Model-based estimation of liquid flows in the blast furnace hearth and taphole

This thesis presents a set of methods and models for estimation of iron and slag flows in the blast furnace hearth and taphole. The main focus was put on predicting taphole flow patterns and estimating the effects of various taphole conditions on the drainage behavior of the blast furnace hearth. All models were based on a general understanding of the typical tap cycle of an industrial blast furnace. Some of the models were evaluated on short-term process data from the reference furnace. A computational fluid dynamics (CFD) model was built and applied to simulate the complicated hearth flows and thus to predict the regions of the hearth exerted to erosion under various operating conditions. Key boundary variables of the CFD model were provided by a simplified drainage model based on the first principles. By examining the evolutions of liquid outflow rates measured from the furnace studied, the drainage model was improved to include the effects of taphole diameter and length. The estimated slag delays showed good agreement with the observed ones. The liquid flows in the taphole were further studied using two different models and the results of both models indicated that it is more likely that separated flow of iron and slag occurs in the taphole when the liquid outflow rates are comparable during tapping. The drainage process was simulated with an integrated model based on an overall balance analysis: The high in-furnace overpressure can compensate for the resistances induced by the liquid flows in the hearth and through the taphole. Finally, a recently developed multiphase CFD model including interfacial forces between immiscible liquids was developed and both the actual iron-slag system and a water-oil system in laboratory scale were simulated. The model was demonstrated to be a useful tool for simulating hearth flows for gaining understanding of the complex phenomena in the drainage of the blast furnace.

Homogeneous assay technologies in drug screening: Quenching Resonance Energy Transfer (QRET) technique

Information gained from the human genome project and improvements in compound synthesizing have increased the number of both therapeutic targets and potential lead compounds. This has evolved a need for better screening techniques to have a capacity to screen number of compound libraries against increasing amount of targets. Radioactivity based assays have been traditionally used in drug screening but the fluorescence based assays have become more popular in high throughput screening (HTS) as they avoid safety and waste problems confronted with radioactivity. In comparison to conventional fluorescence more sensitive detection is obtained with time-resolved luminescence which has increased the popularity of time-resolved fluorescence resonance energy transfer (TR-FRET) based assays. To simplify the current TR-FRET based assay concept the luminometric homogeneous single-label utilizing assay technique, Quenching Resonance Energy Transfer (QRET), was developed. The technique utilizes soluble quencher to quench non-specifically the signal of unbound fraction of lanthanide labeled ligand. One labeling procedure and fewer manipulation steps in the assay concept are saving resources. The QRET technique is suitable for both biochemical and cell-based assays as indicated in four studies:1) ligand screening study of β2 -adrenergic receptor (cell-based), 2) activation study of Gs-/Gi-protein coupled receptors by measuring intracellular concentration of cyclic adenosine monophosphate (cell-based), 3) activation study of G-protein coupled receptors by observing the binding of guanosine-5’-triphosphate (cell membranes), and 4) activation study of small GTP binding protein Ras (biochemical). Signal-to-background ratios were between 2.4 to 10 and coefficient of variation varied from 0.5 to 17% indicating their suitability to HTS use.

Seulonnan erotustehokkuuden määrittäminen - tarkastelussa Reichertin kartioseula

Seulonta on vanha ja teollisuudessa yleisesti käytetty erotusmenetelmä. Huolimat-ta yksinkertaisesta prosessista seulontaa ilmiönä on tutkittu vähän. Prosessin yk-sinkertaisuus on voinut osaltaan vaikuttaa tutkijoiden mielenkiintoon aihetta koh-taan. Tutkimuksen vähyys näkyy etenkin painovoimaiseen seulontaan liittyvän kirjallisuuden vähyytenä. Kirjallisuusosassa käsitellään seulonnan taustaa ja märkä- sekä kuivaseulontaa. Lisäksi määritetään seulontaan vaikuttavat tekijät ja kar-toitetaan seulontaan liittyvää matematiikkaa. Työn kokeellisessa osassa tutkitaan Reichertin kartioseulan erotustehokkuutta 10, 12,5 ja 15 asteen kallistuskulmissa. Tutkimukset tehdään ideaalisille pallomaisille lasihelmille. Mittaustulosten avulla tutkitaan myös partikkelien liikettä seulapin-nalla ja syötetyn massan vaikutusta erotustehokkuuteen. Kokeellisia mittaustulok-sia käytetään MATLAB-mallinnuksessa, jonka avulla optimoidaan kartioseulan kallistuskulmaa ja massapanosta suhteessa erotustehokkuuteen. Tutkimuksen kannalta olennaisia kysymyksiä ovat: ”Onko painovoimaan perustuva erottelu seuloilla riittävä takaamaan hyvän erotustehokkuuden?” ja ”Mikä on seulan ero-tustehokkuuden kannalta optimaalinen kallistuskulma ja syötettävä massa?” Reichertin kartioseulan etuja ovat sen energiatehokkuus ja yksinkertainen helposti säädettävä prosessi. Koemittauksista havaitaan, että erotustehokkuus vastaa opti-moinnin tuloksia. Seulan liian pieni kallistuskulma ja suuri massapanos pienentävät seulan erotustehokkuutta. Lisätutkimuksia tarvitaan eri kallistuskulmilla ja materiaaleilla, jotta tuloksia voidaan verrata todellisiin seulontaprosesseihin.

