Ultrafiltration of pulp mill bleaching effluents

Main objective of this research was to find suitable polymeric ultrafiltration membranes with high retentions, good capacities and low fouling tendencies for the E2- and EP-effluent ultrafiltration. Purpose was to treat alkaline bleaching effluents with ultrafiltration in a way that permeates of the filtrations could be recycled back to process and the consumption of fresh water in the pulp mill could be reduced significantly. In the theoretical part of this work the challenges set by the pulp and paper indus-try processes for membranes were examined. An overview of the membrane tech-nology in the pulp industry was also provided. In addition process conditions in the chemical pulp bleaching and properties of bleaching effluents were discussed in literature study. In experimental part the E2- and EP-stage bleaching effluents from Stora Enso Imatra kraft pulp mill were ultrafiltered with CR250- and CR200-filters. Suitable membranes for ultrafiltration were chosen after screening experiments. Concentra-tion experiment was made for the E2-effluent in order to estimate water saving potential. The E2-effluent was finally ultrafiltered in the pulp mill in order to test the feasibility of ultrafiltration in a real industrial environment. Good membrane for the EP-effluent ultrafiltration based on the EP-screening ex-periments was polyethersulfone membrane UP020 with cut-off value of 20 000 Da. Polysulfone membrane UFX05 with cut-off value of 5 000 Da was promising membrane for the ultrafiltration of the E2-effluent. Based on the concentration filtration of the E2-effluent with UFX05 membrane the water saving potential could be 2.2 m3/Adt for the industrial scale ultrafiltration process. Retention re-sults, such as average COD retention of 60 %, from the trial filtration at the pulp mill with UFX05 membrane were modest compared to the screening experiments, where average COD retention was 75 %. Therefore tighter ultrafiltration mem-branes should be tested for the ultrafiltration of the E2-effluent. The UP020 mem-brane seemed to be suitable for the ultrafiltration of the EP-effluent however con-centration and pilot scale ultrafiltration experiments are needed to verify this.

Tal af John Stuart Mill

14 x 23 cm

Surface transformation hardening of carbon steel with high power fiber laser

This study investigated the surface hardening of steels via experimental tests using a multi-kilowatt fiber laser as the laser source. The influence of laser power and laser power density on the hardening effect was investigated. The microhardness analysis of various laser hardened steels was done. A thermodynamic model was developed to evaluate the thermal process of the surface treatment of a wide thin steel plate with a Gaussian laser beam. The effect of laser linear oscillation hardening (LLOS) of steel was examined. An as-rolled ferritic-pearlitic steel and a tempered martensitic steel with 0.37 wt% C content were hardened under various laser power levels and laser power densities. The optimum power density that produced the maximum hardness was found to be dependent on the laser power. The effect of laser power density on the produced hardness was revealed. The surface hardness, hardened depth and required laser power density were compared between the samples. Fiber laser was briefly compared with high power diode laser in hardening medium-carbon steel. Microhardness (HV0.01) test was done on seven different laser hardened steels, including rolled steel, quenched and tempered steel, soft annealed alloyed steel and conventionally through-hardened steel consisting of different carbon and alloy contents. The surface hardness and hardened depth were compared among the samples. The effect of grain size on surface hardness of ferritic-pearlitic steel and pearlitic-cementite steel was evaluated. In-grain indentation was done to measure the hardness of pearlitic and cementite structures. The macrohardness of the base material was found to be related to the microhardness of the softer phase structure. The measured microhardness values were compared with the conventional macrohardness (HV5) results. A thermodynamic model was developed to calculate the temperature cycle, Ac1 and Ac3 boundaries, homogenization time and cooling rate. The equations were numerically solved with an error of less than 10-8. The temperature distributions for various thicknesses were compared under different laser traverse speed. The lag of the was verified by experiments done on six different steels. The calculated thermal cycle and hardened depth were compared with measured data. Correction coefficients were applied to the model for AISI 4340 steel. AISI 4340 steel was hardened by laser linear oscillation hardening (LLOS). Equations were derived to calculate the overlapped width of adjacent tracks and the number of overlapped scans in the center of the scanned track. The effect of oscillation frequency on the hardened depth was investigated by microscopic evaluation and hardness measurement. The homogeneity of hardness and hardened depth with different processing parameters were investigated. The hardness profiles were compared with the results obtained with conventional single-track hardening. LLOS was proved to be well suitable for surface hardening in a relatively large rectangular area with considerable depth of hardening. Compared with conventional single-track scanning, LLOS produced notably smaller hardened depths while at 40 and 100 Hz LLOS resulted in higher hardness within a depth of about 0.6 mm.

