Design of axial-flux permanent-magnet low-speed machines and performance comparison between radial-flux and axial-flux machines

This thesis presents an alternative approach to the analytical design of surface-mounted axialflux permanent-magnet machines. Emphasis has been placed on the design of axial-flux machines with a one-rotor-two-stators configuration. The design model developed in this study incorporates facilities to include both the electromagnetic design and thermal design of the machine as well as to take into consideration the complexity of the permanent-magnet shapes, which is a typical requirement for the design of high-performance permanent-magnet motors. A prototype machine with rated 5 kW output power at 300 min-1 rotation speed has been designed and constructed for the purposesof ascertaining the results obtained from the analytical design model. A comparative study of low-speed axial-flux and low-speed radial-flux permanent-magnet machines is presented. The comparative study concentrates on 55 kW machines with rotation speeds 150 min-1, 300 min-1 and 600 min-1 and is based on calculated designs. A novel comparison method is introduced. The method takes into account the mechanical constraints of the machine and enables comparison of the designed machines, with respect to the volume, efficiency and cost aspects of each machine. It is shown that an axial-flux permanent-magnet machine with one-rotor-two-stators configuration has generally a weaker efficiency than a radial-flux permanent-magnet machine if for all designs the same electric loading, air-gap flux density and current density have been applied. On the other hand, axial-flux machines are usually smaller in volume, especially when compared to radial-flux machines for which the length ratio (axial length of stator stack vs. air-gap diameter)is below 0.5. The comparison results show also that radial-flux machines with alow number of pole pairs, p < 4, outperform the corresponding axial-flux machines.

A modified structural stress method for fatigue assessment of welded structures

Fatigue life assessment of weldedstructures is commonly based on the nominal stress method, but more flexible and accurate methods have been introduced. In general, the assessment accuracy is improved as more localized information about the weld is incorporated. The structural hot spot stress method includes the influence of macro geometric effects and structural discontinuities on the design stress but excludes the local features of the weld. In this thesis, the limitations of the structural hot spot stress method are discussed and a modified structural stress method with improved accuracy is developed and verified for selected welded details. The fatigue life of structures in the as-welded state consists mainly of crack growth from pre-existing cracks or defects. Crack growth rate depends on crack geometry and the stress state on the crack face plane. This means that the stress level and shape of the stress distribution in the assumed crack path governs thetotal fatigue life. In many structural details the stress distribution is similar and adequate fatigue life estimates can be obtained just by adjusting the stress level based on a single stress value, i.e., the structural hot spot stress. There are, however, cases for which the structural stress approach is less appropriate because the stress distribution differs significantly from the more common cases. Plate edge attachments and plates on elastic foundations are some examples of structures with this type of stress distribution. The importance of fillet weld size and weld load variation on the stress distribution is another central topic in this thesis. Structural hot spot stress determination is generally based on a procedure that involves extrapolation of plate surface stresses. Other possibilities for determining the structural hot spot stress is to extrapolate stresses through the thickness at the weld toe or to use Dong's method which includes through-thickness extrapolation at some distance from the weld toe. Both of these latter methods are less sensitive to the FE mesh used. Structural stress based on surface extrapolation is sensitive to the extrapolation points selected and to the FE mesh used near these points. Rules for proper meshing, however, are well defined and not difficult to apply. To improve the accuracy of the traditional structural hot spot stress, a multi-linear stress distribution is introduced. The magnitude of the weld toe stress after linearization is dependent on the weld size, weld load and plate thickness. Simple equations have been derived by comparing assessment results based on the local linear stress distribution and LEFM based calculations. The proposed method is called the modified structural stress method (MSHS) since the structural hot spot stress (SHS) value is corrected using information on weld size andweld load. The correction procedure is verified using fatigue test results found in the literature. Also, a test case was conducted comparing the proposed method with other local fatigue assessment methods.

