Radiative Heat Transfer in Boiler Furnaces

Better models are needed for radiative heat transfer in boiler furnaces. If the process is known better, combustion in the furnace can be optimized to produce low emissions. It makes the process to be environmental friendly. Furthermore, if there is a better model of the furnace it can more fully explain what is happening inside the furnace. Using of the model one can quickly and easily analyze how it operates with bio fuels, moist fuels or difficult fuels and improve the operation. Models helps with better estimation of furnace dimensions and result in more accurate understanding of operation. Key component lacking in these models is radiative heat transfer in particle laden gases. If there are no particles than radiative heat transfer can be calculated approximately. There are two problems with current models when used with flow modeling. The first one is a need to account for a particle laden gas and the second one is an absence of a fast algorithm. Fast calculation is needed if radiative heat transfer calculation is done for a large CDF model. Computations slow down if time is required for calculating radiative properties over and over again. This thesis presents a band model for radiative heat transfer in boiler furnaces. Advantage is a quickness of calculation and account of particles in the process.

The use of future-oriented knowledge in regional innovation processes: Research on knowledge generation, transfer and conversion

The importance of the regional level in research has risen in the last few decades and a vast literature in the fields of, for instance, evolutionary and institutional economics, network theories, innovations and learning systems, as well as sociology, has focused on regional level questions. Recently the policy makers and regional actors have also began to pay increasing attention to the knowledge economy and its needs, in general, and the connectivity and support structures of regional clusters in particular. Nowadays knowledge is generally considered as the most important source of competitive advantage, but even the most specialised forms of knowledge are becoming a short-lived resource for example due to the accelerating pace of technological change. This emphasizes the need of foresight activities in national, regional and organizational levels and the integration of foresight and innovation activities. In regional setting this development sets great challenges especially in those regions having no university and thus usually very limited resources for research activities. Also the research problem of this dissertation is related to the need to better incorporate the information produced by foresight process to facilitate and to be used in regional practice-based innovation processes. This dissertation is a constructive case study the case being Lahti region and a network facilitating innovation policy adopted in that region. Dissertation consists of a summary and five articles and during the research process a construct or a conceptual model for solving this real life problem has been developed. It is also being implemented as part of the network facilitating innovation policy in the Lahti region.

Coolant Flow and Heat Transfer in Pebble-Bed Reactor Core

This thesis gathers knowledge about ongoing high-temperature reactor projects around the world. Methods for calculating coolant flow and heat transfer inside a pebble-bed reactor core are also developed. The thesis begins with the introduction of high-temperature reactors including the current state of the technology. Process heat applications that could use the heat from a high-temperature reactor are also introduced. A suitable reactor design with data available in literature is selected for the calculation part of the thesis. Commercial computational fluid dynamics software Fluent is used for the calculations. The pebble-bed is approximated as a packed-bed, which causes sink terms to the momentum equations of the gas flowing through it. A position dependent value is used for the packing fraction. Two different models are used to calculate heat transfer. First a local thermal equilibrium is assumed between the gas and solid phases and a single energy equation is used. In the second approach, separate energy equations are used for the phases. Information about steady state flow behavior, pressure loss, and temperature distribution in the core is obtained as results of the calculations. The effect of inlet mass flow rate to pressure loss is also investigated. Data found in literature and the results correspond each other quite well, considered the amount of simplifications in the calculations. The models developed in this thesis can be used to solve coolant flow and heat transfer in a pebble-bed reactor, although additional development and model validation is needed for better accuracy and reliability.

