Low-frequency noise and static analysis of the impact of the TiN metal gate thicknesses on n- and p-channel MuGFETs

The impact of the titanium nitride (TIN) gate electrode thickness has been investigated in n and p channel SOI multiple gate field effect transistors (MuGFETs) through low frequency noise charge pumping and static measurements as well as capacitance-voltage curves The results suggest that a thicker TIN metal gate electrode gives rise to a higher EOT a lower mobility and a higher interface trap density The devices have also been studied for different back gate biases where the GIFBE onset occurs at lower front-gate voltage for thinner TIN metal gate thickness and at higher V(GF) In addition it is demonstrated that post deposition nitridation of the MOCVD HfSiO gate dielectric exhibits an unexpected trend with TIN gate electrode thickness where a continuous variation of EOT and an increase on the degradation of the interface quality are observed (C) 2010 Elsevier Ltd All rights reserved

Analyzing static three-dimensional elastic domains with a new infinite boundary element formulation

A new two-dimensionally mapped infinite boundary element (IBE) is presented. The formulation is based on a triangular boundary element (BE) with linear shape functions instead of the quadrilateral IBEs usually found in the literature. The infinite solids analyzed are assumed to be three-dimensional, linear-elastic and isotropic, and Kelvin fundamental solutions are employed. One advantage of the proposed formulation over quadratic or higher order elements is that no additional degrees of freedom are added to the original BE mesh by the presence of the IBEs. Thus, the IBEs allow the mesh to be reduced without compromising the accuracy of the result. Two examples are presented, in which the numerical results show good agreement with authors using quadrilateral IBEs and analytical solutions. (C) 2010 Elsevier Ltd. All rights reserved.

An alternative multi-region BEM technique for three-dimensional elastic problems

The main objective of this work is to present an alternative boundary element method (BEM) formulation for the static analysis of three-dimensional non-homogeneous isotropic solids. These problems can be solved using the classical boundary element formulation, analyzing each subregion separately and then joining them together by introducing equilibrium and displacements compatibility. Establishing relations between the displacement fundamental solutions of the different domains, the alternative technique proposed in this paper allows analyzing all the domains as one unique solid, not requiring equilibrium or compatibility equations. This formulation also leads to a smaller system of equations when compared to the usual subregion technique, and the results obtained are even more accurate. (C) 2008 Elsevier Ltd. All rights reserved.

