Nonaqueous sol-gel routes to doped metal oxide nanoparticles: synthesis, characterization, assembly and properties

The results presented in this thesis have been achieved under the Ph.D. project entitled “Nonaqueous Sol-Gel routes to doped metal oxide nanoparticles: Synthesis, characterization, assembly and properties”. The purpose of this study is the investigation of metal oxide nanostructures doped with metals of a diverse nature, leading to different type of applications. The easier control over the reaction kinetics in solvothermal routes, compared to aqueous methods, allows to better match the reactivity between metal oxide precursors, paving the way to a facile and low temperature production of doped oxides. In this manuscript diverse examples of the exploitation of the “Benzyl Alcohol Route” are discussed. Such a powerful pathway was utilized for the synthesis of transition metal doped zirconia, hafnia and various perovskites, and the study of their magnetic properties, as well as the synthesis of rare earth doped zirconium oxide. A further extension, proving the solidity of the synthetic method, is shown for the preparation of Li4Ti5O12 nanocrystals carrying excellent electrochemical properties for lithium-ion battery applications. Finally, the effect of doping and other reaction parameters on the assembly of the nanocrystals is discussed. These studies were carried out principally at the University of Aveiro, as well as at the University of Montpellier II and at the Seoul National University due to complementary available expertises and equipments.

Measurement and modeling of hyperfine properties in ferroic materials

This thesis presents the results of perturbed angular correlation (PAC) experiments , an experimental technique which measures the hyperfine interaction at probes (radioactive ions implanted in the materials to study), from which one infers local information on an atomic scale. Furthermore, abinitio calculations using density functional theory electronic obtain results that directly complement the experiments, and are also used for theoretical research. These methods were applied in two families of materials. The manganites, with the possible existence of magnetic, charge, orbital and ferroelectric orders, are of fundamental and technological interest. The experimental results are obtained in the alkaline-earth manganites (Ca, Ba, Sr), with special interest due to the structural variety of possible polymorphs. With probes of Cd and In the stability of the probe and its location in a wide temperature range is established and a comparison with calculations allows the physical interpretation of the results. Calculations of hyperfine properties in rare-earth manganites are also presented. The second type of materials in which hyperfine properties were studied are the Manganese pnictides: MnAs, MnSb, and MnBi, compounds in which magnetism is fundamental. The experimental results obtained mainly consider the MnAs compound, whose magneto-structural transition is of great interest. The transition is analyzed in detail with the local resolution characteristic of the technique, obtaining information of the character of the transition also with complementary, more conventional techniques. The last work in this thesis uses only the first principles calculations, continuing the theme of the hyperfine interactions, but this time with respect to ferroelectrics. Several transition metal oxides with perovskite or distorted structures are considered. The electric field gradient which exists due to the quadrupole interaction in nuclei is related to the spontaneous electric polarization, the main quantity measured in ferroelectrics. This study provides a fundamental theoretical basis for previous empirical studies, suggesting new directions for research in ferroelectrics and multiferroics using techniques which measure the electric field gradient.

Chemical vapour deposition of vanadium oxide thermochromic thin films

Thermochromic materials change optical properties, such as transmittance or reflectance, with a variation in temperature. An ideal intelligent (smart) material will allow solar radiation in through a window in cold conditions, but reflect that radiation in warmer conditions. The variation in the properties is often associated with a phase change, which takes place at a definite temperature, and is normally reversible. Such materials are usually applied to window glass as thin films. This thesis presents the work on the development of thermochromic vanadium (IV) oxide (VO2) thin films – both undoped and doped with tungsten, niobium and gold nanoparticles – which could be employed as solar control coatings. The films were deposited using Chemical Vapour Deposition (CVD), using improved Atmospheric Pressure (APCVD), novel Aerosol Assisted (AACVD) and novel hybrid AP/AACVD techniques. The effects of dopants on the metalto- semiconductor transition temperature and transmittance/reflectance characteristics were also investigated. This work significantly increased the understanding of the mechanisms behind thermochromic behaviour, and resulted in thermochromic materials based on VO2 with greatly improved properties.

