Surface tension of flotation solution and its influence on the selectivity of the separation between apatite and gangue minerals

This work presents and discusses the influence of the surface tension (gamma(LV)) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at approximate to 51.0 mN/m. The critical surface tension of wettability (gamma(C)) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, , and it was 33.9 mN/m when determined by Zisman`s approach.

Separation of silica from bauxite via froth flotation

This paper reports an innovative development: concentrating gibbsite via reverse froth flotation in order to obtain a metallurgical-grade bauxite concentrate. Tailings from an industrial plant have undergone attrition scrubbing and desliming; the quartz silica contained in the tailings has undergone flotation. Starch was used as a depressant, and ether-amine as the cationic collector. Optimum pH is around 10.0. In pilot plant scale, a metallurgical-grade concentrate was obtained by assaying 42.3% available alumina with an alumina/insoluble silica mass ratio of 11.1. It contained the gibbsite and the iron and titanium bearing minerals. The concentrate was further upgraded by magnetic separation, leading to 54.0% available alumina, with an alumina/insoluble silica mass ratio of 12.6 at an overall available alumina recovery of 69.3% in the final concentrate (non-magnetic product). (C) 2008 Elsevier Ltd. All rights reserved.

A Separation Principle for the Continuous-Time LQ-Problem With Markovian Jump Parameters

In this paper, we devise a separation principle for the finite horizon quadratic optimal control problem of continuous-time Markovian jump linear systems driven by a Wiener process and with partial observations. We assume that the output variable and the jump parameters are available to the controller. It is desired to design a dynamic Markovian jump controller such that the closed loop system minimizes the quadratic functional cost of the system over a finite horizon period of time. As in the case with no jumps, we show that an optimal controller can be obtained from two coupled Riccati differential equations, one associated to the optimal control problem when the state variable is available, and the other one associated to the optimal filtering problem. This is a separation principle for the finite horizon quadratic optimal control problem for continuous-time Markovian jump linear systems. For the case in which the matrices are all time-invariant we analyze the asymptotic behavior of the solution of the derived interconnected Riccati differential equations to the solution of the associated set of coupled algebraic Riccati equations as well as the mean square stabilizing property of this limiting solution. When there is only one mode of operation our results coincide with the traditional ones for the LQG control of continuous-time linear systems.

Metal separation from mixed types of batteries using selective precipitation and liquid-liquid extraction techniques

The purpose of this paper is to study metal separation from a sample composed of a mixture of the main types of spent household batteries, using a hydrometallurgical route, comparing selective precipitation and liquid-liquid extraction separation techniques. The preparation of the solution consisted of: grinding the waste of mixed batteries, reduction and volatile metals elimination using electric furnace and acid leaching. From this solution two different routes were studied: selective precipitation with sodium hydroxide and liquid-liquid extraction using Cyanex 272 [bis(2,4,4-trimethylpentyl) phosphoric acid] as extracting agent. The best results were obtained from liquid-liquid extraction in which Zn had a 99% extraction rate at pH 2.5. More than 95% Fe was extracted at pH 7.0, the same pH at which more than 90% Ce was extracted. About 88% Mn, Cr and Co was extracted at this pH. At pH 3.0, more than 85% Ni was extracted, and at pH 3.5 more than 80% of Cd and La was extracted. (C) 2010 Elsevier Ltd. All rights reserved.

Using Reverberation to Improve Range and Elevation Discrimination for Small Array Sound Source Localization

Sound source localization (SSL) is an essential task in many applications involving speech capture and enhancement. As such, speaker localization with microphone arrays has received significant research attention. Nevertheless, existing SSL algorithms for small arrays still have two significant limitations: lack of range resolution, and accuracy degradation with increasing reverberation. The latter is natural and expected, given that strong reflections can have amplitudes similar to that of the direct signal, but different directions of arrival. Therefore, correctly modeling the room and compensating for the reflections should reduce the degradation due to reverberation. In this paper, we show a stronger result. If modeled correctly, early reflections can be used to provide more information about the source location than would have been available in an anechoic scenario. The modeling not only compensates for the reverberation, but also significantly increases resolution for range and elevation. Thus, we show that under certain conditions and limitations, reverberation can be used to improve SSL performance. Prior attempts to compensate for reverberation tried to model the room impulse response (RIR). However, RIRs change quickly with speaker position, and are nearly impossible to track accurately. Instead, we build a 3-D model of the room, which we use to predict early reflections, which are then incorporated into the SSL estimation. Simulation results with real and synthetic data show that even a simplistic room model is sufficient to produce significant improvements in range and elevation estimation, tasks which would be very difficult when relying only on direct path signal components.