Measuring irregularities and surface defects from printed patterns

Quality inspection and assurance is a veryimportant step when today's products are sold to markets. As products are produced in vast quantities, the interest to automate quality inspection tasks has increased correspondingly. Quality inspection tasks usuallyrequire the detection of deficiencies, defined as irregularities in this thesis. Objects containing regular patterns appear quite frequently on certain industries and science, e.g. half-tone raster patterns in the printing industry, crystal lattice structures in solid state physics and solder joints and components in the electronics industry. In this thesis, the problem of regular patterns and irregularities is described in analytical form and three different detection methods are proposed. All the methods are based on characteristics of Fourier transform to represent regular information compactly. Fourier transform enables the separation of regular and irregular parts of an image but the three methods presented are shown to differ in generality and computational complexity. Need to detect fine and sparse details is common in quality inspection tasks, e.g., locating smallfractures in components in the electronics industry or detecting tearing from paper samples in the printing industry. In this thesis, a general definition of such details is given by defining sufficient statistical properties in the histogram domain. The analytical definition allowsa quantitative comparison of methods designed for detail detection. Based on the definition, the utilisation of existing thresholding methodsis shown to be well motivated. Comparison of thresholding methods shows that minimum error thresholding outperforms other standard methods. The results are successfully applied to a paper printability and runnability inspection setup. Missing dots from a repeating raster pattern are detected from Heliotest strips and small surface defects from IGT picking papers.

Procurement in Project Implementation

Tutkimus keskittyy hankintatoimen kehittämiseen osana laitosprojektien toteutusta. Työ pohjautuu empiiriseltä taustaltaan Pöyry Oyj:n projektiliiketoimintaan ja työn tarkastelunäkökulmaksi onvalittu projektihallinnosta vastaavan yrityksen näkökulma. Tutkimus on hyvin käytännönläheinen ¿ se lähtee hankinnan ja sen seurannan ongelmista ja pyrkii tarjoamaan niihin uudenlaisia ratkaisuja. Pohjimmiltaan tutkimus kuuluu teollisuustalouden piiriin, vaikka tietojärjestelmätieteellä on vahva tukirooli. Työn tavoitteet ja tulokset liittyvät teollisuustaloudelle ominaisesti yrityksen toiminnan kehittämiseen, käytetyt välineet ja ratkaisut puolestaan hyödyntävät tietojärjestelmätieteen antamia mahdollisuuksia. Tutkimuksessa on käytetty konstruktiivista tutkimusotetta, jonka mukaisesti on luotu innovatiivisia konstruktioita ratkaisemaan aitoja reaalimaailman ongelmia ja tätä kautta tuotettu kontribuutioita teollisuustaloudelle. Tavoitteena oli järjestää hankintatoimi ja sen seuranta suurissa laitosprojekteissa tehokkaammin. Tätä varten uudistettiin ensin projektihallinnon ja hankintatoimen toimintaohjeet vastaamaan paremmin nykyajan vaatimuksia. Toimintaohjeiden perusteella ryhdyttiin toteuttamaan hankintaohjelmistoa, joka pystyisi kattamaan kaikki toimintaohjeissa kuvatut piirteet. Lopulta hankintaohjelmisto toi mukanaan uusia piirteitä projektihallintoon ja hankintatoimeen ja nämä sisällytettiin toimintaohjeisiin. Tähän kehitystyöhön ryhdyttiin, jotta laitosprojektien projektihallinto ja hankintatoimi toimisivat paremmin, eli pienemmin kustannuksin tuottaen projekteissa tarvittavat tulokset nopeammin, tarkemmin ja laadukkaammin. Tutkimuksella on kolmenlaisia tuloksia: hankintatoimen parannetut metodit, hankintaohjelmiston pohjana olevat toiminta- ja laskentamallit sekä implementaationa hankintasovellus. Uudistetut projekti- ja hankintaohjeet kuvaavat hankintatoiminnan parannettuja metodeja. Hankintaohjelmistoasuunnitellessa ja kehitettäessä tehdyt kuvaukset sisältävät uusia malleja niin hankintaprosessille kuin hankinnan seuraamiseksi suurissa laitosprojekteissa. Itse ohjelmisto on tuloksena implementaatio, joka perustuu parannettuihin hankintametodeihin ja uusiin toiminta- ja laskentamalleihin. Uudistetut projekti- ja hankintaohjeet ovat olleet käytössä Pöyry Oyj:ssä vuodesta 1991. Vuosien varrella nämä toimintaohjeet ovat auttaneet ja tukeneet satojen laitosprojektientoteutusta ja ylläpitäneet Pöyry Oyj:n kilpailukykyä kansainvälisenä projektitalona. Hankintasovellus puolestaan on ollut käytössä useissa projekteissa ja sen on havaittu pienentävän hankintatoimen suoria työkustannuksia laitosprojekteissa. Sovelluksen katsotaan myös tuovan epäsuoria kustannussäästöjä parempien hankintapäätösten muodossa, mutta näiden säästöjen suuruutta ei pystytä luotettavasti arvioimaan.