Transport-Regional Equity Issue Revisited

Almeida E. S. de, Haddad E. A. and Hewings G. J. D. Transport-regional equity issue revisited, Regional Studies. The objective of this paper is to analyse the relationship between transport and regional equity in Minas Gerais, Brazil. Furthermore, the existence of a trade-off between economic performance and regional equity is investigated as well. To do so, the paper develops a spatial computable general equilibrium model based on Brocker and Schneider`s approach of 2002 to implement comparative static analysis, explicitly incorporating iceberg transportation costs. Four activities are modelled, namely production, final demand, transportation and exports. Two production factors are assumed: labour and other factors. The model has 12 domestic regions and three external regions. Four counterfactual experiments are developed based on decreases in transportation costs due to a `distance shortening`. The main findings indicate that if the transport infrastructure improvement is focused only among poor regions, the promotion of regional equity is insignificant. If the transport infrastructure improvement links are concentrated among rich regions, there is an increase in regional income inequalities. However, if the improvements are targeted to the roads linking poor regions and rich ones, there is greater promotion of regional equity. The same result will occur when improvements are made to all road links of the state. [image omitted] Almeida E. S. de, Haddad E. A. et Hewings G. J. D. La question du rapport entre le transport et l`equilibre regional vue sous un jour nouveau, Regional Studies. Cet article cherche a analyser le rapport entre le transport et l`equilibre regional en Minas Gerais au Bresil. En outre, on examine la presence d`un echange entre la performance economoique et l`equilibre regional. Pour le faire, on construit un modele geographique de l`equilibre general a utiliser sur ordinateur fonde sur l`approche de Brockner et Schneider en 2002 afin de mettre en oeuvre une analyse statique comparative qui comprend explicitement les frais de transport iceberg. On modelise quatre activites, a savoir, la production, la demande finale, le transport et l`exportation. On fait deux suppositions quant aux facteurs de production: la main-d`oevre et d`autres facteurs. Le modele embrasse douze regions internes et trois regions externes. On fait quatre experiences paradoxales fondees sur la baisse des frais de transport due a une `reduction des distances`. Les principaux resultats indiquent que si l`amelioration de l`equipement de transport ne porte que sur les regions defavorisees, la promotion de l`equilibre regional s`avere negligeable. Si l`amelioration de l`equipement de transport focalise les regions riches, il s`avere un creusement des ecarts des revenus regionaux. Cependant, si les ameliorations ciblent les routes qui relient les regions defavorisees aux regions riches, il s`avere une plus grande promotion de l`equilibre regional. Il en va de meme pour la situation ou on a apporte des amenagements a toutes les liaisons routieres de l`etat. Modele geographique de l`equilibre general a utiliser sur ordinateur Equilibre regional Peformance economique Frais de transport Almeida E. S. de, Haddad E. A. und Hewings G. J. D. Die Wiederaufnahme der Frage von Verkehrswesen im Verhaltnis zu regionaler Fairness, Regional Studies. Dieser Aufsatz beabsichtigt, die Beziehung zwischen Verkehrswesen und regionaler Fairness in Minas Gerais (Brasilien) zu analysieren und zugleich auch das Vorkommen von Einbussen entweder bei wirtschaftlicher Leistung der regionaler Fairness zu untersuchen. Zu diesem Zwecke wird ein auf dem Ansatz von Brocker und Schneider (2002) aufbauendes raumliches komputables allgemeines Gleichgewichtsmodell entwickelt, um vergleichende statistische Analysen durchzufuhren, wobei verborgene `Eisberg`-Transportkosten ausdrucklich berucksichtigt werden. Es werden vier Unternehmenstatigk eiten aufgefuhrt: Herstellung, Nachfrage, Transportwesen und Exporte, und zwei Produktionsfaktoren vorausgesetzt: Arbeitskrafte und andere Faktoren. Das Modell umfasst zwolf Inlandsregionen und drei externe Regionen. Es werden vier gegensatzliche Experimente entwickelt, die auf einer Abnahme der Transportkosten infolge einer `Verkurzung der Entfernungen` beruhen. Die Hauptbefunde weisen darauf hin, dass die Forderung regionaler Fairness unbedeutend bleibt, wenn die Verbesserungen der Transportinfrastruktur sich nur auf minderbemittelte Regionen konzentrieren; werden die Verbesserungen der Verbindungen der Transportinfrastruktur in wohlhabenden Regionen durchgefuhrt, so nehmen regionale Einkommensunterschiede zu. Wenn die Verbesserungen jedoch auf Strassen abzielen, die wohlhabende Regionen mit weniger bemittelten verbinden, wird regionale Fairness starker gefordert. Das gleiche Ergebnis wird sich einstellen, wenn Verbesserungen an allen Strassenverbindungen des Staates vorgenommen werden. Raumliches, komputables, allgemeines Gleichgewichtsmodell Regionale Fairness Wirtschaftsleistung Transportkosten Almeida E. S. de, Haddad E. A. y Hewings G. J. D. Revisando el tema de la igualdad del transporte en las regiones, Regional Studies. El objetivo de este documento es analizar la relacion entre el transporte y la igualdad regional en Minas Gerais, Brasil. Asimismo investigamos la existencia de una compensacion entre el rendimiento economico y la igualdad regional. Para ello desarrollamos un modelo de equilibrio general computable y espacial basado en el enfoque de Brocker y Schneider en 2002 para hacer un analisis estatico y comparativo, explicitamente incorporando los costes ocultos de transporte. Se modelan cuatro actividades: la produccion, la demanda final, el transporte y las exportaciones. Suponemos que existen dos factores de produccion: mano de obra y otros factores. En este modelo, existen doce regiones internas y tres regiones externas. Desarrollamos cuatro experimentos contrafactuales basados en la disminucion de los costes de transporte debido a una `acortamiento de las distancias`. Los principales resultados indican que si la mejora de la infraestructura del transporte se centra solo entre las regiones mas pobres, el fomento de la igualdad regional es insignificante. Si los enlaces de la mejora de la infraestructura del transporte se concentran en las regiones ricas, aumentan las desigualdades de ingresos regionales. Sin embargo, si se mejoran los enlaces de carreteras entre las regiones pobres y ricas, se fomenta mejor la igualdad regional. El mismo resultado ocurre cuando se mejoran los enlaces de todas las carreteras del estado. Modelo de equilibrio general computable y espacial Igualdad regional Rendimiento economico Costes de transporte.

