Electromechanical properties of engineered lead free potassium sodium niobate based materials

K0.5Na0.5NbO3 (KNN), is the most promising lead free material for substituting lead zirconate titanate (PZT) which is still the market leader used for sensors and actuators. To make KNN a real competitor, it is necessary to understand and to improve its properties. This goal is pursued in the present work via different approaches aiming to study KNN intrinsic properties and then to identify appropriate strategies like doping and texturing for designing better KNN materials for an intended application. Hence, polycrystalline KNN ceramics (undoped, non-stoichiometric; NST and doped), high-quality KNN single crystals and textured KNN based ceramics were successfully synthesized and characterized in this work. Polycrystalline undoped, non-stoichiometric (NST) and Mn doped KNN ceramics were prepared by conventional ceramic processing. Structure, microstructure and electrical properties were measured. It was observed that the window for mono-phasic compositions was very narrow for both NST ceramics and Mn doped ceramics. For NST ceramics the variation of A/B ratio influenced the polarization (P-E) hysteresis loop and better piezoelectric and dielectric responses could be found for small stoichiometry deviations (A/B = 0.97). Regarding Mn doping, as compared to undoped KNN which showed leaky polarization (P-E) hysteresis loops, B-site Mn doped ceramics showed a well saturated, less-leaky hysteresis loop and a significant properties improvement. Impedance spectroscopy was used to assess the role of Mn and a relation between charge transport – defects and ferroelectric response in K0.5Na0.5NbO3 (KNN) and Mn doped KNN ceramics could be established. At room temperature the conduction in KNN which is associated with holes transport is suppressed by Mn doping. Hence Mn addition increases the resistivity of the ceramic, which proved to be very helpful for improving the saturation of the P-E loop. At high temperatures the conduction is dominated by the motion of ionized oxygen vacancies whose concentration increases with Mn doping. Single crystals of potassium sodium niobate (KNN) were grown by a modified high temperature flux method. A boron-modified flux was used to obtain the crystals at a relatively low temperature. XRD, EDS and ICP analysis proved the chemical and crystallographic quality of the crystals. The grown KNN crystals exhibit higher dielectric permittivity (29,100) at the tetragonal-to-cubic phase transition temperature, higher remnant polarization (19.4 μC/cm2) and piezoelectric coefficient (160 pC/N) when compared with the standard KNN ceramics. KNN single crystals domain structure was characterized for the first time by piezoforce response microscopy. It could be observed that <001> - oriented potassium sodium niobate (KNN) single crystals reveal a long range ordered domain pattern of parallel 180° domains with zig-zag 90° domains. From the comparison of KNN Single crystals to ceramics, It is argued that the presence in KNN single crystal (and absence in KNN ceramics) of such a long range order specific domain pattern that is its fingerprint accounts for the improved properties of single crystals. These results have broad implications for the expanded use of KNN materials, by establishing a relation between the domain patterns and the dielectric and ferroelectric response of single crystals and ceramics and by indicating ways of achieving maximised properties in KNN materials. Polarized Raman analysis of ferroelectric potassium sodium niobate (K0.5Na0.5)NbO3 (KNN) single crystals was performed. For the first time, an evidence is provided that supports the assignment of KNN single crystals structure to the monoclinic symmetry at room temperature. Intensities of A′, A″ and mixed A′+A″ phonons have been theoretically calculated and compared with the experimental data in dependence of crystal rotation, which allowed the precise determination of the Raman tensor coefficients for (non-leaking) modes in monoclinic KNN. In relation to the previous literature, this study clarifies that assigning monoclinic phase is more suitable than the orthorhombic one. In addition, this study is the basis for non-destructive assessments of domain distribution by Raman spectroscopy in KNN-based lead-free ferroelectrics with complex structures. Searching a deeper understanding of the electrical behaviour of both KNN single crystal and polycrystalline materials for the sake of designing optimized KNN materials, a comparative study at the level of charge transport and point defects was carried out by impedance spectroscopy. KNN single crystals showed lower conductivity than polycrystals from room temperature up to 200 ºC, but above this temperature polycrystalline KNN displays lower conductivity. The low temperature (T < 200 ºC) behaviour reflects the different processing conditions of both ceramics and single crystals, which account for less defects prone to charge transport in the case of single crystals. As temperature increases (T > 200 ºC) single crystals become more conductive than polycrystalline samples, in which grain boundaries act as barriers to charge transport. For even higher temperatures the conductivity difference between both is increased due to the contribution of ionic conduction in single crystals. Indeed the values of activation energy calculated to the high temperature range (T > 300 ºC) were 1.60 and 0.97 eV, confirming the charge transport due to ionic conduction and ionized oxygen vacancies in single crystals and polycrystalline KNN, respectively. It is suggested that single crystals with low defects content and improved electromechanical properties could be a better choice for room temperature applications, though at high temperatures less conductive ceramics may be the choice, depending on the targeted use. Aiming at engineering the properties of KNN polycrystals towards the performance of single crystals, the preparation and properties study of (001) – oriented (K0.5Na0.5)0.98Li0.02NbO3 (KNNL) ceramics obtained by templated grain growth (TGG) using KNN single crystals as templates was undertaken. The choice of KNN single crystals templates is related with their better properties and to their unique domain structure which were envisaged as a tool for templating better properties in KNN ceramics too. X-ray diffraction analysis revealed for the templated ceramics a monoclinic structure at room temperature and a Lotgering factor (f) of 40% which confirmed texture development. These textured ceramics exhibit a long range ordered domain pattern consisting of 90º and 180º domains, similar to the one observed in the single crystals. Enhanced dielectric (13017 at TC), ferroelectric (2Pr = 42.8 μC/cm2) and piezoelectric (d33 = 280 pC/N) properties are observed for textured KNNL ceramics as compared to the randomly oriented ones. This behaviour is suggested to be due to the long range ordered domain patterns observed in the textured ceramics. The obtained results as compared with the data previously reported on texture KNN based ceramics confirm that superior properties were found due to ordered repeated domain pattern. This study provides an useful approach towards properties improvement of KNN-based piezoelectric ceramics. Overall, the present results bring a significant contribution to the pool of knowledge on the properties of sodium potassium niobate materials: a relation between the domain patterns and di-, ferro-, and piezo-electric response of single crystals and ceramics was demonstrated and ways of engineering maximised properties in KNN materials, for example by texturing were established. This contribution is envisaged to have broad implications for the expanded use of KNN over the alternative lead-based materials.