Generating competitive advantage through competitor information systems

This pro gradu –thesis discusses generating competitive advantage through competitor information systems. The structure of this thesis follows the structure of the WCA model by Alter (1996). In the WCA model, business process is influenced by three separate but connected elements: information, technology, and process participants. The main research question is how competitor information can be incorporated into or made into a tool creating competitive advantage. Research subquestions are: How does competitor information act as a part of the business process creating competitive advantage? How is a good competitor information system situated and structured in an organisation? How can management help information generate competitive advantage in the business process with participants, information, and technology? This thesis discusses each of the elements separate, but the elements are connected to each other and to competitive advantage. Information is discussed by delving into competitor information and competitor analysis. Competitive intelligence and competitor analysis requires commitment throughout the organisation, including top management, the desire to perform competitive intelligence and the desire to use the end products of that competitive intelligence. In order to be successful, systematic competitive intelligence and competitor analysis require vision, willingness to strive for the goals set, and clear strategies to proceed. Technology is discussed by taking a look into the function of the competitor information systems play and the place they occupy within an organization. In addition, there is discussion about the basic infrastructure of competitor information systems, and the problems competitor information systems can have plaguing them. In order for competitor information systems to be useful and worthy of the resources it takes to develop and maintain them, competitor information systems require on-going resource allocation and high quality information. In order for competitor information systems justify their existence business process participants need to maintain and utilize competitor information systems on all levels. Business process participants are discussed through management practices. This thesis discusses way to manage information, technology, and process participants, when the goal is to generate competitive advantage through competitor information systems. This is possible when information is treated as a resource with value, technology requires strategy in order to be successful within an organization, and process participants are an important resource. Generating competitive advantage through competitor information systems is possible when the elements of information, technology, and business process participants all align advantageously.

Supporting Repository Interoperability through Guidelines

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Study of Control Methods of a High-Frequency Cycloconverter for Domestic Induction Heating Appliances

A high-frequency cyclonverter acts as a direct ac-to-ac power converter circuit that does not require a diode bidge rectifier. Bridgeless topology makes it possible to remove forward voltage drop losses that are present in a diode bridge. In addition, the on-state losses can be reduced to 1.5 times the on-state resistance of switches in half-bridge operation of the cycloconverter. A high-frequency cycloconverter is reviewed and the charging effect of the dc-capacitors in ``back-to-back'' or synchronous mode operation operation is analyzed. In addition, a control method is introduced for regulating dc-voltage of the ac-side capacitors in synchronous operation mode. The controller regulates the dc-capacitors and prevents switches from reaching overvoltage level. This can be accomplished by variating phase-shift between the upper and the lower gate signals. By adding phase-shift between the gate signal pairs, the charge stored in the energy storage capacitors can be discharged through the resonant load and substantially, the output resonant current amplitude can be improved. The above goals are analyzed and illustrated with simulation. Theory is supported with practical measurements where the proposed control method is implemented in an FPGA device and tested with a high-frequency cycloconverter using super-junction power MOSFETs as switching devices.

