Tuplakuori-rakenne eristettyihin muoviputkiin

Eristettyjen muoviputkien kuljetus- tai asennusvaiheessa on mahdollista, että putken suojakuori rikkoutuu mekaanisen iskun vaikutuksesta ja putken sisään pääsee vettä. Huonoimmassa tapauksessa vesi pääsee etenemään suojakuoren ja eristekerroksen välissä talon sisälle ja aiheuttaa mittavat kosteusvahingot. Tämän diplomityön tarkoituksena oli selvittää, onko eristetylle muoviputkelle mahdollista toteuttaa tuotantotaloudellisesti tuplakuori-rakenne. Tuplakuoren tarkoituksena oli tässä työssä estää putken sisärakenteisiin päässeen veden eteneminen putken pitkittäissuunnassa. Diplomityössä käsiteltiin muutamia vaihtoehtoisia ratkaisuja toteuttaa tuplakuori-rakenne joista lopulta päädyttiin keskittymään muovikalvon käyttöön. Muovikalvon käytöllä oli lähinnä kaksi tarkoitusta. Tärkeimpänä oli saada muovikalvo sulamaan eristekerroksen ja suojakuoren väliin. Tällöin sulanut muovikalvo toimisi liiman tavoin ja hitsaisi eristekerroksen ja suojakuoren toisiinsa kiinni. Näin veden eteneminen eristekerroksen ja suojakuoren välissä saataisiin estetyksi. Muovikalvo oli myös tarkoitus kiristää eristepaketin päälle niin kireälle, että eristepaketin halkaisijaa saataisiin pienennettyä. Muovikalvon käyttöön perehdyttiin suorittamalla tuotantolinjalla koeajoja. Koeajoissa kokeiltiin erilaisia ja erikokoisia putkituotteita erilaisilla tuotantoparametreilla. Näin pyrittiin löytämään parhaat parametrit ja arvot, joilla muovikalvoa pystyttäisiin tulevaisuudessa käyttämään jatkuvassa tuotannossa. Koeajojen tuloksista voitiin havaita, että kalvoitetut putkituotteet käyttäytyivät tuotannossa hyvin eri tavoin.

Biochemical Modification of Thermomechanical Pulp Fibers

The first objective of this study was to find out reliable laboratory methods to predict the effect of enzymes on specific energy consumption and fiber properties of TMP pulp. The second one was to find with interactive software called “Knowledge discovery in databases” enzymes or other additives that can be used in finding a solution to reduce energy consumption of TMP pulp. The chemical composition of wood and enzymes, which have activity on main wood components were presented in the literature part of the work. The results of previous research in energy reduction of TMP process with enzymes were also highlighted. The main principles of knowledge discovery have been included in literature part too. The experimental part of the work contains the methods description in which the standard size chip, crushed chip and fiberized spruce chip (fiberized pulp) were used. Different types of enzymatic treatment with different dosages and time were tested during the experiments and showed. Pectinase, endoglucanase and mixture of enzymes were used for evaluation of method reliability. The fines content and fiber length of pulp was measured and used as evidence of enzymes' effect. The refining method with “Bauer” laboratory disc refiner was evaluated as not highly reliable. It was not able to provide high repeatability of results, because of uncontrolled feeding capacity and refining consistency. The refining method with Valley refiner did not have a lot of variables and showed stable and repeatable results in energy saving. The results of experiments showed that efficient enzymes impregnation is probably the main target with enzymes application for energy saving. During the work the fiberized pulp showed high accessibility to enzymatic treatment and liquid penetration without special impregnating equipment. The reason was that fiberized pulp has larger wood surface area and thereby the contact area between the enzymatic solution and wood is also larger. Standard size chip and crushed chip treatment without special impregnator of enzymatic solution was evaluated as not efficient and did not show visible, repeatable results in energy consumption decrease. Thereby it was concluded that using of fiberized pulp and Valley refiner for measurements of enzymes' effectiveness in SEC decrease is more suitable than normal size chip and crushed chip with “Bauer” refiner. Endoglucanase with 5 kg/t dosage showed about 20% energy consumption decrease. Mixture of enzymes with 1.5 kg/t dosage showed about 15% decrease of energy consumption during the refining. Pectinase at different dosages and treatment times did not show significant effect on energy consumption. Results of knowledge discovery in databases showed the xylanase, cellulase and pectinase blend as most promising for energy reduction in TMP process. Surfactants were determined as effective additives for energy saving with enzymes.

