Characterization of thirty two microsatellite loci for three Atlanto-Mediterranean echinoderm species

Thirty two microsatellites were optimized from 454 pyrosequencing libraries for three Atlanto-Mediterranean echinoderms: Coscinasterias tenuispina, Echinaster sepositus and Arbacia lixula. We observed different frequency of microsatellite types (di-, tri-, tetra- and pentanucleotide) throughout the genome of the species, but no significant differences were observed in allele richness among different microsatellite repeats. No loci showed linkage disequilibrium. Heterozygosity deficit and departure from Hardy Weinberg equilibrium were observed for some loci, in two species, probably due to high levels of inbreeding. Heterozygosity excess observed in C. tenuispina could be explained by selection against homozygotes and/or outcrossing.

Polarimetric radar interferometry for improved mine detection and surface clutter rejection

A recently developed technique, polarimetric radar interferometry, is applied to tackle the problem of the detection of buried objects embedded in surface clutter. An experiment with a fully polarimetric radar in an anechoic chamber has been carried out using different frequency bands and baselines. The processed results show the ability of this technique to detect buried plastic mines and to measure their depth. This technique enables the detection of plastic mines even if their backscatter response is much lower than that of the surface clutter.

Architectural characterization of a delta-front reservoir analogue combining ground penetrating radar and electrical resistivity tomography: Roda Sandstone (Lower Eocene, Graus-Tremp basin, Spain)

Three-dimensional reconstruction of reservoir analogues can be improved combining data from different geophysical methods. Ground Penetrating Radar (GPR) and Electrical Resistivity Tomography (ERT) data are valuable tools, since they provide subsurface information from internal architecture and facies distribution of sedimentary rock bodies, enabling the upgrading of depositional models and heterogeneity reconstruction. The Lower Eocene Roda Sandstone is a well-known deltaic complex widely studied as a reservoir analogue that displays a series of sandstone wedges with a general NE to SW progradational trend. To provide a better understanding of internal heterogeneity of a 10m-thick progradational delta-front sandstone unit, 3D GPR data were acquired. In addition, common midpoints (CMP) to measure the sandstone subsoil velocity, test profiles with different frequency antennas (25, 50 and 100MHz) and topographic data for subsequent correction in the geophysical data were also obtained. Three ERT profiles were also acquired to further constrain GPR analysis. These geophysical results illustrate the geometry of reservoir analogue heterogeneities both depositional and diagenetic in nature, improving and complementing previous outcrop-derived data. GPR interpretation using radar stratigraphy principles and attributes analysis provided: 1)tridimensional geometry of major stratigraphic surfaces that define four units in the GPR Prism, 2) image the internal architecture of the units and their statistical study of azimuth and dips, useful for a quick determination of paleocurrent directions. These results were used to define the depositional architecture of the progradational sandbody that shows an arrangement in very-high-frequency sequences characterized by clockwise paleocurrent variations and decrease of the sedimentary flow, similar to those observed at a greater scale in the same system. This high-frequency sequential arrangement has been attributed to the autocyclic dynamics of a supply-dominated delta- front where fluvial and tidal currents are in competition. The resistivity models enhanced the viewing of reservoir quality associated with cement distribution caused by depositional and early diagenetic processes related to the development of transgressive and regressive systems tracts in igh-frequency sequences.

Characterization of thirty two microsatellite loci for three Atlanto-Mediterranean echinoderm species

Thirty two microsatellites were optimized from 454 pyrosequencing libraries for three Atlanto-Mediterranean echinoderms: Coscinasterias tenuispina, Echinaster sepositus and Arbacia lixula. We observed different frequency of microsatellite types (di-, tri-, tetra- and pentanucleotide) throughout the genome of the species, but no significant differences were observed in allele richness among different microsatellite repeats. No loci showed linkage disequilibrium. Heterozygosity deficit and departure from Hardy Weinberg equilibrium were observed for some loci, in two species, probably due to high levels of inbreeding. Heterozygosity excess observed in C. tenuispina could be explained by selection against homozygotes and/or outcrossing.

A hybrid feature selection approach for the early diagnosis of Alzheimer's disease

Objective. Recently, significant advances have been made in the early diagnosis of Alzheimer’s disease from EEG. However, choosing suitable measures is a challenging task. Among other measures, frequency Relative Power and loss of complexity have been used with promising results. In the present study we investigate the early diagnosis of AD using synchrony measures and frequency Relative Power on EEG signals, examining the changes found in different frequency ranges. Approach. We first explore the use of a single feature for computing the classification rate, looking for the best frequency range. Then, we present a multiple feature classification system that outperforms all previous results using a feature selection strategy. These two approaches are tested in two different databases, one containing MCI and healthy subjects (patients age: 71.9 ± 10.2, healthy subjects age: 71.7 ± 8.3), and the other containing Mild AD and healthy subjects (patients age: 77.6 ± 10.0; healthy subjects age: 69.4± 11.5). Main Results. Using a single feature to compute classification rates we achieve a performance of 78.33% for the MCI data set and of 97.56 % for Mild AD. Results are clearly improved using the multiple feature classification, where a classification rate of 95% is found for the MCI data set using 11 features, and 100% for the Mild AD data set using 4 features. Significance. The new features selection method described in this work may be a reliable tool that could help to design a realistic system that does not require prior knowledge of a patient's status. With that aim, we explore the standardization of features for MCI and Mild AD data sets with promising results.

