Analysis of the voltage source inverter with small DC-link capacitor

IIn electric drives, frequency converters are used to generatefor the electric motor the AC voltage with variable frequency and amplitude. When considering the annual sale of drives in values of money and units sold, the use of low-performance drives appears to be in predominant. These drives have tobe very cost effective to manufacture and use, while they are also expected to fulfill the harmonic distortion standards. One of the objectives has also been to extend the lifetime of the frequency converter. In a traditional frequency converter, a relatively large electrolytic DC-link capacitor is used. Electrolytic capacitors are large, heavy and rather expensive components. In many cases, the lifetime of the electrolytic capacitor is the main factor limiting the lifetime of the frequency converter. To overcome the problem, the electrolytic capacitor is replaced with a metallized polypropylene film capacitor (MPPF). The MPPF has improved properties when compared to the electrolytic capacitor. By replacing the electrolytic capacitor with a film capacitor the energy storage of the DC-linkwill be decreased. Thus, the instantaneous power supplied to the motor correlates with the instantaneous power taken from the network. This yields a continuousDC-link current fed by the diode rectifier bridge. As a consequence, the line current harmonics clearly decrease. Because of the decreased energy storage, the DC-link voltage fluctuates. This sets additional conditions to the controllers of the frequency converter to compensate the fluctuation from the supplied motor phase voltages. In this work three-phase and single-phase frequency converters with small DC-link capacitor are analyzed. The evaluation is obtained with simulations and laboratory measurements.

Railcarrier in Intermodal Freight Transportation Network

The major objective of this thesis is to describe and analyse how a railcarrier is engaged in an intermodal freight transportation network through its role and position. Because of the fact that the role as a conceptualisation has a lot of parallels with the position, both these phenomena are evaluated theoretically and empirically. VR Cargo (a strategical business unitof the Finnish railway company VR Ltd.) was chosen to be the focal firm surrounded by the actors of the focal net. Because of the fact that networks are sets of relationships rather than sets of actors, it is essential to describe the dimensions of the relationships created through the time thus having a past, presentand future. The roles are created during long common history shared by the actors especially when IM networks are considered. The presence of roles is embeddedin the tasks, and the future is anchored to the expectations. Furthermore, in this study role refers to network dynamics, and to incremental and radical changes in the network, in a similar way as position refers to stability and to the influences of bonded structures. The main purpose of the first part of the study was to examine how the two distinctive views that have a dominant position in modern logistics ¿ the network view (particularly IMP-based network approach) and the managerial view (represented by Supply Chain Management) differ, especially when intermodalism is under consideration. In this study intermodalism was defined as a form of interorganisational behaviour characterized by the physical movement of unitized goods with Intermodal Transport Units, using more than one mode as performed by the net of operators. In this particular stage the study relies mainly on theoretical evaluation broadened by some discussions with the practitioners. This is essential, because the continuous dialogue between theory and practice is highly emphasized. Some managerial implications are discussed on the basis of the theoretical examination. A tentative model for empirical analysis in subsequent research is suggested. The empirical investigation, which relies on the interviews among the members in the focal net, shows that the major role of the focal company in the network is the common carrier. This role has some behavioural and functional characteristics, such as an executive's disclosure expressing strategic will attached with stable and predictable managerial and organisational behaviour. Most important is the notion that the focal company is neutral for all the other operators, and willing to enhance and strengthen the collaboration with all the members in the IM network. This also means that all the accounts are aimed at being equal in terms of customer satisfaction. Besides, the adjustments intensify the adopted role. However, the focal company is also obliged tosustain its role as it still has a government-erected right to maintain solely the railway operations on domestic tracks. In addition, the roles of a dominator, principal, partner, subcontractor, and integrator were present appearing either in a dyadic relationship or in net(work) context. In order to reveal differentroles, a dualistic interpretation of the concept of role/position was employed.

The Design and Implementation of Loudspeaker Control Network Protocols

The networking and digitalization of audio equipment has created a need for control protocols. These protocols offer new services to customers and ensure that the equipment operates correctly. The control protocols used in the computer networks are not directly applicable since embedded systems have resource and cost limitations. In this master's thesis the design and implementation of new loudspeaker control network protocols are presented. The protocol stack was required to be reliable, have short response times, configure the network automatically and support the dynamic addition and removal of loudspeakers. The implemented protocol stack was also required to be as efficient and lightweight as possible because the network nodes are fairly simple and lack processing power. The protocol stack was thoroughly tested, validated and verified. The protocols were formally described using LOTOS (Language of Temporal Ordering Specifications) and verified using reachability analysis. A prototype of the loudspeaker network was built and used for testing the operation and the performance of the control protocols. The implemented control protocol stack met the design specifications and proved to be highly reliable and efficient.