Structural characterization and biological activity of polysaccharides from infusions used in the popular tradition

The use of plants with medicinal purposes is an ancient practice still very common in developing regions, and is rapidly spreading in industrialized countries. This fact is evidenced by the large number of ethnobotanical studies found in the literature referring that these plants are often used as decoctions and infusions. In most studies the reported biological activities are attributed to the presence of phenolic compounds, due to their antioxidant properties, and to polysaccharides, with its anti-tumoral properties. In “Trás-os-Montes” region, some of the most popular infusions used by the popular medicine are prepared with the dried leaves of Fraxinus angustifolia, the dried shoots of Mentha suaveolens, and the dried inflorescences of Pterospartum tridentatum. However, there are no studies about the polysaccharides present in these infusions. Thus, through the structural characterization of the polysaccharides present in the infusions of F. angustifolia, M. suaveolens, and P. tridentatum, the present PhD thesis intends to evaluate the possible relation between polysaccharides and the immunostimulatory activity that these infusions might present. In a preliminary phase, infusions of F. angustifolia were prepared according to the popular tradition, and it was observed that the obtained water soluble material contained approximately 85% of material non-retained in C18 cartridges, with hydrophilic characteristics, with the remaining 15% comprising retained-material with hydrophobic characteristics. It was also shown that the infusions only contained between 2 and 4% of high molecular weight material (HMWM), which comprised approximately 30% of carbohydrate material. Sugar and methylation analysis of the HMWM suggested the presence of pectic polysaccharides, together with type II arabinogalactans, mannans, and xyloglucans. However, the amount of material obtained is to low for the fractionation, and structural analysis of the polysaccharides present. The 4 h decoction, divided in two periods of 2 h, with water renewal, allowed to increase the HMWM yield, relatively to the infusions traditional infusions. It was also observed that the decoction also allowed to increase the HMWM proportion of carbohydrate material, due to an increase in the proportion of uronic acid present, although the neutral sugar residues seemed to be detected in similar proportions. Therefore, in all the experiments subsequently performed, the HMWM used was obtained through the decoction of F. angustifolia dried leaves, M. suaveolens dried shoots, and P. tridentatum dried inflorescences. x After the fractionation, through ethanol precipitation, and anion exchange chromatography, of the polysaccharides from the HMWM obtained by the decoction of the vegetable material of the distinct studied plants, it was observed the presence of high proportions of pectic polysaccharides, containing type I arabinogalactans, together with minor proportions of type II arabinogalactans, mannans, and xyloglucans. The presence of pectic polysaccharides in the extracts from F. angustifolia was also evidenced through endo-polygalacturonase treatment, and ESI-MS and ESI-MS/MS experiments. The detection of linked pentose and uronic acid residues, also seemed to suggest the presence of xylogalacturonan domains in the pectic polysaccharides from F. angustifolia. The extracts from F. angustifolia dried leaves also contained type II arabinogalactans that exhibited a higher structural diversity than those detected in the M. suaveolens, and P. tridentatum extracts, particularly in the substitution degree of the galactan backbone, and in the extension of the (1→5)-Araf side chains. Moreover, for all the plants studied, it was also observed that the type II arabinogalactans, extracted during the 2nd 2h of the extraction process, exhibited a substitution degree of the galactan backbone higher than those extracted during the 1st 2h. The extracts from P. tridentatum dried inflorescences contained higher proportions of mannans, and also of xyloglucans, both presenting a substitution degree higher than those, which were detected in lower proportion in the extracts of F. angustifolia and M. suaveolens. Through ESI-MS and ESI-MS/MS it was possible to evidence that the mannans present in the extracts of P. tridentatum presented acetyl groups on the O-2 of the mannosyl residues. It was also evidenced that the P. tridentatum mannans were more extensively acetylated than the mannans detected in the coffee infusion, LBG, and other non-conventional mannan sources. Moreover, it was detected the presence of oligosaccharides comprising hexose residues linked to non acetylated pentose residues, suggesting the possible presence of arabinose residues in the mannans from P. tridentatum extracts. The immunostimulatory activity of three fractions isolated from the extracts of F. angustifolia, M. suaveolens, and P. tridentatum, was tested and an increase in the NO production by macrophages, without compromising their cellular viability, was observed. The type I, and type II arabinogalactans detected in the extracts from F. angustifolia, and M. suaveolens seem to have contributed for the observed immunostimulatory activity. For the fraction from P. tridentatum, the mannans acetylation, and the presence of type I, and type II arabinogalactans seemed to contribute for the macrophage immunostimulatory activity observed. The possible presence of storage xyloglucans from the inflorescences seeds, also seems to have contributed for the immunostimulatory activity registered when the macrophages were stimulated with higher extract concentrations. The results obtained allow to conclude that the extracts of F. angustifolia dried leaves, M. suaveolens dried shoots, and P. tridentatum dried inflorescences contained high proportions of pectic polysaccharides, exhibiting type I arabinogalactans, together with other polysaccharides, such as type II arabinogalactans, mannans, and xyloglucans. This polysaccharide mixture seems to have contributed to the immunostimulatory activity of fractions isolated from the extracts of the studied plants. Therefore, as the same type of polysaccharides seem to be present in the decoctions and in the infusions, it seems possible that the polysaccharides might contribute for the therapeutic properties frequently associated by the popular tradition to the infusions of these plants.