Analysis of the voltage source inverter with small DC-link capacitor

IIn electric drives, frequency converters are used to generatefor the electric motor the AC voltage with variable frequency and amplitude. When considering the annual sale of drives in values of money and units sold, the use of low-performance drives appears to be in predominant. These drives have tobe very cost effective to manufacture and use, while they are also expected to fulfill the harmonic distortion standards. One of the objectives has also been to extend the lifetime of the frequency converter. In a traditional frequency converter, a relatively large electrolytic DC-link capacitor is used. Electrolytic capacitors are large, heavy and rather expensive components. In many cases, the lifetime of the electrolytic capacitor is the main factor limiting the lifetime of the frequency converter. To overcome the problem, the electrolytic capacitor is replaced with a metallized polypropylene film capacitor (MPPF). The MPPF has improved properties when compared to the electrolytic capacitor. By replacing the electrolytic capacitor with a film capacitor the energy storage of the DC-linkwill be decreased. Thus, the instantaneous power supplied to the motor correlates with the instantaneous power taken from the network. This yields a continuousDC-link current fed by the diode rectifier bridge. As a consequence, the line current harmonics clearly decrease. Because of the decreased energy storage, the DC-link voltage fluctuates. This sets additional conditions to the controllers of the frequency converter to compensate the fluctuation from the supplied motor phase voltages. In this work three-phase and single-phase frequency converters with small DC-link capacitor are analyzed. The evaluation is obtained with simulations and laboratory measurements.

Careers of Managers, Comparison between ICT and Paper Business Sectors

The purpose of this study is to increase understanding of how the managers build their early career in information and communication technology industry (ICT business sector) and pulp- and paper industry (paper business sector). The focus of the study is to explore the importance differing a business sectors have in influencing managerial careers. Business sectors can affect careers in several ways.Sectors have different history and traditions. Also the age structure of ICT personnel differs from the age structure of personnel in the paper industry. Managers in the ICT and paper sector are technically educated but in different disciplines. Differences exist also in ways of recruiting and developing commitment inpersonnel. The target group of this research, middle management engineering personnel, work in Finnish ICT and paper companies. Research data were gathered in April-December 2002 in South-Karelia by interviewing 30 managers and six directors working in three Finnish ICT companies and in three paper companies. The research issue is approached on two levels: the individual level and the organizational level. The managers related their career stories in focused interviews. Directors, representing the organizations, described the generalities of the business sector and gave background information on company policies, human relationshippractices, as well as career and human resource development. Results of the study contribute to research discussions of career, life-span reasoning, socialization and commitment. Career is conceived as a series of positions including everykind of hierarchical mobility and all kinds of positions in work. A manager's career develops in interaction with the organization and it can be seen as involving a socializing process in an organization as a consequence of experiences andchanges in positions. This research contributes to the understanding of the nature of career in the context of two business sectors. Universal career theories,for the most part, do not perceive the importance of business sector in determining career experience. This study concentrates on describing and understanding early careers in two different business areas, elements committing managers to particular business sectors and the actions of companies in that particular sector. While career research began in the middle of 1950s, the theoretical basis of career research seems to be quite fragmented still. However, a dichotomy is consistently presented between traditional, hierarchical career research and boundaryless career thinking. In this research we examine how these old and new career concepts are evidence in the ICT and paper sectors. Careers are changing from formal, hierarchy-based structures to more fluid arrangements. The new boundaryless career concept captures territory from old career thinking. Mobility between employers, networks, and changing hierarchical structures in organizations, as well as personal and family reasons are theorized to bring changes to careers patterns in the future. However, the pace of this change in careers will vary between the ICT and paper business sectors. Findings of this research indicate that business sector has an effect on how managerial careers develop. The environment where career is developed differs between ICT and paper sectors. Careers begin differently in the two environments and the speed of career progression is distinct. ICT careers are built within the business sector whereas paper careers are made inside one company. Also recruiting and socialization practices differ from one sector to the other.

A Study on Fractionation and Ultrafiltration of Proteins with Characterized Modified and Unmodified Membranes

Membrane filtration has become increasingly attractive in the processing of both foodand biotechnological products. However, the poor selectivity of the membranes and fouling are the critical factors limiting the development of UF systems for the specific fractionation of protein mixtures. This thesis gives an overview on fractionation of proteins from model protein solutions or from biological solutions. An attempt was made to improve the selectivity of the available membranes by modifying the membranes and by exploiting the different electrostatic interactions between the proteins and the membrane pore surfaces. Fractionation and UF behavior of proteins in the model solutions and in the corresponding biological solutions were compared. Characterization of the membranes and protein adsorptionto the membrane were investigated with combined flux and streaming potential studies. It has been shown that fouling of the membranes can be reduced using "self-rejecting" membranes at pH values where electrostatic repulsion is achieved between the membrane and the proteins in solution. This effect is best shown in UF of dilute single protein solutions at low ionic strengths and low pressures. Fractionation of model proteins in single, binary, and ternary solutionshas been carried out. The results have been compared to the results obtained from fractination of biological solutions. It was generally observed that fractination of proteins from biological solutions are more difficult to carry out owingto the presence of non studied protein components with different properties. Itcan be generally concluded that it is easier to enrich the smaller protein in the permeate but it is also possible to enrich the larger protein in the permeateat pH values close to the isoelectric point of the protein. It should be possible to find an optimal flux and modification to effectively improve the fractination of proteins even with very similar molar masses.

