a high ratio of surface area to volume. Surface forces and interactions between fluids and surfaces are, therefore, often dominant factors. In certain cases, the interactions can be effectively utilised. Different wetting properties of solid materials (PTFE and stainless steel) were applied in the separation of immiscible liquid phases. A micro-scale plate coalescer with hydrophilic and hydrophobic surfaces was used for the continuous separation of organic and aqueous phases. Complete phase separation occurred in less than 20 seconds, whereas the separation time by settling exceeded 30 min. Fluid flows can be also intensified in suitable conditions. By adding certain additives into turbulent fluid flow, it was possible to reduce friction (drag) by 40 %. Drag reduction decreases frictional pressure drop in pipelines which leads to remarkable energy savings and decreases the size or number of pumping facilities required, e.g., in oil transport pipes. Process intensification enables operation often under more optimal conditions. The consequent cost savings from reduced use of raw materials and reduced waste lead to greater economic benefits in processing.

Development of tender information process by business intelligence in a global company unit

The purpose of this Thesis was to study what is the present situation of Business Intelligence of the company unit. This means how efficiently unit uses possibilities of modern information management systems. The aim was to resolve how operative informa-tion management of unit’s tender process could be improved by modern information technology applications. This makes it possible that tender processes could be faster and more efficiency. At the beginning it was essential to acquaint oneself with written literature of Business Intelligence. Based on Business Intelligence theory is was relatively easy but challenging to search and discern how tender business could be improved by methods of Busi-ness Intelligence. The empirical phase of this study was executed as qualitative research method. This phase includes theme and natural interviews on the company. Problems and challenges of tender process were clarified in a part an empirical phase. Group of challenges were founded when studying information management of company unit. Based on theory and interviews, group of improvements were listed which company could possible do in the future when developing its operative processes.

Offering planning process development: Bridging the Offering Gaps and Consolidating Top Priority Needs in Product Offering

The aim of this Thesis is to study how to manage the front-end of the offering planning process. This includes actual process development and methods to gather and analyze information to achieve the best outcome in customer oriented product offering. Study is carried out in two parts: theoretical part and company related part. Theoretical framework is created introducing different types of approaches to manage product planning processes. Products are seen as platforms and they are broken down to subsystems to show different parts of the development. With the help of the matrix-based approaches product platform related information is gathered and analyzed. In this kind of analysis business/market drivers and cus-tomer/competitor information are connected with product subsystems. This gives possibilities to study product gaps/needs and possible future ideas/scenarios in different customer segments. Company related part consists of offering planning process development in real company environment. Process formation includes documents and tools that guide planning from the information gathering to the prioritization and decision making.

Supplier Evaluation Using Analytical Hierarchy Process

The goal of the thesis is to make a supplier evaluation using analytical hierarchy process. Before the supplier evaluation is performed there will be introduced the principles of purchasing which gives a viewpoint to the supplier evaluation and management. The thesis will also give an overview on quality, performance and forecasts which are very important to the supplier evaluation and future improvements. The chapter which describes analytical hierarchy process will show the reader what exactly is analytical hierarchy process and how can it be utilized in supplier evaluation. In the later stages, thesis will provide information about the case company EADS Secure Networks Oy, the processes applied there towards purchasing and how the analytical hierarchy process is applied in practise. In the end of the thesis there will be an overview about each supplier’s strong and weak points as well as some comments and ideas about developing also EADS Secure Networks procedures to a direction which would benefit the whole customer–supplier–chain.