Surface reactivity enhancement of silica-based glass-ceramic scaffolds

A paradigm shift is taking place from using transplanting tissue and synthetic implants to a tissue engineering approach that aims to regenerate damaged tissues by combining cells from the body with highly porous scaffold biomaterials, which act as templates, guiding the growth of new tissue. The central focus of this thesis was to produce porous glass and glass-ceramic scaffolds that exhibits a bioactive and biocompatible behaviour with specific surface reactivity in synthetic physiological fluids and cell-scaffold interactions, enhanced by composition and thermal treatments applied. Understanding the sintering behaviour and the interaction between the densification and crystallization processes of glass powders was essential for assessing the ideal sintering conditions for obtaining a glass scaffolds for tissue engineering applications. Our main goal was to carry out a comprehensive study of the bioactive glass sintering, identifying the powder size and sintering variables effect, for future design of sintered glass scaffolds with competent microstructures. The developed scaffolds prepared by the salt sintering method using a 3CaO.P2O5 - SiO2 - MgO glass system, with additions of Na2O with a salt, NaCl, exhibit high porosity, interconnectivity, pore size distribution and mechanical strength suitable for bone repair applications. The replacement of 6 % MgO by Na2O in the glass network allowed to tailor the dissolution rate and bioactivity of the glass scaffolds. Regarding the biological assessment, the incorporation of sodium to the composition resulted in an inibition cell response for small periods. Nevertheless it was demonstrated that for 21 days the cells response recovered and are similar for both glass compositions. The in vitro behaviour of the glass scaffolds was tested by introducing scaffolds to simulated body fluid for 21 days. Energy-dispersive Xray spectroscopy and SEM analyses proved the existence of CaP crystals for both compositions. Crystallization forming whitlockite was observed to affect the dissolution behaviour in simulated body fluid. By performing different heat treatments, it was possible to control the bioactivity and biocompatability of the glass scaffolds by means of a controlled crystallization. To recover and tune the bioactivity of the glass-ceramic with 82 % crystalline phase, different methods have been applied including functionalization using 3- aminopropyl-triethoxysilane (APTES). The glass ceramic modified surface exhibited an accelerated crystalline hydroxyapatite layer formation upon immersion in SBF after 21 days while the as prepared glass-ceramic had no detected formation of calcium phosphate up to 5 months. A sufficient mechanical support for bone tissue regeneration that biodegrade later at a tailorable rate was achievable with the glass–ceramic scaffold. Considering the biological assessment, scaffolds demonstrated an inductive effect on the proliferation of cells. The cells showed a normal morphology and high growth rate when compared to standard culture plates. This study opens up new possibilities for using 3CaO.P2O5–SiO2–MgO glass to manufacture various structures, while tailoring their bioactivity by controlling the content of the crystalline phase. Additionally, the in vitro behaviour of these structures suggests the high potential of these materials to be used in the field of tissue regeneration.

Relações petrogénicas entre o complexo gnáissico migmático e o granito de Banabuiú (Nordeste do Brasil)