Interface shear strength of geosynthetics: Evaluation and analysis of inclined plane tests

The inclined plane test (IPT) is commonly performed to measure the interface shear strength between different materials as those used in cover systems of landfills. The test, when interpreted according to European test Standards provides the static interface friction angle, usually assumed for 50 mm displacement and denoted as phi(stat)(50). However, if interpreted considering the several phases of the sliding process, the test is capable of yielding more realistic information about the interface shear strength such as differentiating interfaces which exhibit the same value of phi(stat)(50) but different behavior for displacement less than 50 mm. In this paper, the IPT is used to evaluate the interface shear strength of some materials usually present in cover liner systems of landfill. The results of the tests were analyzed for both, the static and the dynamic phases of the sliding and were interpreted based on the static initial friction angle, phi(0), and the limit friction angle, phi(lim). It is shown that depending on the sliding behavior of the interfaces, phi(stat)(50), which is usually adopted as the designing parameter in stability analysis, can be larger than phi(0) and phi(lim). (C) 2009 Elsevier Ltd. All rights reserved.

A hybrid-mixed finite element formulation for the geometrically exact analysis of three-dimensional framed structures

This paper addresses the development of a hybrid-mixed finite element formulation for the quasi-static geometrically exact analysis of three-dimensional framed structures with linear elastic behavior. The formulation is based on a modified principle of stationary total complementary energy, involving, as independent variables, the generalized vectors of stress-resultants and displacements and, in addition, a set of Lagrange multipliers defined on the element boundaries. The finite element discretization scheme adopted within the framework of the proposed formulation leads to numerical solutions that strongly satisfy the equilibrium differential equations in the elements, as well as the equilibrium boundary conditions. This formulation consists, therefore, in a true equilibrium formulation for large displacements and rotations in space. Furthermore, this formulation is objective, as it ensures invariance of the strain measures under superposed rigid body rotations, and is not affected by the so-called shear-locking phenomenon. Also, the proposed formulation produces numerical solutions which are independent of the path of deformation. To validate and assess the accuracy of the proposed formulation, some benchmark problems are analyzed and their solutions compared with those obtained using the standard two-node displacement/ rotation-based formulation.

A comparison of dynamic and quasi-static results for the flow towards a well

The present analysis takes into account the acceleration term in the differential equation of motion to obtain exact dynamic solutions concerning the groundwater flow towards a well in a confined aquifer. The results show that the error contained in the traditional quasi-static solution is very small in typical situations.

Void fraction measurement and signal analysis from multiple-electrode impedance sensors

Void fraction sensors are important instruments not only for monitoring two-phase flow, but for furnishing an important parameter for obtaining flow map pattern and two-phase flow heat transfer coefficient as well. This work presents the experimental results obtained with the analysis of two axially spaced multiple-electrode impedance sensors tested in an upward air-water two-phase flow in a vertical tube for void fraction measurements. An electronic circuit was developed for signal generation and post-treatment of each sensor signal. By phase shifting the electrodes supplying the signal, it was possible to establish a rotating electric field sweeping across the test section. The fundamental principle of using a multiple-electrode configuration is based on reducing signal sensitivity to the non-uniform cross-section void fraction distribution problem. Static calibration curves were obtained for both sensors, and dynamic signal analyses for bubbly, slug, and turbulent churn flows were carried out. Flow parameters such as Taylor bubble velocity and length were obtained by using cross-correlation techniques. As an application of the void fraction tested, vertical flow pattern identification could be established by using the probability density function technique for void fractions ranging from 0% to nearly 70%.

Evaluation of flow regimes in a semi-cylindrical spouted bed through statistical, mutual information, spectral and Hurst`s analysis

Hydrodynamic studies were conducted in a semi-cylindrical spouted bed column of diameter 150 mm, height 1000 mm, conical base included angle of 60 degrees and inlet orifice diameter 25 mm. Pressure transducers at several axial positions were used to obtain pressure fluctuation time series with 1.2 and 2.4 mm glass beads at U/U-ms from 0.3 to 1.6, and static bed depths from 150 to 600 mm. The conditions covered several flow regimes (fixed bed, incipient spouting, stable spouting, pulsating spouting, slugging, bubble spouting and fluidization). Images of the system dynamics were also acquired through the transparent walls with a digital camera. The data were analyzed via statistical, mutual information theory, spectral and Hurst`s Rescaled Range methods to assess the potential of these methods to characterize the spouting quality. The results indicate that these methods have potential for monitoring spouted bed operation.