The Portuguese continental shelf soft-bottom benthic habitats

As comunidades de macrofauna bentónica são ecológica e economicamente relevantes, sendo fonte de diversos bens e serviços. A sua identificação, caracterização e mapeamento são importantes para identificar áreas marinhas protegidas e para uma melhor utilização do ambiente marinho. Este trabalho apresenta um estudo holístico da diversidade e distribuição espacial das comunidades de macrofauna bentónica ao longo da plataforma continental Portuguesa. Cerca de 145 locais posicionados ao longo da plataforma ocidental e setentrional foram amostrados com uma draga Smith-McIntyre de área 0,1 m2, a profundidades que variaram entre os 13 e 195 metros. Os sedimentos foram caracterizados em termos de granulometria, de matéria orgânica e geoquímica. São propostos seis habitats bentónicos principais para a plataforma continental Portuguesa, analisada a relação entre os dados biológicos e ambientais e discutidas questões biogeográficas relacionadas com a distribuição espacial de espécies e das comunidades. A distribuição da granulometria e assinatura geoquímica dos sedimentos da plataforma continental revelou-se bastante complexa, refletindo importantes diferenças nas fontes (naturais e antropogénicas), origem fluvial, geomorfologia da plataforma, hidrodinamismo e atividade biológica. Relativamente à macrofauna, entre os mais de 30 mil indivíduos recolhidos, foram identificados cerca de 737 taxa, dos quais quatro são novas espécies e aproximadamente 40 correspondem a primeiras ocorrências para a costa Portuguesa. As espécies mais frequentes foram a Ampharete finmarchica, Ampelisca sp. e Lumbrineris lusitanica sp. nov. enquanto as mais abundantes foram Mediomastus fragilis, Polygordius appendiculatus e Ampharete finmarchica. A abundância por local de amostragem variou entre 7 e 1.307 espécimens e a diversidade alfa atingiu um máximo de 96 taxa. Os sedimentos mais grosseiros apresentaram maior diversidade e abundância comparativamente com os sedimentos envasados. Foram identificados seis habitats bentónicos na plataforma continental Portuguesa: (a) sedimentos grosseiros com Protodorvillea kefersteini, Pisione remota, Angulus pygmaeus e várias espécies intersticiais; (b) areias finas hidrodinamicamente expostas e próximas da linha de costa com Magelona johnstoni, Urothoe pulchella e Angulus fabula; (c) comunidade de Abra alba em areia envasadas da plataforma profunda do noroeste; (d) Galathowenia oculata, Lumbrinerides amoureuxi e outros poliquetas escavadores e tubícolas em areais envasadas muito profundas na plataforma sudoeste; (e) Euchone rubrocincta, Nematonereis unicornis e várias espécies setentrionais nas areias envasadas da plataforma sul; (f) vasas com Sternaspis scutata, Heteromastus filiformis e Psammogammarus caecus. A granulometria do sedimento (particularmente teor em finos), matéria orgânica, profundidade e hidrodinamismo foram as variáveis ambientais com a maior relação com os padrões de distribuição da macrofauna. As espécies cosmopolitas e de latitudes superiores (clima Boreal ou Temperado Frio) dominaram o setor noroeste, sendo substituídas por espécies mais quentes na área de transição entre os canhões da Nazaré e S. Vicente, que dominaram por conseguinte a plataforma sul. O presente estudo evidenciou a abundância e diversidade da macrofauna bentónica ao longo da área costeira de Portugal, na qual coexistem faunas das províncias biogeográficas do norte da Europa, bem como subtropicais. Integrado com outro estudos, este poderá ser a base para uma melhor gestão da plataforma continental Portuguesa.

