Integration of the Food Waste Disposer Unit to the Existing Sewage System

Among the numerous approaches to food waste treatment, the food waste disposers method (FWDs), as a newcomer, has become slowly accepted by the general public owing to the worries about its impact on the existing sewage system. This paper aims to justify the role of FWDs in the process of urbanization in order to better prepare a city to take good care of the construction of its infrastructure and the solid waste treatment. Both the literatures and the case study help to confirm that FWDs has no negative effects on the wastewater treatment plant and it is also environmental friendly by reducing the greenhouse gas emissions. In the case study, the Lappeenranta waste water treatment plant has been selected in order to figure out the possible changes to a WWTP following the integration of FWDs: the observation shows only minor changes take place in a WWTP, in case of 25% application, like BOD up 7%, TSS up 6% and wastewater flowrate up 6%, an additional sludge production of 200 tons per year and the extra yield of methane up to 10000m3 per year; however, when the utilization rate of FWD is over 75%, BOD, TSS, and wastewater flowrate will experience more significant changes, thus exerting much pressure on the existing WWTP. FWDs can only be used in residential areas or cities equipped with consummate drainage network within the service sphere of WWTP, therefore, the relevant authority or government department should regulate the installation frequency of FWDs, while promoting the accessory application of FWDs. In the meanwhile, WWTP should improve their treatment process in order to expand their capacity for sludge treatment so as to stay in line with the future development of urban waste management.

Quasi-objects and actors in the web of belief. Formation of a national nuclear waste management system: the case of Finland

Paper presented in ISA RC23 meeting, Gothenburg July 16th 2010

Yritysvastuu ympäristönäkökulmasta

Diplomityön tavoitteena on selvittää yritysvastuun sisältöä ja merkitystä yritysten toiminnassa. Vastuullinen yritystoiminta sisältää taloudellisen, sosiaalisen ja ympäristön näkökulman. Ne ovat yksi edellytys yrityksen toiminnan jatkuvuudelle ja menestykselle. Työssä keskitytään erityisesti yritysvastuun ympäristönäkökulmaan, sillä ympäristöasiat ovat yhä enemmän esillä. Huoli ympäristön tilasta on lisääntynyt selvästi ja myös kuluttajat vaativat yrityksiltä vastuullista toimintaa. Lisäksi ympäristöön liittyvä lainsäädäntö kiristyy ja säädökset lisääntyvät. Kestävän kehityksen mukainen toiminta säästää luonnonvaroja ja vähentää ympäristön saastumista. Ympäristöasiat on huomioitava yrityksen kaikessa toiminnassa. Vihreässä taloudessa ympäristölle aiheutuu mahdollisimman vähän haittaa. Yrityksillä on merkittävä asema vihreän talouden kehittämisessä, sillä yritykset voivat vähentää toiminnasta aiheutuvia ympäristövaikutuksia, tuottaa ympäristöä säästäviä tuotteita sekä tarjota ratkaisuja ympäristövaikutusten pienentämiseen. Uuden teknologian kehittäminen on kestävän kehityksen kannalta oleellista ja siten voidaan myös saavuttaa kilpailuetua. Yritysten ympäristövastuullista toimintaa tukevat ympäristöpolitiikka ja –strategia, ympäristöjohtaminen, ympäristöjärjestelmät, ympäristöriskianalyysit, ympäristölaskenta sekä ympäristönmyötäinen tuotesuunnittelu. Nämä ovat työkaluja, jotka selventävät yritysten ympäristöön liittyviä tavoitteita ja päämääriä. Niitä voidaan hyödyntää päätöksenteon tukena ja ympäristöasioiden kehittämisessä. Ympäristökysymykset on myös tärkeää saada yhdistetyksi yritysten taloudelliseen ohjaukseen ja tuotesuunnitteluun. Työn perusteella voidaan todeta, että vastuullinen toiminta on merkittävä osa yritysten kilpailukykyä ja se on tärkeää yrityksen tulevaisuuden kannalta. Vastuullisuus on ehdottomasti yksi edellytys yritysten toiminnan jatkuvuudelle. Vastuullinen toiminta edistää yrityksen kilpailukykyä ja sen avulla voidaan saavuttaa myös uusia asiakkaita ja markkina-alueita. Ympäristöystävällisempien tuotteiden kehittäminen, jätteen määrän vähentäminen ja prosessien tehostaminen tuovat yrityksille kustannussäästöjä. Vastuullinen toiminta lisää yritysten innovatiivisuutta ja uusien liiketoimintamallien syntymistä. Kuluttajavalinnoissa painottuvat enemmän myös ympäristöön ja yhteiskuntaan liittyvät arvot, joten vastuullisuus voi lisätä kysyntää ja asiakkaiden määrää. Myös rahoittajat ja uudet työntekijät ovat kiinnostuneita vastuullisista yrityksistä. Vastuullinen yritys nähdään houkuttelevana ja luotettavana yhteistyökumppanina.