Experimental and Numerical Analysis of Different Volutes in a Centrifugal Compressor

In a centrifugal compressor the flow around the diffuser is collected and led to the pipe system by a spiral-shaped volute. In this study a single-stage centrifugal compressor with three different volutes is investigated. The compressorwas first equipped with the original volute, the cross-section of which was a combination of a rectangle and semi-circle. Next a new volute with a fully circular cross-section was designed and manufactured. Finally, the circular volute wasmodified by rounding the tongue and smoothing the tongue area. The overall performance of the compressor as well as the static pressure distribution after the impeller and on the volute surface were measured. The flow entering the volute was measured using a three-hole Cobra-probe, and flow visualisations were carriedout in the exit cone of the volute. In addition, the radial force acting on theimpeller was measured using magnetic bearings. The complete compressor with thecircular volute (inlet pipe, full impeller, diffuser, volute and outlet pipe) was also modelled using computational fluid dynamics (CFD). A fully 3-D viscous flow was solved using a Navier-Stokes solver, Finflo, developed at Helsinki University of Technology. Chien's k-e model was used to take account of the turbulence. The differences observed in the performance of the different volutes were quite small. The biggest differences were at low speeds and high volume flows,i.e. when the flow entered the volute most radially. In this operating regime the efficiency of the compressor with the modified circular volute was about two percentage points higher than with the other volutes. Also, according to the Cobra-probe measurements and flow visualisations, the modified circular volute performed better than the other volutes in this operating area. The circumferential static pressure distribution in the volute showed increases at low flow, constant distribution at the design flow and decrease at high flow. The non-uniform static pressure distribution of the volute was transmitted backwards across the vaneless diffuser and observed at the impeller exit. At low volume flow a strong two-wave pattern developed into the static pressure distribution at the impeller exit due to the response of the impeller to the non-uniformity of pressure. The radial force of the impeller was the greatest at the choke limit, the smallest atthe design flow, and moderate at low flow. At low flow the force increase was quite mild, whereas the increase at high flow was rapid. Thus, the non-uniformityof pressure and the force related to it are strong especially at high flow. Theforce caused by the modified circular volute was weaker at choke and more symmetric as a function of the volume flow than the force caused by the other volutes.