A Steel Company Entering the Market Area of St. Petersburg

Tutkimuksen tavoitteena on selvittää tarkoituksenmukaisin etabloitumismenetelmä teräsyhtiön kansainvälistymisessä Pietarin markkinoille. Vaikka kansainvälistymistä onkin tutkittu paljon, kyseisen kontekstin erityispiirteisiin on aiemmissa tutkimuksissa kiinnitetty vain vähän huomiota. Kansainvälistymisteorioista työhön valittiin John Dunningin eklektinen paradigma sekä Uppsala-malli. Etabloitumismenetelmän valintaa puolestaan tarkastellaan eri vaihtoehtojen kautta, jotka kattavat viennin, suorat ulkomaan investoinnit, sopimusjärjestelyt sekä yhteisyrityksen. Valintaa selitetään taustalla vaikuttavien tekijöiden sekä kansainvälistymisprosessin kautta. Kohteena olevan markkina-alueen potentiaalin, ongelmien sekä yrityksen kilpailuetujen arvioinnin jälkeen ehdotetaan optimaalista ratkaisua. Omat haasteensa operaatiomuodon valintaan luovat potentiaalinen mutta haastava kohdemarkkina-alue sekä yrityksen sisäiset tekijät. Kontekstiin parhaiten sopivaksi etabloitumismenetelmäksi esitetään aloittamista välittömällä viennillä asiakkaiden etsimiseksi ja suhteiden luomiseksi. Kun asiakkuuksia alueella on riittävästi, myyntikonttorin perustaminen Pietarin lähelle nähdään tarkoituksenmukaisena paikallisen läsnäolon lisäämiseksi. Empiirinen data kattaa kahdeksan asiantuntijahaastattelua, jotka yhdessä muun lähdeaineiston kanssa rakentavat perustan empiirisille tuloksille. Tutkimuksen tulokset tarjoavat yritykselle perustellun ratkaisuehdotuksen siitä, kuinka Pietarin markkinoille tulisi etabloitua.

Risk management measures for REACH registered intermediate substances in pulp mill

Tämän työn tavoitteena on antaa kuvaus riskinhallintamenetelmistä viidelle välituotekemikaalille, joita käytetään Stora Enson Imatran tehtailla. Välituotekemikaalit ovat mustalipeä, viherlipeä, valkolipeä, natriumbisulfiitti ja natriumsulfiitti. Nämä kemikaalit ovat jo rekisteröityjä ECHA:an ja rekisteröintiin liittyen ECHA:an on toimitettava myös kuvaus riskinhallintamenetelmistä. Työn alussa kuvaillaan työn kannalta olennaiset säädökset ja viranomaiset, jotka valvovat kemikaalien käyttöä ja valmistusta Euroopan Unionin alueella. Tämän jälkeen kerrotaan yleisesti välituotekemikaalien rekisteröintikriteereistä. Työn loppuosa käsittää kuvauksen riskinhallintamenetelmistä jokaiselle kemikaalille. Riskinhallintamenetelmät sisältävät eristyksen teknisin keinoin, menettelytapa- ja valvontatekniikat, johtamistavat ja henkilökunnan koulutuksen ja välituotekemikaalien kuljetuksen. Myös jokaisen kemikaalin ominaisuudet on kuvattu ja lyhyt prosessikuvaus kemikaalien valmistuksesta ja käytöstä on esitetty helpottamaan ymmärtämistä.

