Business Development Efforts and Performance Improvements in SMEs Case Study of Business Development Projects Implemented in SME

Under the circumstances of the increasing market pressure, enterprises try to improve their competitive position by development efforts, and a business development project is one tool for that. There are not many answers to the question of how the development projects launched to improve the business performance in SMEs have succeeded. Theacademic interest in the business development project success has mainly focused on projects implemented in larger organisations rather than in SMEs. The previous studies on the business success of SMEs have mainly focused on new business ventures rather than on existing SMEs. However, nowadays a large number of business development projects are undertaken in existing SMEs, where they can pose a great challenge. This study focuses on business development success in SMEs thathave already established their business. The objective of the present study is to gain a deep understanding on business development project success in the SME-context and to identify the dimensions and factors affecting the project success. Further, the aim is to clarify how the business development projects implemented in SMEs have affected their performance. The empirical evidence is based on multiple case study. This study builds a framework for a generic theory of business development success in the SME-context, based on literature from the areas ofproject and change management, entrepreneurship and small business management, as well as performance measurement, and on empirical evidence from SMES. The framework consists of five success dimensions: entrepreneurial, project preparation, change management, project management and project success. The framework provides a systematic way for analysing the business development project and its impact on the performance and on the performing company. This case evidence indicates that successful business development projects have a balanced, high performance concerning all the dimensions. Good performance in one dimension is not enoughfor the project success, but it gives a good ground for the other dimensions. The other way round, poor performance in one success dimension affects the others, leading to poor performance of the project. In the SME-context the business development project success seems to be dependent on several interrelated dimensions and factors. Success in one area leads to success in other areas, and so creates an upward success spiral. Failure in one area seems to lead to failure in other areas, creating a downward failure spiral. The study indicates that the internal business development projects have affected the SMEs' performance widely also on areas and functions not initially targeted. The implications cover all thesuccess categories: the project efficiency, the impact on the customer, the business success and the future potentiality. With successful cases, the success tends to spread out to areas and functions not mentioned as the project goals, andwith unsuccessful cases the failure seems to spread out widely to the SMEs' other functions. This study also indicates that the most important key factors for successful business development project implementation are the strength of intention, business ability, knowledge, motivation and participation of the employees, as well as adequate and well-timed training provided to the employees.

Innovation Benchmark Study: Analysis of Innovation Processes in Finnish Companies

Liikevaihdon orgaaninen kasvu on ensisijainen tekijä ja haaste yritysjohdolle yrityksen omistaja-arvon kasvattamiseksi. Tutkimus tarkastelee suosivatko suomalaisyritykset pääasiallisesti olemassa olevaa liiketoimintaa palvelevia innovaatioita vai tukevatko nykyhetken toimintatavat myös uusia kasvua kiihdyttäviä radikaaleja innovaatioita. Lisäksi työ kartoitti suomalaisyritysten innovaatioprosessien kehitysalueita käyttäen itsearviointitutkimusta.Tulokset johtivat kolmeen johtopäätökseen. Tutkimus osoitti, että vastaajayritykset ovat keskittyneet innovaatiotoiminnassaan vahvasti ydinliiketoimintaansa, jättäen potentiaaliset kasvumahdollisuudet huomioimatta. Yritykset tavoittelevat maksimaalisia tuottoja keskittymällä tuotteidensa korkeaan suorituskykyyn. Lyhyen aikavälin epärealistiset tuotto-odotukset sekä projekteille suunnatut arviointikriteerit rajoittavat liiketoimintaa mullistavien radikaalien innovaatioiden kehittymistä organisaatiossa. Toiseksi, tutkimus osoitti, että suuri osa yrityksistä käyttää perinteisen projektien arviointi- ja kehitysprosessin lisäksi vaihtoehtoisia ja huonosti kontrolloitavissa olevia kehitysprosesseja, mikäli projektille annetaan kielteinen rahoituspäätös standardin prosessin sisällä. Kolmanneksi, suomalaisyritysten innovaatioprosesseissa paljastui merkittäviä puutteita mitattavien elementtien suhteen.