Waste Stream Investigation from Perspective of Changing Waste Legislation at Green Sand Foundries

The update of the Finnish legislation concerning waste was unavoidable, to comply with the European Union (EU) requirements defined in the EU-Directive on Waste. The new waste law updates were enacted into the Finnish legislation on the 11.03.2011 and targeted for applicability by the 11.03.2012. This thesis investigates the implications of the new amendments to the waste legislation from the perspective of green sand foundries. The investigations are conducted by comparing two of Componenta’s green sand foundries and evaluating their waste streams. Additionally, the impacts of legislation amendments are critiqued on their environmental and economic aspects. The study’s comparison of waste fractions at the two foundries reveals that sand is dominant in absolute tonnage and costs. The increments of waste taxes forces foundries to focus on waste management, recycling and disposing. The new legislation’s promotion of material efficiency, also guides foundries towards the prevention of waste. A potential preventive measure is to regenerate waste sand resulting to cost savings on both raw-materials and waste management. However, the lack of absolute targets for waste prevention or recycling rates discourages the interests towards creating or adopting new technologies and methods for the waste handling.

Liikennebiokaasun tuotannon ja käytön ulkoiset kustannukset Pohjois-Karjalassa

Työn tavoitteena oli selvittää liikennebiokaasuntuotannon ja käytön vaikutus liikenteen ulkoi-siin kustannuksiin Pohjois-Karjalassa. Biokaasua tuotetaan Joensuussa Kuhasalon jäteveden-puhdistamolla sekä Kontiosuon jäteasemalla, Kiteellä biokaasua tuotetaan BioKympin yh-teismädätyslaitoksessa. Lisäksi laskennassa huomioitiin yhden maatilakokoluokan biokaasun-tuotanto. Työssä selvitettiin kaksi skenaariota liikennebiokaasun tuotantomääräksi vuodelle 2015. Liikennebiokaasua voitaisiin tuottaa optimiskenaarion mukaan 3 426 MWh ja maksimi-tuotantoskenaarion mukaan 21 532 MWh. Liikennebiokaasun käytön vaikutukset liikenteen päästöihin laskettiin vuodelle 2015 ja vuo-delle 2020, jolloin liikennebiokaasua käytettäisiin 10 % liikenteen energiantarpeesta Pohjois-Karjalassa. Hiilidioksidipäästöt vähenevät vuoden 2020 tilanteessa samassa suhteessa kuin liikennebiokaasu korvaa fossiilisia polttoaineita. Muista päästöistä merkittävimmät päästövä-hennykset saatiin kun vuoden 2010 dieselautot muutettaisiin biokaasuautoiksi, tällöin hiuk-kaspäästöt alenisivat jopa 18 % vuoden 2010 päästöistä. Lisäksi selvitettiin liikenteen päästöjen pienenemisen vaikutus liikenteen aiheuttamiin ulkoisiin kustannuksiin. Laskettavat ulkoiset kustannukset olivat ilmastonmuutos, pakokaasupäästöt sekä energiariippuvuus. Pakokaasupäästöjen aiheuttamat ulkoiset kustannukset olivat vuonna 2010 noin 7 miljoonaa euroa. Liikennebiokaasua käyttävästä ajoneuvotyypistä riippuen ulkoiset kustannukset laskevat vuoden 2020 tilanteessa 10–16 % vuoden 2010 kustannuksista. Ilmastonmuutoksen ulkoiset kustannukset vuodelle 2010 olivat 9,5 miljoonaa euroa. Biokaasun käytön avulla kustannuksissa voitaisiin säästää 910 000 euroa vuonna 2020. Ener-giariippuvuuden hinta öljynkäytöstä oli vuonna 2010 noin 4,2 miljoonaa euroa ja vuonna 2020 kustannukset voisivat laskea 450 000 euroa.