Tertiary Treatment and Re-use of Kraft Pulp Mill Effluent

The efficient use of materials and natural recourses, for ecological and economic reasons, has become more and more important in all industries. In the forest industries this means higher levels of closure in the material circulations of the mills. One possibility to reduce wastewater discharge is to re-use part of the 2nd clarifier effluent as process water. The main target of this thesis was to evaluate the technical suitability of several mechanical and chemical tertiary treatment methods for water re-use. Some of the tested methods seemed to have high potential for the removal of some specific constituents from the wastewater. Tertiary treatment is needed because higher levels of closure may cause problems with increasing amounts of non-process elements in different points of kraft pulp process. The aspect of sustainable development was taken into account by evaluating positive and negative environmental effects of the treatment processes. Environmental benefits can be gained by using some of the tertiary treatment methods tested. These methods should still be researched more for system optimization.

Improving the Supply Chain Performance Management System in a Finnish paper mill

This Master’s Thesis studies performance management system and its benefits, risks and costs. Objective of the thesis is to describe and evaluate currently used supply chain performance management system (SCPMS) in a Finnish paper mill and its interfaces with its business unit’s SCPMS. As a result, the host company has improvement road map for improving its SCPMS. Used SCPMS in the host company and its interfaces to business unit’s SCPMS are described based on interviews held in the host company and the business unit. Evaluation of the host company’s SCPMS is based on literature study. For improvement road map, three areas in need of improvements are chosen. The study shows the need of high level top management commitment in successful performance management system implementation and usage, especially when the system is deployed to lower levels in the organization.

Ultimate capacity of stainless steel rectangular hollow section X- joints at low temperatures

Growing demand for stainless steel construction materials has increased the popularity of substitutive materials for austenitic stainless steels. The lean duplex grades have taken their place in building of structures exposed to corrosive environments. Since the duplex grades are relatively new materials, the current codes and norms do not fully cover the newest duplex grades. The joints tested in this thesis were designed and studied according to Eurocode 3, even though all the materials are not yet accepted to the standards. The main objective in this thesis was to determine the differences of the used materials in behaviour under loading at low temperatures. Tests in which the deformation and strength properties of the joints were determined were done at the temperature of -46°C, which is the requirement of temperature for structures designed according to Norsok standards. Results show that replacing the austenitic grade with the lean duplex grade is acceptable.

The effect of shielding gas feeding method in laser welding of steel

Gas shielding plays an important role in laser welding phenomena. This is because it does not only provide shielding against oxidization but it has an effect in beam absorption and thus welds penetration. The goal of this thesis is to study and compare the effects of different shielding gas feeding methods in laser welding of steel. Research method is a literature survey. It is found that the inclination angle and the arrangement of the gas feeding nozzles affect the phenomena significantly. It is suggested that by designing shielding gas feeding case specifically better welding results can be obtained.

Modal testing and numerical modeling of the dynamic properties of layered sheet-steel structure

Recently, due to the increasing total construction and transportation cost and difficulties associated with handling massive structural components or assemblies, there has been increasing financial pressure to reduce structural weight. Furthermore, advances in material technology coupled with continuing advances in design tools and techniques have encouraged engineers to vary and combine materials, offering new opportunities to reduce the weight of mechanical structures. These new lower mass systems, however, are more susceptible to inherent imbalances, a weakness that can result in higher shock and harmonic resonances which leads to poor structural dynamic performances. The objective of this thesis is the modeling of layered sheet steel elements, to accurately predict dynamic performance. During the development of the layered sheet steel model, the numerical modeling approach, the Finite Element Analysis and the Experimental Modal Analysis are applied in building a modal model of the layered sheet steel elements. Furthermore, in view of getting a better understanding of the dynamic behavior of layered sheet steel, several binding methods have been studied to understand and demonstrate how a binding method affects the dynamic behavior of layered sheet steel elements when compared to single homogeneous steel plate. Based on the developed layered sheet steel model, the dynamic behavior of a lightweight wheel structure to be used as the structure for the stator of an outer rotor Direct-Drive Permanent Magnet Synchronous Generator designed for high-power wind turbines is studied.

