Power of Photos and Video in Education

Konferenssiesitelmä: PHOTOGRAPHY NEXT International Conference at Moderna museet and Nordiska Museet, Stockholm, 4-5 February, 2010

Performance of high power fibre laser cutting of thick-section steel and mediumsection aluminium

Cutting of thick section stainless steel and mild steel, and medium section aluminium using the high power ytterbium fibre laser has been experimentally investigated in this study. Theoretical models of the laser power requirement for cutting of a metal workpiece and the melt removal rate were also developed. The calculated laser power requirement was correlated to the laser power used for the cutting of 10 mm stainless steel workpiece and 15 mm mild steel workpiece using the ytterbium fibre laser and the CO2 laser. Nitrogen assist gas was used for cutting of stainless steel and oxygen was used for mild steel cutting. It was found that the incident laser power required for cutting at a given cutting speed was lower for fibre laser cutting than for CO2 laser cutting indicating a higher absorptivity of the fibre laser beam by the workpiece and higher melting efficiency for the fibre laser beam than for the CO2 laser beam. The difficulty in achieving an efficient melt removal during high speed cutting of the 15 mmmild steel workpiece with oxygen assist gas using the ytterbium fibre laser can be attributed to the high melting efficiency of the ytterbium fibre laser. The calculated melt flow velocity and melt film thickness correlated well with the location of the boundary layer separation point on the 10 mm stainless steel cut edges. An increase in the melt film thickness caused by deceleration of the melt particles in the boundary layer by the viscous shear forces results in the flow separation. The melt flow velocity increases with an increase in assist gas pressure and cut kerf width resulting in a reduction in the melt film thickness and the boundary layer separation point moves closer to the bottom cut edge. The cut edge quality was examined by visual inspection of the cut samples and measurement of the cut kerf width, boundary layer separation point, cut edge squareness (perpendicularity) deviation, and cut edge surface roughness as output quality factors. Different regions of cut edge quality in 10 mm stainless steel and 4 mm aluminium workpieces were defined for different combinations of cutting speed and laserpower.Optimization of processing parameters for a high cut edge quality in 10 mmstainless steel was demonstrated

Distributed ControlArchitecture of Power Electronics Building-Block-Based Frequency Converters

The increasing power demand and emerging applications drive the design of electrical power converters into modularization. Despite the wide use of modularized power stage structures, the control schemes that are used are often traditional, in other words, centralized. The flexibility and re-usability of these controllers are typically poor. With a dedicated distributed control scheme, the flexibility and re-usability of the system parts, building blocks, can be increased. Only a few distributed control schemes have been introduced for this purpose, but their breakthrough has not yet taken place. A demand for the further development offlexible control schemes for building-block-based applications clearly exists. The control topology, communication, synchronization, and functionality allocationaspects of building-block-based converters are studied in this doctoral thesis. A distributed control scheme that can be easily adapted to building-block-based power converter designs is developed. The example applications are a parallel and series connection of building blocks. The building block that is used in the implementations of both the applications is a commercial off-the-shelf two-level three-phase frequency converter with a custom-designed controller card. The major challenge with the parallel connection of power stages is the synchronization of the building blocks. The effect of synchronization accuracy on the system performance is studied. The functionality allocation and control scheme design are challenging in the seriesconnected multilevel converters, mainly because of the large number of modules. Various multilevel modulation schemes are analyzed with respect to the implementation, and this information is used to develop a flexible control scheme for modular multilevel inverters.

Doubly fed induction generator versus direct drive permanent magnet synchronous generator in wind power applications

The objective of this master's thesis is to compare two different generator systems for wind turbines. It is the doubly fed induction generator system with three stage gearbox and the direct drive permanent magnet generator system. The comparison of generator systems is based on annual energy production for a given wind climate. For comparison a 3 MW, 15 rpm wind turbine is used. Modelling of a turbine rotor, gearbox and converters were done. Design of two generators was done and their performance was examined.