Sähköautojen pikalatauksen verkkovaikutukset

Euroopan unionin energiapolitiikka on luonut paineen parantaa energiatehokkuutta kaikilla energiankäytön aloilla. Merkittävä osa energiasta kulutetaan liikenteessä, joten sähköautojen käyttöönotolla voidaan parantaa energiatehokkuutta merkittävästi. Tämän vuoksi on tarkasteltava sähköautojen laajamittaisen levinneisyyden aiheuttamia vaikutuksia sähköverkolle. Tässä diplomityössä tarkastellaan sähköautojen pikalatauksen verkkovaikutuksia. Tarkastelu painottuu kotilatauksen tarkasteluun taajamissa ja maaseudulla. Kuormituksen kasvu simuloidaan hyödyntäen sähköauton lataukselle laskettua kuormituskäyrää, jonka laskenta perustuu keskimääräiseen henkilöauton liikkumiseen, joka on saatavilla Suomen henkilöliikennetutkimuksesta. Simuloinnin tulosten perusteella sähköauton pikalatauksen verkkovaikutukset ovat merkittäviä keskijänniteverkossa ja pienjänniteverkossa. Suuremmat vaikutukset kohdistuvat pienjänniteverkkoon.

Usability of laser–arc hybrid welding processes in industrial applications

Metal industries producing thick sections have shown increasing interest in the laser–arc hybrid welding process because of its clear advantages compared with the individual processes of autogenous laser welding and arc welding. One major benefit of laser–arc hybrid welding is that joints with larger gaps can be welded with acceptable quality compared to autogenous laser welding. The laser-arc hybrid welding process has good potential to extend the field of applications of laser technology, and provide significant improvements in weld quality and process efficiency in manufacturing applications. The objective of this research is to present a parameter set-up for laser–arc hybrid welding processes, introduce a methodical comparison of the chosen parameters, and discuss how this technology may be adopted in industrial applications. The research describes the principles, means and applications of different types of laser–arc hybrid welding processes. Conducted experiment processing variables are presented and compared using an analytical model which can also be used for predictive simulations. The main argument in this thesis is that profound understanding of the advanced technology of laser-arc hybrid welding will help improve the productivity of welding in industrial applications. Based on a review of the current knowledge base, important areas for further research are also identified. This thesis consists of two parts. The first part introduces the research topic and discusses laser–arc hybrid welding by characterizing its mechanism and most important variables. The second part comprises four research papers elaborating on the performance of laser– arc hybrid welding in the joining of metals. The study uses quantitative and qualitative research methods which include in-depth, interpretive analyses of results from a number of research groups. In the interpretive analysis, the emphasis is placed on the relevance and usefulness of the investigative results drawn from other research publications. The results of this study contribute to research on laser–arc hybrid welding by increasing understanding of how old and new perspectives on laser–arc hybrid welding are evidenced in industry. The research methodology applied permits continued exploration of how laser–arc hybrid welding and various process factors influence the overall quality of the weld. Thestudy provides a good foundation for future research, creates improved awareness of the laser–arc hybrid welding process, and assists the metal industry to maximize welding productivity.

