15 resultados para 15-150
em Repositório Científico do Instituto Politécnico de Lisboa - Portugal
Resumo:
Enthalpies of solution of 1-butyl-3-methylimidazolium tetra fluoroborate, [BMIm]BF4, are reported at 298.15 K in a set of 15 hydrogen bond donor and hydrogen bond acceptor solvents, chosen by their diversity, namely, water, methanol, ethanol, 1,2-ethanediol, 2-choroethanol, 2-methoxyethanol, formamide, propylene carbonate, nitromethane, acetonitrile, dimethyl sulfoxide, acetone, N,N-dimethylformamide, N,N-dimethylacetamide, and aniline. These values are shown to be largely independent of [BMIm]BF4 concentration. The obtained enthalpies of solution vary from very endothermic to quite exothermic, thus showing a very high sensitivity of the enthalpies of solution of [BMIm]BF4 to solvent properties. Solvent effects on the solution process of this IL are analyzed by a quantitative structure-property relationship methodology, using the TAKA equation and a modified equation, which significantly improves the model's predictive ability. The observed differences in the enthalpies of solution are rationalized in terms of the solvent properties found to be relevant, that is, pi* and E-T(N).
Resumo:
Thin films of TiO2 were doped with Au by ion implantation and in situ during the deposition. The films were grown by reactive magnetron sputtering and deposited in silicon and glass substrates at a temperature around 150 degrees C. The undoped films were implanted with Au fiuences in the range of 5 x 10(15) Au/cm(2)-1 x 10(17) Au/cm(2) with a energy of 150 keV. At a fluence of 5 x 10(16) Au/cm(2) the formation of Au nanoclusters in the films is observed during the implantation at room temperature. The clustering process starts to occur during the implantation where XRD estimates the presence of 3-5 nm precipitates. After annealing in a reducing atmosphere, the small precipitates coalesce into larger ones following an Ostwald ripening mechanism. In situ XRD studies reveal that Au atoms start to coalesce at 350 degrees C, reaching the precipitates dimensions larger than 40 nm at 600 degrees C. Annealing above 700 degrees C promotes drastic changes in the Au profile of in situ doped films with the formation of two Au rich regions at the interface and surface respectively. The optical properties reveal the presence of a broad band centered at 550 nm related to the plasmon resonance of gold particles visible in AFM maps. (C) 2011 Elsevier B.V. All rights reserved.
Resumo:
Embora o título desta Dissertação seja “Reabilitação de um edifício situado na zona histórica do Bairro Alto, Rua da Rosa, nº15”, serão apresentados associados a este tema diversos sub-temas a saber, tais como: O enquadramento histórico que deu origem ao estado actual do Bairro Alto, desde os primórdios do nascimento do aglomerado urbano. Inventariação e levantamento das tipologias representativas dos edifícios que constituem o núcleo central do Bairro Alto. Inventariação e levantamento das patologias representativas dos edifícios com a identificação da sua origem e contribuição para a degradação do edificado. As motivações que concorreram para a construção neste Bairro de edifícios de base Monumental, de uma riqueza patrimonial que chegou aos nossos tempos, fruto das trocas comerciais no advento da época dos Descobrimentos e referências aos condicionamentos legais que são colocados às operações reabilitação dos edifícios deste bairro. Abordagem à evolução demográfica no Bairro, assim como ao seu enquadramento, em termos sócio-profissionais e da regeneração da sua população, com base em resultados apurados nos censos à população. Numa fase posterior, apresentar-se-á um estudo síntese de reabilitação de um edifício situado na Rua da Rosa, nº15, que não inclui a elaboração de projecto específico, integrado em quarteirão tipo. Serão apresentadas conclusões finais, através da extrapolação da solução para o edifício em estudo, em primeiro lugar para o quarteirão onde o edifício se encontra integrado e depois para a restante área central do Bairro Alto. Serão também efectuadas referências aos constrangimentos a uma adequada requalificação dos edifícios, que deveria ter por base a unidade “quarteirão”, fruto em grande medida da excessiva densidade de construção, assim como da ocupação excessiva dos solos, que ultrapassa todos os limites admissíveis do ponto de vista urbanístico e que entra em “conflito” com os actuais regulamentos urbanísticos aplicáveis às novas zonas a urbanizar, pelo que e em face da transparência, é urgente a elaboração de um Regulamento que não levantasse duvidas aos promotores imobiliários, quando tencionassem intervir em operações de reabilitação no edificado.