Indian female gurus in contemporary in Hinduism : a study of central aspects and expressions of their religious leadership

Den rikt utformade och komplexa hinduiska traditionen har hittills huvudsakligen tecknats av manliga forskare och det är främst manliga religiösa strävanden som har dokumenterats. Detta förhållande och de patriarkala synsätt som styr många auktoritativa heliga texter har bidragit till att skapa intrycket att hinduiska kvinnors religiösa erfarenheter antingen saknas eller är avsevärt begränsade. Denna studie lyfter fram det faktum att ett ökande antal indiska kvinnor inom dagens hinduism axlar publika roller som religiösa ledare. Med sitt framträdande utmanar många av dessa rådande sociala uppfattningar om kvinnors underordnade ställning och främjar därmed en förnyad medvetenhet av urgamla föreställningar om Gud som kvinna. Avhandlingen utforskar fenomenet kvinnliga guruer genom att belysa sjuttio guruers andliga karriär, med särskild fokus på fyra av dem. Några av de frågor som behandlas är följande: På vilket sätt är kvinnliga guruer del av den hinduiska traditionen? Vilka förväntningar ställs på dem? Hur legitimeras deras auktoritet som guruer? Hur handskas guruerna med sina dubbla roller som kvinnor och andliga ledare? Hur återspeglas gudinnans ställning, som i indisk religiositet ofta är central, i kvinnors faktiska verklighet? Bidrar kvinnliga guruer med sitt religiösa engagemang till att nyskapa och förändra den indiska religiösa diskursen och utövningen av religion?

Faster for the master! : exploring issues of religious expression and alternative Christian identity within the Finnish Christian metal music scene

Populärkulturen har i dagens läge kommit att utgöra en allt mer viktig och central inspirationskälla för allt fler människors konstruktion av den egna religiösa identiteten även inom traditionella och institutionella kristna sammanhang. Denna avhandling belyser denna utveckling i ljuset av den finländska kristna metallmusik-kulturen - en sällsynt stark sammanblanding av protestantisk kristendom och en utpräglad och kontroversiell populärmusikform och dess kultur. Fokus riktas framför allt på hur den kristna metallmusik-kulturen blir meningsfull för sina medlemmar genom de sätt på vilka den konstrueras diskursivt, dvs. genom de sätt på vilka den representeras och talas om bland sina egna anhängare. Den diskursiva konstruktionen av den kristna metallmusik-kulturen utforskas på ett såväl bredare transnationellt som ett finländskt nationellt plan. Studien redogör även för den kristna metalmusikens och -kulturens huvudsakliga verbala, visuella och estetiska kännetecken. Uppbyggnaden och spridningen av dagens transnationella kristna metallmusik-kultur undersöks även i ljuset av det teoretiska konceptet scene. Avhandlingens centrala argument är att den kristna metallmusikscenen erbjuder sina medlemmar en mängd resurser för skapandet av ett alternativt och komplementärt religiöst uttrycksätt, religiös praxis och en alternativ kristen identitet.