Public-private partnership in marine litter waste management

Marine litter is an international environmental problem that causes considerable costs to coastal communities and the fishing industry. Several international and national treaties and regulations have provisions to marine litter and forbid disposal of waste into the sea. However, none of these regulations state a responsibility for public authorities to recover marine litter from the sea, like they do for marine litter that washes up on public beaches. In a financial evaluation of a value chain for marine litter incineration it was found out that the total costs of waste incineration are approximately 100 ─ 200 % higher than waste fees offered by waste contractors of ports. The high costs of incineration are derived from the high calorific value of marine litter and therefore a high incineration cost for the waste, and long distances between ports that are taking part in a project for marine litter recovery from the sea and an Energy-from-Waste (EfW) facility. This study provides a possible solution to diverting marine litter from landfills to more environmentally sustainable EfW use by using a public-private partnership (PPP) framework. PPP would seem to fit as a suitable cooperative approach for answering problems of current marine litter disposal in theory. In the end it is up to the potential partners of this proposed PPP to decide whether the benefits of cooperation justify the required efforts.

Current status of the waste-to-energy chain in the County of North Savo, Finland

The aim of this report is to describe the current status of the waste-to-energy chain in the province of Northern Savonia in Finland. This work is part of the Baltic Sea Region Programme project Remowe-Regional Mobilizing of Sustainable Waste-to-Energy Production (2009-2012). Partnering regions across Baltic Sea countries have parallelly investigated the current status, bottle-necks and needs for development in their regions. Information about the current status is crucial for the further work within the Remowe project, e.g. in investigating the possible future status in target regions. Ultimate result from the Northern Savonia point of view will be a regional model which utilizes all available information and facilitates decision-making concerning energy utilization of waste. The report contains information on among others: - waste management system (sources, amounts, infrastructure) - energy system (use, supply, infrastructure) - administrative structure and legislation - actors and stakeholders in the waste-to-energy field, including interest and development ideas The current status of the regions will be compared in a separate Remowe report, with the focus on finding best practices that could be transferred among the regions. In this report, the current status has been defined as 2006-2009. In 2009, the municipal waste amount per capita was 479 kg/inhabitant in Finland. Industrial waste amounted 3550 kg/inhabitant, respectively. The potential bioenergy from biodegradable waste amounts 1 MWh/inhabitant in Northern Savonia. This figure includes animal manure, crops that would be suitable for energy use, sludge from municipal sewage treatment plants and separately collected biowaste. A key strategy influencing also to Remowe work is the waste plan for Eastern Finland. Currently there operate two digestion plants in Northern Savonia: Lehtoniemi municipal sewage treatment sludge digestion plant of Kuopion Vesi and the farm-scale research biogas plant of Agrifood Research Finland in Maaninka. Moreover, landfill gas is collected to energy use from Heinälamminrinne waste management centre and Silmäsuo closed landfill site, both belonging to Jätekukko Oy. Currently there is no thermal utilization of waste in Northern Savonia region. However, Jätekukko Oy is pretreating mixed waste and delivering refuse derived fuel (RDF) to Southern Finland to combustion. There is a strong willingness among seven regional waste management companies in Eastern Finland to build a waste incineration plant to Riikinneva waste management centre near city of Varkaus. The plant would use circulating fluidized bed (CFB) boiler. This would been a clear boost in waste-to-energy utilization in Northern Savonia and in many surrounding regions.

Feasibility of ASH DEC‐ process in treating sewage sludge and manure ash in Finland

In Finland the thermal treatment of sewage sludge has been moderate in 21th century. The reason has been the high moisture content of sludge. During 2005-2008, 97-99% of sewage sludge was utilized in landscaping and agriculture. However agricultural use has been during 2005-2007 less than 3 %. The aim of national waste management plan is that by 2016 100% of sludge is used either as soil amendment or energy. The most popular utilization method for manure is spreading it on arable land. The dry manures such as poultry manure and horse manure could also be used in incineration. The ashes could be used as fertilizers and while it is not suitable as a starter fertilizer, it is suitable in maintaining P levels in the soil. One of the main drivers for more efficient nutrient management is the eutrophication in lakes and the Baltic See. ASH DEC process can be used in concentrating phosphorus rich ashes while separating the heavy metals that could be included. ASH DEC process uses thermochemical treatment to produce renewable phosphate for fertilizer production. The process includes mixing of ashes and chlorine donors and subsequent treatment in rotary kiln for 20 min in temperature of 900 – 1 050 oC. The heavy metals evaporate and P-rich product is obtained. The toxic substances are retained in air pollution control system in form of mixed metal hydroxides. The aim of conducting this study is to estimate the potential of ASH DEC process in treating phosphorus rich ashes in Finland. The masses considered in are sewage sludge, dry manure from horses, and poultry and liquid pig manure. To date the usual treatment method for sewage sludge in Finland is composting or anaerobic digestion. Part of the amount of produced sewage sludge (800 kt/a fresh mass and 160 kt/a TS) could also be incinerated and the residual ashes used in ASH DEC process. Incinerating only manure can be economically difficult to manage because the incineration of manure is in Finland considered as waste incineration. Getting a permit for waste incineration is difficult and also small scale waste incineration is too expensive. The manure could act as an additional feedstock in counties with high density of animal husbandry where the land area might not be enough for spreading of manure. Now when the manure acts as a supplementary feedstock beside sludge, the ash can’t be used directly as fertilizer. Then it could be used in ASH DEC process. The perquisite is that the manure producers could pay for the incineration, which might prove problematic.