Laadun kehittäminen suomalaisissa yrityksissä

Laadun ja sen kehittämisen sisältö on ollut jatkuvassa muutostilassa. Laatuajattelu on laajentunut käsittämään yhä suuremman osan organisaatioiden toiminnasta. Laadun kehittämisessä on jatkuvasti otettu käyttöön uusi kehittämiskeinoja. Laaja-alaisesti organisaation toimintaan kytkeytyvistä keinoista tunnetuimpia ovat erilaiset laadunhallintajärjestelmät ja itsearviointi eri kriteeristöjen avulla. Tämän tutkimuksen tavoitteina olivat: a) etsiä motiiveja, minkä vuoksi yritykset ovat alkaneet kehittää laatuaan, b) tutkia total quality management (TQM) -ajattelun soveltamisen syvällisyyden vaikutuksia, c) selvittää laadunkehittämistyön ajallisen keston vaikutuksia, ja d) saada kokonaiskuva keskeisimpien laadun kehittämiskeinojen toteutuksesta ja menestyksellisyydestä. Työn teoriaosassa paneuduttiin laatu-käsitteeseen yritystoiminnassa, laatu- ja TQM-ajattelun sisältöön sekä laadun kehittämisen johtamiseen. Lisäksi tutkittiin keskeisimpiä laadun kehittämisen keinoja, joita olivat mm. ihmisten toiminta, laadunhallintajärjestelmät, itsearvioinnit, toimintaprosessien kehittäminen, asiakas- ja toimittajayhteistyö. Tutkimuksen empiirisessä osassa tutkittiinem. laadun kehittämiseen liittyviä asioita suomalaisissa yrityksissä. Aineisto kerättiin haastattelemalla yritysten laadun kehittämisestä vastaavia henkilöitä 24 yrityksessä. Tulosten esittämisessä hyödynnettiin tilastollisia tutkimusmenetelmiä kvalitatiivisten menetelmien ohella. Tässä aineistossa asiakasvaatimukset ja oma kehityshalu nousivat yleisimmiksi tärkeimmistä laadun kehittämisen aloitusmotiiveista. Mikään tärkeimmistä aloitusmotiiveista ei ollutkuitenkaan johtanut selkeästi ylivoimaisimpaan menestymiseen myöhemmin. TQM-ajattelun laaja-alainen soveltaminen johti laadun kehittämisen kannalta positiiviseen suuntaan. Pisimpään laatuaan kehittäneet yritykset olivat suuria ja kansainvälisesti suuntautuneita. Pelkkä kehitystyön ajallinen kesto näkyi vain vähän kehittämisen eri osa-alueilla. Laadun kehittämistyön menetyksellisyyden kannalta positiivia asioita olivat: henkilöstön aktiivisuus, itsearviointien hyödyntäminen, toimintaprosessien kuvaaminen ja kehittäminen, sekä asiakas- ja toimittajayhteistyö. Laadun kehittämiseen kannattaa ottaa aktiivisesti mukaankoko organisaation henkilöstö. Itsearviointien käytöllä on mahdollista kehittääorganisaatiota laaja-alaisesti. Niin asiakkaat kuin toimittajat kannattaa ottaaaktiivisesti mukaan kehittämistoimintaan. Se on kaikkien osapuolien yhteinen etu.

