Analysis and design of sinusoidal quadrature RC-oscillators

Modern telecommunication equipment requires components that operate in many different frequency bands and support multiple communication standards, to cope with the growing demand for higher data rate. Also, a growing number of standards are adopting the use of spectrum efficient digital modulations, such as quadrature amplitude modulation (QAM) and orthogonal frequency division multiplexing (OFDM). These modulation schemes require accurate quadrature oscillators, which makes the quadrature oscillator a key block in modern radio frequency (RF) transceivers. The wide tuning range characteristics of inductorless quadrature oscillators make them natural candidates, despite their higher phase noise, in comparison with LC-oscillators. This thesis presents a detailed study of inductorless sinusoidal quadrature oscillators. Three quadrature oscillators are investigated: the active coupling RC-oscillator, the novel capacitive coupling RCoscillator, and the two-integrator oscillator. The thesis includes a detailed analysis of the Van der Pol oscillator (VDPO). This is used as a base model oscillator for the analysis of the coupled oscillators. Hence, the three oscillators are approximated by the VDPO. From the nonlinear Van der Pol equations, the oscillators��� key parameters are obtained. It is analysed first the case without component mismatches and then the case with mismatches. The research is focused on determining the impact of the components��� mismatches on the oscillator key parameters: frequency, amplitude-, and quadrature-errors. Furthermore, the minimization of the errors by adjusting the circuit parameters is addressed. A novel quadrature RC-oscillator using capacitive coupling is proposed. The advantages of using the capacitive coupling are that it is noiseless, requires a small area, and has low power dissipation. The equations of the oscillation amplitude, frequency, quadrature-error, and amplitude mismatch are derived. The theoretical results are confirmed by simulation and by measurement of two prototypes fabricated in 130 nm standard complementary metal-oxide-semiconductor (CMOS) technology. The measurements reveal that the power increase due to the coupling is marginal, leading to a figure-of-merit of -154.8 dBc/Hz. These results are consistent with the noiseless feature of this coupling and are comparable to those of the best state-of-the-art RC-oscillators, in the GHz range, but with the lowest power consumption (about 9 mW). The results for the three oscillators show that the amplitude- and the quadrature-errors are proportional to the component mismatches and inversely proportional to the coupling strength. Thus, increasing the coupling strength decreases both the amplitude- and quadrature-errors. With proper coupling strength, a quadrature error below 1�� and amplitude imbalance below 1% are obtained. Furthermore, the simulations show that increasing the coupling strength reduces the phase noise. Hence, there is no trade-off between phase noise and quadrature error. In the twointegrator oscillator study, it was found that the quadrature error can be eliminated by adjusting the transconductances to compensate the capacitance mismatch. However, to obtain outputs in perfect quadrature one must allow some amplitude error.

Design of a doctorate programme on technology assessment: A sabbatical leave project

The work agenda includes the production of a report on different doctoral programmes on ���Technology Assessment��� in Europe, the US and Japan, in order to analyse collaborative post-graduation activities. Finally, the proposals on collaborative post-graduation programme between FCTUNL and ITAS-FZK will be organised by an ongoing discussion process with colleagues from ITAS.

Design of New Materials for Passive Vibration Control

The objective of this contribution is to extend the models of cellular/composite material design to nonlinear material behaviour and apply them for design of materials for passive vibration control. As a first step a computational tool allowing determination of optimised one-dimensional isolator behaviour was developed. This model can serve as a representation for idealised macroscopic behaviour. Optimal isolator behaviour to a given set of loads is obtained by generic probabilistic metaalgorithm, simulated annealing. Cost functional involves minimization of maximum response amplitude in a set of predefined time intervals and maximization of total energy absorbed in the first loop. Dependence of the global optimum on several combinations of leading parameters of the simulated annealing procedure, like neighbourhood definition and annealing schedule, is also studied and analyzed. Obtained results facilitate the design of elastomeric cellular materials with improved behaviour in terms of dynamic stiffness for passive vibration control.