Waste-to-Energy Scenarios in the China Context

Waste incineration plants are increasingly established in China. A low heating value and high moisture content, due to a large proportion of biowaste in the municipal solid waste (MSW), can be regarded as typical characteristics of Chinese MSW. Two incineration technologies have been mainly established in China: stoker grate and circular fluidized bed (CFB). Both of them are designed to incinerate mixed MSW. However, there have been difficulties to reach the sufficient temperature in the combustion process due to the low heating value of the MSW. That is contributed to the usage of an auxiliary fossil fuel, which is often used during the whole incineration process. The objective of this study was to design alternative Waste-to-energy (WTE) scenarios for existing WTE plants with the aim to improve the material and energy efficiency as well as the feasibility of the plants. Moreover, the aim of this thesis was to find the key factors that affect to the feasibility of the scenarios. Five different WTE plants were selected as study targets. The necessary data for calculation was gained from literature as well as received from the operators of the target WTE plants. The created scenarios were based on mechanical-biological treatment (MBT) technologies, in which the produced solid recovered fuel (SRF) was fed as an auxiliary fuel into a WTE plant replacing the fossil fuel. The mechanically separated biowaste was treated either in an anaerobic digestion (AD) plant, a biodrying plant, a thermal drying plant, or a combined AD plant + thermal drying plant. An interactive excel spreadsheet based computation tool was designed to estimate the viability of the scenarios in different WTE cases. The key figures of the improved material and energy efficiency, such as additional electricity generated and avoided waste for landfill, were got as results. Furthermore, economic indicators such as annual profits (or costs), payback period, and internal rate of return (IRR) were gained as results. The results show that the AD scenario was the most profitable in most of the cases. The current heating value of MSW and the tipping fee for the received MSW appeared as the most important factor in terms of feasibility.

Indoor air quality at a waste incineration plant in Finland

Waste has been incinerated for energy utilization for more than a hundred years, but the harmful emissions emitted from the incineration plants did not begin to cause concern until the 1980s. Many plants were shutdown and the waste incineration plant in Kyläsaari Helsinki was one of them. In later years, new landfill regulations have increased the interest in waste incineration. During the last year, four new plants were taken into operation in Finland, Westenergy in Vaasa among them. The presence of dust has been observed indoors at Westenergy waste incineration plant. Dust is defined as particles with a diameter above 10 μm, while fine particles have a diameter smaller than 2.5 μm, ultrafine under 0.1 μm and nanoparticles under 0.05 μm. In recent years, the focus of particle health research has been changed to investigate smaller particles. Ultrafine particles have been found to be more detrimental to health than larger particles. Limit values regulating the concentrations of ultrafine particles have not been determined yet. The objective of this thesis was to investigate dust and particles present inside the Westenergy waste incineration facility. The task was to investigate the potential pollutant sources and to give recommendations of how to minimize the presence of dust and particles in the power plant. The total particle number concentrations and size distributions where measured at 15 points inside the plant with an Engine Exhaust Particle Sizer (EEPS) Spectrometer. The measured particles were mainly in the ultrafine size range. Dust was only visually investigated, since the main purpose was to follow the dust accumulation. The measurement points inside the incineration plant were chosen according to investigate exposure to visitors and workers. At some points probable leakage of emissions were investigated. The measurements were carried out during approximately one month in March–April 2013. The results of the measurements showed that elevated levels of dust and particles are present in the indoor air at the waste incineration plant. The cleanest air was found in the control room, warehouse and office. The most polluted air was near the sources that were investigated due to possible leakage and in the bottom ash hall. However, the concentrations were near measured background concentrations in European cities and no leakage could be detected. The high concentrations were assumed to be a result of a lot of dust and particles present on surfaces that had not been cleaned in a while. The main source of the dust and particles present inside the waste incineration plant was thought to be particles and dust from the outside air. Other activities in the area around the waste incineration facility are ground work activities, stone crushing and traffic, which probably are sources of particle formation. Filtration of the outside air prior entering the facility would probably save personnel and visitors from nuisance and save in cleaning and maintenance costs.