Pinta-aktiiviaineiden vaikutus kuitulinjan toimintaan

Työssä tutkittiin kahden eri pinta-aktiiviaineen A ja B käytön vaikutusta kahdella eri kuitulinjalla. Molempien pinta-aktiiviaineiden pääfunktiona oli vaikuttaa nes-teen pintajännitykseen, jolloin nesteen tunkeutumisnopeus kuitumatriisiin ja kui-tujen huokosiin paranee. Lisäksi pinta-aktiiviaineilla A ja B oli kyky stabiloida nesteeseen liuenneita uuteainekomponentteja, jolloin uudelleensaostumisen riski pienenee. Koeajoilla pyrittiin vaikuttamaan happidelignifiointivaiheen uuteainetasoihin, alkali- ja happiannoksiin sekä kappareduktioon. Lisäksi tarkasteltiin annostelun vaikutusta kuitulinjan pesurien toimintaan, uuteainetasojen kehittymiseen koko kuitulinjalla sekä valkaisun kemikaalikulutukseen. Työssä kokeiltiin myös pinta-aktiiviaineen B vaikutusta EOP-vaiheen uuteainetasoon. Työn kirjallisuusosassa perehdyttiin puun uuteaineisiin ja niiden käyttäytymiseen kuitulinjalla, pinta-aktiiviaineisiin, pesun teoriaan sekä kuitulinjan kemikaaliannosteluihin vaikuttaviin tekijöihin. Molemmissa koeajoissa pinta-aktiiviaineet A ja B annosteltiin massan joukkoon juuri ennen happivaihetta. EOP-vaiheeseen pinta-aktiiviaine B annostelu tehtiin D0-vaiheen pesurin jälkeiseen massaan. Asetoniuutemääritykset tehtiin massasta ennen happivaihetta, happivaiheen jälkeen ja valkaistulle massalle sekä pinta-aktiiviaine B koeajon yhteydessä EOP-vaiheen jälkeen. Pinta-aktiiviaineiden käytöllä havaittiin olevan positiivinen vaikutus kuitulinjan asetoniuutetasojen kehittymisessä. Verrattuna referenssijaksoon, oli happivaiheen alkali- ja happiannokset pienemmät pinta-aktiiviaineiden käytön aikana ilman, että saavutettu kappareduktio heikkeni. Pesurien toiminnan kannalta pinta-aktiiviaineiden käytöllä oli myönteisiä vaikutuksia pesutehokkuuden ja pesun ta-saisuuden kannalta. Lisäksi havaittiin valkaisussa merkittävä muutos D0- ja D1-vaiheiden klooridioksiveden käytössä ja EOP-vaiheen alkaliannoksessa.

Spectroscopic monitoring during laser welding of aluminium alloy

The mechanical properties of aluminium alloys are strongly influenced by the alloying elements and their concentration. In the case of aluminium alloy EN AW-6060 the main alloying elements are magnesium and silicon. The first goal of this thesis was to determine stability, repeatability and sensitivity as figures of merit of the in-situ melt identification technique. In this study the emissions from the laser welding process were monitored with a spectrometer. With the information produced by the spectrometer, quantitative analysis was conducted to determine the figures of merit. The quantitative analysis concentrated on magnesium and aluminium emissions and their relation. The results showed that the stability of absolute intensities was low, but the normalized magnesium emissions were quite stable. The repeatability of monitoring magnesium emissions was high (about 90 %). Sensitivity of the in-situ melt identification technique was also high. As small as 0.5 % change in magnesium content was detected by the spectrometer. The second goal of this study was to determine the loss of mass during deep penetration laser welding. The amount of magnesium in the material was measured before and after laser welding to determine the loss of magnesium. This study was conducted for aluminium alloy with nominal magnesium content of 0-10 % and for standard material EN AW-6060 that was welded with filler wire AlMg5. It was found that while the magnesium concentration in the material changed, the loss of magnesium remained fairly even. Also by feeding filler wire, the behaviour was similar. Thirdly, the reason why silicon had not been detected in the emission spectrum needed to be explained. Literature research showed that the amount of energy required for silicon to excite is considerably higher compared to magnesium. The energy input in the used welding process is insufficient to excite the silicon atoms.

Myöhäinen pakkasvarastoinnin päättäminen lisää kuusentaimien pakkasvaurioriskiä syksyllä

Seloste artikkelista: Hänninen, H., Luoranen, J., Rikala, R. and Smolander, H. 2009. Late termination of freezer storage increases the risk of autumn frost damage to Norway spruce seedlings. Silva Fennica 43 (5) : 817–830.