Methods and Models for Accelerating Dynamic Simulation of Fluid Power Circuits

The objective of this dissertation is to improve the dynamic simulation of fluid power circuits. A fluid power circuit is a typical way to implement power transmission in mobile working machines, e.g. cranes, excavators etc. Dynamic simulation is an essential tool in developing controllability and energy-efficient solutions for mobile machines. Efficient dynamic simulation is the basic requirement for the real-time simulation. In the real-time simulation of fluid power circuits there exist numerical problems due to the software and methods used for modelling and integration. A simulation model of a fluid power circuit is typically created using differential and algebraic equations. Efficient numerical methods are required since differential equations must be solved in real time. Unfortunately, simulation software packages offer only a limited selection of numerical solvers. Numerical problems cause noise to the results, which in many cases leads the simulation run to fail. Mathematically the fluid power circuit models are stiff systems of ordinary differential equations. Numerical solution of the stiff systems can be improved by two alternative approaches. The first is to develop numerical solvers suitable for solving stiff systems. The second is to decrease the model stiffness itself by introducing models and algorithms that either decrease the highest eigenvalues or neglect them by introducing steady-state solutions of the stiff parts of the models. The thesis proposes novel methods using the latter approach. The study aims to develop practical methods usable in dynamic simulation of fluid power circuits using explicit fixed-step integration algorithms. In this thesis, twomechanisms whichmake the systemstiff are studied. These are the pressure drop approaching zero in the turbulent orifice model and the volume approaching zero in the equation of pressure build-up. These are the critical areas to which alternative methods for modelling and numerical simulation are proposed. Generally, in hydraulic power transmission systems the orifice flow is clearly in the turbulent area. The flow becomes laminar as the pressure drop over the orifice approaches zero only in rare situations. These are e.g. when a valve is closed, or an actuator is driven against an end stopper, or external force makes actuator to switch its direction during operation. This means that in terms of accuracy, the description of laminar flow is not necessary. But, unfortunately, when a purely turbulent description of the orifice is used, numerical problems occur when the pressure drop comes close to zero since the first derivative of flow with respect to the pressure drop approaches infinity when the pressure drop approaches zero. Furthermore, the second derivative becomes discontinuous, which causes numerical noise and an infinitely small integration step when a variable step integrator is used. A numerically efficient model for the orifice flow is proposed using a cubic spline function to describe the flow in the laminar and transition areas. Parameters for the cubic spline function are selected such that its first derivative is equal to the first derivative of the pure turbulent orifice flow model in the boundary condition. In the dynamic simulation of fluid power circuits, a tradeoff exists between accuracy and calculation speed. This investigation is made for the two-regime flow orifice model. Especially inside of many types of valves, as well as between them, there exist very small volumes. The integration of pressures in small fluid volumes causes numerical problems in fluid power circuit simulation. Particularly in realtime simulation, these numerical problems are a great weakness. The system stiffness approaches infinity as the fluid volume approaches zero. If fixed step explicit algorithms for solving ordinary differential equations (ODE) are used, the system stability would easily be lost when integrating pressures in small volumes. To solve the problem caused by small fluid volumes, a pseudo-dynamic solver is proposed. Instead of integration of the pressure in a small volume, the pressure is solved as a steady-state pressure created in a separate cascade loop by numerical integration. The hydraulic capacitance V/Be of the parts of the circuit whose pressures are solved by the pseudo-dynamic method should be orders of magnitude smaller than that of those partswhose pressures are integrated. The key advantage of this novel method is that the numerical problems caused by the small volumes are completely avoided. Also, the method is freely applicable regardless of the integration routine applied. The superiority of both above-mentioned methods is that they are suited for use together with the semi-empirical modelling method which necessarily does not require any geometrical data of the valves and actuators to be modelled. In this modelling method, most of the needed component information can be taken from the manufacturer’s nominal graphs. This thesis introduces the methods and shows several numerical examples to demonstrate how the proposed methods improve the dynamic simulation of various hydraulic circuits.

RF disturbances produced by high-power photovoltaic solar plants

In this thesis, analysis of electromagnetic compatibility of high-power photovoltaic solar plant is made. Current standards suitable for photovoltaic applications are given. Measurements of antenna factor for experimental setup are shown. Also, measurements of common mode disturbance voltages in high-power solar plant are given. Importance of DC-side filter is shown. In the last part of the work, electromagnetic simulations are made. These simulations show influence of several factors to EMC of power plant. Based on these simulations and measurements recommendations are given.

Design of marine generators for alternative diesel-electric power systems

This study compares different electric propulsion systems. Results of the analysis of all the advantages and disadvantages of the different propulsion systems are given. This thesis estimates possibilities to apply different diesel-electric propulsion concepts for different vessel types. Small and medium size vessel’s power ranges are studied. The optimal delivery system is chosen. This choice is made on the base of detailed study of the concepts, electrical equipment market and comparison of mass, volume and efficiency parameters. In this thesis three marine generators are designed. They are: salient pole synchronous generator and two permanent magnet synchronous generators. Their electrical, dimensional, cost and efficiency parameters are compared. To understand all the benefits diagrams with these parameters are prepared. Possible benefits and money savings are estimated. As the result the advantages, disadvantages and boundary conditions for the permanent magnet synchronous generator application in marine electric-power systems are found out.