Nanocomposites for SERS : synthesis, optical and analytical studies

Esta tese descreve diversas estratégias preparativas assim como estudos de caracterização de nanocompósitos e outras nanoestruturas, para a análise em espectroscopia de Raman com intensificação por superfície (SERS). Em particular foi estudada a incorporação de nanopartículas (NPs) metálicas de Ag e Au em matrizes poliméricas visando avaliar o potencial destes materiais como novos substratos para SERS na deteção de moléculas. O primeiro capítulo consiste numa revisão bibliográfica, onde é destacado o desenvolvimento de novos substratos para SERS utilizando nomeadamente nanopartículas de Ag, Au e Cu. Numa primeira fase, esta secção apresenta uma breve descrição sobre as propriedades plasmónicas dos metais utilizados e alguns conceitos básicos de espectroscopia de difusão de Raman. Posteriormente, descreve-se em mais detalhe o efeito de SERS, revendo-se sobretudo a química de materiais descrita em trabalhos recentes tendo em conta a sua utilização como novas plataformas para análise química por SERS. O capítulo 2 descreve a síntese e caracterização de nanocompósitos de poli(acrilato de butilo) obtidos através de polimerização in situ por miniemulsão na presença de nanopartículas de Ag. Os nanocompósitos Ag/PtBA foram investigados como novos substratos de SERS visando o desenvolvimento de novas plataformas versáteis para deteção molecular. Estudos como o efeito da temperatura, pH e pressão foram investigados, visando a compreensão do efeito da matriz polimérica na difusão/adsorção do analito (ácido tiossalicílico) na superfície metálica. No capítulo 3, os nanocompósitos de Ag/PtBA descritos anteriormente foram investigados detalhadamente como substratos para bio-deteção em SERS, usando a adenina como analito modelo. Os nanocompósitos foram submetidos a vários tratamentos pré-analíticos para a bio-deteção da adenina. Foram realizadas experiências nos sistemas Ag/PtBA de modo a obter informação sobre o efeito do pH na deteção deste analito em soluções aquosas diluídas. Os nanocompósitos poliméricos obtidos apresentam a vantagem de poderem ser processados utilizando tecnologia disponível. Pelo que o estudo das suas propriedades térmicas é especialmente relevante. Assim, a influência da incorporação de NPs inorgânicas na temperatura de transição vítrea (Tg) do polímero PtBA foi investigada por meio de calorimetria diferencial de varrimento (DSC) e os resultados são apresentados no capítulo 4. Estes estudos descrevem efeitos na Tg do PtBA quando analisado em nanocompósitos obtidos por diferentes métodos (métodos ex situ e in situ), contendo nanopartículas metálicas com diferentes distribuições de tamanho e presentes em quantidade variável na matriz polimérica. Estes estudos possibilitaram relacionar a influência das NPs metálicas na mobilidade das cadeias poliméricas com as propriedades térmicas observadas. O capítulo 5 descreve a preparação e caracterização de materiais compósitos de base polimérica (PtBA) e NPs de Au com morfologia de bastonetes (NRs). Estes materiais foram investigados como substratos para SERS tendo originado um bom sinal de SERS na análise de 2-2’-ditiodipiridina. Investigouse igualmente o efeito da variação da morfologia das NPs metálicas (esferas e bastonetes), a razão de aspecto (R.A.) dos bastonetes e o tipo de matriz polimérica (PtBA e PnBA) no sinal de SERS. No capítulo 6 é descrita a utilização da técnica de SERS como método alternativo para a monitorização de alterações morfológicas de coloides de NRs de Au. Os NRs de Au foram recolhidos em diferentes fases de oxidação promovida pela presença de K2S2O8 e a sua sensibilidade como substratos de SERS foi avaliada utilizando o anião dietilditiocarbamato (DTC) como analito modelo. Os estudos foram realizados utilizando as linhas de excitação a 1064 nm e 633 nm. Este estudo demonstrou que a sensibilidade dos NRs de Au como substratos de SERS diminui à medida que a sua R.A. diminui devido à competitividade do CTAB (estabilizante) e o DTC pela superfície dos NRs. É de salientar que este processo é acompanhado por um diferente comportamento em termos de adsorção dos dois tautómeros do DTC à superfície do metal. O capítulo 7 introduz um novo tipo de compósitos para SERS, utilizando matrizes biopoliméricas. Assim, descreve-se a preparação e caracterização de nanocompósitos de carragenano e NPs de Ag. Nesta secção é avaliada a utilização destes materiais como novos substratos para a análise em SERS, utilizando a 2-2’-ditiodipiridina como molécula modelo. Descrevem-se estudos pioneiros que procuram relacionar a dependência do sinal de SERS com a força do gel. Para tal, realizou-se um estudo sistemático aos nanobiocompósitos usados como substratos de SERS em diferentes condições analíticas e investigaram-se as suas propriedades reológicas. No capitulo 8 é descrita a investigação de nanocompósitos de Ag/Gelatina como substratos para SERS, utilizando o anião dietilditiocarbamato como analito modelo. Realizaram-se várias experiências para correlacionar a variação da força do gel com o aumento do sinal de SERS bem como a diferente adsorção dos dois tautómeros do DTC à superfície do metal. Ao longo desta dissertação são apresentados metodologias distintas para a preparação e obtenção de nanocompósitos com base em polímeros (sintéticos ou naturais) e NPs metálicas (Ag e Au). Esta investigação não só permitiu a síntese e estudo de novos substratos para SERS mas também a compreensão do efeito matriz/NPs metálicas no sinal de SERS e na formação de “hot spots”. Este trabalho contribui para o enriquecimento na área da Nanociência e Nanotecnologia demonstrando a eficácia e reprodutibilidade de nanocompósitos com base em polímeros como novos substratos para SERS. Embora as propriedades óticas apresentadas por estes materiais serem aqui direcionadas para a deteção molecular pela técnica de SERS, estes materiais podem ser investigados em outras área tecnológicas.

