Influence of specimens' design and manufacturing process on microtensile bond strength to enamel: laboratory and FEA comparison

This study evaluated the effect of specimens' design and manufacturing process on microtensile bond strength, internal stress distributions (Finite Element Analysis - FEA) and specimens' integrity by means of Scanning Electron Microscopy (SEM) and Laser Scanning Confocal Microscopy (LCM). Excite was applied to flat enamel surface and a resin composite build-ups were made incrementally with 1-mm increments of Tetric Ceram. Teeth were cut using a diamond disc or a diamond wire, obtaining 0.8 mm² stick-shaped specimens, or were shaped with a Micro Specimen Former, obtaining dumbbell-shaped specimens (n = 10). Samples were randomly selected for SEM and LCM analysis. Remaining samples underwent microtensile test, and results were analyzed with ANOVA and Tukey test. FEA dumbbell-shaped model resulted in a more homogeneous stress distribution. Nonetheless, they failed under lower bond strengths (21.83 ± 5.44 MPa)c than stick-shaped specimens (sectioned with wire: 42.93 ± 4.77 MPaª; sectioned with disc: 36.62 ± 3.63 MPa b), due to geometric irregularities related to manufacturing process, as noted in microscopic analyzes. It could be concluded that stick-shaped, nontrimmed specimens, sectioned with diamond wire, are preferred for enamel specimens as they can be prepared in a less destructive, easier, and more precise way.

Intrinsic colony conditions affect the provisioning and oviposition process in the stingless bee Melipona scutellaris

The cell provisioning and oviposition process (POP) is a unique characteristic of stingless bees (Meliponini), in which coordinated interactions between workers and queen regulate the filling of brood cells with larval resources and subsequent egg laying. Environmental conditions seem to regulate reproduction in stingless bees; however, little is known about how the amount of food affects quantitative sequences of the process. We examined intrinsic variables by comparing three colonies in distinct conditions (strong, intermediate and weak state). We predicted that some of these variables are correlated with temporal events of POP in Melipona scutellaris colonies. The results demonstrated that the strong colony had shorter periods of POP.

Valve friction and nonlinear process model closed-loop identification

Among several process variability sources, valve friction and inadequate controller tuning are supposed to be two of the most prevalent. Friction quantification methods can be applied to the development of model-based compensators or to diagnose valves that need repair, whereas accurate process models can be used in controller retuning. This paper extends existing methods that jointly estimate the friction and process parameters, so that a nonlinear structure is adopted to represent the process model. The developed estimation algorithm is tested with three different data sources: a simulated first order plus dead time process, a hybrid setup (composed of a real valve and a simulated pH neutralization process) and from three industrial datasets corresponding to real control loops. The results demonstrate that the friction is accurately quantified, as well as ""good"" process models are estimated in several situations. Furthermore, when a nonlinear process model is considered, the proposed extension presents significant advantages: (i) greater accuracy for friction quantification and (ii) reasonable estimates of the nonlinear steady-state characteristics of the process. (C) 2010 Elsevier Ltd. All rights reserved.

Obtaining and selection of hexokinases-less strains of Saccharomyces cerevisiae for production of ethanol and fructose from sucrose

Saccharomyces cerevisiae hexokinase-less strains were produced to study the production of ethanol and fructose from sucrose. These strains do not have the hexokinases A and B. Twenty-three double-mutant strains were produced, and then, three were selected for presenting a smaller growth in yeast extract-peptone-fructose. In fermentations with a medium containing sucrose (180.3 g L-1) and with cell recycles, simulating industrial conditions, the capacity of these mutant yeasts in inverting sucrose and fermenting only glucose was well characterized. Besides that, we could also see their great tolerance to the stresses of fermentative recycles, where fructose production (until 90 g L-1) and ethanol production (until 42.3 g L-1) occurred in cycles of 12 h, in which hexokinase-less yeasts performed high growth (51.2% of wet biomass) and viability rates (77% of viable cells) after nine consecutive cycles.

Development and Characterization of L-Alanyl-L-Glutamine Containing Pellets employing Extrusion-Spheronization Method and Drying Process in Fluidized Bad Equipment.