GLOBAL POSTURAL REEDUCATION AND STATIC STRETCHING EXERCISES IN THE TREATMENT OF MYOGENIC TEMPOROMANDIBULAR DISORDERS: A RANDOMIZED STUDY

Objective: The purpose of this study was to compare 2 different interventions, global postural reeducation (GPR) and static stretching exercises (SS), in the treatment of women with temporomandibular disorders (TMDs). Methods: A total of 28 subjects with TMDs were randomized into 2 treatment groups: GPR, where therapy involved muscle global chain stretching, or SS, with conventional static stretching; but only 24 completed the study. Eight treatment sessions lasting 40 minutes each (weekly) were performed. Assessments were conducted at baseline, immediately after treatment end, and 2 months later. Measurements included pain intensity at the temporomandibular joint, headache, cervicalgia, teeth clenching, ear symptoms, restricted sleep, and difficulties for mastication, using a visual analogue scale. In addition, electromyographic activity and pain thresholds were measured at the masseter, anterior temporalis, stemocleidomastoid, and upper trapezius muscles. Two-way analysis of variance with Tukey post hoc test was used for between-group comparisons. Significance level was .05. Results: Comparing the pain assessments using the visual analogue scale, no significant differences were seen with the exception of severity of headaches at treatment end (GPR, 3.92 +/- 2.98 cm; SS, 1.64 +/- 1.66 cm; P < .024). In addition, no significant differences were seen for pain thresholds and for electromyographic activity (P > .05). Conclusions: For the subjects in this study, both GPR and SS were similarly effective for the treatment of TMDs with muscular component. They equally reduced pain intensity, increased pain thresholds, and decreased electromyographic activity. (J Manipulative Physiol Ther 2010;33:500-507)

Photoelastic Stress Analysis of Different Designs of Cement-Retained Fixed Partial Dentures on Morse Taper Oral Implants

There is no consensus in literature regarding the best plan for prosthetic rehabilitation with partial multiple adjacent implants to minimize stress generated in the bone-implant interface. The aim of this study was to evaluate the biomechanical behavior of cemented fixed partial dentures, splinted and nonsplinted, on Morse taper implants and with different types of coating material (ceramic and resin), using photoelastic stress analysis. A photoelastic model of an interposed edentulous space, missing a second premolar and a first molar, and rehabilitated with 4 different types of cemented crowns and supported by 2 adjacent implants was used. Groups were as follows: UC, splinted ceramic crowns; IC, nonsplinted ceramic crowns; UR, splinted resin crowns; and IR, nonsplinted resin crowns. Different vertical static loading conditions were performed: balanced occlusal load, 10 kgf; simultaneous punctiform load on the implanted premolar and molar, 10 kgf; and alternate punctiform load on the implanted premolar and molar, 5 kgf. Changes in stress distribution were analyzed in a polariscope, and digital photographs were taken of each condition to allow comparison of stress pattern distribution around the implants. Cementation of the fixed partial dentures generated stresses between implants. Splinted restorations distributed the stresses more evenly between the implants than nonsplinted when force was applied. Ceramic restorations presented better distribution of stresses than resin restorations. Based on the results obtained, it was concluded that splinted ceramic restorations promote better stress distribution around osseointegrated implants when compared with nonsplinted crowns; metal-ceramic restorations present less stress concentration and magnitude than metal-plastic restorations.

The comparative field body temperature among Liolaemus lizards: Testing the static and the labile hypotheses

Two competing hypotheses have been suggested to explain thermal sensitivity of lizards to environmental conditions. These are the static and the labile hypotheses. The static hypothesis posits that thermal physiology is evolutionary conservative and consequently relatively insensitive to directional selection. Contrarily, the labile hypothesis states that thermal physiology does respond readily to directional selection in some lizard taxa. In this paper, we tested both hypotheses among species of Liolaemus lizards. The genus Liolaemus is diverse with about 200 species, being broadly distributed from central Peru to Tierra del Fuego at the southern end of South America. Data of field body temperature (T(b)) from Liolaemus species were collected from the literature. Based on the distributional range of the species we also collected data of mean annual ambient temperatures. We observed that both the traditional analysis and the phylogenetic approach indicate that in the genus Liolaemus T(b) of species varies in a manner that is consistent with ecological gradient of ambient temperature. The data suggest that the thermal physiology of Liolaemus lizards is evolutionarily flexible, and that this plasticity has been partially responsible for the colonization of a wide array of thermal environments. (C) 2009 Elsevier Ltd. All rights reserved.