Effect of Charge Asymmetry on Adsorption and Phase Separation of Polyampholytes on Silica and Cellulose Surfaces

The relation between the properties of polyampholytes in aqueous solution and their adsorption behaviors on silica and cellulose surfaces was investigated. Four polyampholytes carrying different charge densities but with the same nominal ratio of positive to negative segments and two structurally similar polyelectrolytes (a polyacid and a polybase) were investigated by using quartz crystal microgravimetry using silica-coated and cellulose-coated quartz resonators. Time-resolved mass and rigidity (or viscoelasticity) of the adsorbed layer was determined from the shifts in frequency (Delta f) and energy dissipation (Delta D) of the respective resonator. Therefore, elucidation of the dynamics and extent of adsorption, as well as the conformational changes of the adsorbed macromolecules, were possible. The charge properties of the solid Surface played a crucial role in the adsorption of the studied polyampholytes, which was explained by the capability of the surface to polarize the polyampholyte at the interface. Under the same experimental conditions, the polyampholytes had a higher nominal charge density phase-separated near the interface, producing a soft, dissipative, and loosely bound layer. In the case of cellulose substrates, where adsorption was limited, electrostatic and polarization effects were concluded to be less significant.

Analysis of source-follower buffers implemented with graded-channel SOI nMOSFETs operating at cryogenic temperatures

This work studies the operation of source-follower buffers implemented with standard and graded-channel (GC) fully depleted (FD) SCI nMOSFETs at low temperatures. The analysis is performed by comparing the voltage gain of buffers implemented with GC and standard SOI nMOS transistors considering devices with the same mask channel length and same effective channel length. It is shown that the use of GC devices allows for achieving improved gain in all inversion levels in a wide range of temperatures. In addition, this improvement increases as temperature is reduced. It is shown that GC transistors can provide virtually constant gain, while for standard devices, the gain departs from the maximum value depending on the temperature and inversion level imposed by the bias current and input voltage. Two-dimensional numerical simulations were performed in order to study the reasons for the enhanced gain of GC MOSFETs at low temperatures. (C) 2009 Elsevier Ltd. All rights reserved.

Nonlinear Interactions in a Piezoceramic Bar Transducer Powered by a Vacuum Tube Generated by a Nonideal Source

Interactions between the oscillations of piezoceramic transducer and the mechanism of as excitation-the generator of the electric current of limited power-supply-are analyzed in this paper In practical situations, the dynamics of the forcing function on a vibrating system cannot be considered as given a priori, and it must be taken as a consequence of the dynamics of the whole system. In other words, the forcing source has limited power as that provided by a dc motor for an example, and thus its own dynamics is influenced by that of the vibrating system being forced. This increases the number of degrees of freedom of the problem, and it is called a nonideal problem. In this work, we present certain phenomena as Sommerfeld effect, jump, saturation, and stability, through the influences of the parameters of the governing equations motion. [DOI: 10.1115/1.3007909]

Advantages of graded-channel SOI nMOSFETs for application as source-follower analog buffer

In this work the performance of graded-channel (CC) SOI MOSFETs operating as source-follower buffers is presented. The experimental analysis is performed by comparing the gain and linearity of buffers implemented with CC and standard SOI MOS devices considering the same mask dimensions. It is shown that by using CC devices, buffer gain very close to the theoretical limit can be achieved, with improved linearity, while for standard devices the gain departs from the theoretical value depending on the inversion level imposed by the bias current and input voltage. Two-dimensional numerical simulations were performed in order to confirm some hypotheses proposed to explain the gain behavior observed in the experimental data. By using numerical simulations the channel length has been varied, showing that the gain of buffers implemented with CC devices remains close to the theoretical limit even when short-channel devices are adopted. It has also been shown that the length of a source-follower buffer using CC devices can be reduced by a factor of 5, in comparison with a standard Sol MOSFET, without gain loss or linearity degradation. (C) 2008 Elsevier Ltd. All rights reserved.