Resumo:
The immobilized glucose 2-oxidase (pyranose oxidase, pyranose:oxygen-2-oxidoreductase, EC 1.1.3.10) from Coriolus versicolor was used to convert D-glucose into D-glucosone at moderate pressures, up to 150 bar, with compressed air in a modified commercial batch reactor. Several parameters affecting biocatalysis at moderate pressures were investigated as follows: pressure, different forms of immobilized biocatalysts, glucose concentration, pH, temperature and the presence of catalase. Glucose 2-oxidase (GOX2) was purified by immobilized metal affinity chromatography on epoxy-activated Sepharose 6B-IDA-Cu(II) column at pH 6.0. Purified enzyme and catalase were immobilized into a polyethersulfone (PES) membrane in the presence of glutaraldehyde and gelatin. Enhancement of the bioconversion of D-glucose was done by the pressure since an increase in the pressure with compressed air increases the conversion rates. The optimum temperature and pH for bioconversion of D-glucose were found to be 62 degrees C and pH 6.0, respectively and the activation energy (E(a)) was 28.01 kJ mol(-1). The apparent kinetic constants (V(max)' K(m)', K(cat)' and K(cat)/K(m)') for this bioconversion were 2.27 U mg(-1) protein, 11.15 mM, 8.33 s(-1) and 747.38 s(-1) M(-1), respectively. The immobilized biomass of C. versicolor as well as crude extract containing GOX2 activity were also useful for bioconversion of D-glucose at 65 bar with a yield of 69.9 +/- 3.8% and 91.3 +/- 1.2%, respectively. The immobilized enzyme was apparently stable for several months without any significant loss of enzyme activity. On the other hand, this immobilized enzyme was also stable at moderate pressures, since such pressures did not affect significantly the enzyme activity. (C) 2010 Elsevier Ltd. All rights reserved.
Resumo:
This article reports on the structural, electronic, and optical properties of boron-doped hydrogenated nanocrystalline silicon (nc-Si: H) thin films. The films were deposited by plasma-enhanced chemical vapour deposition (PECVD) at a substrate temperature of 150 degrees C. Crystalline volume fraction and dark conductivity of the films were determined as a function of trimethylboron-to-silane flow ratio. Optical constants of doped and undoped nc-Si: H were obtained from transmission and reflection spectra. By employing p(+) nc-Si: H as a window layer combined with a p' a-SiC buffer layer, a-Si: H-based p-p'-i-n solar cells on ZnO:Al-coated glass substrates were fabricated. Device characteristics were obtained from current-voltage and spectral-response measurements. (C) 2011 Elsevier B. V. All rights reserved.
Resumo:
Eucalyptus globulus heartwood, sapwood and their delignified samples by kraft pulping at 130, 150 and 170 degrees C along time were characterized in respect to total carbohydrates by Py-GC/MS(FID). No significant differences between heartwood and sapwood were found in relation to pyrolysis products and composition. The main wood carbohydrate derived pyrolysis compounds were levoglucosan (25.1%), hydroxyacetaldehyde (12.5%), 2-oxo-propanal (10.3%) and acetic acid (8.7%). Levoglucosan decreased during the early stages of delignification and increased during the bulk and residual phases. Acetic acid decreased hydroxyacetaldehyde and 2-oxo-propanal increased, and 2-furaldehyde and hydroxypropanone remained almost constant during delignification. The C/L ratio was 3.2 in wood and remained rather constant in the first pulping periods until a loss of 15-25% in carbohydrate and 60% in lignin. Afterwards it increased sharply until 44 that correspond to the removal of 25-35% of carbohydrates and 95% of lignin. The pulping reactive selectivity to lignin vs. polysaccharides was the same for sapwood and heartwood. (C) 2013 Elsevier B.V. All rights reserved.
Resumo:
Dissertação apresentada à Escola Superior de Educação de Lisboa para obtenção do grau de Mestre em Intervenção Precoce
Resumo:
Dissertação apresentada para obtenção do grau de Mestre em Ciências da Educação Área de especialização em Intervenção Precoce
Resumo:
The most common causes of anemia are micronutrient deficiencies, but other factors may influence namely inflammation, parasitic infections and inherited disorders. One strategy to combat micronutrient deficiencies is supplementation, yet, in zones with high prevalence of Schistosomiasis or Soil Transmitted Helminthes (STH), supplementation could be not sufficient. The aim of this study was to evaluate the effects of deworming, on hemoglobin concentration, in children from 2 to 15 years, from Bengo.