Pienen matkailuyrityksen yrittäjän taival : Oppiminen yrittäjyysprosessissa

Tämä tutkimus liittyy keskusteluun yrittäjyydestä, strategisesta prosessista ja kasvunmerkityksestä pienissä yrityksissä ja edelleen keskusteluun yrittäjästä oppijana, tilaisuuteen tarttujana ja toisaalta elämäntapaansa vaalivana yksilönä. Yrittäjän oppiminen on liitettävissä keskusteluun oppimisesta organisaatioissa, mikä tässä ymmärretään yrittäjän, yksilön oppimisena ja mahdollisuutena innovointiin ja uusiutumiseen yrittäjyysprosessissa. Tutkimuksen tavoitteena on etsiä yrittäjän oppimisen tapoja ja tuotoksia, roolia ja merkitystä strategisessa liiketoimintaprosessissa, jossa yrittäjän arvot ja pienen matkailu- ja perheyrityksen kulttuuri ohjaavat yrittäjän toimintatapaa. Edelleen tavoitteena on hahmottaa yrittäjän oppimisen ja kompetenssin ilmenemistä muutoksissa ja sidosryhmäsuhteissa. Työn lähestymistapa on hermeneuttinen. Yrittäjää lähestytään kokonaisvaltaisena yksilönä näkökulmasta, jossa yrittäjyyden prosessi ymmärretään inhimillisenä ja luovana toimintana sekä jatkuvana muutoksena. Yrittäjä nähdään oman prosessinsa määrittäjänä ja parhaana asiantuntijana. Empiirinen aineisto on laadullista. Vanhatyrittäjähaastatteluin vuosina 1998 - 99 kerätyt aineistot tarjosivat kokeilumahdollisuuden aineiston analysoinnin aloittamiseksi. Aineistojen kapean näkökulmanlaajentamiseksi kerättiin lisäaineisto neljältä yrittäjältä keskusteluin vuonna2003. Tämä Itä-Suomessa matkailualan yrittäjiltä kerätty uusi aineisto muodostaa tämän tutkimuksen keskeisen aineiston. Yrittäjyyden aiemmasta tutkimuksesta nousseet näkökulmat ovat suunnanneet tämän työn empiirisen aineiston tarkastelua. Tarkastelun kohteena ovat yrittäjä oppijana yrittäjyysprosessissaan ja yrittäjähistoriansa taitekohdissa sekä oppimisen näkyminen yrittäjän arvomaailmassa, matkailuyrityksen kulttuurissa ja sidosryhmäyhteistyössä. Tutkimuksen tulokset osoittavat, että yrittäjille jatkuva muutos on arkipäiväistä työtä. Yrittäjät hallitsevat omaa oppimis- ja yrittäjyysprosessiaan. He asettavat itse tavoitteensa liiketoiminnan suhteen, ymmärtävät liiketaloudellisia realiteetteja riittävästi; erityisesti riskien hallinta on ominaista yrittäjille. Yritysten menestystä osoittaa se, että niissä on pystytty kasvattamaan toimintaa määrällisten mittareiden puitteissa tai ainakin yrittäjän omiin tavoitteisiin on päästy. Yrittäjien oppimis- ja uusiutumiskykyä todistaa yritysten olemassaolo sinänsä ja jatkuva olemassaolon kamppailu vaikuttamalla sidosryhmiin. Vaikka näitä yrittäjiä ei anglosaksisen, schumpeterilaisen määrittelytavan mukaan voida määritellä käsitteellä 'entrepreneur', voidaan kuitenkin väittää, että heidät voidaan ymmärtää 'yrittäjyys' yrittäjiksi - rohkeiksi, uteliaiksi, itsenäisiksi, oppiviksi ja jatkuvasti uusiutuviksi yksilöiksi, jotka luovat jatkuvasti uutta arvoa yritystoiminnallaan. Oppiminen ilmenee prosessissa niin, että yrittäjät hakevat uutta tietoa sosiaalisesta suhdeverkostostaan, asiakkaiden käyttäytymisestä ja reaktioista sekä havainnoivatympäristöään tarkasti tehden vertailuja oman yrityksenä näkökulmasta alan muihin yrityksiin ja toimivat yhteistyössä muiden yrittäjien kanssa. He kyseenalaistavat omaa ja yrityksensä toimintaa, laativat suunnitelmia yrityksen laajentamiseksi tai toimintojen lisäämiseksi, mutta myös toiminnoista luopumiseksi. Oppiminenja uusiutuminen näkyvät visioissa, joissa yritystoimintaa varaudutaan muuttamaan siten, että se vastaa kulloisenkin tilanteen vaatimuksia Kuitenkin yrittäjät ovat ymmärrettävissä toimintaa ennakoiviksi, eivät niinkään toimintaa sopeuttaviksi yksilöiksi. Ennakointi voidaan nähdä muutosten työntövoimana, jolloin yrittäjät ovat enemmänkin yritystensä eteenpäin työntäjiä kuin yritystensä vetäjiä. Yrittäjät ovat omissa yrityksissään paras mahdollinen kyvykkyys- ja osaamisresurssi, joka näyttää siirtyvän näissä yrityksissä myös seuraavan sukupolven käyttöön käytännön esimerkkien ja hiljaisen tiedon kautta. Jokaiselle yrittäjälle on muotoutunut oma selviytymisstrategiansa tai toimintamallinsa, jossa on nähtävissä yrittäjän koko yrittäjyyden historian aikana ja yrittäjyysprosessissa tapahtuvan oppimisen muotoutuminen yrittäjän osaamiseksi. Näissä selviytymisstrategioissa on havaittavissa yrittäjän oma arvokäsitys, perheyrityksen kulttuuri, suhtautumistapa ympäristöön ja yrittäjän oma, persoonallinen toimintatapa yrittäjänä.

Theoretical and numerical study of thermomagnetic convection in magnetic fluids

In this thesis, the magnetic field control of convection instabilities and heat and mass transfer processesin magnetic fluids have been investigated by numerical simulations and theoretical considerations. Simulation models based on finite element and finite volume methods have been developed. In addition to standard conservation equations, themagnetic field inside the simulation domain is calculated from Maxwell equations and the necessary terms to take into account for the magnetic body force and magnetic dissipation have been added to the equations governing the fluid motion.Numerical simulations of magnetic fluid convection near the threshold supportedexperimental observations qualitatively. Near the onset of convection the competitive action of thermal and concentration density gradients leads to mostly spatiotemporally chaotic convection with oscillatory and travelling wave regimes, previously observed in binary mixtures and nematic liquid crystals. In many applications of magnetic fluids, the heat and mass transfer processes including the effects of external magnetic fields are of great importance. In addition to magnetic fluids, the concepts and the simulation models used in this study may be applied also to the studies of convective instabilities in ordinary fluids as well as in other binary mixtures and complex fluids.