Development and Characterization of L-Alanyl-L-Glutamine Containing Pellets employing Extrusion-Spheronization Method and Drying Process in Fluidized Bad Equipment"". In this work, five formulations of L-alanyl-L-glutamine (glutamine dipeptide) containing pellets with different drug concentration were developed and evaluated: F1 (9.07%); F2 (17.70%); F3 (27.98%); F4 (37.74%) e F5 (47.53%). Pellets were prepared by extrusion-spheronization method and, further, dried in fluidized bad equipment. The following assays were carried out with the batches obtained: granulometry, friability, true density and morphologic analysis. Between the five formulations evaluated, pellets obtained from F3 present best yield (75.80%), most uniform particle size distribution (89.67% of pellets with size in the range of 0.80 to 1.18), most high true density (2.1634 g/ml) and best aspect (1.0795 +/- 0.0410). Due to these features, pellets obtained from F3 were considered adequate to further polymeric coating process in order to produce a multiparticulate system to prolong L-alanyl-L-glutamine release.

Amphetamine modulates cellular recruitment and airway reactivity in a rat model of allergic lung inflammation

Asthma is characterized by pulmonary cellular infiltration, vascular exudation and airway hyperresponsiveness. Several drugs that modify central nervous system (CNS) activity can modulate the course of asthma. Amphetamine (AMPH) is a highly abused drug that presents potent stimulating effects on the CNS and has been shown to induce behavioral, biochemical and immunological effects. The purpose of this study was to investigate the effects of AMPH on pulmonary cellular influx, vascular permeability and airway reactivity. AMPH effects on adhesion molecule expression, IL-10 and IL-4 release and mast cell degranulation were also studied. Male Wistar rats were sensitized with ovalbumin (OVA) plus alum via subcutaneous injection. One week later, the rats received another injection of OVA-alum (booster). Two weeks after this booster, the rats were subjected to AMPH treatment 12 h prior to the OVA airway challenge. In rats treated with AMPH, the OVA challenge reduced cell recruitment into the lung, the vascular permeability and the cellular expression of ICAM-1 and Mac-1. Additionally, elevated levels of IL-10 and IL-4 were found in samples of lung explants from allergic rats. AMPH treatment, in comparison, increased IL-10 levels but reduced those of IL-4 in the lung explants. Moreover, the tracheal responsiveness to methacholine (MCh), as well as to an in vitro OVA challenge, was reduced by AMPH treatment, and levels of PCA titers were not modified by the drug. Our findings suggest that single AMPH treatment down-regulates several parameters of lung inflammation, such as cellular migration, vascular permeability and tracheal responsiveness. These results also indicate that AMPH actions on allergic lung inflammation include endothelium-leukocyte interaction mechanisms, cytokine release and mast cell degranulation. (C) 2010 Elsevier Ireland Ltd. All rights reserved.

Immunophenotyping and remodeling process in small airways of idiopathic interstitial pneumonias: functional and prognostic significance

Background and Aims: To test whether different degrees of immunologic and fibrotic airway remodeling processes occur in idiopathic interstitial pneumonias (IIPs), with impact on functional tests and survival, we studied the collagen/elastic system and immune cell density in the bronchiolar interstitium of lungs with the major types of IIPs. Materials and Methods: Histochemistry, immunohistochemistry and morphometric analysis were used to evaluate collagen/elastic fibers and immune cells in the bronchiolar interstitium of open lung biopsies of patients with cryptogenic organizing pneumonia [COP/organizing pneumonia (OP) = 10], acute interstitial pneumonia [AIP/diffuse alveolar damage (DAD) = 20], nonspecific interstitial pneumonia (NSIP/NSIP = 20) and idiopathic pulmonary fibrosis/usual interstitial pneumonia (UIP) = 20. Results: OP lungs presented a significant increase in collagenous/elastic fibers and in the total density of immune cells in the bronchiolar interstitium compared to controls, DAD, NSIP and UIP. We observed a significant increase in CD4, CD8 and CD20 lymphocytes, as well as in neutrophils, macrophages and plasma cells in OP. The increased amount of elastic fibers in the bronchiolar interstitium from OP lungs has a direct association with forced vital capacity (FVC) (r(s) = 0.99, P = 0.03). The most important survival predictor was CD20+ lymphocytes in the bronchiolar interstitium. In decreasing order, patients with UIP [Odds Ratio (OR) = 35.01], high forced expiratory volume in 1 s (FEV1)/FVC FVC (OR = 7.01), increased CD20+ lymphocytes (OR = 4.44) and collagenous/elastic fiber densities (OR = 2.03 and OR = 1.49, respectively) in the bronchiolar interstitium were those who had the greatest risk of death, followed by those with AIP, NSIP and COP. Conclusion: Different degrees of immunologic and fibroelastotic airway remodeling processes occur in the major types of IIPs with impact on physiological tests and survival.