A Feasibility Study of a Pelleting Plant as an Option for By Product Upgrading in Wood-Processing Industry

Tämän kannattavuustutkimuksen lähtökohtana oli se, että Yhtyneet Sahat Oy:n Kaukaan sahalla ja Luumäen jatkojalostuslaitoksella haluttiin selvittää pellettitehtaan kannattavuus nykyisessä markkinatilanteessa. Tämä työon luonteeltaan teknis-taloudellinen selvitys eli ns. feasibility study. Pelletöintiprosessi on tekniikaltaan yksinkertainen eikä edellytä korkea teknologian laitteita. Toimiala on maailmanlaajuisesti varsin uusi. Suomessa pellettimarkkinat ovat vielä pienet ja kehittymättömät, mutta kasvua on viime vuosina tapahtunut. Valtaosa kotimaan tuotannosta menee vientiin. Investoinnin laskentaprosessissa saadut tuotannon alkuarvot sekä kustannusrakenteen määrittelyt ovat perustana varsinaisille kannattavuuslaskelmille. Laskelmista on selvitetty investointeihin liittyvät yleisimmät taloudelliset tunnusluvut ja herkimpiä muuttujia on tutkittu ja pohdittu herkkyysanalyysiä apuna käyttäen.

Development of aBuyer-Supplier Relationship: Case Study of Radical Shifts in Key Account Relationships

Tämän tutkimuksen tavoitteena oli tutkia ja selvittää monimutkaisia myyjän ja toimittajan välisiä liikesuhteita; miten ne kehittyvät ja millaisia prosesseja ne käyvät läpi, jos avainasiakassuhde on vaikeuksissa. Tavoitteena oli myös löytää syitä miksi ostokäyttäytyminen on muuttunut, onko se maailman- laajuinen ilmiö vai onko kyse vain yksittäisestä tapauksesta paperiteolli-suudessa. Lisäksi tavoitteena oli selvittää mitkä ovat alkusysäyksiä avain-asiakassuhteen murrostilaan. Tutkimuksen lähestymistapa on kvalitatiivinen tapaustutkimus. Tutkimuksen ensisijainen empiirinen aineisto on kerätty haastattelemalla UPM-Kymmenen johtoa, paperin osto-organisaation ostojohtajaa X ja asiakas Y:n entistä osto-johtajaa. Työ ei ole salainen. Tämän takia asiakkaiden nimiä ei voida julkaista, koska UPM-Kymmene vaati, että työ ei saa sisältää mitään informaatiota, josta lukija voi tunnistaa asiakas X:n tai Y:n. Johtopäätöksenä voidaan suosittaa toimittajan tarkkailevan ja ymmärtävän mahdollisia alkusysäyksiä ja varoitussignaaleja ehkäistäkseen tulevaisuuden murrostiloja liikesuhteissaan ja hallita paremmin avainasiakkaitaan.Pääasialliset alkusysäykset ovat vähentynyt avoin kommunikaatio, ostajan radikaalit säästöt, vähentynyt informaation vaihto ja ostajan johdon vaihtuminen, koska se luo epävarmuutta toimittajaan kuten myös ostajaan.

On the innovation capacity of technologyrelated knowledge-intensive business services. A case study of the technology and engineering consulting (TEC) sector in Singapore

Even though the research on innovation in services has expanded remarkably especially during the past two decades, there is still a need to increase understanding on the special characteristics of service innovation. In addition to studying innovation in service companies and industries, research has also recently focused more on services in innovation, as especially the significance of so-called knowledge intensive business services (KIBS) for the competitive edge of their clients, othercompanies, regions and even nations has been proved in several previous studies. This study focuses on studying technology-based KIBS firms, and technology andengineering consulting (TEC) sector in particular. These firms have multiple roles in innovation systems, and thus, there is also a need for in-depth studies that increase knowledge about the types and dimensions of service innovations as well as underlying mechanisms and procedures which make the innovations successful. The main aim of this study is to generate new knowledge in the fragmented research field of service innovation management by recognizing the different typesof innovations in TEC services and some of the enablers of and barriers to innovation capacity in the field, especially from the knowledge management perspective. The study also aims to shed light on some of the existing routines and new constructions needed for enhancing service innovation and knowledge processing activities in KIBS companies of the TEC sector. The main samples of data in this research include literature reviews and public data sources, and a qualitative research approach with exploratory case studies conducted with the help of the interviews at technology consulting companies in Singapore in 2006. These complement the qualitative interview data gathered previously in Finland during a larger research project in the years 2004-2005. The data is also supplemented by a survey conducted in Singapore. The respondents for the survey by Tan (2007) were technology consulting companies who operate in the Singapore region. The purpose ofthe quantitative part of the study was to validate and further examine specificaspects such as the influence of knowledge management activities on innovativeness and different types of service innovations, in which the technology consultancies are involved. Singapore is known as a South-east Asian knowledge hub and is thus a significant research area where several multinational knowledge-intensive service firms operate. Typically, the service innovations identified in the studied TEC firms were formed by several dimensions of innovations. In addition to technological aspects, innovations were, for instance, related to new client interfaces and service delivery processes. The main enablers of and barriers to innovation seem to be partly similar in Singaporean firms as compared to the earlier study of Finnish TEC firms. Empirical studies also brought forth the significance of various sources of knowledge and knowledge processing activities as themain driving forces of service innovation in technology-related KIBS firms. A framework was also developed to study the effect of knowledge processing capabilities as well as some moderators on the innovativeness of TEC firms. Especially efficient knowledge acquisition and environmental dynamism seem to influence the innovativeness of TEC firms positively. The results of the study also contributeto the present service innovation literature by focusing more on 'innovation within KIBs' rather than 'innovation through KIBS', which has been the typical viewpoint stressed in the previous literature. Additionally, the study provides several possibilities for further research.