Resumo:
Os comportamentos diádicos são os alicerces da qualidade da relação entre os pais e a criança, e estas relações precoces são determinantes para a organização da personalidade e para o desenvolvimento da criança. Neste estudo, pretendemos descrever os comportamentos diádicos detalhadamente e em seguida categorizá-los, no intuito de comparar os modos (tipo de jogo usado, respostas verbais, tipo de contato físico) e as funções (qualidade da comunicação) da interação mãe-filho(a) e pai-filho(a). Utilizamos uma amostra de 20 díades com bebés de 15 meses (5 meninos e 5 meninas), de termo e sem condições assinaláveis de risco. As díades foram filmadas em situação de jogo livre, mãe-filho(a) e pai-filho(a) independentemente. As interações transcritas (método de narrativas), submetidas a uma grelha de análise por nós construída, permitiram o estudo quantitativo e qualitativo das interações. Os resultados apontam para a existência de caraterísticas diferentes nas interações dos pais e das mães quando brincam com os seus filhos, sendo as demaior relevo: a) as mães utilizam mais a linguagem verbal que os pais; b) os pais utilizam mais a linguagem não-verbal que as mães; c) as mães têm uma comunicação não-verbal mais expressiva; d) as mães têm tendência para estruturar o ambiente de jogo; e) os pais têm tendência para dar instruções verbais sobre o funcionamento dos brinquedos.
Resumo:
This paper presents the implementation of the OFDM demodulator and the Viterbi decoder, proposed as part of a wireless High Definition video receiver to be integrated in an FPGA. These blocks were implemented in a Xilinx Virtex-6 FPGA. The complete system was previously modeled and simulated using MATLAB/Simulink to extract importante hardware characteristics for the FPGA implementation.
Resumo:
Eucalyptus globulus sapwood and heartwood showed no differences in lignin content (23.0% vs. 23.7%) and composition: syringyl-lignin (17.9% vs. 18.0%) and guaiacyl-lignin (4.8% vs. 5.2%). Delignification kinetics of S- and G-units in heartwood and sapwood was investigated by Py-GC–MS/FID at 130, 150 and 170 °C and modeled as double first-order reactions. Reactivity differences between S and G-units were small during the main pulping phase and the higher reactivity of S over G units was better expressed in the later pulping stage. The residual lignin composition in pulps was different from wood or from samples in the initial delignification stages, with more G and H-units. S/G ratio ranged from 3 to 4.5 when pulp residual lignin was higher than 10%, decreasing rapidly to less than 1. The S/H was initially around 20 (until 15% residual lignin), decreasing to 4 when residual lignin was about 3%.
Resumo:
A study of chemical transformations of cork during heat treatments was made using colour variation and FTIR analysis. The cork enriched fractions from Quercus cerris bark were subjected to isothermal heating in the temperature range 150–400 ◦C and treatment time from 5 to 90 min. Mass loss ranged from 3% (90 min at 150 ◦C) to 71% (60 min at 350 ◦C). FTIR showed that hemicelluloses were thermally degraded first while suberin remained as the most heat resistant component. The change of CIE-Lab parameters was rapid for low intensity treatments where no significant mass loss occurred (at 150 ◦C L* decreased from the initial 51.5 to 37.3 after 20 min). The decrease in all colour parameters continued with temperature until they remained substantially constant with over 40% mass loss. Modelling of the thermally induced mass loss could be made using colour analysis. This is applicable to monitoring the production of heat expanded insulation agglomerates.
Resumo:
Dissertação apresentada à Escola Superior de Educação de Lisboa para a obtenção do grau de Mestre em Intervenção Precoce
Resumo:
Copper iron (Cu-Fe) 3D porous foams for supercapacitor electrodes were electrodeposited in the cathodic regime, on stainless steel current collectors, using hydrogen bubbling dynamic template. The foams were prepared at different current densities and deposition times. The foams were submitted to thermal conditioning at temperatures of 150 and 250 degrees C. The morphology, composition and structure of the formed films were studied by SEM, EDS and XRD, respectively. The electrochemical behaviour was studied by cyclic voltammetry, electrochemical impedance spectroscopy and chronopotentiometry. The morphology of the 3D Cu-Fe foams is sensitive to the electrodeposition current and time. The increase of the current density produces a denser, larger and more ramified dendritic structure. Thermal conditioning at high temperature induces a coarser grain structure and the formation of copper oxides, which affect the electrochemical behaviour. The electrochemical response reveals the presence of various redox peaks assigned to the oxidation and reduction of Cu and Fe oxides and hydroxides in the foams. The specific capacitance of the 3D Cu Fe foams was significantly enhanced by thermal conditioning at 150 degrees C. The highest specific capacitance values attained 297 Fg(-1) which are much above the ones typically observed for single Cu or Fe Oxides and hydroxides. These values highlight a synergistic behaviour resulting from the combination of Cu and Fe in the form of nanostructured metallic foams. Moreover, the capacitance retention observed in an 8000 charge/discharge cycling test was above 66%, stating the good performance of these materials and its enhanced electrochemical response as supercapacitor negative electrodes. (C) 2014 Elsevier B.V. All rights reserved.