Wood as a model material for medical biomaterials. In vivo and in vitro studies with bone and Betula pubescens Ehrh

Novel biomaterials are needed to fill the demand of tailored bone substitutes required by an ever‐expanding array of surgical procedures and techniques. Wood, a natural fiber composite, modified with heat treatment to alter its composition, may provide a novel approach to the further development of hierarchically structured biomaterials. The suitability of wood as a model biomaterial as well as the effects of heat treatment on the osteoconductivity of wood was studied by placing untreated and heat‐treated (at 220 C , 200 degrees and 140 degrees for 2 h) birch implants (size 4 x 7mm) into drill cavities in the distal femur of rabbits. The follow‐up period was 4, 8 and 20 weeks in all in vivo experiments. The flexural properties of wood as well as dimensional changes and hydroxyl apatite formation on the surface of wood (untreated, 140 degrees C and 200 degrees C heat‐treated wood) were tested using 3‐point bending and compression tests and immersion in simulated body fluid. The effect of premeasurement grinding and the effect of heat treatment on the surface roughness and contour of wood were tested with contact stylus and non‐contact profilometry. The effects of heat treatment of wood on its interactions with biological fluids was assessed using two different test media and real human blood in liquid penetration tests. The results of the in vivo experiments showed implanted wood to be well tolerated, with no implants rejected due to foreign body reactions. Heat treatment had significant effects on the biocompatibility of wood, allowing host bone to grow into tight contact with the implant, with occasional bone ingrowth into the channels of the wood implant. The results of the liquid immersion experiments showed hydroxyl apatite formation only in the most extensively heat‐treated wood specimens, which supported the results of the in vivo experiments. Parallel conclusions could be drawn based on the results of the liquid penetration test where human blood had the most favorable interaction with the most extensively heat‐treated wood of the compared materials (untreated, 140 degrees C and 200 degrees C heat‐treated wood). The increasing biocompatibility was inferred to result mainly from changes in the chemical composition of wood induced by the heat treatment, namely the altered arrangement and concentrations of functional chemical groups. However, the influence of microscopic changes in the cell walls, surface roughness and contour cannot be totally excluded. The heat treatment was hypothesized to produce a functional change in the liquid distribution within wood, which could have biological relevance. It was concluded that the highly evolved hierarchical anatomy of wood could yield information for the future development of bulk bone substitutes according to the ideology of bioinspiration. Furthermore, the results of the biomechanical tests established that heat treatment alters various biologically relevant mechanical properties of wood, thus expanding the possibilities of wood as a model material, which could include e.g. scaffold applications, bulk bone applications and serving as a tool for both mechanical testing and for further development of synthetic fiber reinforced composites.

CFD Modelling of Direct Contact Condensation in Suppression Pools by Applying Condensation Models of Separated Flow