Frequency resolved admittance spectroscopy measurements on In0.52Al0.48As/InxGa1¿xAs/In0.52Al0.48As single quantum well structures

In this work a new admittance spectroscopy technique is proposed to determine the conduction band offset in single quantum well structures (SQW). The proposed technique is based on the study of the capacitance derivative versus the frequency logarithm. This method is found to be less sensitive to parasitic effects, such as leakage current and series resistance, than the classical conductance analysis. Using this technique, we have determined the conduction band offset in In0.52Al0.48As/InxGa1¿xAs/In0.52Al0.48As SQW structures. Two different well compositions, x=0.53, which corresponds to the lattice¿matched case and x=0.60, which corresponds to a strained case, and two well widths (5 and 25 nm) have been considered. The average results are ¿Ec=0.49±0.04 eV for x=0.53 and ¿Ec =0.51±0.04 eV for x=0.6, which are in good agreement with previous reported data.

Polymorphous Si thin films from radio frequency plasmas of SiH4 diluted in Ar: A study by transmission electron microscopy and Raman spectroscopy

In this study, we present a detailed structural characterization by means of transmission electron microscopy and Raman spectroscopy of polymorphous silicon (pm-Si:H) thin films deposited using radio-frequency dust-forming plasmas of SiH4 diluted in Ar. Square-wave modulation of the plasma and gas temperature was varied to obtain films with different nanostructures. Transmission electron microscopy and electron diffraction have shown the presence of Si crystallites of around 2 nm in the pm-Si:H films, which are related to the nanoparticles formed in the plasma gas phase coming from their different growth stages, named particle nucleation and coagulation. Raman scattering has proved the role of the film nanostructure in the crystallization process induced ¿in situ¿ by laser heating.

Ion assisted deposition of thin films by substrate tuned radio frequency magnetron sputtering

The substrate tuning technique was applied to a radio frequency magnetron sputtering system to obtain a variable substrate bias without an additional source. The dependence of the substrate bias on the value of the external impedance was studied for different values of chamber pressure, gas composition and rf input power. A qualitative explanation of the results is given, based on a simple model, and the role of the stray capacitance is clearly disclosed. Langmuir probe measurements show that this system allows independent control of the ion flux and the ion energy bombarding the growing film. For an argon flow rate of 2.8 sccm and a radio frequency power of 300 W (intermediate values of the range studied) the ion flux incident on the substrate was 1.3 X 1020-m-2-s-1. The maximum ion energy available in these conditions can be varied in the range 30-150 eV. As a practical application of the technique, BN thin films were deposited under different ion bombardment conditions. An ion energy threshold of about 80 eV was found, below which only the hexagonal phase was present in the films, while for higher energies both hexagonal and cubic phase were present. A cubic content of about 60% was found for an ion energy of 120 V.

Production of nanometric particles in radio frequency glow discharges in mixtures of silane and methane

The formation of silicon particles in rf glow discharges has attracted attention due to their effect as a contaminant during film deposition or etching. However, silicon and silicon alloy powders produced by plasma¿enhanced chemical vapor deposition (PECVD) are promising new materials for sintering ceramics, for making nanoscale filters, or for supporting catalytic surfaces. Common characteristics of these powders are their high purity and the easy control of their stoichiometry through the composition of the precursor gas mixture. Plasma parameters also influence their structure. Nanometric powders of silicon¿carbon alloys exhibiting microstructural properties such as large hydrogen content and high surface/volume ratio have been produced in a PECVD reactor using mixtures of silane and methane at low pressure (-1 Torr) and low frequency square¿wave modulated rf power (13.56 MHz). The a¿Si1¿xCx:H powders were obtained from different precursor gas mixtures, from R=0.05 to R=9, where R=[SiH4]/([SiH4]+[CH4]). The structure of the a¿Si1¿xCx:H powder was analyzed by several techniques. The particles appeared agglomerated, with a wide size distribution between 5 and 100 nm. The silane/methane gas mixture determined the vibrational features of these powders in the infrared. Silicon-hydrogen groups were present for every gas composition, whereas carbon¿hydrogen and silicon¿carbon bonds appeared in methane¿rich mixtures (R-0.6). The thermal desorption of hydrogen revealed two main evolutions at about 375 and 660¿°C that were ascribed to hydrogen bonded to silicon and carbon, respectively. The estimated hydrogen atom concentration in the sample was about 50%.