The effects of potentiallydisruptive technology on business model - a case study of new technologies in ICT industry

This study examines how firms interpret new, potentially disruptive technologies in their own strategic context. The work presents a cross-case analysis of four potentially disruptive technologies or technical operating models: Bluetooth, WLAN, Grid computing and Mobile Peer-to-peer paradigm. The technologies were investigated from the perspective of three mobile operators, a device manufacturer and a software company in the ICT industry. The theoretical background for the study consists of the resource-based view of the firm with dynamic perspective, the theories on the nature of technology and innovations, and the concept of business model. The literature review builds up a propositional framework for estimating the amount of radical change in the companies' business model with two middle variables, the disruptiveness potential of a new technology, and the strategic importance of a new technology to a firm. The data was gathered in group discussion sessions in each company. The results of each case analysis were brought together to evaluate, how firms interpret the potential disruptiveness in terms of changes in product characteristics and added value, technology and market uncertainty, changes in product-market positions, possible competence disruption and changes in value network positions. The results indicate that the perceived disruptiveness in terms ofproduct characteristics does not necessarily translate into strategic importance. In addition, firms did not see the new technologies as a threat in terms of potential competence disruption.

A comparative performance study of four-pole induction motors and synchronous reluctance motors in variable speed drives

Design aspects of the Transversally Laminated Anisotropic (TLA) Synchronous Reluctance Motor (SynRM) are studied and the machine performance analysis compared to the Induction Motor (IM) is done. The SynRM rotor structure is designed and manufactured for a30 kW, four-pole, three-phase squirrel cage induction motor stator. Both the IMand SynRM were supplied by a sensorless Direct Torque Controlled (DTC) variablespeed drive. Attention is also paid to the estimation of the power range where the SynRM may compete successfully with a same size induction motor. A technicalloss reduction comparison between the IM and SynRM in variable speed drives is done. The Finite Element Method (FEM) is used to analyse the number, location and width of flux barriers used in a multiple segment rotor. It is sought for a high saliency ratio and a high torque of the motor. It is given a comparison between different FEM calculations to analyse SynRM performance. The possibility to take into account the effect of iron losses with FEM is studied. Comparison between the calculated and measured values shows that the design methods are reliable. A new application of the IEEE 112 measurement method is developed and used especially for determination of stray load losses in laboratory measurements. The study shows that, with some special measures, the efficiency of the TLA SynRM is equivalent to that of a high efficiency IM. The power factor of the SynRM at rated load is smaller than that of the IM. However, at lower partial load this difference decreases and this, probably, brings that the SynRM gets a better power factor in comparison with the IM. The big rotor inductance ratio of the SynRM allows a good estimating of the rotor position. This appears to be very advantageous for the designing of the rotor position sensor-less motor drive. In using the FEM designed multi-layer transversally laminated rotor with damper windings it is possible to design a directly network driven motor without degrading the motorefficiency or power factor compared to the performance of the IM.