Production planning and optimization of a pulp mill: introduction of the optimisation based scheduling software for pulp industry

The objective of this project was to introduce a new software product to pulp industry, a new market for case company. An optimization based scheduling tool has been developed to allow pulp operations to better control their production processes and improve both production efficiency and stability. Both the work here and earlier research indicates that there is a potential for savings around 1-5%. All the supporting data is available today coming from distributed control systems, data historians and other existing sources. The pulp mill model together with the scheduler, allows what-if analyses of the impacts and timely feasibility of various external actions such as planned maintenance of any particular mill operation. The visibility gained from the model proves also to be a real benefit. The aim is to satisfy demand and gain extra profit, while achieving the required customer service level. Research effort has been put both in understanding the minimum features needed to satisfy the scheduling requirements in the industry and the overall existence of the market. A qualitative study was constructed to both identify competitive situation and the requirements vs. gaps on the market. It becomes clear that there is no such system on the marketplace today and also that there is room to improve target market overall process efficiency through such planning tool. This thesis also provides better overall understanding of the different processes in this particular industry for the case company.

Welding of additively manufactured stainless steel parts: Comparative study between sheet metal and selective laser melted parts

Additive manufacturing is a fast growing manufacturing technology capable of producing complex objects without the need for conventional manufacturing process planning. During the process the work piece is built by adding material one layer at a time according to a digital 3D CAD model. At first additive manufacturing was mainly used to make prototypes but the development of the technology has made it possible to also make final products. Welding is the most common joining method for metallic materials. As the maximum part size of additive manufacturing is often limited, it may sometimes be required to join two or more additively manufactured parts together. However there has been almost no research on the welding of additively manufactured parts so far, which means that there has been very little information available on the possible differences compared to the welding of sheet metal parts. The aim of this study was to compare the weld joint properties of additively manufactured parts to those of sheet metal parts. The welding process that was used was TIG welding and the test material was 316L austenitic stainless steel. Weld joint properties were studied by making tensile, bend and hardness tests and by studying the weld microstructures with a microscope. Results show that there are certain characteristics in the welds of additively manufactured parts. The building direction of the test pieces has some impact on the mechanical properties of the weld. Nevertheless all the welds exhibited higher yield strength than the sheet metal welds but at the same time elongation at break was lower. It was concluded that TIG welding is a feasible process for welding additively manufactured parts.