Positive time-frequency distributions based on joint marginal constraints

This correspondence studies the formulation of members ofthe Cohen-Posch class of positive time-frequency energy distributions.Minimization of cross-entropy measures with respect to different priorsand the case of no prior or maximum entropy were considered. It isconcluded that, in general, the information provided by the classicalmarginal constraints is very limited, and thus, the final distributionheavily depends on the prior distribution. To overcome this limitation,joint time and frequency marginals are derived based on a "directioninvariance" criterion on the time-frequency plane that are directly relatedto the fractional Fourier transform.

Generic utilities in chronic obstructive pulmonary disease patients stratified according to different staging systems.

Background To determine generic utilities for Spanish chronic obstructive pulmonary disease (COPD) patients stratified by different classifications: GOLD 2007, GOLD 2013, GesEPOC 2012 and BODEx index. Methods Multicentre, observational, cross-sectional study. Patients were aged ≥40 years, with spirometrically confirmed COPD. Utility values were derived from EQ-5D-3 L. Means, standard deviations (SD), medians and interquartile ranges (IQR) were computed based on the different classifications. Differences in median utilities between groups were assessed by non-parametric tests. Results 346 patients were included, of which 85.5% were male with a mean age of 67.9 (SD = 9.7) years and a mean duration of COPD of 7.6 (SD = 5.8) years; 80.3% were ex-smokers and the mean smoking history was 54.2 (SD = 33.2) pack-years. Median utilities (IQR) by GOLD 2007 were 0.87 (0.22) for moderate; 0.80 (0.26) for severe and 0.67 (0.42) for very-severe patients (p < 0.001 for all comparisons). Median utilities by GOLD 2013 were group A: 1.0 (0.09); group B: 0.87 (0.13); group C: 1.0 (0.16); group D: 0.74 (0.29); comparisons were statistically significant (p < 0.001) except A vs C. Median utilities by GesEPOC phenotypes were 0.84 (0.33) for non exacerbator; 0.80 (0.26) for COPD-asthma overlap; 0.71 (0.62) for exacerbator with emphysema; 0.72 (0.57) for exacerbator with chronic bronchitis (p < 0.001). Comparisons between patients with or without exacerbations and between patients with COPD-asthma overlap and exacerbator with chronic bronchitis were statistically-significant (p < 0.001). Median utilities by BODEx index were: group 02: 0.89 (0.20); group 34: 0.80 (0.27); group 56: 0.67 (0.29); group 79: 0.41 (0.31). All comparisons were significant (p < 0.001) except between groups 34 and 56. Conclusion Irrespective of the classification used utilities were associated to disease severity. Some clinical phenotypes were associated with worse utilities, probably related to a higher frequency of exacerbations. GOLD 2007 guidelines and BODEx index better discriminated patients with a worse health status than GOLD 2013 guidelines, while GOLD 2013 guidelines were better able to identify a smaller group of patients with the best health.

Effect of flushing frequency on emitter clogging in microirrigation with effluents

Flushing is an important maintenance task that removes accumulated particles in microirrigation laterals that can help to reduce clogging problems. The effect of three dripline flushing frequency treatments (no flushing, one flushing at the end of each irrigation period, and a monthly flushing during the irrigation period) was studied in surface and subsurface drip irrigation systems that operated using a wastewater treatment plant effluent for three irrigation periods of 540 h each. The irrigation systems had two different emitters, one pressure compensating and the other not, both molded and welded onto the interior dripline wall, placed in laterals 87 meters long. Dripline flow of the pressure compensating emitter increased 8% over time, while in the nonpressure compensating emitter, dripline flow increased 25% in the surface driplines and decreased 3% in the subsurface driplines by the emitter clogging. Emitter clogging was affected primarily by the interactions between emitter location, emitter type, and flushing frequency treatment. The number of completely clogged emitters was affected by the interaction between irrigation system and emitter type. There was an average of 3.7% less totally clogged emitters in flushed surface driplines with the pressurecompensating emitter as compared to flushed subsurface laterals with the nonpressure compensating emitter

The role of different factors related to social impact of heavy events: considerations about the intensity thresholds in densely populated areas

In the assessment of social impact caused by meteorological events, factors of different natures need to be considered. Not only does hazard itself determine the impact that a severe weather event has on society, but also other features related to vulnerability and exposure. The requests of data related to insurance claims received in meteorological services proved to be a good indicator of the social impact that a weather event causes, according to studies carried out by the Social Impact Research Group, created within the framework of the MEDEX project. Taking these requests as proxy data, diverse aspects connected to the impact of heavy rain events have been studied. The rainfall intensity, in conjunction with the population density, has established itself as one of the key factors in social impact studies. One of the conclusions we obtained is that various thresholds of rainfall should be applied for areas of varying populations. In this study, the role of rainfall intensity has been analysed for a highly populated urban area like Barcelona. A period without significant population changes has been selected for the study to minimise the effects linked to vulnerability and exposure modifications. First, correlations between rainfall recorded in different time intervals and requests were carried out. Afterwards, a method to include the intensity factor in the social impact index was suggested based on return periods given by intensity duration frequency (IDF) curves.