Contemporary marketing in the high-tech industry: Perceptions of Finnish IT marketing professionals

Over the last 30 years, new technologies and globalization have radically changed the way in which marketing is conducted. However, whereas their effects on business in general have been widely discussed, the focus of the effects on marketing remains without clear recognition. Global research has been made to shed light onto the issue, but it has widely concentrated on the views of executives as well as the consumer markets. In addition, a research gap is existent in applying the concept of marketing change in a specific business-to-business (B2B) industry. Therefore, the main research question this study seeks to answer is: “How is contemporary marketing conducted in the high-technology industry?” In this research, the researcher considers the specific industry of high-technology. However, as the industry is comprised of differing markets, the focus will be given to one of the industry’s prime sectors – the information technology (IT) markets, where companies offer other firms products or services manufactured with advanced technology. The growing IT-market is considered of critical importance in the economies of technologically ready countries such as Finland, where this research is also conducted. Through multiple case studies the researcher aims to describe how the changes in technology, customer engagement and future trends have shaped the way in which successful high-tech marketing is conducted in today’s marketplace. Then, results derived from the empirical research are presented to the reader with links to existing literature. As a conclusion, a generalized framework is constructed to depict and ideal marketer-customer relationship, with emphasis on dynamic, two-way communication and its supporting elements of customer analytics, change adaptation, strategic customer communication and organizational support. From a managerial point of view, the research may provide beneficial information as contemporary marketing can yield profitable outcomes if managed correctly. As a new way to grasp competitive advantage, strategic marketing is much more data-driven and customer-focused than ever before. The study can also prove to be relevant for the academic communities, while its results may act as inspiring for new focus on the education trends of future marketers. This study was limited to the internal activities done at the high-tech industry, leaving out the considerations for co-marketing, marketing via business partners or marketing at other B2B-industries.

Digital Humanities For Everyone’s Benefit?: interplay in social media with the great audience, high-esteemed researcher and self-conscious library

The National Library of Finland realizes the Digitization Project of Kindred Languages in 2012–15. The project is financially supported by the Kone Foundation. During this project the National Library of Finland has digitized and made available approximately 1200 monograph and more than 100 newspaper titles in several Uralic languages. The materials are available to both researchers and citizens in the National Library’s Fenno-Ugrica collection. The project will produce digitized materials in the Uralic languages as well as their development tools to support linguistic research and citizen science. The resulting materials will constitute the largest resource for the Uralic languages in the world. Through this project, researchers will gain access to corpora which they have not been able to study before and to which all users will have open access regardless of their place of residence. In my presentation, I will discuss 1) how we utilized the social media (Facebook, Twitter, VKontakte etc) to gain audience for our collection and 2) how the needs of researchers and laymen were met in crowdsourcing.

Managing Customer Co-creation: Empirical Evidence from Finnish High-tech SMEs

The purpose of this thesis is to find out how customer co-creation activities are managed in Finnish high-tech SMEs by understanding managers’ views on relevant issues. According to theory, issues such as firm size, customer knowledge implementation, lead customers, the fuzzy front-end of product/service development as well as the reluctance to engage in customer co-creation are some of the field’s focal issues. The views of 145 Finnish SME managers on these issues were gathered as empirical evidence through an online questionnaire and analyzed with SPSS statistics software. The results show, firstly, that Finnish SME managers are aware of the issues associated with customer co-creation and are able to actively manage them. Additionally, managers performed well in regards to collaborating with lead customers and implemented customer knowledge evenly in various stages of their new product and service development processes. Intellectual property rights emerged as an obstacle deterring managers from engaging in co-creation. The results suggest that in practice managers would do well by looking for more opportunities to implement customer knowledge in the early and late stages of new product and service development, as well as by actively searching for lead customers.

Electromagnetic and thermal design of a multilevel converter with high power density and reliability