Information sharing in R&D collaboration - Context-dependency and means of governance

Tiedon jakaminen ja kommunikointi ovat tärkeitä toimintoja verkostoituneiden yritysten välillä ja ne käsitetäänkin yhteistyösuhteen yhtenä menestystekijänä ja kulmakivenä. Tiedon jakamiseen liittyviä haasteita ovat mm. yrityksen liiketoiminnalle kriittisen tiedon vuotaminen ja liiketoiminnan vaatima tiedon reaaliaikaisuus ja riittävä määrä. Tuotekehitysyhteistyössä haasteellista on tiedon jäsentymättömyys ja sitä kautta lisääntyvä tiedon jakamisen tarve, minkä lisäksi jaettava tieto on usein monimutkaista ja yksityiskohtaista. Lisäksi tuotteiden elinkaaret lyhenevät, ja ulkoistaminen ja yhteistyö ovat yhä kasvavia trendejä liiketoiminnassa. Yhdessä nämä tekijät johtavat siihen, että tiedon jakaminen on haastavaa eritoten verkostoituneiden yritysten välillä. Tässä tutkimuksessa tiedon jakamisen haasteisiin pyrittiin vastaamaan ottamalla lähtökohdaksi tiedon jakamisen tilanneriippuvuuden ymmärtäminen. Työssä vastattiin kahteen pääkysymykseen: Mikä on tiedon jakamisen tilanneriippuvuus ja miten sitä voidaan hallita? Tilanneriippuvuudella tarkoitetaan työssä niitä tekijöitä, jotka vaikuttavat siihen, miten yritys jakaa tietoa tuotekehityskumppaneidensa kanssa. Tiedon jakamisella puolestaan tarkoitetaan yrityksestä toiselle siirrettävää tietoa, jota tarvitaan tuotekehitysprojektin aikana. Työn empiirinen aineisto on kerätty laadullisella tutkimusotteella case- eli tapaustutkimuksena yhdessä telekommunikaatioalan yrityksessä jasen eri liiketoimintayksiköissä. Tutkimusjoukko käsitti 19 tuotekehitys- ja toimittajanhallintatehtävissä toimivaa johtajaa tai päällikköä. Työ nojaa pääasiassa hankintojen johtamisen tutkimuskenttään ja tilanneriippuvuuden selvittämiseksi paneuduttiin erityisesti verkostojen tutkimukseen. Työssä kuvattiin tiedon jakaminen yhtenä verkoston toimintona ja yhteistyöhön liittyvättiedon jakamisen hyödyt, haasteet ja riskit identifioitiin. Tämän lisäksi työssä kehitettiin verkoston tutkimismalleja ja yhdistettiin eri tasoilla tapahtuvaa verkoston tutkimusta. Työssä esitettiin malli verkoston toimintojen tutkimiseksija todettiin, että verkostotutkimusta pitäisi tehdä verkosto, ketju, yrityssuhde- ja yritystasolla. Malliin on myös hyvä yhdistää tuote- ja tehtäväkohtaiset ominaispiirteet. Kirjallisuuskatsauksen perusteella huomattiin, että tiedon jakamista on aiemmin tarkasteltu lähinnä tuote- ja yrityssuhteiden tasolla. Väitöskirjassa esitettiin lisää merkittäviä tekijöitä, jotka vaikuttavat tiedon jakamiseen. Näitä olivat mm. tuotekehitystehtävän luonne, teknologia-alueen kypsyys ja toimittajan kyvykkyys. Tiedon jakamisen luonnetta tarkasteltaessa erotettiin operatiivinen, projektin hallintaan ja tuotekehitykseen liittyvä tieto sekä yleinen, toimittajan hallintaan liittyvä strateginen tieto. Tulosten mukaan erityisesti tuotekehityksen määrittelyvaihe ja tapaamiset kasvotusten korostuivat yhteistyössä. Empirian avulla tutkittiin myös niitä tekijöitä, joilla tiedon jakamista voidaan hallita tilanneriippuvuuteen perustuen, koska aiemmin tiedon jakamisen hallintakeinoja tai menestystekijöitä ei ole liitetty suoranaisesti eri olosuhteisiin. Nämä hallintakeinot jaettiin yhteistyötason- ja tuotekehitysprojektitason tekijöihin. Yksi työn keskeisistä tuloksista on se, että huolimatta tiedon jakamisen haasteista, monet niistä voidaan eliminoida tunnistamalla vallitsevat olosuhteet ja panostamalla tiedon jakamisen hallintakeinoihin. Työn manageriaalinen hyöty koskee erityisesti yrityksiä, jotka suunnittelevat ja tekevät tuotekehitysyhteistyötä yrityskumppaniensa kanssa. Työssä esitellään keinoja tämän haasteellisen tehtäväkentän hallintaan ja todetaan, että yritysten pitäisikin kiinnittää entistä enemmän huomiota tiedon jakamisen ja kommunikaation hallintaan jo tuotekehitysyhteistyötä suunniteltaessa.