Characterisation of waste for combustion : with special reference to the role of zinc

Waste combustion has gone from being a volume reducing discarding-method to an energy recovery process for unwanted material that cannot be reused or recycled. Different fractions of waste are used as fuel today, such as; municipal solid waste, refuse derived fuel, and solid recovered fuel. Furthermore, industrial waste, normally a mixture between commercial waste and building and demolition waste, is common, either as separate fuels or mixed with, for example, municipal solid waste. Compared to fossil or biomass fuels, waste mixtures are extremely heterogeneous, making it a complicated fuel. Differences in calorific values, ash content, moisture content, and changing levels of elements, such as Cl and alkali metals, are common in waste fuel. Moreover, waste contains much higher levels of troublesome trace elements, such as Zn, which is thought to accelerate a corrosion process. Varying fuel quality can be strenuous on the boiler system and may cause fouling and corrosion of heat exchanger surfaces. This thesis examines waste fuels and waste combustion from different angles, with the objective of giving a better understanding of waste as an important fuel in today’s fuel economy. Several chemical characterisation campaigns of waste fuels over longer time periods (10-12 months) was used to determine the fossil content of Swedish waste fuels, to investigate possible seasonal variations, and to study the presence of Zn in waste. Data from the characterisation campaigns were used for thermodynamic equilibrium calculations to follow trends and determine the effect of changing concentrations of various elements. The thesis also includes a study of the thermal behaviour of Zn and a full—scale study of how the bed temperature affects the volatilisation of alkali metals and Zn from the fuel. As mixed waste fuel contains considerable amounts of fresh biomass, such as wood, food waste, paper etc. it would be wrong to classify it as a fossil fuel. When Sweden introduced waste combustion as a part of the European Union emission trading system in the beginning of 2013 there was a need for combustion plants to find a usable and reliable method to determine the fossil content. Four different methods were studied in full-scale of seven combustion plants; 14Canalysis of solid waste, 14C-analysis of flue gas, sorting analysis followed by calculations, and a patented balance method that is using a software program to calculate the fossil content based on parameters from the plant. The study showed that approximately one third of the coal in Swedish waste mixtures has fossil origins and presented the plants with information about the four different methods and their advantages and disadvantages. Characterisation campaigns also showed that industrial waste contain higher levels of trace elements, such as Zn. The content of Zn in Swedish waste fuels was determined to be approximately 800 mg kg-1 on average, based on 42 samples of solid waste from seven different plants with varying mixtures between municipal solid waste and industrial waste. A review study of the occurrence of Zn in fuels confirmed that the highest amounts of Zn are present in waste fuels rather than in fossil or biomass fuels. In tires, Zn is used as a vulcanizing agent and can reach concentration values of 9600-16800 mg kg-1. Waste Electrical and Electronic Equipment is the second Zn-richest fuel and even though on average Zn content is around 4000 mg kg-1, the values of over 19000 mg kg-1 were also reported. The increased amounts of Zn, 3000-4000 mg kg-1, are also found in municipal solid waste, sludge with over 2000 mg kg-1 on average (some exceptions up to 49000 mg kg-1), and other waste derived fuels (over 1000 mg kg-1). Zn is also found in fossil fuels. In coal, the average level of Zn is 100 mg kg-1, the higher amount of Zn was only reported for oil shale with values between 20-2680 mg kg-1. The content of Zn in biomass is basically determined by its natural occurrence and it is typically 10-100 mg kg-1. The thermal behaviour of Zn is of importance to understand the possible reactions taking place in the boiler. By using thermal analysis three common Zn-compounds were studied (ZnCl2, ZnSO4, and ZnO) and compared to phase diagrams produced with thermodynamic equilibrium calculations. The results of the study suggest that ZnCl2(s/l) cannot exist readily in the boiler due to its volatility at high temperatures and its conversion to ZnO in oxidising conditions. Also, ZnSO4 decomposes around 680°C, while ZnO is relatively stable in the temperature range prevailing in the boiler. Furthermore, by exposing ZnO to HCl in a hot environment (240-330°C) it was shown that chlorination of ZnO with HCl gas is possible. Waste fuel containing high levels of elements known to be corrosive, for example, Na and K in combination with Cl, and also significant amounts of trace elements, such as Zn, are demanding on the whole boiler system. A full-scale study of how the volatilisation of Na, K, and Zn is affected by the bed temperature in a fluidised bed boiler was performed parallel with a lab-scale study with the same conditions. The study showed that the fouling rate on deposit probes were decreased by 20 % when the bed temperature was decreased from 870°C to below 720°C. In addition, the lab-scale experiments clearly indicated that the amount of alkali metals and Zn volatilised depends on the reactor temperature.