Mate (Ilex paraguariensis) as a source of water extractable antioxidant for use in chicken meat

Aqueous extract of mate, made from dried leaves of Ilex paraguariensis, St. Hilaire, was shown to be effective during chilled storage for up to 10 days in protecting lipids and vitamin E against oxidation in pre-cooked meat balls made from chicken breast added 0.5% salt and packed in atmospheric air. Extracts made with water, methanol, ethanol or 70% aqueous acetone were evaluated by comparing (1) total phenolic content, (2) radical scavenging capacity, (3) effect on lipid oxidation in a food emulsion model, and in liposomes. Based on the three-step evaluation, aqueous mate extract was preferred for food use. Dried leaves were further compared to dried rosemary leaves in chicken meat balls, and mate (0.05 and 0.10%) found to yield equal or better protection than rosemary at the same concentration against formation of secondary lipid oxidation products.

Influence of ethylene on carotenoid biosynthesis during papaya postharvesting ripening

The carotenoid composition was evaluated during ripening of papaya cv. `Golden` under untreated (control) conditions and treated with ethylene and 1-methylcyclopropene (1-MCP). At the end of the experiments, the total carotenoid content in the control group (2194.4 mu g/100 g) was twice as high as that found in ethylene (1018.1 mu g/100 g) and 1-MCP (654.5 mu g/100 g) gas-treated samples. Separation of 21 carotenoids by HPLC connected to photodiode array and mass spectrometry detectors showed that no minor carotenoids seemed to be particularly favoured by the treatments. Lycopene was the major carotenoid in all untreated and gas-treated samples, ranging from 461.5 to 1321.6 mu g/100 g at the end of the experiments. According to the proposed biosynthetic pathway, lycopene is the central compound, since it is the most abundant carotenoid indicating a high stimulation of its upstream steps during ripening, and it is the source for the synthesis of other derivative compounds, such as beta-cryptoxanthin. The influence of both gas treatments on the carotenoid biosynthetic pathway was considered. (C) 2011 Elsevier Inc. All rights reserved.

Effects of isoflavone-supplemented soy yogurt on lipid parameters and atherosclerosis development in hypercholesterolemic rabbits: a randomized double-blind study

Background: There is increasing interest in natural treatments to control dyslipidemia and reduce the risk of cardiovascular disease. Previous studies have demonstrated the beneficial effects of soy yogurt fermented with Enterococcus faecium CRL 183 and of dietary isoflavones on the lipid profile. The purpose of the present study was to investigate the effects of isoflavone-supplemented soy yogurt, fermented with E. faecium CRL183, on lipid parameters and atherosclerosis development in rabbits with induced hypercholesterolemia. Methods: Forty-eight rabbits were randomly assigned to eight groups fed on the following diets for 60 days: C - control; IY - isoflavone-supplemented soy yogurt; H - hypercholesterolemic (1.0% cholesterol wt/wt diet); HY - hypercholesterolemic plus soy yogurt; HIY - hypercholesterolemic plus isoflavone-supplemented soy yogurt; HP - hypercholesterolemic plus placebo; HI hypercholesterolemic plus isoflavone and HE - hypercholesterolemic plus pure culture of E. faecium CRL 183. Serum lipids and autoantibodies against oxLDL (oxLDL Ab) were analyzed on days 0, 30 and 60 of the treatment and the atherosclerotic lesions were quantified at the end of the experiment. Results: Soy yogurt, soy yogurt supplemented with isoflavones and placebo promoted significant reductions in total cholesterol level (38.1%, 27.0% and 26.6%, respectively). Significant increases in serum HDL-C concentration relative to group H were detected in animals that ingested soy yogurt, with or without the isoflavone supplement (55.2%), E. faecium culture (43.3%) or placebo (35.8%). Intake of soy yogurt and soy yogurt supplemented with isoflavones prevented the rise of oxLDL Ab during the study period. The extent of atherosclerosis in the thoracic and abdominal aortas was reduced in the HIY, HY and HP groups. However, when the whole aorta was analyzed, animals treated with soy yogurt supplemented with isoflavones exhibited the greatest reduction (51.4%, P < 0.05) in atherosclerotic lesion area, compared to group H. Conclusion: Soy yogurt could be consumed as an alternative means of reducing the risk of cardiovascular disease by improving the lipid profile and inhibiting oxLDL Ab formation. Our findings also suggest that isoflavone supplementation may enhance the antiatherosclerotic effect of soy yogurt.