A região de Banabuiú situa-se no Domínio Ceará Central, na porção setentrional da Província Borborema, um dos cinturões orogénicos formados durante o evento Brasiliano/Pan-Africano no final do Neoproterozóico. As duas unidades litológicas principais presentes na área são: o complexo gnáissicomigmatítico (metapelitos e metagrauvaques) e granitóides brasilianos. Para além das formações paraderivadas, no substrato da região também foi identificado um conjunto de rochas ortoderivadas, até então não individualizado na cartografia existente. Tanto a sequência paraderivada, como os materiais ortoderivados, foram intensamente afectados por metamorfismo regional da fácies granulítica durante a Orogenia Brasiliana, que atingiu as condições de fusão parcial, gerando migmatitos com um amplo espectro de morfologias. Estes migmatitos apresentam estruturas dominantemente estromáticas, embora localmente se tenham identificado também corpos irregulares de diatexitos de tipo“schlieren”, “schollen” e “maciço (s.s)”, indicando que o processo de migmatização culminou com a produção de maiores quantidades de fundido. Em termos tectónicos, o basamento da região regista os efeitos de três fases de deformação, embora as estruturas concordantes à D3 sejam dominantes e obliterem, em muitos casos, as anisotropias anteriores. A maior parte dos fundidos anatécticos parece ter sido produzida durante tectónica transcorrente D3. No entanto, as condições metamórficas para o início da fusão parcial parece ter sido atingidas antes, durante a D2, já que também existem leucossomas, embora em proporções reduzidas, associados com as estruturas desta fase. A grande quantidade de volumes de leucossomas / veios leucocráticos encontrados na região, está relacionada com a actuação da zona de cisalhamento de Orós e parece corresponder a fundidos anatécticos gerados em níveis mais profundos que foram injectados nas sequências orto- e para-derivadas, devido a notória escassez de leucossomas “in situ” nestas rochas. A presença de fluidos aquosos injectados no complexo migmatítico de Banabuiú terá proporcionado a re-hidratação e retrogradação das rochas hospedeiras, evidenciada, essencialmente, pela presença de moscovite tardia, amplamente distribuída nos metassedimentos e ortognaisses, sobretudo nas zonas próximas aos leucossomas e veios leucocráticos. Dados isotópicos apontam que as rochas da região de Banabuiú apresentam valores fortemente negativos de εNdt e positivos de εSrt sugerindo um significativo envolvimento de materiais supracrustais do grupo Acopiara na formação do complexo migmatítico e na petrogénese do maciço granítico de Banabuiú e o marcado fraccionamento isotópico Sm-Nd observado nalguns dos leucossomas analisados indica que os líquidos anatécticos que lhes deram origem resultaram de processos de fusão em desequilíbrio, em condições anidras, e foram rapidamente extraídos da área-fonte, comprovando o carácter alóctone dos veios leucocráticos intercalados nos ortognaisses e paragnaisses de Banabuiú.

Extension of electrochemically active sites in SOFCs and SOECs

Solid oxide fuel (SOFCs) and electrolyzer (SOECs) cells have been promoted as promising technologies for the stabilization of fuel supply and usage in future green energy systems. SOFCs are devices that produce electricity by the oxidation of hydrogen or hydrocarbon fuels with high efficiency. Conversely, SOECs can offer the reverse reaction, where synthetic fuels can be generated by the input of renewable electricity. Due to this similar but inverse nature of SOFCs and SOECs, these devices have traditionally been constructed from comparable materials. Nonetheless, several limitations have hindered the entry of SOFCs and SOECs into the marketplace. One of the most debilitating is associated with chemical interreactions between cell components that can lead to poor longevities at high working temperatures and/or depleted electrochemcial performance. Normally such interreactions are countered by the introduction of thin, purely ionic conducting, buffer layers between the electrode and electrolyte interface. The objective of this thesis is to assess if possible improvements in electrode kinetics can also be obtained by modifying the transport properties of these buffer layers by the introduction of multivalent cations. The introduction of minor electronic conductivity in the surface of the electrolyte material has previously been shown to radically enhance the electrochemically active area for oxygen exchange, reducing polarization resistance losses. Hence, the current thesis aims to extend this knowledge to tailor a bi-functional buffer layer that can prevent chemical interreaction while also enhancing electrode kinetics.The thesis selects a typical scenario of an yttria stabilized zirconia electrolyte combined with a lanthanide containing oxygen electrode. Gadolinium, terbium and praseodymium doped cerium oxide materials have been investigated as potential buffer layers. The mixed ionic electronic conducting (MIEC) properties of the doped-cerium materials have been analyzed and collated. A detailed analysis is further presented of the impact of the buffer layers on the kinetics of the oxygen electrode in SOFC and SOEC devices. Special focus is made to assess for potential links between the transport properties of the buffer layer and subsequent electrode performance. The work also evaluates the electrochemical performance of different K2NiF4 structure cathodes deposited onto a peak performing Pr doped-cerium buffer layer, the influence of buffer layer thickness and the Pr content of the ceria buffer layer. It is shown that dramatic increases in electrode performance can be obtained by the introduction of MIEC buffer layers, where the best performances are shown to be offered by buffer layers of highest ambipolar conductivity. These buffer layers are also shown to continue to offer the bifunctional role to protect from unwanted chemical interactions at the electrode/electrolyte interface.