Importance of considering food waste in the development of sustainable food packaging systems

Meeting the needs of both present and future generations forms the foundation of sustainable development. Concern about food demand is increasing alongside the continuously growing population. In the pursuit of food security preventing food waste is one solution avoiding the negative environmental impacts that result from producing food unnecessarily. Packages offer one answer to preventing food waste, as they 1) preserve and protect food, 2) introduce the user to the correct way to handle and use the food and package and 3) allow the user to consume the food in its entirety. This thesis aims to enhance the sustainability of food packages by giving special emphasis to preventing food waste. The focus of this thesis is to assist the packaging designer in being able to take into account the requirements for the sustainability of food packages and to be able to integrate these requirements into the product development process. In addition, life cycle methods that can be used as a tool in the packaging design process or in assessing the sustainability of finished food-packaging combinations are evaluated. The methods of life cycle costing (LCC) and life cycle working environment (LCWE) are briefly discussed. The method of life cycle assessment (LCA) is examined more thoroughly through the lens of the literature review of food-package LCA case studies published in the 21st century in three relevant journals. Based on this review and on experiences learned from conducting LCAs, recommendations are given as to how the LCA practitioner should conduct a food packaging study to make most of the results. Two case studies are presented in this thesis. The first case study relates the results of a life cycle assessment conducted for three food items (cold cut (ham), sliced dark bread (rye) and Soygurt drink) and the alternative packaging options of each. Results of this study show that the packaging constitutes only 1–12 % of the total environmental impacts of the food-packaging combination. The greatest effect is derived from the food itself and the wasted food. Even just a small percentage of wasted food causes more environmental impacts than does the packaging. The second case study presents the results of LCC and LCWE analysis done for fruit and vegetable transport packages. In this thesis, the specific results of the study itself are not the focus, but rather the study methods and scope are analysed based on how these complement the sustainability assessment of food packages. This thesis presents reasons why prevention of food waste should be more thoroughly taken into account in food packaging design. In addition, the task of the packaging designer is facilitated by the requirements of sustainable food packaging, by the methods and step-by-step guidance on how to integrate sustainability issues into the design process, and by the recommendations on how to assess the sustainability of food packages. The intention of this thesis is to express the issues that are important in the field of the food packaging industry. Having recognised and implemented these issues, businesses can better manage the risks that could follow from neglecting these sustainability aspects.

Industrial-Scale hydrothermal carbonization of waste sludge materials for fuel production

Hydrothermal carbonization (HTC) is a thermochemical process used in the production of charred matter similar in composition to coal. It involves the use of wet, carbohydrate feedstock, a relatively low temperature environment (180 °C-350 °C) and high autogenous pressure (up to 2,4 MPa) in a closed system. Various applications of the solid char product exist, opening the way for a range of biomass feedstock materials to be exploited that have so far proven to be troublesome due to high water content or other factors. Sludge materials are investigated as candidates for industrial-scale HTC treatment in fuel production. In general, HTC treatment of pulp and paper industry sludge (PPS) and anaerobically digested municipal sewage sludge (ADS) using existing technology is competitive with traditional treatment options, which range in price from EUR 30-80 per ton of wet sludge. PPS and ADS can be treated by HTC for less than EUR 13 and 33, respectively. Opportunities and challenges related to HTC exist, as this relatively new technology moves from laboratory and pilot-scale production to an industrial scale. Feedstock materials, end-products, process conditions and local markets ultimately determine the feasibility of a given HTC operation. However, there is potential for sludge materials to be converted to sustainable bio-coal fuel in a Finnish context.