Modeling reaction kinetics and mass transfer in ozonation in water solutions

This dissertation is based on four articles dealing with modeling of ozonation. The literature part of this considers some models for hydrodynamics in bubble column simulation. A literature review of methods for obtaining mass transfer coefficients is presented. The methods presented to obtain mass transfer are general models and can be applied to any gas-liquid system. Ozonation reaction models and methods for obtaining stoichiometric coefficients and reaction rate coefficients for ozonation reactions are discussed in the final section of the literature part. In the first article, ozone gas-liquid mass transfer into water in a bubble column was investigated for different pH values. A more general method for estimation of mass transfer and Henry’s coefficient was developed from the Beltrán method. The ozone volumetric mass transfer coefficient and the Henry’s coefficient were determined simultaneously by parameter estimation using a nonlinear optimization method. A minor dependence of the Henry’s law constant on pH was detected at the pH range 4 - 9. In the second article, a new method using the axial dispersion model for estimation of ozone self-decomposition kinetics in a semi-batch bubble column reactor was developed. The reaction rate coefficients for literature equations of ozone decomposition and the gas phase dispersion coefficient were estimated and compared with the literature data. The reaction order in the pH range 7-10 with respect to ozone 1.12 and 0.51 the hydroxyl ion were obtained, which is in good agreement with literature. The model parameters were determined by parameter estimation using a nonlinear optimization method. Sensitivity analysis was conducted using object function method to obtain information about the reliability and identifiability of the estimated parameters. In the third article, the reaction rate coefficients and the stoichiometric coefficients in the reaction of ozone with the model component p-nitrophenol were estimated at low pH of water using nonlinear optimization. A novel method for estimation of multireaction model parameters in ozonation was developed. In this method the concentration of unknown intermediate compounds is presented as a residual COD (chemical oxygen demand) calculated from the measured COD and the theoretical COD for the known species. The decomposition rate of p-nitrophenol on the pathway producing hydroquinone was found to be about two times faster than the p-nitrophenol decomposition rate on the pathway producing 4- nitrocatechol. In the fourth article, the reaction kinetics of p-nitrophenol ozonation was studied in a bubble column at pH 2. Using the new reaction kinetic model presented in the previous article, the reaction kinetic parameters, rate coefficients, and stoichiometric coefficients as well as the mass transfer coefficient were estimated with nonlinear estimation. The decomposition rate of pnitrophenol was found to be equal both on the pathway producing hydroquinone and on the path way producing 4-nitrocathecol. Comparison of the rate coefficients with the case at initial pH 5 indicates that the p-nitrophenol degradation producing 4- nitrocathecol is more selective towards molecular ozone than the reaction producing hydroquinone. The identifiability and reliability of the estimated parameters were analyzed with the Marcov chain Monte Carlo (MCMC) method. @All rights reserved. No part of the publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior permission of the author.

Role of Membrane Transporters, P-Glycoprotein and Mrp1, in The Placental Transfer of Drugs With Special Reference to Saquinavir and Quetiapine

Drug transporting membrane proteins are expressed in various human tissues and blood-tissue barriers, regulating the transfer of drugs, toxins and endogenous compounds into or out of the cells. Various in vitro and animal experiments suggest that P-glycoprotein (P-gp) forms a functional barrier between maternal and fetal blood circulation in the placenta thereby protecting the fetus from exposure to xenobiotics during pregnancy. The multidrug resistance-associated protein 1 (MRP1) is a relatively less studied transporter protein in the human placenta. The aim of this study series was to study the role of placental transporters, apical P-gp and basal MRP1, using saquinavir as a probe drug, and to study transfer of quetiapine and the role of P-gp in its transfer in the dually perfused human placenta/cotyledon. Furthermore, two ABCB1 (encoding P-gp) polymorphisms (c.3435C>T, p.Ile1145Ile and c.2677G>T/A, p.Ala893Ser/Thr) were studied to determine their impact on P-gp protein expression level and on the transfer of the study drugs. Also, the influence of the P-gp protein expression level on the transfer of the study drugs was addressed. Because P-gp and MRP1 are ATP-dependent drug-efflux pumps, it was studied whether exogenous ATP is needed for the function of ATP-dependent transporter in the present experimental model. The present results indicated that the addition of exogenous ATP was not necessary for transporter function in the perfused human placental cotyledon. Saquinavir and quetiapine were both found to cross the human placenta; transplacental transfer (TPTAUC %) for saquinavir was <0.5% and for quetiapine 3.7%. Pharmacologic blocking of P-gp led to disruption of the blood-placental barrier (BPB) and increased the placental transfer of P-gp substrate, saquinavir, into the fetal circulation by 6- to 8-fold. In reversed perfusions P-gp, MRP1 and possibly OATP2B1 had a negligible role in the fetal-to-maternal transfer of saquinavir. The TPTAUC % of saquinavir was about 100-fold greater from the fetal side to the maternal side compared with the maternal-to-fetal transfer. P-gp activity is not likely to modify the placental transfer of quetiapine. Higher P-gp protein expression levels were associated with the variant allele 3435T, but no correlation was found between the TPTAUC % of saquinavir and placental P-gp protein expression. The present results indicate that P-gp activity drastically affects the fetal exposure to saquinavir, and suggest that pharmacological blockade of the P-gp activity during pregnancy may pose an increased risk for adverse fetal outcome. The blockade of P-gp activity could be used in purpose to obtain higher drug concentration to the fetal side, for example, in prevention (to decrease virus transfer to fetal side) or in treating sick fetus.