Electric energy demand has been growing constantly as the global population increases. To avoid electric energy shortage, renewable energy sources and energy conservation are emphasized all over the world. The role of power electronics in energy saving and development of renewable energy systems is significant. Power electronics is applied in wind, solar, fuel cell, and micro turbine energy systems for the energy conversion and control. The use of power electronics introduces an energy saving potential in such applications as motors, lighting, home appliances, and consumer electronics. Despite the advantages of power converters, their penetration into the market requires that they have a set of characteristics such as high reliability and power density, cost effectiveness, and low weight, which are dictated by the emerging applications. In association with the increasing requirements, the design of the power converter is becoming more complicated, and thus, a multidisciplinary approach to the modelling of the converter is required. In this doctoral dissertation, methods and models are developed for the design of a multilevel power converter and the analysis of the related electromagnetic, thermal, and reliability issues. The focus is on the design of the main circuit. The electromagnetic model of the laminated busbar system and the IGBT modules is established with the aim of minimizing the stray inductance of the commutation loops that degrade the converter power capability. The circular busbar system is proposed to achieve equal current sharing among parallel-connected devices and implemented in the non-destructive test set-up. In addition to the electromagnetic model, a thermal model of the laminated busbar system is developed based on a lumped parameter thermal model. The temperature and temperature-dependent power losses of the busbars are estimated by the proposed algorithm. The Joule losses produced by non-sinusoidal currents flowing through the busbars in the converter are estimated taking into account the skin and proximity effects, which have a strong influence on the AC resistance of the busbars. The lifetime estimation algorithm was implemented to investigate the influence of the cooling solution on the reliability of the IGBT modules. As efficient cooling solutions have a low thermal inertia, they cause excessive temperature cycling of the IGBTs. Thus, a reliability analysis is required when selecting the cooling solutions for a particular application. The control of the cooling solution based on the use of a heat flux sensor is proposed to reduce the amplitude of the temperature cycles. The developed methods and models are verified experimentally by a laboratory prototype.

Sustainable Development – the Key to Competitiveness CSR as an added value to Alstom’s corporate performance

Corporate social responsibility or CSR is today a widely recognized concept which is receiving in- creasing popularity extremely rapidly, especially in the business world. The pressure on companies to carry out their business practices in ethical manners, which promote the wellbeing of the environment and society, is coming from all directions and all stakeholders. Alstom, a French multinational conglomerate operating in the rail transport and energy industry, is no exception to this norm. This company, which will be used as the case example in this thesis, is being brought to bay in terms of engaging in CSR practices and practicing business with high ethics. It is surely not a negatively conceived phenomenon that CSR is being put on a pedestal – quite the opposite. Instead of corporations practicing CSR only to meet their stakeholder requirements through practicing window dressing, many corporations actually strive to benefit from the practice of corporate social business. In addition to bringing benefit to externals a corporation such as Alstom itself can benefit from being involved in CSR. The purpose of this thesis is to evaluate the current strategic values and the future perspectives of CSR at Alstom and moreover the added value which the practice of CSR could bring Alstom as a business. A set of perspectives from a futures studies viewpoint is looked at, with critical examination of the company’s current corporate practices as well as the CSR related studies and theories written for corporations. Through this, some solutions and practices will be suggested to Alstom in order for it to fully utilize the potential of corporate social business and the value it can bring in the most probable futures that the company is expected to face. By utilizing the Soft Systems Methodology (SSM), a method mainly used in organizations to solve problematic issues in management and policy contexts, a process is developed to see what improvements could be of help in improving Alstom and its way towards involving CSR in its business practices even more than it currently does. Alstom is already deeply involved in the practicing of CSR and its vision has a strong emphasis on this popular concept of today. In order to stay in the game and to use CSR as a competitive advantage to the company, Alstom ought to embed corporate social practices even deeper in its organizational culture by using them as a tool to reduce risk and costs, increasing employee commitment and customer loyalty and to attract socially responsible investors, just to name a few. CSR as a concept is seen to have great potential in the future, an opportunity Alstom will not miss.

