A new chemorheological analysis of highly filled thermosets used in integrated circuit packaging

Chemorheology (and thus process modeling) of highly filled thermosets used in integrated circuit (IC) packaging has been complicated by their highly filled nature, fast kinetics of curing, and viscoelastic nature. This article summarizes a more thorough chemorheological analysis of a typical IC packaging thermoset material, including novel isothermal and nonisothermal multiwave parallel-plate chemorheology. This new chemorheological analysis may be used to optimize existing and design new IC packaging processes. (C) 1997 John Wiley & Sons, Inc.

Analysis of the gate capacitance measurement technique and its application for the evaluation of hot-carrier degradation in submicrometer MOSFETs

The use of gate-to-drain capacitance (C-gd) measurement as a tool to characterize hot-carrier-induced charge centers in submicron n- and p-MOSFET's has been reviewed and demonstrated. By analyzing the change in C-gd measured at room and cryogenic temperature before and after high gate-to-drain transverse field (high field) and maximum substrate current (I-bmax) stress, it is concluded that the degradation was found to be mostly due to trapping of majority carriers and generation of interface states. These interface states were found to be acceptor states at top half of band gap for n-MOSFETs and donor states at bottom half of band gap for p-MOSFETs. In general, hot electrons are more likely to be trapped in gate oxide as compared to hot holes while the presence of hot holes generates more interface states. Also, we have demonstrated a new method for extracting the spatial distribution of oxide trapped charge, Q(ot), through gate-to-substrate capacitance (C-gb) measurement. This method is simple to implement and does not require additional information from simulation or detailed knowledge of the device's structure. (C) 2001 Elsevier Science Ltd. All rights reserved.

The Winnipeg principles, WTO and sustainable development: Proposed policies for reconciling trade and the environment

There is, a widespread belief that the WTO has made virtually no concessions to environmentalists about their concerns arising from free trade and the process of globalization. There are concerns that these processes may undermine prospects for sustainable development. Following, the United Nations Conference on Environment and Development held in Rio de Janeiro in 1992, the International Institute for Sustainable Development was established to advocate policies to support sustainable development within Canada and globally. In 1994, it proposed the Winnipeg Principles as. a means for reconciling international trade and development so as to: achieve sustainable development (ISD, 1994a,b). These seven principles are outlined in this article and assessed:. Although the International Institute for Sustainable Development had hoped: through these principles to influence the work programme of the Environment and Trade Committee of WTO, it seems to have little effect. Probably if these principles had been seriously considered by WTO, the serious social conflicts which emerged globally at the beginning of this century would have been avoided, and we would be in a better position to understand the complex links between trade, environment and sustainable development and adopt relevant policies. Copyright (C) 2001 John Wiley & Sons, Ltd and ERP Environment.

Dopant extraction from scanning capacitance microscopy measurements of p-n junctions using combined inverse modeling and forward simulation

This article proposes a more accurate approach to dopant extraction using combined inverse modeling and forward simulation of scanning capacitance microscopy (SCM) measurements on p-n junctions. The approach takes into account the essential physics of minority carrier response to the SCM probe tip in the presence of lateral electric fields due to a p-n junction. The effects of oxide fixed charge and interface state densities in the grown oxide layer on the p-n junction samples were considered in the proposed method. The extracted metallurgical and electrical junctions were compared to the apparent electrical junction obtained from SCM measurements. (C) 2002 American Institute of Physics.

Theoretical and experimental studies of unbraced tubular trusses allowing for torsional stiffness

This paper describes the buckling phenomenon of a tubular truss with unsupported length through a full-scale test and presents a practical computational method for the design of the trusses allowing for the contribution of torsional stiffness against buckling, of which the effect has never been considered previously by others. The current practice for the design of a planar truss has largely been based on the linear elastic approach which cannot allow for the contribution of torsional stiffness and tension members in a structural system against buckling. The over-simplified analytical technique is unable to provide a realistic and an economical design to a structure. In this paper the stability theory is applied to the second-order analysis and design of the structural form, with detailed allowance for the instability and second-order effects in compliance with design code requirements. Finally, the paper demonstrates the application of the proposed method to the stability design of a commonly adopted truss system used in support of glass panels in which lateral bracing members are highly undesirable for economical and aesthetic reasons.