Cost Optimisation of Mobile Advertising Client Data Transfer

Data traffic caused by mobile advertising client software when it is communicating with the network server can be a pain point for many application developers who are considering advertising-funded application distribution, since the cost of the data transfer might scare their users away from using the applications. For the thesis project, a simulation environment was built to mimic the real client-server solution for measuring the data transfer over varying types of connections with different usage scenarios. For optimising data transfer, a few general-purpose compressors and XML-specific compressors were tried for compressing the XML data, and a few protocol optimisations were implemented. For optimising the cost, cache usage was improved and pre-loading was enhanced to use free connections to load the data. The data traffic structure and the various optimisations were analysed, and it was found that the cache usage and pre-loading should be enhanced and that the protocol should be changed, with report aggregation and compression using WBXML or gzip.

Heat Transfer in Plate Heat Exchangers

This study illustrates the different types of plate heat exchangers that are commonly used in various domestic and industrial applications. The main purpose of this paper was to devise a methodology that is capable of calculating optimum number of plates in the design of a plate heat exchanger. To obtain the appropriate number of plates, typically several iterations must be made before a final acceptable design is completed, since plate amount depends on many factors such as, flow velocities, physical properties of the streams, flow channel geometry, allowable pressure drop, plate dimensions, and the gap between the plates. The methodology presented here can be used as a general guide for designing a plate heat exchanger. To investigate the effects of relevant parameters on the thermal-hydraulic design of a plate heat exchanger, several experiments were carried out for single-phase and counter flow arrangement with two brazed plate heat exchangers by varying the flow rates and the inlet temperatures of the fluid streams. The actual heat transfer coefficients obtained based on the experiment were nearly close to the calculated values and to improve the design, a correction factor was introduced. Besides, the effect of flow channel velocity on the pressure drop inside the unit is presented.

Sustainability of palm oil production and opportunities for Finnish technology and know-how transfer

The global demand for palm oil is growing, thus prompting an increase in the global production particularly in Malaysia and Indonesia. Such increasing demand for palm oil is due to palm oil’s relatively cheap price and versatile advantage both in edible and non-edible applications. Along with the increasing demand for palm oil, particularly for the production of biofuel, is a heated debate on its sustainability. Ecological degradation, climate change and social issues are among the main sustainability issues pressing the whole palm oil industry today. Clean Development Mechanism (CDM) projects fulfilling the imperatives of the Kyoto Protocol are starting to gain momentum in Malaysia as reflected by the increasing registration of CDM projects in the palm oil mills. Most CDM projects in palm oil mills are on waste-to-energy, cocomposting, and methane recovery with the latter being the most common. The study on greenhouse gases (GHG) in the milling process points that biogas collection and energy utilisation has the greatest positive effect on GHG balance. On the other hand, empty fruit bunches (EFB) end-use as energy and high energy efficiency of the mill have the least effect on GHG balance of the mill. The range of direct GHG emissions from the palm oil mill is from 2.5 to 27 gCO2e/MJCPO, while the range of GHG emissions with all indirect and avoided emissions included is from -9 to 29 gCO2e/MJCPO. Comparing this GHG balance result with that of the EU RES-Directive suggests a further check on the values and emissions consideration of the latter.

Heat transfer in superheaters of the bubbling fluidized bed boiler conversions

It is often reasonable to convert old boiler to bubbling fluidized bed boiler instead of building a new one. Converted boiler consists of old and new heat surfaces which must be fitted to operate together. Prediction of heat transfer in not so ideal conditions sets challenges for designers. Two converted boilers situated in Poland were studied on the grounds of acceptance tests and further studies. Calculation of boiler process was performed with boiler design program. Main interest was heat transfer in superheaters and factors affecting it. Theory for heat transfer is presented according to information found from literature. Results obtained from experimental studies and calculations have been compared. With correct definitions calculated parameters corresponded well to measured data at boiler maximum design load. However overload situations revealed to be difficult to model at least without considering changes in the combustion process which requires readjustments to the design program input values.

Lanthanide Chelates as Donors in Fluorescence Resonance Energy Transfer: Exciting Prospects for Bioaffinity Assay Detection