Integration of a Bioethanol Process to a Pulp Mill

Tässä diplomityössä tutkittiin puuhakkeen esihydrolyysi- ja hakkuujätteen hydrolyysiprosessien integroimista sellutehtaaseen bioetanolin tuottamiseksi. Tällaisesta ns. biojalostamosta luotiin WinGEMS-simulointiohjelmalla simulointimalli, jonka avulla tutkittiin bioetanoliprosessin vaikutusta sellutehtaan massa- ja energiataseisiin sekä alustavaa biojalostamon kannattavuutta. Simuloinnissa tarkasteltiin kolmea eri tapausta, joissa mäntysellun tuotannon ajateltiin olevan 1000 tonnia päivässä ja hakkuujätettä käytettävän 10 % tarvittavan kuitupuun määrästä: 1) Puuhakkeen esihydrolyysi ja hakkuujätteen hydrolyysi etanolin tuottamiseksi 2) Puuhakkeen esihydrolyysi, hakkuujäte kuorikattilaan poltettavaksi 3) Ei esihydrolyysiä, hakkuujäte kuorikattilaan poltettavaksi Verrattuna tapaukseen 3, puun kulutus kasvaa 16 % esihydrolysoitaessa puuhake ennen keittoa tapauksissa 1 ja 2. Kasvaneella puun kulutuksella tuotetaan tapauksessa 1 149 tonnia etanolia ja 240 MWh enemmän ylimääräsähköä päivässä. Tapauksessa 2 tuotetaan 68 tonnia etanolia ja 460 MWh enemmän ylimääräsähköä päivässä. Tämä tuottaisi vuotuista lisäkassavirtaa 18,8 miljoonaa euroa tapauksessa 1 ja 9,4 miljoonaa euroa tapauksessa 2. Hydrolyysin tuoteliuoksen, hydrolysaatin, haihduttaminen sekä hydrolyysiprosessien orgaanisten jäännöstuotteiden haihduttaminen ja polttaminen kasvattavat haihduttamon ja soodakattilan kuormitusta. Verrattuna tapaukseen 3, tapauksissa 1 ja 2 haihduttamon vaiheiden määrä on kasvatettava viidestä seitsemään ja tarvittavat lämmönsiirtopinta-alat lähes kaksinkertaistettava. Soodakattilan kuormitus kasvaa 39 % tapauksessa 1 ja 26 % tapauksessa 2.

Design Process of Packaging Laboratory at Lappeenranta University of Technology

The layout design process of the packaging laboratory at Lappeenranta University of Technology is documented in this thesis. Layout planning methods are discussed in general. The systematic layout planning procedure is presented in more detail as it is utilised in the case of layout planning of the packaging laboratory. General demands for research laboratory are discussed both from the machine and product perspectives. The possibilities for commercial food processing in the laboratory are discussed from the point of view of foodstuff processing regulations and hygiene demands. The layout planning process is documented and different layout possibilities are presented. Different layout drafts are evaluated and one layout draft is developed to be the final layout of the packaging laboratory. Guideline for technical planning and implementation based on the final layout is given

The Innovation Process – Aiming towards Innovativeness in a Construction Company

The bachelor’s thesis concentrates on the innovativeness in the construction industry. The purpose of the thesis is to define the innovation as a concept reflected on a context of the construction industry. The second objective is to examine how the construction companies could foster and increase the innovativeness. The third objective was to find out tools, methods and phases of the front-end of the innovation process. The construction industry is often considered as a traditional and an old-fashioned manufacturing industry. The innovation or the innovativeness rarely linked to the construction industry. Productivity is a common problem in the construction industry. The construction industry needs to increase the productivity to compete in a globalized world. The productivity can be increased by the innovation. The thesis based on a literature review. The findings from the literature include a description of the innovation as a concept, the innovative culture and the innovation process as a context of the construction industry. The phases of the front-end of the innovation process were explained. Customers centered approach was taken into account in the innovation process. The required tools and methods for managing the front-end of the innovation process were illustrated. The thesis ensures the importance of the innovation facing challenges of the construction industry. Managing the front-end of the innovation is the most important aspect to stand out from the less innovative companies. To take a full advantage of the innovation companies cannot fear of changes. The innovation process requires a full support of the top management of the company. Taking into consideration a theoretical aspect of the thesis a further research is required to respond practical needs of the company. Tools and methods should be considered according the company’s needs and activities. Company’s existing state and culture should be examined before implementing the front-end of the innovation process to ensure the functionality.