The condensation rate has to be high in the safety pressure suppression pool systems of Boiling Water Reactors (BWR) in order to fulfill their safety function. The phenomena due to such a high direct contact condensation (DCC) rate turn out to be very challenging to be analysed either with experiments or numerical simulations. In this thesis, the suppression pool experiments carried out in the POOLEX facility of Lappeenranta University of Technology were simulated. Two different condensation modes were modelled by using the 2-phase CFD codes NEPTUNE CFD and TransAT. The DCC models applied were the typical ones to be used for separated flows in channels, and their applicability to the rapidly condensing flow in the condensation pool context had not been tested earlier. A low Reynolds number case was the first to be simulated. The POOLEX experiment STB-31 was operated near the conditions between the ’quasi-steady oscillatory interface condensation’ mode and the ’condensation within the blowdown pipe’ mode. The condensation models of Lakehal et al. and Coste & Lavi´eville predicted the condensation rate quite accurately, while the other tested ones overestimated it. It was possible to get the direct phase change solution to settle near to the measured values, but a very high resolution of calculation grid was needed. Secondly, a high Reynolds number case corresponding to the ’chugging’ mode was simulated. The POOLEX experiment STB-28 was chosen, because various standard and highspeed video samples of bubbles were recorded during it. In order to extract numerical information from the video material, a pattern recognition procedure was programmed. The bubble size distributions and the frequencies of chugging were calculated with this procedure. With the statistical data of the bubble sizes and temporal data of the bubble/jet appearance, it was possible to compare the condensation rates between the experiment and the CFD simulations. In the chugging simulations, a spherically curvilinear calculation grid at the blowdown pipe exit improved the convergence and decreased the required cell count. The compressible flow solver with complete steam-tables was beneficial for the numerical success of the simulations. The Hughes-Duffey model and, to some extent, the Coste & Lavi´eville model produced realistic chugging behavior. The initial level of the steam/water interface was an important factor to determine the initiation of the chugging. If the interface was initialized with a water level high enough inside the blowdown pipe, the vigorous penetration of a water plug into the pool created a turbulent wake which invoked the chugging that was self-sustaining. A 3D simulation with a suitable DCC model produced qualitatively very realistic shapes of the chugging bubbles and jets. The comparative FFT analysis of the bubble size data and the pool bottom pressure data gave useful information to distinguish the eigenmodes of chugging, bubbling, and pool structure oscillations.

Welding development of crane main girder

Konecranes Corporation manufactures huge steel structures in 16 factories worldwide, in which the environment and quality varies. The company has a desire to achieve the same weld quality in each factory, regardless of the manufacturing place. The main subject of this master’s thesis was to develop the present box girder crane welding process, submerged arc welding and especially the fillet welding. Throughput time and manufacturing costs can be decreased by welding the full penetration fillet weld without a bevel, changing present groove types for more appropriate ones and by achieving the desired weld quality on the first time. Welding experiments of longitudinal fillet welding were made according to the present challenges, which the manufacturing process is facing. In longitudinal fillet welding tests the main focus was to achieve full penetration fillet weld for 6, 8 and 10 millimeters thick web plates with single and twin wire submerged arc welding. Full penetration was achieved with all the material thicknesses, both with single and twin wire submerged arc welding processes. The main problem concerning the weld was undercutting and shape of the weld bead. The question about insufficiency of presently used power sources with twin wire was risen up during testing, due to the thicknesses that require high welding current. Bigger power source is required when box girders are welded nonstop, if twin wire is used. For single wire process the penetration was achieved with significantly less amperage than with twin wire.

Kertomaa Suomen viime sodasta

Kirja-arvio

Applications and Benefits of Adaptive Pulsed GMAW

In ship and offshore terminal construction, welded cross sections are thick and the number of welds very high. Consequently, there are two aspects of great importance; cost and heat input. Reduction in the welding operation time decreases the costs of the work force and avoids excessive heat, preventing distortion and other weld defects. The need to increase productivity while using a single wire in the GMAW process has led to the use of a high current and voltage to improve the melting rate. Unfortunately, this also increases the heat input. Innovative GMAW processes, mostly implemented for sheet plate sections, have shown significant reduction in heat input (Q), low distortion and increase in welding speed. The aim of this study is to investigate adaptive pulsed GMAW processes and assess relevant applications in the high power range, considering possible benefits when welding thicker sections and high yield strength steel. The study experimentally tests the usability of adaptive welding processes and evaluates their effects on weld properties, penetration and shapes of the weld bead.The study first briefly reviews adaptive GMAW to evaluate different approaches and their applications and to identify benefits in adaptive pulsed. Experiments are then performed using Synergic Pulsed GMAW, WiseFusionTM and Synergic GMAW processes to weld a T-joint in a horizontal position (PB). The air gap between the parts ranges from 0 to 2.5 mm. The base materials are structural steel grade S355MC and filler material G3Si1. The experiment investigates heat input, mechanical properties and microstructure of the welded joint. Analysis of the literature reveals that different approaches have been suggested using advanced digital power sources with accurate waveform, current, voltage, and feedback control. In addition, studies have clearly indicated the efficiency of lower energy welding processes. Interest in the high power range is growing and a number of different approaches have been suggested. The welding experiments in this study reveal a significant reduction of heat input and a weld microstructure with the presence of acicular ferrite (AF) beneficial for resistance to crack propagation. The WiseFusion bead had higher dilution, due to the weld bead shape, and low defects. Adaptive pulse GMAW processes can be a favoured choice when welding structures with many welded joints. The total heat reduction mitigates residual stresses and the bead shape allows a higher amperage limit. The stability of the arc during the process is virtually spatter free and allows an increase in welding speed.