Design of New Materials for Passive Vibration Control

The aim of this contribution is to extend the techniques of composite materials design to non-linear material behaviour and apply it for design of new materials for passive vibration control. As a first step a computational tool allowing determination of macroscopic optimized one-dimensional isolator behaviour was developed. Voigt, Maxwell, standard and more complex material models can be implemented. Objective function considers minimization of the initial reaction and/or displacement peak as well as minimization of the steady-state amplitude of reaction and/or displacement. The complex stiffness approach is used to formulate the governing equations in an efficient way. Material stiffness parameters are assumed as non-linear functions of the displacement. The numerical solution is performed in the complex space. The steady-state solution in the complex space is obtained by an iterative process based on the shooting method which imposes the conditions of periodicity with respect to the known value of the period. Extension of the shooting method to the complex space is presented and verified. Non-linear behaviour of material parameters is then optimized by generic probabilistic meta-algorithm, simulated annealing. Dependence of the global optimum on several combinations of leading parameters of the simulated annealing procedure, like neighbourhood definition and annealing schedule, is also studied and analyzed. Procedure is programmed in MATLAB environment.

Design of switched-capacitor filters using low gain amplifiers

Disserta����o para obten����o do Grau de Mestre em Engenharia Electrot��cnica e de Computadores

Outcomes of communication competence: A study on a Portuguese restaurant chain

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA ��� School of Business and Economics

UsaGame ��� A new methodology to support user- centered design of touchscreen game applications

Disserta����o para Obten����o do Grau de Mestre em Engenharia e Gest��o Industrial

User-centered design of the interface prototype of a business intelligence mobile application

Disserta����o para obten����o do Grau de Mestre em Engenharia e Gest��o Industrial

Design of a power output stage for a class D audio power amplifier based on an 1.5-bit ��� ��� M

Disserta����o apresentada para obten����o do Grau de Mestre em Engenharia Electrot��cnica e de Computadores, pela Universidade Nova de Lisboa, Faculdade de Ci��ncias e Tecnologia

Design of future distribution grids

Disserta����o para obten����o do Grau de Mestre em Engenharia Electrot��cnica e de Computadores

Design of multidimensional compact constellations with high power efficiency

Disserta����o apresentada para obten����o do Grau de Mestre em Engenharia Electrot��cnica e de Computadores, pela Universidade Nova de Lisboa, Faculdade de Ci��ncias e Tecnologia

Optimization based design of LC voltage controlled oscilators

Disserta����o para obten����o do Grau de Doutor em Engenharia Electrot��cnica e de Computadores

Design of a balanced scorecard-type management system for a back-office department in a bank

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Finance from the NOVA ��� School of Business and Economics

Design of a Continuous-Time (CT) Sigma-Delta modulator for class D audio power amplifiers

Disserta����o apresentada na Faculdade de Ci��ncias e Tecnologia da Universidade Nova de Lisboa para obten����o do Grau de Mestre em Engenharia Electrot��cnica e de Computadores

Design of a tool to study the fate of Chlamydia trachomatis infected cells

Chlamydia trachomatis has a unique obligate intracellular developmental cycle that ends by the lysis of the cell and/or the extrusion of the bacteria in order to allow for re-infections. While Chlamydia trachomatis infections are often asymptomatic the diagnosis of Chlamydia trachomatis is usually late, occurring after manifestation of persistency. Investigations on the consequences of long-term infections and the molecular mechanisms behind it will reveal light to what extent bacteria can modulate host cell function and what the ultimate fate of host cells after clearance of an infection is. Such studies on the host cell fate could be greatly facilitated if the infected cells become permanently marked during and after the infection. Therefore, this project intends to develop a new genetic tool that would allow permanently labeling of Chlamydia trachomatis host cells. The plan was to generate a Chlamydia trachomatis strain that encodes a recombinant CRE recombinase, fused to a secretory effector function of the Chlamydia type 3 secretion system (T3SS). Upon translocation into the host cell, this recombinant CRE enzyme could then, owing to its site-specific recombination function, switch a reporter gene contained in the host cell genome. To this end, the reporter line carried a membrane-tagged tdTomato (mT) gene flanked by two LoxP sequences followed by a GFP gene. The translocation of the recombinant CRE recombinase into this cell line was designed to trigger the recombination of the LoxP sites whereby the cells would turn from red fluorescence to green as an irreversible label of the infected cells. Successful execution of this mechanism would allow to draw a direct link between Chlamydia trachomatis infection and the subsequent fate of the infected cell.