The role of metal ions in selective and sustainable processes

Sustainability and recycling are core values in today’s industrial operations. New materials, products and processes need to be designed in such a way as to consume fewer of the diminishing resources we have available and to put as little strain on the environment as possible. An integral part of this is cleaning and recycling. New processes are to be designed to improve the efficiency in this aspect. Wastewater, including municipal wastewaters, is treated in several steps including chemical and mechanical cleaning of waters. Well-cleaned water can be recycled and reused. Clean water for everyone is one of the greatest challenges we are facing today. Ferric sulphate, made by oxidation from ferrous sulphate, is used in water purification. The oxidation of ferrous sulphate, FeSO4, to ferric sulphate in acidic aqueous solutions of H2SO4 over finely dispersed active carbon particles was studied in a vigorously stirred batch reactor. Molecular oxygen was used as the oxidation agent and several catalysts were screened: active carbon, active carbon impregnated with Pt, Rh, Pd and Ru. Both active carbon and noble metal-active carbon catalysts enhanced the oxidation rate considerably. The order of the noble metals according to the effect was: Pt >> Rh > Pd, Ru. By the use of catalysts, the production capacities of existing oxidation units can be considerably increased. Good coagulants have a high charge on a long polymer chain effectively capturing dirty particles of the opposite charge. Analysis of the reaction product indicated that it is possible to obtain polymeric iron-based products with good coagulation properties. Systematic kinetic experiments were carried out at the temperature and pressure ranges of 60B100°C and 4B10 bar, respectively. The results revealed that both non-catalytic and catalytic oxidation of Fe2+ to Fe3+ take place simultaneously. The experimental data were fitted to rate equations, which were based on a plausible reaction mechanism: adsorption of dissolved oxygen on active carbon, electron transfer from Fe2+ ions to adsorbed oxygen and formation of surface hydroxyls. A comparison of the Fe2+ concentrations predicted by the kinetic model with the experimentally observed concentrations indicated that the mechanistic rate equations were able to describe the intrinsic oxidation kinetics of Fe2+ over active carbon and active carbon-noble metal catalysts. Engineering aspects were closely considered and effort was directed to utilizing existing equipment in the production of the new coagulant. Ferrous sulphate can be catalytically oxidized to produce a novel long-chained polymeric iron-based flocculent in an easy and affordable way in existing facilities. The results can be used for modelling the reactors and for scale-up. Ferric iron (Fe3+) was successfully applied for the dissolution of sphalerite. Sphalerite contains indium, gallium and germanium, among others, and the application can promote their recovery. The understanding of the reduction process of ferric to ferrous iron can be used to develop further the understanding of the dissolution mechanisms and oxidation of ferrous sulphate. Indium, gallium and germanium face an ever-increasing demand in the electronics industry, among others. The supply is, however, very limited. The fact that most part of the material is obtained through secondary production means that real production quota depends on the primary material production. This also sets the pricing. The primary production material is in most cases zinc and aluminium. Recycling of scrap material and the utilization of industrial waste, containing indium, gallium and geranium, is a necessity without real options. As a part of this study plausible methods for the recovery of indium, gallium and germanium have been studied. The results were encouraging and provided information about the precipitation of these valuables from highly acidic solutions. Indium and gallium were separated from acidic sulphuric acid solutions by precipitation with basic sulphates such as alunite or they were precipitated as basic sulphates of their own as galliunite and indiunite. Germanium may precipitate as a basic sulphate of a mixed composition. The precipitation is rapid and the selectivity is good. When the solutions contain both indium and gallium then the results show that gallium should be separated before indium to achieve a better selectivity. Germanium was separated from highly acidic sulphuric acid solutions containing other metals as well by precipitating with tannic acid. This is a highly selective method. According to the study other commonly found metals in the solution do not affect germanium precipitation. The reduction of ferric iron to ferrous, the precipitation of indium, gallium and germanium, and the dissolution of the raw materials are strongly depending on temperature and pH. The temperature and pH effect were studied and which contributed to the understanding and design of the different process steps. Increased temperature and reduced pH improve the reduction rate. Finally, the gained understanding in the studied areas can be employed to develop better industrial processes not only on a large scale but also increasingly on a smaller scale. The small amounts of indium, gallium and germanium may favour smaller and more locally bound recovery.

Impact of Word-of-Mouth on consumer decision-making: An information processing perspective in the context of a high-involvement service

This doctoral study conducts an empirical analysis of the impact of Word-of-Mouth (WOM) on marketing-relevant outcomes such as attitudes and consumer choice, during a high-involvement and complex service decision. Due to its importance to decisionmaking, WOM has attracted interest from academia and practitioners for decades. Consumers are known to discuss products and services with one another. These discussions help consumers to form an evaluative opinion, as WOM reduces perceived risk, simplifies complexity, and increases the confidence of consumers in decisionmaking. These discussions are also highly impactful as WOM is a trustworthy source of information, since it is independent from the company or brand. In responding to the calls for more research on what happens after WOM information is received, and how it affects marketing-relevant outcomes, this dissertation extends prior WOM literature by investigating how consumers process information in a highinvolvement service domain, in particular higher-education. Further, the dissertation studies how the form of WOM influences consumer choice. The research contributes to WOM and services marketing literature by developing and empirically testing a framework for information processing and studying the long-term effects of WOM. The results of the dissertation are presented in five research publications. The publications are based on longitudinal data. The research leads to the development of a proposed theoretical framework for the processing of WOM, based on theories from social psychology. The framework is specifically focused on service decisions, as it takes into account evaluation difficulty through the complex nature of choice criteria associated with service purchase decisions. Further, other gaps in current WOM literature are taken into account by, for example, examining how the source of WOM and service values affects the processing mechanism. The research also provides implications for managers aiming to trigger favorable WOM through marketing efforts, such as advertising and testimonials. The results provide suggestions on how to design these marketing efforts by taking into account the mechanism through which information is processed, or the form of social influence.