FAT-luokkien määritys hitsatuille levyliitoksille käyttämällä lineaarisen murtumismekaniikan särönkasvun simulointia

Työssä tutkittiin hitsattujen levyliitosten väsymiskestävyyden mitoitusarvoja. Hitsien väsymiskestävyyden mitoitusarvot määritettiin lineaarista murtumismekaniikkaa soveltavalla 2D FEM-laskentaohjelmalla. Murtumismekaanisen laskennan tuloksista määriteltiin, eri liitosgeometrioiden ja kuormitustyyppien mukaisia, nimellisen jännityksen väsymismitoitusmenetelmää vastaavia FAT-luokkia, joissa on huomioitu rakenteellinen jännitys hitsiä vastaan kohtisuorassa suunnassa. Tutkittujen liitosten geometriat olivat pääsääntöisesti poikkeavia mitoitusstandardien ja ohjeiden sisältämistä taulukkotapauksista. Laskennassa otettiin huomioon hitsien liittymiskulma perusaineeseen, rajaviivan pyöristykset ja vajaa hitsautumissyvyys. Kuormitustyyppien vaihtelua tutkittiin rakenteellisen jännityksen taivutusosuuden muutoksilla ja kuormaa kantavien X-liitosten risteävien kuormituksien suhteellisilla suuruuksilla. Väsymiskestävyydet määritettiin kuormituskohtaisille kalvo- ja taivutusjännityksille sekä näiden jännitysjakaumien keskiarvoille. Työssä saatuja FAT-luokkia voidaan hyödyntää vastaavien geometrioiden ja kuormitusten yhteydessä, sekä interpoloimalla myös tuloksien väliarvoissa. Työssä käytetyillä menetelmillä voidaan parantaa nimellisen jännityksen mitoitusmenetelmän tarkkuutta ja laajentaa sitä koskemaan myös taulukkotapausten ulkopuolisia liitoksia. Työn tuloksissa on esitetty FAT-luokkia T-, X- ja päittäisliitoksille ja näiden eri kuormitusyhdistelmille.

Liquid transportation and distribution during (re)wetting : impact on coated papers in printing