Transport Resource Management within UMTS Radio Network Subsystem

Tällä hetkellä haastavin telekommunikaatioteollisuuden tutkimus – ja kehitystoiminta on keskittynyt kolmannen sukupolven matkapuhelinjärjestelmien ympärille. Järjestelmien standardointityössä on saatu aikaiseksi ensimmäiset vakaat spesifikaatioversiot ja kaupallista toimintaa ollaan parhaillaan aloittelemassa Japanissa ja Euroopassa. Eräs kolmannen sukupolven järjestelmistä on UMTS (Universal Mobile Telecommunications System). Tämä diplomityö antaa yleiskuvan UMTS järjestelmästä ja sen eri verkkoelementtien toiminnallisuuksista. Päähuomio on kiinnitetty radioverkkojärjestelmään (UMTS Terrestrial Radio Access Network) ja erityisesti sen radioaliverkkojärjestelmään (Radio Network Subsystem), joka koostuu radioverkonohjaimesta (Radio Network Controller) ja joukosta siihen kuuluvia tukiasemia (Node B). Radioverkonohjain ja tukiasemat on yhdistetty avoimen rajapinnan kautta jota kutsutaan Iub -rajapinnaksi. Rajapinta tarjoaa radioverkonohjaimelle mahdollisuuden kontrolloida tukiasemia signalointiviestien avulla ja mahdollistaa tehokkaan ja luotettavan käyttäjätiedon siirron radioaliverkkojärjestelmän sisällä. Tämän diplomityön pääasiallinen sisältö on siirtoresurssien hallinta Iub -rajapinnan ylitse. Työssä esitellään ja selitetään siirtoverkon arkkitehtuuri. Myös kaikki Iub:ssä sijaitsevat protokollat ja toiminnalliset yksiköt jotka vaikuttavat siirtoresurssien hallintaan esitellään ja kuvataan yksityiskohtaisesti. Päähuomio on kiinnitetty sovellusprotokolliin sekä rajapinnan siirtoverkko- että radioverkkokerroksella sekä näiden protokollien väliseen vuorovaikutukseen. Kyseiset protokollat ovat Node B Application Part (NBAP) ja Access Link Control Application Part (ALCAP). Työn toteutusosassa käydään lävitse NBAP –protokollan prototyypin ja Node B Manager –toiminnallisen yksikön prototyypin implementaatio.

Competitive Analysis of the Northwest Russian Transport Logistics Cluster – Finnish Perspective

Tutkimus tarkastelee Luoteis-Venäjän liikennelogistiikkaklusteria. Tarkoitus on selvittää klusterin nykyinen rakenne ja kilpailukyky sekä klusterin tarjoamat liiketoimintamahdollisuudet suomalaisille logistiikkayrityksille. Työssä käsitellään neljää perusliikennemuotoa: rautatie-, maantie-, meri- ja sisävesi-, sekä ilmaliikennettä. Tutkimuksen aineisto on kerätty tutkimusta varten laadituista kyselyistä, haastatteluista sekä aiemmin julkaistusta materiaalista. Venäjä on suunnitellut kehittävänsä voimakkaasti liikenneinfrastruktuuria, mm. julkaisemalla protektionistisen liikennestrategiasuunnitelman. Ongelmana ovat olleet toteutukset, jotka ovat jääneet yleensä puutteellisiksi. Tällä hetkellä todellista kilpailukykyä löytyy ainoastaan rautatieliikenteestä, muut kolme liikennemuotoa omaavat potentiaalisen kilpailukyvyn. Venäjällä on mahdollisuus hyötyä laajasta pinta-alastaan Aasian ja Euroopan liikenteen yhdistäjänä. Yksi konkreettisimmista esimerkeistä on Trans Siperian rautatie, joka kaipaisi vielä lisäkehitystä. Suomi on toiminut Venäjän liikenteessä arvotavaran kauttakulkumaana, vuonna 2003 noin 30–40 % Venäjän tuonnin arvosta kulki Suomen kautta. Venäjälle tullaan tuomaan arvotavaraa vielä useita vuosia, mutta reittien osalta kilpailu on tiukentunut. Suomalaisten yritysten liiketoimintamahdollisuuksiin esitetään kaksi mallia: kauttakulkuliikenteen lisäarvologistiset (VAL) operaatiot Suomessa tai etabloituminen Venäjän logistisiin ketjuihin. Suomalaisten olisi syytä parantaa yhteistyötään yritysten ja yliopistojen ym. koulutuslaitosten välillä. Myös yhteistyökumppaneiden hakeminen esimerkiksi Ruotsista voisi tuoda merkittäviä etuja. Suomalaista osaamista voitaisiin hyödyntää parhaiten etabloitumalla Venäjän markkinoille, esimerkiksi keskittymällä Venäjän logististen ketjujen johtamiseen. Myös VAL palveluiden johtamiseen Venäjällä olisi erittäin hyvä tilaisuus, koska Venäjän oma tietotaito logistiikassa ei ole vielä kehittynyt kansainväliselle tasolle, mutta kustannustaso on alhaisempi kuin Suomessa.