Value Processingin Organizations - Individual Perceptions in Three Case Companies

Values and value processes are said to be needed in every organization nowadays, as the world is changing and companies have to have something to "keep it together". Organizational values, which are approvedand used by the personnel, could be the key. Every organization has values. But what is the real value of values? The greatest and most crucial challenge is the feasibility of the value process. The main point in this thesis is tostudy how organizational members at different hierarchical levels perceive values and value processes in their organizations. This includes themes such as how values are disseminated, the targets of value processing, factors that affect the process, problems that occur during the value implementation and improvements that could be made when organizational values are implemented. These subjects are studied from the perspective of organizational members (both managers and employees); individuals in the organizations. The aim is to get the insider-perspective on value processing, from multiple hierarchical levels. In this research I study three different organizations (forest industry, bank and retail cooperative) and their value processes. The data is gathered from companies interviewing personnel in the head office and at the local level. The individuals areseen as members of organizations, and the cultural aspect is topical throughout the whole study. Values and cultures are seen as the 'actuality of reality' of organizations, interpreted by organizational members. The three case companies were chosen because they represented different lines of business and they all implemented value processing differently. Sincethe emphasis in this study is at the local level, the similar size of the local units was also an important factor. Values are in 'fashion' -but what does the fashion tell us about the real corporate practices? In annual reports companies emphasize the importance and power of official values. But what is the real 'point' of values? Values are publicly respected and advertised, but still it seems that the words do not meet the deeds. There is a clear conflict between theoretical, official and substantive organizational values: in the value processing from words to real action. This contradiction in value processing is studied through individual perceptions in this study. I study the kinds of perceptions organizationalmembers have when values are processed from the head office to the local level: the official value process is studied from the individual's perspective. Value management has been studied more during the 1990's. The emphasis has usually been on managers: how they consider the values in organizations and what effects it has on the management. Recent literature has emphasized values as tools for improving company performance. The value implementation as a process has been studied through 'good' and 'bad' examples, as if one successful value process could be copied to all organizations. Each company is different with different cultures and personnel, so no all-powerful way of processing values exists. In this study, the organizational members' perceptions at different hierarchical levels are emphasized. Still, managers are also interviewed; this is done since managerial roles in value dissemination are crucial. Organizational values cannot be well disseminated without management; this has been proved in several earlier studies (e.g. Kunda 1992, Martin 1992, Parker 2000). Recent literature has not sufficiently emphasized the individual's (organizational member's) role in value processing. Organizations consist of differentindividuals with personal values, at all hierarchical levels. The aim in this study is to let the individual take the floor. Very often the value process is described starting from the value definition and ending at dissemination, and the real results are left without attention. I wish to contribute to this area. Values are published officially in annual reports etc. as a 'goal' just like profits. Still, the results/implementationof value processing is rarely followed, at least in official reports. This is a very interesting point: why do companies espouse values, if there is no real control or feedback after the processing? In this study, the personnel in three different companies is asked to give an answer. In the empirical findings, there are several results which bring new aspects to the research area of organizational values. The targets of value processing, factors effecting value processing, the management's roles and the problems in value implementation are presented through the individual's perspective. The individual's perceptions in value processing are a recurring theme throughout the whole study. A comparison between the three companies with diverse value processes makes the research complete

Logging residues from regeneration fellings for biofuel production - a GIS-based availability and supply cost analysis

Finland has large forest fuel resources. However, the use of forest fuels for energy production has been low, except for small-scale use in heating. According to national action plans and programs related to wood energy promotion, the utilization of such resources will be multiplied over the next few years. The most significant part of this growth will be based on the utilization of forest fuels, produced from logging residues of regeneration fellings, in industrial and municipal power and heating plants. Availability of logging residues was analyzed by means of resource and demand approaches in order to identify the most suitable regions with focus on increasing the forest fuel usage. The analysis included availability and supply cost comparisons between power plant sites and resource allocation in a least cost manner, and between a predefined power plant structure under demand and supply constraints. Spatial analysis of worksite factors and regional geographies were carried out using the GIS-model environment via geoprocessing and cartographic modeling tools. According to the results of analyses, the cost competitiveness of forest fuel supply should be improved in order to achieve the designed objectives in the near future. Availability and supply costs of forest fuels varied spatially and were very sensitive to worksite factors and transport distances. According to the site-specific analysis the supply potential between differentlocations can be multifold. However, due to technical and economical reasons ofthe fuel supply and dense power plant infrastructure, the supply potential is limited at plant level. Therefore, the potential and supply cost calculations aredepending on site-specific matters, where regional characteristics of resourcesand infrastructure should be taken into consideration, for example by using a GIS-modeling approach constructed in this study.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.