Fluorescence resonance energy transfer (FRET) is a non-radiative energy transfer from a fluorescent donor molecule to an appropriate acceptor molecule and a commonly used technique to develop homogeneous assays. If the emission spectrum of the donor overlaps with the excitation spectrum of the acceptor, FRET might occur. As a consequence, the emission of the donor is decreased and the emission of the acceptor (if fluorescent) increased. Furthermore, the distance between the donor and the acceptor needs to be short enough, commonly 10-100 Å. Typically, the close proximity between the donor and the acceptor is achieved via bioaffinity interactions e.g. antibody binding antigen. Large variety of donors and acceptors exist. The selection of the donor/acceptor pair should be done not only based on the requirements of FRET but also the performance expectancies and the objectives of the application should be considered. In this study, the exceptional fluorescence properties of the lanthanide chelates were employed to develop two novel homogeneous immunoassays: a non-competitive hapten (estradiol) assay based on a single binder and a dual-parametric total and free PSA assay. In addition, the quenching efficiencies and energy transfer properties of various donor/acceptor pairs were studied. The applied donors were either europium(III) or terbium(III) chelates; whereas several organic dyes (both fluorescent and quenchers) acted as acceptors. First, it was shown that if the interaction between the donor/acceptor complexes is of high quality (e.g. biotin-streptavidin) the fluorescence of the europium(III) chelate could be quenched rather efficiently. Furthermore, the quenching based homogeneous non-competitive assay for estradiol had significantly better sensitivity (~67 times) than a corresponding homogeneous competitive assay using the same assay components. Second, if the acceptors were chosen to emit at the emission minima of the terbium(III) chelate, several acceptor emissions could be measured simultaneously without significant cross-talk from other acceptors. Based on these results, the appropriate acceptors were chosen for the dual-parameter assay. The developed homogeneous dual-parameter assay was able to measure both total and free PSA simultaneously using a simple mix and measure protocol. Correlation of this assay to a heterogeneous single parameter assay was excellent (above 0.99 for both) when spiked human plasma samples were used. However, due to the interference of the sample material, the obtained concentrations were slightly lower with the homogeneous than the heterogeneous assay, especially for the free PSA. To conclude, in this work two novel immunoassay principles were developed, which both are adaptable to other analytes. However, the hapten assay requires a rather good antibody with low dissociation rate and high affinity; whereas the dual-parameter assay principle is applicable whenever two immunometric complexes can form simultaneously, provided that the requirements of FRET are fulfilled.

Improving Evaluation and Development Capability in Verification and Validation

Validation and verification operations encounter various challenges in product development process. Requirements for increasing the development cycle pace set new requests for component development process. Verification and validation usually represent the largest activities, up to 40 50 % of R&D resources utilized. This research studies validation and verification as part of case company's component development process. The target is to define framework that can be used in improvement of the validation and verification capability evaluation and development in display module development projects. Validation and verification definition and background is studied in this research. Additionally, theories such as project management, system, organisational learning and causality is studied. Framework and key findings of this research are presented. Feedback system according of the framework is defined and implemented to the case company. This research is divided to the theory and empirical parts. Theory part is conducted in literature review. Empirical part is done in case study. Constructive methode and design research methode are used in this research A framework for capability evaluation and development was defined and developed as result of this research. Key findings of this study were that double loop learning approach with validation and verification V+ model enables defining a feedback reporting solution. Additional results, some minor changes in validation and verification process were proposed. There are a few concerns expressed on the results on validity and reliability of this study. The most important one was the selected research method and the selected model itself. The final state can be normative, the researcher may set study results before the actual study and in the initial state, the researcher may describe expectations for the study. Finally reliability of this study, and validity of this work are studied.

A three dimensional study of heat transfer in a supercritical circulating fluidized bed combustor

From the boiler design point of view, it is imperative to know and understand the operation of the boiler. Since comprehensive measurement of a large furnace is impossible, the furnace can be modeled in order to study its behavior and phenomena. This requires the used model to be validated to correspond with the physical furnace behavior. In this thesis, a three dimensional furnace model is validated to match a bituminous coal utilizing, supercritical once-through circulating fluidized bed combustor based on measurement data. The validated model is used for analyzing the furnace heat transfer. Other heat transfer analysis methods are energy balance method based on tube surface temperature measurements and a method based on measured temperature difference between the tube crest and the fin. The latter method was developed in the thesis using Fluent-software. In the theory part, literature is reviewed and the fundamental aspects of circulating fluidized bed are discussed. These aspects are solid particle behavior in fluidization known as hydrodynamics, behavior of fuel and combustion and heat transfer. Fundamental aspects of modeling are also presented.