Economics of combined power plant and pyrolysis bio-oil production

There are reasons of necessity in bio-fuel use and bio-energy fast development. It includes the material about bio-energy technologies, applications and methods. There are basic thermodynamics and economic theories. The economic calculation presents the comparison between two combinations. There are boiler plant below 20 MW in combination with ablative pyrolysis plant for bio-oil production and CHP plant below 100 MW in combination with the RTP pyrolysis bio-oil production technology. It provides a material about wood chips and bio-oil characteristics and explains it nature, presents the situation around the bio-fuel market or bio-fuel trade. There is a description of pyrolysis technologies such as ablative and RTP. The liquid product of the pyrolysis processes is bio-oil. The bio-oil could be different even of the same production process, because of the raw material nature and characteristics. The calculation shows advantages and weaknesses of combinations and obtained a proof of suppositions. The next thing, proven by this work is the fact that to get more efficiency from energy project it is good possibility to built plants in combinations.

Religious women in Britain reappraised

Kirjallisuusarvostelu

Employer Branding in Power Industry

Companies invest in employer branding in order to get good applicants, retain employees and create the image of a great employer. Employer branding will become more prominent in the future because companies strive to gain competitive advantage. Power industry is an internationally remarkable field of business. Energy and the solutions of power technology are always needed and there is a major need for new experts in power industry. The competition of talented workforce will increase because of the decrease in working-age population. The fundamental purpose of this study is to examine what kind of motives and practices company has for employer branding in power industry. The objective is to find out the benefits of employer branding and how it is targeted towards potential and current employees. In addition, the aim is to examine whether companies see employer branding as a process and what kind of processes they have for employer branding. The theoretical contribution of this study is based on literature review, which provides a better understanding of employer branding. The empirical part is a qualitative case study of two large and international companies in the field of power industry. Employer branding in the case companies is examined using theme interviews. According to this study, employer branding is a significant part of companies’ business in power industry. The main motives for employer branding are better employer image, more efficient recruitment and improved job satisfaction. Employer branding is communicated and targeted according to target group. Recruitment and educational co-operation are the main objects of employer branding towards potential employees, whereas training and development are an essential part of employer branding towards current employees. This study also discovers that there is some kind of process aspect in the background of employer branding.