Theoretical and numerical study of thermomagnetic convection in magnetic fluids

In this thesis, the magnetic field control of convection instabilities and heat and mass transfer processesin magnetic fluids have been investigated by numerical simulations and theoretical considerations. Simulation models based on finite element and finite volume methods have been developed. In addition to standard conservation equations, themagnetic field inside the simulation domain is calculated from Maxwell equations and the necessary terms to take into account for the magnetic body force and magnetic dissipation have been added to the equations governing the fluid motion.Numerical simulations of magnetic fluid convection near the threshold supportedexperimental observations qualitatively. Near the onset of convection the competitive action of thermal and concentration density gradients leads to mostly spatiotemporally chaotic convection with oscillatory and travelling wave regimes, previously observed in binary mixtures and nematic liquid crystals. In many applications of magnetic fluids, the heat and mass transfer processes including the effects of external magnetic fields are of great importance. In addition to magnetic fluids, the concepts and the simulation models used in this study may be applied also to the studies of convective instabilities in ordinary fluids as well as in other binary mixtures and complex fluids.

CFD study of penetration and mixing of fuel in a circulating fluidized bed furnace

The aim of this thesis is to study the mixing of fuel and, also to some extent, the mixing of air in a circulating fluidized bed boiler. In the literature survey part of this thesis, a review is made of the previous experimental studies related to the fuel and air mixing in the circulating fluidized beds. In the simulation part of it the commercial computational fluid dynamics software (FLUENT) is used with the Eulerian multiphase model for studying the fuel mixing in the two and three-dimensional furnace geometries. The results of the three-dimensional simulations are promising and, therefore suggestions are made for the future simulations. The two-dimensional studies give new information of the effects of the fluidization velocity, fuel particle size and fuel density on the fuel mixing. However, the present results show that three-dimensional models produce more realistic representation of the circulating fluidized bed behavior.

Animals in an Urban Context. A Zooarchaeological study of the Medieval and Post-Medieval town of Turku

The aim of this study is to explore the role and importance of different animal species in Turku through an analysis of osteological data and documentary evidence. The osteological material used in this study is derived from two town plots in Turku dating from the 13th century to the 19th century. The osteological material deposited in Turku represents animals bred both in the town and in the surrounding landscape. Animal husbandry in SW-Finland can also be examined through a number of historical documents. The importance of animals in Turku and its hinterland are closely connected and therefore the roles of the animals in both urban and rural settings are examined. The study has revealed the complexity of the depositional patterns in medieval and post-medieval Turku. In the different areas of Turku, characteristic patterns in the osteological material and different deposit types were evident. These patterns are reflections of the activities and therefore of the lifestyles practiced in Turku. The results emphasise the importance of context- awareness in the study of material culture from archaeological sites. Both the zooarchaeological and historical sources indicate that cattle were important in animal husbandry in Turku from the Middle Ages up to the 19th century. Sheep were the second most common species. When taking into consideration the larger size of cattle, the dominance of these animals when it come to meat consumption seems clear even in those phases where sheep bones are more abundant. Pig is less abundant in the material than either cattle or sheep and their importance for subsistence was probably fairly modest, albeit constant. Goats were not abundant in the material. Most of the identified goat bones came from low utility body parts (e.g. skulls and lower extremities), but some amount of goat meat was also consumed. Wild species were of minor importance when it came to consumption practices in Turku. The changes in Turku’s animal husbandry patterns between the medieval and post medieval periods is reflected in the change in age of the animals slaughtered, which was part of a wider pattern seen in North- and Central Europe. More mature animals are also present in the assemblages. This pattern is related to the more pronounced importance of cattle as a manure producer and a draught animal as a result of the intensification of crop cultivation. This change seems to occur later in Finland than in the more Southerly regions, and indeed it did not necessarily take hold in all parts of the country.

Profiles of Second Language Learners in Bilingual Education: A Comparative Study of the Characteristics of Finnish and American Students