In many industrial applications, such as the printing and coatings industry, wetting of porous materials by liquids includes not only imbibition and permeation into the bulk but also surface spreading and evaporation. By understanding these phenomena, valuable information can be obtained for improved process control, runnability and printability, in which liquid penetration and subsequent drying play important quality and economic roles. Knowledge of the position of the wetting front and the distribution/degree of pore filling within the structure is crucial in describing the transport phenomena involved. Although exemplifying paper as a porous medium in this work, the generalisation to dynamic liquid transfer onto a surface, including permeation and imbibition into porous media, is of importance to many industrial and naturally occurring environmental processes. This thesis explains the phenomena in the field of heatset web offset printing but the content and the analyses are applicable in many other printing methods and also other technologies where water/moisture monitoring is crucial in order to have a stable process and achieve high quality end products. The use of near-infrared technology to study the water and moisture response of porous pigmented structures is presented. The use of sensitive surface chemical and structural analysis, as well as the internal structure investigation of a porous structure, to inspect liquid wetting and distribution, complements the information obtained by spectroscopic techniques. Strong emphasis has been put on the scale of measurement, to filter irrelevant information and to understand the relationship between interactions involved. The near-infrared spectroscopic technique, presented here, samples directly the changes in signal absorbance and its variation in the process at multiple locations in a print production line. The in-line non-contact measurements are facilitated by using several diffuse reflectance probes, giving the absolute water/moisture content from a defined position in the dynamic process in real-time. The nearinfrared measurement data illustrate the changes in moisture content as the paper is passing through the printing nips and dryer, respectively, and the analysis of the mechanisms involved highlight the roles of the contacting surfaces and the relative liquid carrier properties of both non-image and printed image areas. The thesis includes laboratory studies on wetting of porous media in the form of coated paper and compressed pigment tablets by mono-, dual-, and multi-component liquids, and paper water/moisture content analysis in both offline and online conditions, thus also enabling direct sampling of temporal water/moisture profiles from multiple locations. One main focus in this thesis was to establish a measurement system which is able to monitor rapid changes in moisture content of paper. The study suggests that near-infrared diffuse reflectance spectroscopy can be used as a moisture sensitive system and to provide accurate online qualitative indicators, but, also, when accurately calibrated, can provide quantification of water/moisture levels, its distribution and dynamic liquid transfer. Due to the high sensitivity, samples can be measured with excellent reproducibility and good signal to noise ratio. Another focus of this thesis was on the evolution of the moisture content, i.e. changes in moisture content referred to (re)wetting, and liquid distribution during printing of coated paper. The study confirmed different wetting phases together with the factors affecting each phase both for a single droplet and a liquid film applied on a porous substrate. For a single droplet, initial capillary driven imbibition is followed by equilibrium pore filling and liquid retreat by evaporation. In the case of a liquid film applied on paper, the controlling factors defining the transportation were concluded to be the applied liquid volume in relation to surface roughness, capillarity and permeability of the coating giving the liquid uptake capacity. The printing trials confirmed moisture gradients in the printed sheet depending on process parameters such as speed, fountain solution dosage and drying conditions as well as the printed layout itself. Uneven moisture distribution in the printed sheet was identified to be one of the sources for waving appearance and the magnitude of waving was influenced by the drying conditions.

Puomiankkurin uudelleensuunnittelu ja valmistus

Tämän diplomityön tavoitteena on ollut suunnitella uusi öljyntorjunnassa käytettävä puomiankkuri. Nykyisin käytössä olevat ankkurit ovat painavia, paljon tilaa vieviä, jäykkiä rakenteeltaan ja hankalia käyttää. Työn tavoitteena on ollut suunnitella rakenne, jossa muotoilun avulla pyritään korvaamaan ankkurin painoa ja saavuttaa hyvä tunkeutuminen eri pohjalaaduissa. Ankkurin suunnitteluun kuuluu merkittävänä osana materiaalinvalintaprosessi, jonka perusteella materiaaliksi valittiin kulutusteräs. Kulutusteräksen korkea lujuus ja hyvä kulumiskestävyys mahdollistavat ohuemman materiaalin käytön rakenteessa, jonka seurauksena rakenteen painoa saatiin vähennettyä merkittävästi. Ankkurin rakenteen suunnittelussa käytettiin hyväksi nykyisiä ankkurin rakenteita, joiden pohjalta hahmoteltiin eri variaatioita ankkureista. Suunnittelutyössä käytettiin hyväksi tyypillisiä ankkurirakenteita hyvien puolien kannalta, joita pyrittiin toteuttamaan uudessa ankkuri- rakenteessa. Ankkurin suunnittelu toteutettiin järjestelmällisen suunnittelun avulla, jossa ensin laadittiin ankkurille vaatimuslista. Tämän jälkeen laadittiin ankkurille toimintorakenne ja jakaminen osatoimintoihin. Ankkurin rakenteista toteutettiin kaksi eri versiota: sisävesillä ja merialueilla käytettävät ankkurit, joille laadittiin mitoitus. Työssä suunnitellun terävän tunkeutumisosan ja optimaalisen tunkeutumiskulman avulla ankkureiden painoa saatiin huomattavasti alhaisemmaksi, jonka seurauksena ankkurille saatiin kevyempi rakenne ja materiaalikustannukset pienenivät merkittävästi. Uusien ankkurien rakenne on pienemmän koon ja painon ansiosta käyttäjäystävällisempi.