Diopside-fluorapatite-wollastonite based bioactive glasses and glass-ceramics

Bioactive glasses and glass–ceramics are a class of biomaterials which elicit special response on their surface when in contact with biological fluids, leading to strong bonding to living tissue. This particular trait along with good sintering ability and high mechanical strength make them ideal materials for scaffold fabrication. The work presented in this thesis is directed towards understanding the composition-structure-property relationships in potentially bioactive glasses designed in CaOMgOP2O5SiO2F system, in some cases with added Na2O. The main emphasis has been on unearthing the influence of glass composition on molecular structure, sintering ability and bioactivity of phosphosilicate glasses. The parent glass compositions have been designed in the primary crystallization field of the pseudo-ternary system of diopside (CaO•MgO•2SiO2) – fluorapatite (9CaO•3P2O5•CaF2) – wollastonite (CaO•SiO2), followed by studying the impact of compositional variations on the structure-property relationships and sintering ability of these glasses. All the glasses investigated in this work have been synthesized via melt-quenching route and have been characterized for their molecular structure, sintering ability, chemical degradation and bioactivity using wide array of experimental tools and techniques. It has been shown that in all investigated glass compositions the silicate network was mainly dominated by Q2 units while phosphate in all the glasses was found to be coordinated in orthophosphate environment. The glass compositions designed in alkali-free region of diopside – fluorapatite system demonstrated excellent sintering ability and good bioactivity in order to qualify them as potential materials for scaffold fabrication while alkali-rich bioactive glasses not only hinder the densification during sintering but also induce cytotoxicity in vitro, thus, are not ideal candidates for in vitro tissue engineering. One of our bioglass compositions with low sodium content has been tested successfully both in vivo and in preliminary clinical trials. But this work needs to be continued and deepened. The dispersing of fine glass particles in aqueous media or in other suitable solvents, and the study of the most important factors that affect the rheology of the suspensions are essential steps to enable the manufacture of porous structures with tailor-made hierarchical pores by advanced processing techniques such as Robocasting.

Characterisation of the cyclic behaviour of reinforced concrete elements with plain bars

Sismos recentes comprovam a elevada vulnerabilidade dos edifícios existentes de betão armado. A resposta das estruturas aos sismos é fortemente condicionada pelas características da aderência aço-betão, que exibe degradação das propriedades iniciais quando sujeitas a carregamentos cíclicos e alternados. Este fenómeno é ainda mais gravoso para elementos com armadura lisa, predominantes na maioria das estruturas construídas até à década de 70 nos países do sul da Europa. A prática corrente de conceção, dimensionamento e pormenorização das estruturas antigas leva a que tenham características de comportamento e níveis de segurança associados não compatíveis com as exigências atuais. Os estudos realizados sobre o comportamento cíclico de elementos estruturais de betão armado com armadura lisa são ainda insuficientes para a completa caracterização deste tipo de elementos. Esta tese visou a caraterização da relação tensão de aderência versus escorregamento para elementos estruturais com armadura lisa e o estudo da resposta cíclica de pilares e nós viga-pilar de betão armado com armadura lisa. Foram realizados dez séries de ensaios de arrancamento (nove monotónicos e um cíclico) em provetes com varões lisos. Os resultados destes ensaios permitiram propor novas expressões empíricas para a estimativa dos parâmetros usados num modelo disponível na literatura para representação da relação tensão de aderência versus escorregamento. É ainda proposto um novo modelo monotónico para a relação tensão de aderência versus escorregamento que representa melhor a resposta após a resistência máxima de aderência. Uma campanha de ensaios unidirecionais em pilares e nós viga-pilar foi também realizada com o objetivo principal de caracterizar o comportamento cíclico deste tipo de elementos. No total foram realizados oito ensaios em pilares, sete ensaios em nós viga-pilar interiores e seis ensaios em nós viga-pilar exteriores representativos de estruturas antigas de betão armado com armadura lisa. Os resultados experimentais permitiram avaliar a influência do escorregamento e estudar o mecanismo de corte em nós e a evolução dos danos para elementos com armadura lisa. Com base nos resultados experimentais foi proposta uma adaptação na expressão do Eurocódigo 8-3 para o cálculo da capacidade última de rotação de elementos com armadura lisa. Foi também desenvolvido um estudo paramétrico, com diferentes estratégias de modelação não linear, para a simulação da resposta de pilares considerando o escorregamento da armadura lisa. Por último, foi proposto um novo modelo simplificado trilinear para o aço que contempla o efeito do escorregamento da armadura lisa.

Micro/nanoreservoirs for controlled release of active species in smart functional coatings

This work reports one possible way to develop new functional coatings used to increase the life time of metallic structures. The functionalities selected and attributed to model coatings in the frame of this work were corrosion protection, self-sensing and prevention of fouling (antifouling). The way used to confer those functionalities to coatings was based on the encapsulation of active compounds (corrosion inhibitors, pH indicators and biocides) in micro and nanocontainers followed by their incorporation into the coating matrices. To confer active corrosion protection, one corrosion inhibitor (2-mercaptobenzothiazole, MBT) was encapsulated in two different containers, firstly in silica nanocapsules (SiNC) and in polyurea microcapsules (PU-MC). The incorporation of both containers in different models coatings shows a significant improvement in the corrosion protection of aluminum alloy 2024 (AA2024). Following the same approach, SiNC and PU-MC were also used for the encapsulation of phenolphthalein (one well known pH indicator) to introduce sensing properties in polymeric coatings. SiNC and PU-MC containing phenolphthalein acted as corrosion sensor, showing a pink coloration due to the beginning of cathodic reaction, resulting in a pH increase identified by those capsules. Their sensing performance was proved in suspension and when integrated in coatings for aluminium alloy 2024 and magnesium alloy AZ31. In a similar way, the biocide activity (antifouling) was assigned to two polymeric matrices using SiNC for encapsulation of one biocide (Dichloro-2-octyl-2H-isothiazol-3-one, DCOIT) and also SiNC-MBT was tested as biocide. The antifouling activity of those two encapsulated compounds was assessed through inhibition and consequent decrease in the bioluminescence of modified E. coli. That effect was verified in suspension and when incorporated in coatings for AISI 1008 carbon steel. The developed micro and nanocontainers presented the desired performance, allowing the introduction of new functionalities to model coatings, showing potential to be used as functional additives in the next generation of multifunctional coatings.