The purpose of this comparative study is to profile second language learners by exploring the factors which have an impact on their learning. The subjects come from two different countries: one group comes from Milwaukee, US, and the other from Turku, Finland. The subjects have attended bilingual classes from elementary school to senior high school in their respective countries. In the United States, the subjects (N = 57) started in one elementary school from where they moved on to two high schools in the district. The Finnish subjects (N = 39) attended the same school from elementary to high school. The longitudinal study was conducted during 1994-2004 and combines both qualitative and quantitative research methods. A Pilot Study carried out in 1990-1991 preceded the two subsequent studies that form the core material of this research. The theoretical part of the study focuses first on language policies in the United States and Finland: special emphasis is given to the history, development and current state of bilingual education, and the factors that have affected policy-making in the provision of language instruction. Current language learning theories and models form the theoretical foundation of the research, and underpin the empirical studies. Cognitively-labeled theories are at the forefront, but sociocultural theory and the ecological approach are also accounted for. The research methods consist of questionnaires, compositions and interviews. A combination of statistical methods as well as content analysis were used in the analysis. The attitude of the bilingual learners toward L1 and L2 was generally positive: the subjects enjoyed learning through two languages and were motivated to learn both. The knowledge of L1 and parental support, along with early literacy in L1, facilitated the learning of L2. This was particularly evident in the American subject group. The American subjects’ L2 learning was affected by the attitudes of the learners to the L1 culture and its speakers. Furthermore, the negative attitudes taken by L1 speakers toward L2 speakers and the lack of opportunities to engage in activities in the L1 culture affected the American subjects’ learning of L2, English. The research showed that many American L2 learners were isolated from the L1 culture and were even afraid to use English in everyday communication situations. In light of the research results, a politically neutral linguistic environment, which the Finnish subjects inhabited, was seen to be more favorable for learning. The Finnish subjects were learning L2, English, in a neutral zone where their own attitudes and motivation dictated their learning. The role of L2 as a means of international communication in Finland, as opposed to a means of exercising linguistic power, provided a neutral atmosphere for learning English. In both the American and Finnish groups, the learning of other languages was facilitated when the learner had a good foundation in their L1, and the learning of L1 and L2 were in balance. Learning was also fostered when the learners drew positive experiences from their surroundings and were provided with opportunities to engage in activities where L2 was used.

A three dimensional study of heat transfer in a supercritical circulating fluidized bed combustor

From the boiler design point of view, it is imperative to know and understand the operation of the boiler. Since comprehensive measurement of a large furnace is impossible, the furnace can be modeled in order to study its behavior and phenomena. This requires the used model to be validated to correspond with the physical furnace behavior. In this thesis, a three dimensional furnace model is validated to match a bituminous coal utilizing, supercritical once-through circulating fluidized bed combustor based on measurement data. The validated model is used for analyzing the furnace heat transfer. Other heat transfer analysis methods are energy balance method based on tube surface temperature measurements and a method based on measured temperature difference between the tube crest and the fin. The latter method was developed in the thesis using Fluent-software. In the theory part, literature is reviewed and the fundamental aspects of circulating fluidized bed are discussed. These aspects are solid particle behavior in fluidization known as hydrodynamics, behavior of fuel and combustion and heat transfer. Fundamental aspects of modeling are also presented.

Groupware and Workflow Tools - A Case study of SAP Business Workflow Supporting System Integration in a Global Telecommunication Company

Workflow management systems aim at the controlled execution of complex application processes in distributed and heterogeneous environments. These systems will shape the structure of information systems in business and non-business environments. E business and system integration is a fertile soil for WF and groupware tools. This thesis aims to study WF and groupware tools in order to gather in house knowledge of WF to better utilize WF solutions in future, and to focus on SAP Business Workflow in order to find a global solution for Application Link Enabling support for system integration. Piloting this solution in Nokia collects the experience of SAP R/3 WF tool for other development projects in future. The literary part of this study will guide to the world of business process automation providing a general description of the history, use and potentials of WF & groupware software. The empirical part of this study begins with the background of the case study describing the IT environment initiating the case by introducing SAP R/3 in Nokia, the communication technique in use and WF tool. Case study is focused in one solution with SAP Business Workflow. This study provides a concept to monitor communication between ERP systems and to increase the quality of system integration. Case study describes a way create support model for ALE/EDI interfaces. Support model includes monitoring organization and the workflow processes to solve the most common IDoc related errors.

An experimental and theoretical study of multiphase flow in a circulating fluidized bed

A systematic averaging procedure has been derived in order to obtain an integral form of conservation equations for dispersed multiphase flow, especially applicable to fluidized beds. A similar averaging method is applied further to formulate macroscopic integral equations, which can be used in one-dimensional and macroscopic multi dimensional models. Circulating fluid bed hydrodynamics has been studied experimentally and both macroscopic and microscopic flow profiles have been measured in a cold model. As an application of the theory, the one dimensional model has been used to study mass and momentum conservation of gas and solid in a circulating fluid bed. Axial solid mixing has also been modelled by the one dimensional model and mixing parameters have been evaluated.