Evaluation of superficial microhardness in dental enamel with different eruptive ages

This study evaluated the superficial microhardness of enamel in teeth at different posteruptive ages (before eruption in the oral cavity, 2-3 years after eruption, 4-10 years after eruption and more than 10 years after eruption). The study sample was composed of 134 specimens of human enamel. One fragment of each tooth was obtained from the flattest central portion of the crown to produce specimens with 3 x 3 mm. The enamel blocks were minimally flattened out and polished in order to obtain a flat surface parallel to the base, which is fundamental for microhardness testing. Microhardness was measured with a microhardness tester and a Knoop diamond indenter, under a static load of 25 g applied for 5 seconds. Comparison between the superficial microhardness obtained for the different groups was performed by analysis of Student's t test. The results demonstrated that superficial microhardness values have a tendency to increase over the years, with statistically significant difference only between unerupted enamel and that with more than 10 years after eruption. According to the present conditions and methodology, it was concluded that there were differences between the superficial micro-hardness of specimens at different eruptive ages, revealing an increasing mineralization. However, this difference was significant only between unerupted specimens and those with more than 10 years after eruption.

Digital subtraction radiographic analysis of the combination of bioabsorbable membrane and bovine morphogenetic protein pool in human periodontal infrabony defects

OBJECTIVES: This study assessed the bone density gain and its relationship with the periodontal clinical parameters in a case series of a regenerative therapy procedure. MATERIAL AND METHODS: Using a split-mouth study design, 10 pairs of infrabony defects from 15 patients were treated with a pool of bovine bone morphogenetic proteins associated with collagen membrane (test sites) or collagen membrane only (control sites). The periodontal healing was clinically and radiographically monitored for six months. Standardized pre-surgical and 6-month postoperative radiographs were digitized for digital subtraction analysis, which showed relative bone density gain in both groups of 0.034 ± 0.423 and 0.105 ± 0.423 in the test and control group, respectively (p>0.05). RESULTS: As regards the area size of bone density change, the influence of the therapy was detected in 2.5 mm² in the test group and 2 mm² in the control group (p>0.05). Additionally, no correlation was observed between the favorable clinical results and the bone density gain measured by digital subtraction radiography (p>0.05). CONCLUSIONS: The findings of this study suggest that the clinical benefit of the regenerative therapy observed did not come with significant bone density gains. Long-term evaluation may lead to a different conclusions.

T-wave alternans: desempenho clínico, limitações, metodologias de análise

Reconhecer com precisão indivíduos com maior risco imediato de morte súbita cardíaca (MSC) ainda é uma questão em aberto. A natureza fortuita dos eventos cardiovasculares agudos não parece se adequar ao conhecido modelo de indução de taquicardia/fibrilação ventricular por um gatilho em sincronia a um substrato arritmogênico estático. Quanto ao mecanismo da MSC, uma instabilidade elétrica dinâmica explicaria melhor a raridade da associação simultânea de um gatilho certo a um substrato cardíaco apropriado. Diversos estudos tentaram medir essa instabilidade elétrica cardíaca (ou um equivalente válido) em uma sequência de batimentos cardíacos no ECG. Dentre os mecanismos possíveis podemos citar o prolongamento do QT, dispersão do QT, potenciais tardios, alternância de onda T ou T-wave alternans (TWA), e turbulência da frequência cardíaca. Este artigo se atém em particular ao papel da TWA no panorama atual da estratificação de risco cardíaco. Os achados sobre TWA ainda são heterogêneos, variando de um desempenho prognóstico muito bom até um quase nulo, dependendo da população clínica observada e protocolo clínico usado. Para preencher as atuais lacunas no conhecimento sobre TWA, profissionais médicos e pesquisadores devem explorar melhor as características técnicas das diversas tecnologias disponíveis para a avaliação de TWA e atentar ao fato de que os valores de TWA respondem a diversos outros fatores, além de medicamentos. Informações sobre mecanismos celulares e subcelulares da TWA estão fora do escopo deste artigo, mas são referenciados alguns dos principais trabalhos sobre este tópico, com o intuito de auxiliar no entendimento dos conceitos e fatos cobertos neste artigo.