Separation of Steroids and the Determination of Estradiol Content in Transdermic Patches by Microemulsion Electrokinetic Chromatography

A novel microemulsion electrokinetic capillary chromatography (MEEKC) method has been developed which separates a range of nine steroids. A microemulsion containing ethyl acetate, butan-1-ol, sodium dodecyl sulfate, 15% (v/v) acetonitrile and 12 mmol L(-1) sodium tetraborate aqueous buffer at pH 9.2 was used with direct UV detection at 200 nm. The method was validated for the determination of 17 beta-estradiol content, a hormone steroid, in transdermal patches. Adequate sensitivity (DL = 0.88 mu g mL(-1); QL = 2.65 mu g mL(-1)) without interference from sample excipients was obtained. 17 beta-Estradiol migrates in approximately 5.4 min. Estrone was used as internal standard and acceptable precision (< 1.2% RSD), linearity (r = 0.9996; range from 40.0 to 60.0 mu g mL(-1)), and recovery (100.4 +/- A 0.9% at three concentration levels) were obtained. The principal advantage of the method is that it is rapid and avoids the need of time consuming and expensive sample pre-treatment steps.

Double-blind, randomized, placebo-controlled trial of a cream containing the Stryphnodendron adstringens (Martius) Coville bark extract for suppressing terminal hair growth

Background Excess of terminal hair can be defined as excessive hair that appears in male-like pattern in women. Some experts consider this condition as a result of an atypical relationship between levels of circulating androgens and sensitivity of androgen receptors in hair follicles to circulating androgens. Aims The aim of this research work was to evaluate the efficacy of a topical treatment for suppressing terminal hair growth of a cream containing 6.0% of the Stryphnodendron adstringens bark extract. Study design and subjects Study was randomized, double-blind and placebo-controlled. Subjects with excess of terminal hair were randomized to placebo and to the active treatment (cream with 6.0% of the extract). Evaluation was performed before and after 6 months, and subjects were photographed in each time. Clinical examination was carried out with the same physicians and in accordance with the Ferriman-Gallwey (FG) score. Results Benefits of the cream containing S. adstringens bark extract was observed in 60.98% (P < 0.001) of the subjects. FG score changed from 4 to 3 in the placebo group compared to 4-2 in the active. The cream suppressed the terminal hair growth and diminished the number of terminal hair. Subjects also described the reduction of skin hyperpigmentation, folliculitis and acne. Adverse events were not verified by physicians or patients. Conclusions The cream with 6.0% of the S. adstringens bark extract was effective on the reduction and on the reversion of the terminal hair excess, being considered a new promissory product for such finality.

Development and validation of sensitive methods for determination of sibutramine hydrochloride monohydrate and direct enantiomeric separation on a protein-based chiral stationary phase

Sibutramine hydrochloride monohydrate, chemically 1-(4-chlorophenyl)-N,N-dimethyl-alpha-(2-methylpropyl) hydrochloride monohydrate (SB center dot HCl center dot H2O), was approved by the U.S. Food and Drug Administration for the treatment of obesity. The objective of this study was to develop, validate, and compare methods using UV-derivative spectrophotometry (UVDS) and reversed-phase high-performance liquid chromatography (HPLC) for the determination of SB center dot HCl center dot H2O in pharmaceutical drug products. The UVDS and HPLC methods were found to be rapid, precise, and accurate. Statistically, there was no significant difference between the proposed UVDS and HPLC methods. The enantiomeric separation of SB was obtained on an alpha-1 acid glycoprotein column. The R- and S-sibutramine were eluted in < 5 min with baseline separation of the chromatographic peaks (alpha = 1.9 and resolution = 1.9).