Targeting oncogenic signaling proteins : new insights using a FRET-based chemical biology approach

Cancer affects more than 20 million people each year and this rate is increasing globally. The Ras/MAPK-pathway is one of the best-studied cancer signaling pathways. Ras proteins are mutated in almost 20% of all human cancers and despite numerous efforts, no effective therapy that specifically targets Ras is available to date. It is now well established that Ras proteins laterally segregate on the plasma membrane into transient nanoscale signaling complexes called nanoclusters. These Ras nanoclusters are essential for the high-fidelity signal transmission. Disruption of nanoclustering leads to reduction in Ras activity and signaling, therefore targeting nanoclusters opens up important new therapeutic possibilities in cancer. This work describes three different studies exploring the idea of membrane protein nanoclusters as novel anti-cancer drug targets. It is focused on the design and implementation of a simple, cell-based Förster Resonance Energy Transfer (FRET)-biosensor screening platform to identify compounds that affect Ras membrane organization and nanoclustering. Chemical libraries from different sources were tested and a number of potential hit molecules were validated on full-length oncogenic proteins using a combination of imaging, biochemical and transformation assays. In the first study, a small chemical library was screened using H-ras derived FRET-biosensors. Surprisingly from this screen, commonly used protein synthesis inhibitors (PSIs) were found to specifically increase H-ras nanoclustering and downstream signalling in a H-ras dependent manner. Using a representative PSI, increase in H-ras activity was shown to induce cancer stem cell (CSC)-enriched mammosphere formation and tumor growth of breast cancer cells. Moreover, PSIs do not increase K-ras nanoclustering, making this screening approach suitable for identifying Ras isoform-specific inhibitors. In the second study, a nanoncluster-directed screen using both H- and K-ras derived FRET biosensors identified CSC inhibitor salinomycin to specifically inhibit K-ras nanocluster organization and downstream signaling. A K-ras nanoclusteringassociated gene signature was established that predicts the drug sensitivity of cancer cells to CSC inhibitors. Interestingly, almost 8% of patient tumor samples in the The Cancer Genome Atlas (TCGA) database had the above gene signature and were associated with a significantly higher mortality. From this mechanistic insight, an additional microbial metabolite screen on H- and K-ras biosensors identified ophiobolin A and conglobatin A to specifically affect K-ras nanoclustering and to act as potential breast CSC inhibitors. In the third study, the Ras FRET-biosensor principle was used to investigate membrane anchorage and nanoclustering of myristoylated proteins such as heterotrimeric G-proteins, Yes- and Src-kinases. Furthermore, Yes-biosensor was validated to be a suitable platform for performing chemical and genetic screens to identify myristoylation inhibitors. The results of this thesis demonstrate the potential of the Ras-derived FRETbiosensor platform to differentiate and identify Ras-isoform specfic inhibitors. The results also highlight that most of the inhibitors identified predominantly perturb Ras subcellular distribution and membrane organization through some novel and yet unknown mechanisms. The results give new insights into the role of Ras nanoclusters as promising new molecular targets in cancer and in stem cells.

Internal Changes in International New Ventures During Initial Internationalization: Finnish SMEs Operating in Dynamic High-tech Industries

The purpose of this qualitative research is to study how international new ventures change internally during initial internationalization. Based on the analysis of seven INV firms, a framework illustrating this change process, will be developed. This research will also develop earlier theories, and create a solid combination of existing theories to explain the phenomenon. INV firms internationalize more rapidly and aggressively than traditional MNEs. At the same, external and internal drivers cause changes in INVs culture, resources, capabilities, strategic management, and output decisions inside the company. Organizational learning and resource acquisition through international business networks explain how INVs are able to cope with the dynamic high-technology industry and be able to adapt. Internationalization of INVs proceeds through several phases, which may be gone through rapidly due to the network effects and INVs’ special characteristics. The results of this research revealed that INVs internal change process proceeds through four phases; pre-incorporation phase, product development phase, internationalization and growth phase, and maturation phase. INVs culture, resources, capabilities, strategic management, and outputs change significantly during initial internationalization, and INVs develop from small start-ups into fully established companies.