Propriedades intrínsecas e de processamento de termoplásticos elastoméricos incorporando borracha de pneu reciclada

O trabalho apresentado tem por objetivo contribuir para a valorização da borracha proveniente de pneus em fim de vida, assente em princípios de sustentabilidade ambiental. A abordagem adotada para a concretização deste objetivo consiste na incorporação de borracha de pneus em formulações de base termoplástica e elastomérica (TPE), adequadas ao processo de moldação por injeção. São desenvolvidos estudos sobre a morfologia, propriedades mecânicas, térmicas e reológicas das ligas poliméricas à base de granulado de borracha de pneu (GTR). A falta de adesão entre o GTR e a matriz polimérica leva à degradação das propriedades mecânicas dos materiais obtidos. A estratégia explorada passa pela utilização de um elastómero para promover o encapsulamento do GTR e, desta forma, procurar obter ligas com propriedades mecânicas características de um TPE. São analisadas ligas ternárias (TPEGTR) compostas por polipropileno (PP) de elevada fluidez, GTR e elastómero virgem. O efeito da presença de diferentes elastómeros nas ligas é analisado neste trabalho: um elastómero de etilenopropileno- dieno (EPDM), e um novo elastómero de etileno-propileno (EPR) obtido por catálise metalocénica. O estudo da morfologia das ligas obtidas mostra haver interação entre os materiais, sendo possível inferir a viabilidade da estratégia adotada para promover a adesão do GTR. A incorporação de elastómero promove o aumento da resistência ao impacto e da extensão na rotura nas ligas, o que é atribuído, fundamentalmente, ao encapsulamento do GTR e ao aumento da tenacidade da matriz termoplástica. Com o objetivo de avaliar a influência da estrutura cristalina das ligas TPEGTR no seu comportamento mecânico, procede-se à análise do processo de cristalização sob condições isotérmicas e não isotérmicas. Neste estudo, é avaliado o efeito da presença dos materiais que constituem a fase elastomérica na cinética de cristalização. Para cada uma das ligas desenvolvidas, recorre-se ao modelo de Avrami para avaliar o efeito da temperatura no mecanismo de nucleação, na morfologia das estruturas cristalinas e na taxa de cristalização. Recorre-se à reometria capilar para estudar, sob condições estacionárias, o comportamento reológico das ligas TPEGTR. O modelo de Cross-WLF é utilizado para avaliar o comportamento reológico de todos os materiais, obtendo-se resultados similares àqueles obtidos experimentalmente. O comportamento reológico dos polímeros PP, EPR e EPDM é do tipo reofluidificante, tendo o EPR um comportamento reológico similar ao do PP e o EPDM um comportamento reo-fluidificante mais pronunciado. Em todas as ligas analisadas o comportamento reológico revela-se do tipo reo-fluidificante, sendo que a presença de GTR promove o aumento da viscosidade. Os parâmetros obtidos do modelo de Cross-WLF são utilizados para realizar a simulação da etapa de injeção recorrendo a um software comercial. Os resultados obtidos são validados experimentalmente pelo processo de moldação por injeção, evidenciando uma boa adequabilidade da aplicação deste modelo a estas ligas. O trabalho desenvolvido sobre ligas TPEGTR, constitui um contributo para a valorização da borracha proveniente de pneus em fim de vida, assente em princípios de sustentabilidade ambiental.

Piezoelectricity and ferroelectricity in amino acid glycine

Bioorganic ferroelectrics and piezoelectrics are becoming increasingly important in view of their intrinsic compatibility with biological environment and biofunctionality combined with strong piezoelectric effect and switchable polarization at room temperature. Here we study piezoelectricity and ferroelectricity in the smallest amino acid glycine, representing a broad class of non-centrosymmetric amino acids. Glycine is one of the basic and important elements in biology, as it serves as a building block for proteins. Three polymorphic forms with different physical properties are possible in glycine (α, β and γ), Of special interest for various applications are non-centrosymmetric polymorphs: β-glycine and γ-glycine. The most useful β-polymorph being ferroelectric took much less attention than the other due to its instability under ambient conditions. In this work, we could grow stable microcrystals of β-glycine by the evaporation of aqueous solution on a (111)Pt/Ti/SiO2/Si substrate as a template. The effects of the solution concentration and Pt-assisted nucleation on the crystal growth and phase evolution were characterized by X-ray diffraction analysis and Raman spectroscopy. In addition, spin-coating technique was used for the fabrication of highly aligned nano-islands of β-glycine with regular orientation of the crystallographic axes relative the underlying substrate (Pt). Further we study both as-grown and tip-induced domain structures and polarization switching in the β-glycine molecular systems by Piezoresponse Force Microscopy (PFM) and compare the results with molecular modeling and computer simulations. We show that β-glycine is indeed a room-temperature ferroelectric and polarization can be switched by applying a bias to non-polar cuts via a conducting tip of atomic force microscope (AFM). Dynamics of these in-plane domains is studied as a function of applied voltage and pulse duration. The domain shape is dictated by both internal and external polarization screening mediated by defects and topographic features. Thermodynamic theory is applied to explain the domain propagation induced by the AFM tip. Our findings suggest that β-glycine is a uniaxial ferroelectric with the properties controlled by the charged domain walls which in turn can be manipulated by external bias. Besides, nonlinear optical properties of β-glycine were investigated by a second harmonic generation (SHG) method. SHG method confirmed that the 2-fold symmetry is preserved in as-grown crystals, thus reflecting the expected P21 symmetry of the β-phase. Spontaneous polarization direction is found to be parallel to the monoclinic [010] axis and directed along the crystal length. These data are confirmed by computational molecular modeling. Optical measurements revealed also relatively high values of the nonlinear optical susceptibility (50% greater than in the z-cut quartz). The potential of using stable β-glycine crystals in various applications are discussed in this work.