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

Reliability analysis of medium voltage feeder

Distribution companies are facing numerous challenges in the near future. Regulation defines correlation between power quality and revenue cap. Companies have to take measures for reliability increase to successfully compete in modern conditions. Most of the failures seen by customers originate in medium voltage networks. Implementation of network automation is the very effective measure to reduce duration and number of outages, and consequently, outage costs. Topic of this diploma work is study of automation investments effect on outage costs and other reliability indices. Calculation model have been made to perform needed reliability calculations. Theoretical study of different automation scenarios has been done. Case feeder from actual distribution company has been studied and various renovation plans have been suggested. Network automation proved to be effective measure for increasing medium voltage network reliability.

Wide Area Network Acceleration in Corporate Networks

There are several factors affecting network performance. Some of these can be controlled whereas the others are more fixed. These factors are studied in this thesis from the wide area network (WAN) perspective and the focus is on corporate networks. Another area of interest is the behavior of application protocols when used through WAN. The aim is to study the performance of commonly used application protocols in corporate networks. After identifying the performance problems in corporate WANs the thesis concentrates on methods for improving WAN performance. WAN acceleration is presented as a possible solution. The different acceleration methods are discussed in order to give the reader a theoretical view on how the accelerators can improve WAN performance. Guidelines on the installation of accelerators into a network are also discussed. After a general overview on accelerators is given, one accelerator vendor currently on market is selected for a further analysis. The work is also a case study where two accelerators are installed into a target company network for testing purposes. The tests are performed with three different application protocols that have been identified as critical applications for the target corporation. The aim of the tests is to serve as a proof of concept for WAN acceleration in the target network.

GPRS/EDGE Session Tracing and Analysis in Abis and AGPRS Interfaces

Efficient problem solving in cellular networks is important when enhancing the network performance and liability. Analysis of calls and packet switched sessions in protocol level between the network elements is an important part of this process. They can provide very detailed information about error situations which otherwise would be difficult to recognise. In this thesis we seek solutions for monitoring GPRS/EDGE sessions in two specific interfaces simultaneously in such manner that all information important to the users will be provided in easily understandable form. This thesis focuses on Abis and AGPRS interfaces of GSM radio network and introduces a solution for managing the correlation between these interfaces by using signalling messages and common parameters as linking elements. ~: Finally this thesis presents an implementation of GPRS/EDGE session monitoring application for Abis and AGPRS interfaces and evaluates its benefits to the end users. Application is implemented as a part of Windows based 3G/GSM network analyser.

Quality and analysis of administration processes in server operations

IT outsourcing refers to the way companies focus on their core competencies and buy the supporting functions from other companies specialized in that area. Service is the total outcome of numerous of activities by employees and other resources to provide solutions to customers' problems. Outsourcing and service business have their unique characteristics. Service Level Agreements quantify the minimum acceptable service to the user. The service quality has to be objectively quantified so that its achievement or non-achievement of it can be monitored. Usually offshoring refers to the transferring of tasks to low-cost nations. Offshoring presents a lot of challenges that require special attention and they need to be assessed thoroughly. IT Infrastructure management refers to installation and basic usability assistance of operating systems, network and server tools and utilities. ITIL defines the industry best practices for organizing IT processes. This thesis did an analysis of server operations service and the customers’ perception of the quality of daily operations. The agreed workflows and processes should be followed better. Service providers’ processes are thoroughly defined but both the customer and the service provider might disobey them. Service provider should review the workflows regarding customer functions. Customer facing functions require persistent skill development, as they communicate the quality to the customer. Service provider needs to provide better organized communication and knowledge exchange methods between the specialists in different geographical locations.

Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Network Structures and Modularity among Biofuel Heating System Manufacturers

The aim of this thesis was to study network structures and modularity among biofuel heating system manufacturers in the Finnish bioenergy sector by utilizing the perspectives of numerous Finnish bioenergy specialists. The study is qualitative due to the fact that the research material was gathered with semi-structured theme interviews during May and June 2010. The research methodology used in the thesis combines conceptual and action-oriented approach. Networks, value nets, and modularity were studied from different perspectives. Three network and platform strategies were discovered and a general network structure was formed. Moreover, benefits and disadvantages of networks and modularity among biofuel heating system manufacturers were illustrated. The analysis provides a comprehensive perception of the industry. The results of the research were constructed by implementing existing theories into practice. Also future recommendations for the biofuel heating system manufacturers were given. The results can be considered to be beneficial because the number of previous studies about the subject is relatively small. The reliability of the study is eminent because the number of the interviews was inclusive.

Design and Analysis of Forward Error Control Coding and Signaling for Guaranteeing QoS in Wireless Broadcast Systems

Broadcasting systems are networks where the transmission is received by several terminals. Generally broadcast receivers are passive devices in the network, meaning that they do not interact with the transmitter. Providing a certain Quality of Service (QoS) for the receivers in heterogeneous reception environment with no feedback is not an easy task. Forward error control coding can be used for protection against transmission errors to enhance the QoS for broadcast services. For good performance in terrestrial wireless networks, diversity should be utilized. The diversity is utilized by application of interleaving together with the forward error correction codes. In this dissertation the design and analysis of forward error control and control signalling for providing QoS in wireless broadcasting systems are studied. Control signaling is used in broadcasting networks to give the receiver necessary information on how to connect to the network itself and how to receive the services that are being transmitted. Usually control signalling is considered to be transmitted through a dedicated path in the systems. Therefore, the relationship of the signaling and service data paths should be considered early in the design phase. Modeling and simulations are used in the case studies of this dissertation to study this relationship. This dissertation begins with a survey on the broadcasting environment and mechanisms for providing QoS therein. Then case studies present analysis and design of such mechanisms in real systems. The mechanisms for providing QoS considering signaling and service data paths and their relationship at the DVB-H link layer are analyzed as the first case study. In particular the performance of different service data decoding mechanisms and optimal signaling transmission parameter selection are presented. The second case study investigates the design of signaling and service data paths for the more modern DVB-T2 physical layer. Furthermore, by comparing the performances of the signaling and service data paths by simulations, configuration guidelines for the DVB-T2 physical layer signaling are given. The presented guidelines can prove useful when configuring DVB-T2 transmission networks. Finally, recommendations for the design of data and signalling paths are given based on findings from the case studies. The requirements for the signaling design should be derived from the requirements for the main services. Generally, these requirements for signaling should be more demanding as the signaling is the enabler for service reception.

Virtual Professional Network as a Value Creator in the Dental Business

The research of virtual professional networks has been enormous but the lack of research in the dental field was obvious. This study focuses on those uses and gratifications, and motives of participants that a virtual pro-fessional network should fulfil. The aim of this study is to understand the factors behind the successful virtual professional network, and motives of participants that support a particular business network’s building up for contributing its further success. In this study the focus is on particular mo-tives, needs and benefits of participants that are significant for the net-work’s further development. The study will explore relevant scientific research and theory that is char-acteristic in networking, and theories of user’s needs and motives. Empiri-cal data was collected from dental professionals by net based question-naire that was sent by e-mail. Data analysis was done by quantitative fac-tor analysis. The findings of this study were obvious that virtual knowledge of implantology is inadequate and knowledge is rather difficult to find in the Internet. Sharing of virtual knowledge, net-learning and communication were seen to improve the quality of impolantological professionalism and also the development of these areas was experienced essential. On the grounds of this study a host of a virtual professional network can focus on those aspects that serve the users at best, can develop professionalism in implantology and can profit in its own business operations.

Spare part business analysis and development

The purpose of this Thesis was to comprehensively analyze and develop the spare part business in Company Oy’s five biggest product groups by searching development issues related to single spare parts’ supply chains as well as the spare part business process, make implementation plans for them and implement the plans when possible. The items were classified based on special characteristics of spare parts and on their actual sales volumes. The created item classes were examined for finding improvement possibilities. Management strategies for classified items were suggested. Vendors and customers were analyzed for supporting the comprehensive supply network development work. The effectiveness of the current spare part business process was analyzed in co-operation with the spare part teams in three business unit locations. Several items were taken away from inventories as uselessly stocked items. Price list related to core items with one of the main product group’s core item manufacturer was suggested to be expanded in Town A. Refinement equipment seal item supply chain management was seen important to develop in Town B. A new internal business process model was created for minimizing and enhancing the internal business between Company’s business units. SAP inventory reports and several other features were suggested to be changed or developed. Also the SAP data material management was seen very important to be developed continuously. Many other development issues related to spare parts’ supply chains and the work done in the business process were found. The need for investigating the development possibilities deeper became very clear during the project.