Rukoile ja työtä tee. Onni Puhakan kehitys innovaattorista oman tien kulkijaksi

Pray and work. The development of Onni Puhakka: from innovator to nonconformist This ethnological biographical study examines the modernization which began in the mid-1800s, continued into the mid-1900s, and has changed Finnish society in many ways. This era has been studied on a general level quite extensively, but this work explores the life and everyday experiences of Onni Puhakka (1870−1955), a farmer who spent most of his life in the town of Liperi. The goal is to find new perspectives on the development of the modernization process in society through the experiences of an individual. In this study, a central theme is the rural co-operative movement represented in Finland by Pellervo as well as its development in this country and as a significant undertaking in Onni Puhakka’s life. The co-operative movement was one of the most significant sectors affecting modernization in rural communities. The main character in the study is the grandfather of the present author, and thus this research belongs to the newly accepted ethnological research tradition of studying one’s own community. Written documents, mainly collected and preserved by Onni Puhakka himself during his lifetime, form the research material. The material consists mainly of Puhakka’s extensive correspondence, personal notes and diaries, documents related to his farm, and photographs taken by him. Earlier research and other written material examining the general development of the period were used to provide a background for the study. The co-operative movement formed a comprehensive ideology for Onni Puhakka, in which the possibilities for the development of both individuals and the community were combined. His life was based on a religious conviction, and he felt that the co-operative movement was the application of Christian love for one’s neighbour in practice. At the beginning of his active working career, Puhakka was an innovator, a reformer at the forefront of progress, but quite soon he became a sworn critic of the development of the co-operative movement in particular. One of Puhakka’s criticisms of the co-operative movement was the shifting of decision-making power to professional managers and central organizations, far from the reach of local actors. A fundamental reason for his dissatisfaction was the development within the co-operative movement in which the ideological background was forgotten, and economic goals and making a profit took an excessive significance. This assessment of the co-operative movement made by Onni Puhakka and his predictions about its development were not unfounded. This has been shown by several studies examining the development of both the Pellervo and working class cooperative movements. The professionalization of management, managerialism, as well as the direct links between professional managers of local co-operatives and central organizations have lead to the situation in which fewer and fewer people make the decisions, and management has as its goal economic success and growth. Co-operative enterprises that have grown in size have become estranged from the everyday life of their members. Instead of taking care of relations with the membership of the co-op, competitive ability and the market share have become the most important concerns of the management. As the membership has become alienated, their interest in large-scale co-ops has also become largely economic. A significant change among the membership of the Pellervo movement occurred at the stage when the co-operative movement shifted from rural areas to urban centres. This meant that the commitment of the membership became much looser than it had been in the farmers’ production and consumer co-ops. From the point of view of its members, the nature of the co-operative movement has become diametrically opposed to its point of departure: the active members who previously formed the subject of the co-operative movement have become the object of the economic activities of that same movement. The co-operative movement has been transformed from the progressive agent of change of its early years into a business activity which no longer has any significant task as a social reformer. This study confirms the observations of the latest research on modernization which states that modernization has not been a straightforward and inevitable development that has lead to the present situation. For example, the criticism directed by Puhakka toward the co-operative movement includes information that shows that a few others who were initially actively involved also criticized the development of the movement. Despite his occasional frustration, Onni Puhakka continued his criticism and attempts to get the co-operative movement to change its course and return to its ‘roots’. In the early years of the cooperative movement he probably did not differ much from the other pioneers in the sense that many of them had adopted and internalized the same values and motive for being involved that he had. However, Puhakka differed from his colleagues in the sense that he was able to believe in what he called the “fundamental values” of the co-operative movement longer than many of them.

Requirement management in nuclear power projects

Diplomityön tarkoituksena oli tutkia vaatimusten hallintaa suunnittelu- ja konsultointiyrityksen kannalta Suomen ydinvoimaprojekteissa keskittyen ydinturvallisuus- ja laatuvaatimuksiin. Ydinvoimaprojekteissa toimiminen on edellyttänyt menettelyohjeiden ja laatujärjestelmän uudelleen organisointia yrityksessä ja esiin on noussut haasteita liittyen muun muassa vaatimusten tunnistamiseen ja todentamiseen erityyppisissä ja erilaajuisissa projekteissa. Työ toteutettiin perehtymällä ydinvoimaan liittyvään lainsäädäntöön Suomessa, ohjeisiin ja standardeihin sekä haastattelemalla yrityksen omia asiantuntijoita. Viimeaikaisista sekä meneillään olevista projekteista kerättiin kokemuksia sekä arvioitiin ydinvoima projekteja varten laaditun projektin toteutusohjeen toimivuutta ja käytettävyyttä esimerkkiprojektin avulla. Suurimmiksi haasteiksi tunnistettiin lainsäädännöllisten vaatimusten, kuten ydinvoima- laitosohjeiden (YVL) muuttuminen ja tulkinnanvaraisuus sekä asiakkaiden perehtymät- tömyys Suomen lainsäädäntöön ja vaatimustasoon liittyen ydinturvallisuuteen. Työn tuloksena tunnistettiin hyviä vaatimusten hallintaan liittyviä projektinhallintaa ja ydin- turvallisuutta edistäviä asioita, kuten vaatimusten täsmentäminen jo sopimustasolla sekä niiden täyttymisen seuranta projektin aikana. Erillisen vaatimustietokannan luomista ydinvoimaprojekteja varten tutkittiin, mutta siitä luovuttiin teknisten vaatimusten osalta kannattamattomana, sillä standardien ja vaatimusten määrä kasvoi niin suureksi, että niiden hallitseminen vaatisi enemmän työtä kuin mitä projektien taso yleensä sallisi.