Gestão curricular da língua cabo-verdiana : sua integração nos curricula

Com esta investigação pretendemos analisar as perspectivas e opiniões dos professores de Portugugs, relativamente A questáo da Gestão Curricular da Língua Cabo-vediana e sua integração nos curficula. O trabalho divide-se em duas partes, sendo a primeira parte abrangendo a coniextualizaç~od o problema e objecto de estudo, e o enquadramento tebrico, com base nos suportes te6ricos de referência e a segunda parte abarca a enquadramento metodológico de um estudo prospectivo, concretizado através da realização de um inquérito por questionário aplicado a uma amostra dos professores de Português de Cabo Verde. Na primeira parte do trabalho, para além do conceito de curriculo. que foi largamente descrito a nível teórico, o estudo centra-se no conceito de gesfão cvrricular da Ccv e as suas inter-relaçáes com os conceitos de adequaçio, diferenciação e integra@ curricuiares, a luz das novas tendemias curriculares e de inovação educativa. Um outro ponto que tem merecido destaque, nesta primeira parte diz respeito aos conceitos de crioulo e pidgin e a formação do Ccv e a sua conversão em Ccv. Assim, atribuímos A política linguística ai legiiimaçào da criação de estruturas e meios indispensáveis para a afirmação e valorizaç8a da Lcv e sua integração nos curricula. A concepção da nossa investigação situa-se dentro do paradigma construtívista, conforme definido por Guba & Lincoln (19941, que permite a compreensão da realidade sob a forma de construções mentais e sociais, baseadas na interpretação e analise de conteúdo de dados obtidos junto dos sujeitos, Para a abordagem metodológica utilizada nesta pesquisa utilizou-se o inquérito por question8rio1 com recurso ao método quantitativdqualitativo, visto que se trata de um estudo descritivolinterpretativo de natureza exploratória, que se preocupa mais com o processo do que com os prdutos. A síntese dos resultados demonstra que os professores têm a noção dos conceitos de currículo e de gestão curricular, embora haja algumas divergências na conceptualização dos mesmos. No tocante à Lcv, é clara a ansiedade que os professores deixam transparecer de ver a sua Ilngua materna valorizada, no sentido da sua ascensão A língua oficial em paridade com a Lp. Assim, advoga-se a criação de estruturas e de gestão de meios materiais a humanos para a oficialiração da Lcv e sua integração nos çurricula escolares.

Structural analysis of glycans and development of microarrays from Helcobacter pylori cell surface glycome