Differential effects of female sex hormones on cellular recruitment and tracheal reactivity after formaldehyde exposure

Female sex hormones (FSHs) exert profound regulatory effects on the course of lung inflammation due to allergic and non-allergic immune responses. As pollution is one of the pivotal factors to induce lung dysfunction, in this study we investigated the modulatory role of FSHs on lung inflammation after a formaldehyde (FA) exposure. For this purpose, lung and systemic inflammatory responses were evaluated in terms of leukocytes countings in bronchoalveolar lavage (BAL), peripheral blood and bone marrow lavage from 7-day ovariectomized (OVx) and Sham-OVx rats subjected to FA inhalation for 3 consecutive days. The hypothesized link between effects of FSHs on expression of adhesion molecules and mast cells degranulation was also studied. Once exposed to FA, Sham-OVx rats increased the number of total cells recovered in BAL and of leukocytes in peripheral blood, and decreased the counts in bone marrow. By contrast, in OVx rats upon FA exposure there was a reduction of the total cells counts in BAL and of blood leukocytes: lung expressions of ICAM-1 and Mac-1 were depressed, but the number of bone marrow cells did not vary. Estradiol treatment of OVx rats increased the total cells in BAL and decreased the number of blood leukocytes, whereas the number of bone marrow cell remained unaltered. Progesterone treatment, in turn increased the total cells in BAL and blood leukocytes, but decreased the number of bone marrow cells. OVx rats exposed to FA developed tracheal hyperresponsiveness to methacholine (MCh). A similarly altered response was found between the tracheal segments of Sham-OVx rats after FA exposure and that found in tracheae of naive rats. Estradiol treatment prevented FA-induced tracheal hyperresponsiveness to MCh whereas progesterone was ineffective in this regard. In addition, OVx rats upon FA exposure significantly increased both, the ability of mast cell degranulation and serum corticosterone levels. In conclusion, it was found that FSHs act by distinct control mechanisms on FA-induced lung inflammation and tracheal hyperresponsiveness, since at low circulating levels of FSHs (such as those after OVx) there is some resistance to the development of a lung inflammatory response, but the cholinergic tracheal responsiveness is exacerbated. Our data also help to understand the involvement of FSHs on mast cells activity after pollutants exposure and add information regarding the role of FSHs on the mechanisms related to endothelium-leukocyte interactions. (C) 2011 Elsevier Ireland Ltd. All rights reserved.

Prediction of dynamical, nonlinear, and unstable process behavior

Process scheduling techniques consider the current load situation to allocate computing resources. Those techniques make approximations such as the average of communication, processing, and memory access to improve the process scheduling, although processes may present different behaviors during their whole execution. They may start with high communication requirements and later just processing. By discovering how processes behave over time, we believe it is possible to improve the resource allocation. This has motivated this paper which adopts chaos theory concepts and nonlinear prediction techniques in order to model and predict process behavior. Results confirm the radial basis function technique which presents good predictions and also low processing demands show what is essential in a real distributed environment.

The pattern recognition receptors Nod1 and Nod2 account for neutrophil recruitment to the lungs of mice infected with Legionella pneumophila

The intracellular bacterium Legionella pneumophila induces a severe form of pneumonia called Legionnaires diseases, which is characterized by a strong neutrophil (NE) infiltrate to the lungs of infected individuals. Although the participation of pattern recognition receptors, such as Toll-like receptors, was recently demonstrated, there is no information on the role of nod-like receptors (NLRs) for bacterial recognition in vivo and for NE recruitment to the lungs. Here, we employed a murine model of Legionnaires disease to evaluate host and bacterial factors involved in NE recruitment to the mice lungs. We found that L. pneumophila type four secretion system, known as Dot/Icm, was required for NE recruitment as dot/icm mutants fail to trigger NE recruitment in a process independent of bacterial multiplication. By using mice deficient for Nod1, Nod2, and Rip2, we found that these receptors accounted for NE recruitment to the lungs of infected mice. In addition, Rip2-dependent responses were important for cytokine production and bacterial clearance. Collectively, these studies show that Nod1, Nod2, and Rip2 account for generation of innate immune responses in vivo, which are important for NE recruitment and bacterial clearance in a murine model of Legionnaires diseases. (C) 2010 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

The Process of Simulation Authoring/Creation by Chemistry Teachers: A Service Learning Experience

Two case studies are presented to describe the process of public school teachers authoring and creating chemistry simulations. They are part of the Virtual Didactic Laboratory for Chemistry, a project developed by the School of the Future of the University of Sao Paulo. the documental analysis of the material produced by two groups of teachers reflects different selection process for both themes and problem-situations when creating simulations. The study demonstrates the potential for chemistry learning with an approach that takes students' everyday lives into account and is based on collaborative work among teachers and researches. Also, from the teachers' perspectives, the possibilities of interaction that a simulation offers for classroom activities are considered.