Supplier relationship management capability in the firm's global integration

Organizing is a general problem for global firms. Firms are seeking a balance between responsiveness at the local level and efficiency through worldwide integration. In this, supply management is the focal point where external commercial supply market relations are connected with the firm's internal functions. Here, effective supplier relationship management (SRM) is essential. Global supply integration processes create new challenges for supply management professionals and new capabilities are required. Previous research has developed several models and tools for managers to manage and categorize different supplier relationship types, but the role of the firm's internal capability of managing supplier relationships in their global integration has been a clearly neglected issue. Hence, the main objective of this dissertation is to clarify how the capability of SRM may influence the firm's global competitiveness. This objective is divided into four research questions aiming to identify the elements of SRM capability, the internal factors of integration, the effect of SRM capability on strategy and how SRM capability is linked with global integration. The dissertation has two parts. The first part presents the theoretical approaches and practical implications from previous research and draws a synthesis on them. The second part comprises four empirical research papers addressing the research questions. Both qualitative and quantitative methods are utilized in this dissertation. The main contribution of this dissertation is that it aggregates the theoretical and conceptual perspectives applied to SRM research. Furthermore, given the lack of valid scales to measure capability, this study aimed to provide a foundation for an SRM capability scale by showing that the construct of SRM capability is formed of five separate elements. Moreover, SRM capability was found to be the enabler in efforts toward value chain integration. Finally, it was found that the effect of capability on global competitiveness is twofold: it reduces conflicts between responsiveness and integration, and it creates efficiency. Thus, by identifying and developing the firm's capabilities it is possible to improve performance, and hence, global competitiveness.

Customer reference marketing in a business to business context

This study focuses on the phenomenon of customer reference marketing in a business tobusiness (B to B) context. Although customer references are generally considered an important marketing and sales tool, the academic literature has paid surprisingly little attention to the phenomenon. The study suggests that customer references could be viewed as important marketing assets for industrial suppliers, and the ability to build, manage and leverage customer reference portfolios systematically constitutes a relevant marketing capability. The role of customer references is examined in the context of the industrial suppliers' shift towards a solution and project orientation and in the light of the on going changes in the project business. Suppliers in several industry sectors are undergoing a change from traditional equipment manufacturing towards project and solution oriented business. It is argued in this thesis that the high complexity, the project oriented nature and the intangible service elements that characterise many contemporary B to B offerings further increase the role of customer references. The study proposes three mechanisms of customer reference marketing: status transfer, validation through testimonials and the demonstration of experience and prior performance. The study was conducted in the context of Finnish B to B process technology and information technology companies. The empirical data comprises 38 interviews with managers of four case companies, 165 customer reference descriptions gathered from six case companies' Web sites, as well as company internal material. The findings from the case studies show that customer references have various external and internal functions that contribute to the growth and performance of B to B firms. Externally, customer references bring status transfer effects from reputable customers, concretise and demonstrate complex solutions, and provide indirect evidence of experience, previous performance, technological functionality and delivered customer value. They can also be leveraged internally to facilitate organisational learning and training, advance offering development, and motivate personnel. Major reference projects create new business opportunities and can be used as a vehicle for strategic change. The findings of the study shed light on the on going changing orientations in the project business environment, increase understanding of the variety of ways in which customer references can be deployed as marketing assets, and provide a framework of the relevant tasks and activities related to building, managing and leveraging a firm's customer reference portfolio. The findings contribute to the industrial marketing research, to the literature on marketing assets and capabilities and to the literature on projects and solutions. The proposed functions and mechanisms of customer reference marketing bring a more thorough and structured understanding about the essence and characteristics of the phenomenon and give a wide ranging view of the role of customer references as marketing assets for B to B firms. The study suggests several managerial implications for industrial suppliers in order to systematise customer reference marketing efforts.

Pankin sisäisen siirtohinnoittelun merkitys ohjauksessa - tapaustutkimus Suomessa toimivasta pankista

Tutkimuksen tavoitteena oli tutkia, miten pankin käyttämä siirtohinnoittelumenetelmä toimii osana pankin ohjausjärjestelmää ja siten tukee organisaation kykyä ja motivaatioita toimia koko pankin kannalta kannattavasti. Ilmiötä tutkittiin tapaustutkimuksena Suomessa toimivassa pankissa. Tutkimuksessa kävi ilmi, että yrityksessä on meneillään siirtohinnoittelumallin muutosprojekti. Projektin tarkoituksena on parantaa kannattavuusseurantaa ja pitkällä tähtäimellä mallin on tarkoitus toimia strategian jalkauttamisen työvälineenä. Tutkimuksessa havaittiin, että siirtohinnoittelumallin keskeisin haaste on saada se sopeutumaan riittävän nopeasti markkinaolosuhteiden muutoksiin siten, että se tukee pankin strategisia tavoitteita. Konttoreiden tulosohjauksessa painotetaan tuloksen lisäksi erilaisia mittaristoja, jotka kuvaavat monipuolisemmin tulosyksikön suoriutumista. Tutkimuksen johtopäätöksenä havaittiin, että siirtohinnoittelumalli voi olla erinomainen johtamisen työkalu, jos se huomioi yrityskohtaiset, taloudelliseen toimintaympäristöön ja yrityksen strategiaan liittyvät erityisvaateet.