Helicobacter pylori is a bacterial pathogen that affects more than half of the world’s population with gastro-intestinal diseases and is associated with gastric cancer. The cell surface of H. pylori is decorated with lipopolysaccharides (LPSs) composed of three distinct regions: a variable polysaccharide moiety (O-chain), a structurally conserved core oligosaccharide, and a lipid A region that anchors the LPS to the cell membrane. The O-chain of H. pylori LPS, exhibits unique oligosaccharide structures, such as Lewis (Le) antigens, similar to those present in the gastric mucosa and are involved in interactions with the host. Glucan, heptoglycan, and riban domains are present in the outer core region of some H. pylori LPSs. Amylose-like glycans and mannans are also constituents of some H. pylori strains, possibly co-expressed with LPSs. The complexity of H. pylori LPSs has hampered the establishment of accurate structure-function relationships in interactions with the host, and the design of carbohydrate-based therapeutics, such as vaccines. Carbohydrate microarrays are recent powerful and sensitive tools for studying carbohydrate antigens and, since their emergence, are providing insights into the function of carbohydrates and their involvement in pathogen-host interactions. The major goals of this thesis were the structural analysis of LPSs from H. pylori strains isolated from gastric biopsies of symptomatic Portuguese patients and the construction of a novel pathogen carbohydrate microarray of these LPSs (H. pylori LPS microarray) for interaction studies with proteins. LPSs were extracted from the cell surface of five H. pylori clinical isolates and one NCTC strain (26695) by phenol/water method, fractionated by size exclusion chromatography and analysed by gas chromatography coupled to mass spectrometry. The oligosaccharides released after mild acid treatment of the LPS were analysed by electrospray mass spectrometry. In addition to the conserved core oligosaccharide moieties, structural analyses revealed the presence of type-2 Lex and Ley antigens and N-acetyllactosamine (LacNAc) sequences, typically found in H. pylori strains. Also, the presence of O-6 linked glucose residues, particularly in LPSs from strains 2191 and NCTC 26695, pointed out to the expression of a 6-glucan. Other structural domains, namely ribans, composed of O-2 linked ribofuranose residues were observed in the LPS of most of H. pylori clinical isolates. For the LPS from strain 14382, large amounts of O-3 linked galactose units, pointing to the occurrence of a galactan, a domain recently identified in the LPS of another H. pylori strain. A particular feature to the LPSs from strains 2191 and CI-117 was the detection of large amounts of O-4 linked N-acetylglucosamine (GlcNAc) residues, suggesting the presence of chitin-like glycans, which to our knowledge have not been described for H. pylori strains. For the construction of the H. pylori LPS microarray, the structurally analysed LPSs, as well as LPS-derived oligosaccharide fractions, prepared as neoglycolipid (NGL) probes were noncovalently immobilized onto nitrocellulosecoated glass slides. These were printed together with NGLs of selected sequence defined oligosaccharides, bacterial LPSs and polysaccharides. The H. pylori LPS microarray was probed for recognition with carbohydratebinding proteins (CBPs) of known specificity. These included Le and blood group-related monoclonal antibodies (mAbs), plant lectins, a carbohydratebinding module (CBM) and the mammalian immune receptors DC-SIGN and Dectin-1. The analysis of these CBPs provided new information that complemented the structural analyses and was valuable in the quality control of the constructed microarray. Microarray analysis revealed the occurrence of type-2 Lex and Ley, but not type-1 Lea or Leb antigens, supporting the results obtained in the structural analysis. Furthermore, the H. pylori LPSs were recognised by DC-SIGN, a mammalian lectin known to interact with this bacterium through fucosylated Le epitopes expressed in its LPSs. The -fucose-specific lectin UEA-I, showed restricted binding to probes containing type-2 blood group H sequence and to the LPSs from strains CI-117 and 14382. The presence of H-type-2, as well Htype- 1 in the LPSs from these strains, was confirmed using specific mAbs. Although H-type-1 determinant has been reported for H. pylori LPSs, this is the first report of the presence of H-type-2 determinant. Microarray analysis also revealed that plant lectins known to bind 4-linked GlcNAc chitin oligosaccharide sequences bound H. pylori LPSs. STL, which exhibited restricted and strong binding to 4GlcNAc tri- and pentasaccharides, differentially recognised the LPS from the strain CI-117. The chitin sequences recognised in the LPS could be internal, as no binding was detected to this LPS with WGA, known to be specific for nonreducing terminal of 4GlcNAc sequence. Analyses of the H. pylori LPSs by SDS-PAGE and Western blot with STL provided further evidence for the presence of these novel domains in the O-chain region of this LPS. H. pylori LPS microarray was also applied to analysis of two human sera. The first was from a case infected with H. pylori (H. pylori+ CI-5) and the second was from a non-infected control.The analysis revealed a higher IgG-reactivity towards H. pylori LPSs in the H. pylori+ serum, than the control serum. A specific IgG response was observed to the LPS isolated from the CI-5 strain, which caused the infection. The present thesis has contributed to extension of current knowledge on chemical structures of LPS from H. pylori clinical isolates. Furthermore, the H. pylori LPS microarray constructed enabled the study of interactions with host proteins and showed promise as a tool in serological studies of H. pyloriinfected individuals. Thus, it is anticipated that the use of these complementary approaches may contribute to a better understanding of the molecular complexity of the LPSs and their role in pathogenesis.

Post-synthetic modification of metal–organic frameworks

Post-synthetic modification (PSM) of metal-organic frameworks encompassing the chemical transformation of the linker present is a promising new route for engineering optical centres and tuning the light emission properties of materials, both in the visible and in the near infrared (NIR) spectral regions. Here, PSM of isoreticular metal-organic framework-3 (IRMOF-3) with ethyl oxalyl monochloride, ethyl acetoacetate, pentane-2,4-dione, 3-(2- hydroxyphenyl)-3-oxopropanal, 2-chloroacetic acid, glyoxylic acid, methyl vinyl ketone and diethyl (ethoxymethylene)malonate followed by chelation of trivalent lanthanide ions afforded intriguing near infrared (Nd3+) and visible (Eu3+, Tb3+) light emitters. IRMOF-3 was used as a case in point due to both its highly porous crystalline structure and the presence of non-coordinating amino groups on the benzenedicarboxylate (bdc) linker amenable to modification. The materials were characterised by elemental analysis, powder X-ray diffraction, optical, scanning and transmission electron microscopy, Fourier transform infrared spectroscopy, and liquid and solid-state nuclear magnetic resonance. The solid-state luminescence properties of Ln-modified-IRMOF-3 were investigated at room temperature. The presence of the bdc aromatic ring, β– diketonate and oxalate enhanced the Ln3+ sensitization via ligand-to-metal energy transfer (anthena effect). As far as photocalysis is concerned, we have synthesized metal−organic frameworks (Cr-MIL-125-AC, Ag-MIL-125-AC) by a green method (solid–vapors reactions). The resulting functionalized materials show a photocatalytic activity for methylene blue degradation up to 6.52 times larger than that of the commercial photocatalyst hombikat UV-100. These findings open the door for further research for improving the photocatalytic performance of metal-organic frameworks.