Sinkityslinjan pesuosan optimointi

Työn tavoitteena oli sinkityslinjan pesuosan toiminnan optimointi. Teoriakatsauksen ja haastattelututkimusten avulla työssä selvitettiin, mitkä tekijät pesuosalla tai teräsnauhan pesua edeltävissä prosessivaiheissa vaikuttavat pesutehoon alentavasti. Pesuosan ajoparametrien muutoskokeiden avulla määritettiin kunkin pesuparametrin suhteellinen vaikutus pesutulokseen sekä pesuosan optimaaliset ajoparametrit. Vaikutuksia arvioitiin pinnanpuhtauden ja pesuvesien laboratorioanalyysien sekä prosessidatan avulla. Jätevesianalyysien ja prosessidatan avulla arvioitiin lisäksi pesuosan muutosten vaikutusta pesusta syntyviä jätevesiä käsittelevän jätevesilaitoksen toimintaan. Laitetestauksen avulla työssä kartoitettiin, mikä menetelmä pinnanpuhtauden määrittämiseen soveltuu pesuosalle parhaiten. Kustannusarvioinnilla selvitettiin, millä toimin pesuosan toimintavarmuutta on edullisinta ylläpitää. Työn tulosten pohjalta lämpötilalla todettiin olevan pesutuloksen kannalta merkittävin vaikutus. Sen sijaan kemikaaliannostelun merkitys oli vähäinen. Vesien säännöllisen uudistamisen todettiin olevan olennainen pesuvesien ylläpitokeino nykyisessä pesutilanteessa. Se todettiin lisäksi ennakoivana toimenpiteenä kannattavammaksi kuin pesuosan täystyhjäykset ongelmatilanteissa. Teippitestein määritettävälle pinnanpuhtaudelle katsottiin sopivaksi vaihteluväliksi 40–75 %. Työssä todettiin, että pesua edeltävän kylmävalssin valssiöljyn vaihto sekä valssilla tuotetun teräsnauhan pinnanpuhtaus vaikuttavat merkittävästi pesuosan toimintakykyyn ja pesuosan pyörittämisestä aiheutuviin kustannuksiin. Toimenpiteet pesuosalla vaikuttavat lisäksi jätevesilaitoksen käsittelyvaatimuksiin, joskin myös tasaavat sen toimintaa. Työssä ehdotettiin ratkaisukeinoja pesuosan toimintavarmuuden varmistamiseksi jatkossa, sekä tarjottiin työkaluja, joiden avulla tulevissa investointipäätöksissä voidaan ottaa huomioon myös pesuosan toiminnan edellytykset.

Computational studies of deformation in stainless steel rings due to torch heating

A support ring of AISI 304L stainless steel that holds vertical, parallel wires arranged in a circle forming a cylinder is studied. The wires are attached to the ring with heat-induced shrinkage. When the ring is heated with a torch the heat affected zone tries to expand while the adjacent cool structure obstructs the expansion causing upsetting. During cooling, the ring shrinks smaller than its original size clamping the wires. The most important requirement for the ring is that it should be as round as possible and the deformations should occur as overall shrinkage in the ring diameter. A three-dimensional nonlinear transient sequential thermo-structural Abaqus model is used together with a Fortran code that enters the heat flux to each affected element. The local and overall deformations in one ring inflicted by the heating are studied with a small amount of inspection on residual stresses. A variety of different cases are chosen to be studied with the model constructed to provide directional knowledge; torch flux with the means of speed, location of the wires, heating location and structural factors. The decrease of heating speed increases heat flux that rises the temperature increasing shrinkage. In a single progressive heating uneven distribution of shrinkage appears to the start/end region that can be partially fixed with using speeded heating’s to strengthen the heating of that region. Location of the wires affect greatly to the caused shrinkage unlike heating location. The ring structure affects also greatly to the shrinkage; smaller diameter, bigger ring height, thinner thickness and greater number of wires increase shrinkage.

Modelling Cutting States in Rough Turning of 34CrNiMo6 Steel

Rough turning is an important form of manufacturing cylinder-symmetric parts. Thus far, increasing the level of automation in rough turning has included process monitoring methods or adaptive turning control methods that aim to keep the process conditions constant. However, in order to improve process safety, quality and efficiency, an adaptive turning control should be transformed into an intelligent machining system optimizing cutting values to match process conditions or to actively seek to improve process conditions. In this study, primary and secondary chatter and chip formation are studied to understand how to measure the effect of these phenomena to the process conditions and how to avoid undesired cutting conditions. The concept of cutting state is used to address the combination of these phenomena and the current use of the power capacity of the lathe. The measures to the phenomena are not developed based on physical measures, but instead, the severity of the measures is modelled against expert opinion. Based on the concept of cutting state, an expert system style fuzzy control system capable of optimizing the cutting process was created. Important aspects of the system include the capability to adapt to several cutting phenomena appearing at once, even if the said phenomena would potentially require conflicting control action.