Reconfiguration of distribution networks to minimize loss and disruption costs using genetic algorithms

In this paper a computational implementation of an evolutionary algorithm (EA) is shown in order to tackle the problem of reconfiguring radial distribution systems. The developed module considers power quality indices such as long duration interruptions and customer process disruptions due to voltage sags, by using the Monte Carlo simulation method. Power quality costs are modeled into the mathematical problem formulation, which are added to the cost of network losses. As for the EA codification proposed, a decimal representation is used. The EA operators, namely selection, recombination and mutation, which are considered for the reconfiguration algorithm, are herein analyzed. A number of selection procedures are analyzed, namely tournament, elitism and a mixed technique using both elitism and tournament. The recombination operator was developed by considering a chromosome structure representation that maps the network branches and system radiality, and another structure that takes into account the network topology and feasibility of network operation to exchange genetic material. The topologies regarding the initial population are randomly produced so as radial configurations are produced through the Prim and Kruskal algorithms that rapidly build minimum spanning trees. (C) 2009 Elsevier B.V. All rights reserved.

Effects of the preventive and corrective adjustments in economical designs for online process control for attributes with misclassification errors

The procedure for online process control by attributes consists of inspecting a single item at every m produced items. It is decided on the basis of the inspection result whether the process is in-control (the conforming fraction is stable) or out-of-control (the conforming fraction is decreased, for example). Most articles about online process control have cited the stoppage of the production process for an adjustment when the inspected item is non-conforming (then the production is restarted in-control, here denominated as corrective adjustment). Moreover, the articles related to this subject do not present semi-economical designs (which may yield high quantities of non-conforming items), as they do not include a policy of preventive adjustments (in such case no item is inspected), which can be more economical, mainly if the inspected item can be misclassified. In this article, the possibility of preventive or corrective adjustments in the process is decided at every m produced item. If a preventive adjustment is decided upon, then no item is inspected. On the contrary, the m-th item is inspected; if it conforms, the production goes on, otherwise, an adjustment takes place and the process restarts in-control. This approach is economically feasible for some practical situations and the parameters of the proposed procedure are determined minimizing an average cost function subject to some statistical restrictions (for example, to assure a minimal levelfixed in advanceof conforming items in the production process). Numerical examples illustrate the proposal.

Gastro-resistant Pellets of Didanosine obtained by Extrusion and Spheronization: Assessing the Production Process

The aim this work was develop gastro-resistant pellets of didanosine as well as study the impact on the pellets properties, regarding the way as the binder was added and drying process used. The pellets formation was accompanied by analysis of morphological parameters and didanosine dissolution. In the most cases, pellets showed diameter around 1.0 mm and shape parameters acceptable. The variations of the process did not interfere significantly in pellets size. In turn, drying in fluid bed favored the dissolution of didanosine, in contrast to binder addition on powder form that impaired. In another hand, this last resulted in the best aspect factor (about 1.1). Gastro-resistant pellets showed adequate dissolution, compatible with this type of dosage form. The variables of process studied enabled obtain pellets with characteristics of shape and dissolution just slightly different, indicating flexibility of the formulation for production of gastro-resistant pellets of didanosine.

Are supplier selection criteria going green? Case studies of companies in Brazil

Purpose - The purpose of this paper is to verify if Brazilian companies are adopting environmental requirements in the supplier selection process. Further, this paper intends to analyze whether there is a relation between the level of environmental management maturity and the inclusion of environmental criteria in the companies` selection of suppliers. Design/methodology/approach - A review of mainstream literature on environmental management, traditional criteria in the supplier selection process and the incorporation of environmental requirements in this context. The empirical study`s strategy is based on five Brazilian case studies with industrial companies. Face-to-face interviews and informal conversations are to be held, explanations made by e-mail with representatives from the purchasing, environmental management, logistics and other areas, and observation and the collection of company documents are also employed. Findings - Based on the cases, it is concluded that companies still use traditional criteria to select suppliers, such as quality and cost, and do not adopt environmental requirements in the supplier selection process in a uniform manner. Evidence found shows that the level of environmental management maturity influences the depth with which companies adopt environmental criteria when selecting suppliers. Thus, a company with more advanced environmental management adopts more formal procedures for selecting environmentally appropriate suppliers than others. Originality/value - This is the first known study to verify if Brazilian companies are adopting environmental requirements in the supplier selection process.