Characterization of Microparticle Retention Systems with Retention Process Analyzer

In the literature survey retention mechanisms, factors effecting retention and microparticles were studied. Also commercial microparticle retention systems and means to measure retention were studied. Optical retention measurement with RPA and Lasentec FBRM was studied. The experimental part contains study of different cationic polyacrylamides, anionic silica, bentonite and new generation micropolymer. In these studies the dosage, dosing order and dosing history were changing factors. The experimental work was done with RPA-apparatus with which, the retention process can be followed in real time. In testing was found that silica yielded better retention, when dosed nontraditionally before the polymer. Also silica was very dependant on the polymer dosage. With bentonite good colloidal retention was achieved with relatively low doses. Unlike silica bentonite was not dependant on polymer dosage. The relation of bentonite and polymer dosage is more defining when high retention is wanted. With 3-component systems using bentonite very high retention was achieved. With silica no improvement in retention was found in 3-component systems compared to dual component systems.

Creating and implementing a financial management process to an international company

The objectives of this thesis areto identify the best elements from Information Technology Infrastructure Library financial management for an international company. The elements need to be customized to fit existing elements and the thesis needs to provide implementation proposal. The new IT financial management needs to improve cost visibility and bring benefits to the company. In order to find the best elements for IT financial management, there needs to be a research to discover the companys business needs. The ITIL library is used to find answers and solutions to the companys issues in IT financial management. Other IT frameworks can and will be used as well, if they are able to work with ITIL model. ITIL consists from budgeting, accounting and charging in IT financial management, which all needs to be investigated. In addition more ITIL elements such as contract management and supplier management can be used, in order to make IT financial management work better.

Welding of Sheet metal using Modified short arc MIG/MAG welding process

In this research work, the results of an investigation dealing with welding of sheet metals with diverse air gap using FastROOT modified short arc welding method and short circuit MAG welding processes have been presented. Welding runs were made under different conditions and, during each run, the different process parameters were continuously monitored. It was found that maximum welding speed and less HAZ are reached under specific welding conditions with FastROOT method with the emphasis on arc stability. Welding results show that modified short arc exhibits a higher electrode melting coefficient and with virtually spatter free droplet transition. By adjusting the short circuit duration the penetration can be controlled with only a small change in electrode deposition. Furthermore, by mixing pulsed MIG welding with modified arc welding the working envelope of the process is greatly extended allowing thicker material sections to be welded with improved weld bead aesthetics. FastROOT is a modified short arc welding process using mechanized or automated welding process based on dip transfer welding, characterized by controlled material deposition during the short circuit of the wire electrode to the workpiece.

Model-based study of a chemical-looping combustion process

Chemical-looping combustion (CLC) is a novel combustion technology with inherent separation of the greenhouse gas CO2. The technique typically employs a dual fluidized bed system where a metal oxide is used as a solid oxygen carrier that transfers the oxygen from combustion air to the fuel. The oxygen carrier is looping between the air reactor, where it is oxidized by the air, and the fuel reactor, where it is reduced by the fuel. Hence, air is not mixed with the fuel, and outgoing CO2 does not become diluted by the nitrogen, which gives a possibility to collect the CO2 from the flue gases after the water vapor is condensed. CLC is being proposed as a promising and energy efficient carbon capture technology, since it can achieve both an increase in power station efficiency simultaneously with low energy penalty from the carbon capture. The outcome of a comprehensive literature study concerning the current status of CLC development is presented in this thesis. Also, a steady state model of the CLC process, based on the conservation equations of mass and energy, was developed. The model was used to determine the process conditions and to calculate the reactor dimensions of a 100 MWth CLC system with bunsenite (NiO) as oxygen carrier and methane (CH4) as fuel. This study has been made in Oxygen Carriers and Their Industrial Applications research project (2008 – 2011), funded by the Tekes – Functional Material program. I would like to acknowledge Tekes and participating companies for funding and all project partners for good and comfortable cooperation.