Modeling the Western Iberian margin circulation: present and future

The purpose of this work is to carry out a comprehensive study on the Western Iberian Margin (WIM) circulation my means of numerical modeling, and to postulate what this circulation will be in the future. The adopted approach was the development of a regional ocean model configuration with high resolution, capable of reproducing the largeand small-scale dynamics of the coastal transition zone. Four numerical experiences were carried out according to these objectives: (1) a climatological run, in order to study the system’s seasonal behavior and its mean state; (2) a run forced with real winds and fluxes for period 2001-2011 in order to study the interannual variability of the system; (3) a run forced with mean fields from Global Climate Models (GCMs) for the present, in order to validate GCMs as adequate forcing for regional ocean modeling; (4) a similar run (3) for period 2071-2100, in order to assess possible consequences of a future climate scenario on the hydrography and dynamics of the WIM. Furthermore, two Lagrangian particle studies were carried out: one in order to trace the origin of the upwelled waters along the WIM; the other in order to portrait the patterns of larval dispersal, accumulation and connectivity. The numerical configuration proved to be adequate in the reproduction of the system’s mean state, seasonal characterization and an interannual variability study. There is prevalence of poleward flow at the slope, which coexists with the upwelling jet during summer, although there is evidence of its shifting offshore, and which is associated with the Mediterranean Water flow at deeper levels, suggesting a barotropic character. From the future climate scenario essay, the following conclusions were drawn: there is general warming and freshening of upper level waters; there is still poleward tendency, and despite the upwellingfavorable winds strengthening in summer the respective coastal band becomes more restricted in width and depth. In what concerns larval connectivity and dispersion along the WIM, diel vertical migration was observed to increase recruitment throughout the domain, and while smooth coastlines are better suppliers, there is higher accumulation where the topography is rougher.

Novel critical phenomena in optimization driven processes on networks

The work presented in this Ph.D thesis was developed in the context of complex network theory, from a statistical physics standpoint. We examine two distinct problems in this research field, taking a special interest in their respective critical properties. In both cases, the emergence of criticality is driven by a local optimization dynamics. Firstly, a recently introduced class of percolation problems that attracted a significant amount of attention from the scientific community, and was quickly followed up by an abundance of other works. Percolation transitions were believed to be continuous, until, recently, an 'explosive' percolation problem was reported to undergo a discontinuous transition, in [93]. The system's evolution is driven by a metropolis-like algorithm, apparently producing a discontinuous jump on the giant component's size at the percolation threshold. This finding was subsequently supported by number of other experimental studies [96, 97, 98, 99, 100, 101]. However, in [1] we have proved that the explosive percolation transition is actually continuous. The discontinuity which was observed in the evolution of the giant component's relative size is explained by the unusual smallness of the corresponding critical exponent, combined with the finiteness of the systems considered in experiments. Therefore, the size of the jump vanishes as the system's size goes to infinity. Additionally, we provide the complete theoretical description of the critical properties for a generalized version of the explosive percolation model [2], as well as a method [3] for a precise calculation of percolation's critical properties from numerical data (useful when exact results are not available). Secondly, we study a network flow optimization model, where the dynamics consists of consecutive mergings and splittings of currents flowing in the network. The current conservation constraint does not impose any particular criterion for the split of current among channels outgoing nodes, allowing us to introduce an asymmetrical rule, observed in several real systems. We solved analytically the dynamic equations describing this model in the high and low current regimes. The solutions found are compared with numerical results, for the two regimes, showing an excellent agreement. Surprisingly, in the low current regime, this model exhibits some features usually associated with continuous phase transitions.

Avaliação do perfil de cuidado de enfermagem geriátrico em hospitais de Portugal

A transição demográfica e epidemiológica da população portuguesa tem e terá um enorme impacto na utilização dos recursos de saúde. Atualmente, as pessoas idosas representam um dos grupos etários com taxas de internamento hospitalar mais significativos. Contudo, os dados sobre a hospitalização destas pessoas têm demonstrado resultados de saúde negativos, nomeadamente, o declínio funcional e cognitivo e o risco elevado de eventos adversos. Os/as enfermeiros/as têm um papel crucial na mudança desta realidade. Deste modo, a associação entre o contexto no qual decorre o cuidado de enfermagem geriátrica e os resultados deste cuidado relativos a/os utentes, enfermeiros/as e organizações têm sido proficuamente documentados. Algumas estratégias para promover a qualidade do cuidado geriátrico e a segurança das pessoas idosas hospitalizadas consistem em avaliar e (re)criar o ambiente de trabalho geriátrico dos/as enfermeiros/as (AGTE) e capacitar e treinar estes/as profissionais no cuidado à pessoa idosa. Embora, internacionalmente, os dados demonstrem a associação entre as características de hospitais e/ou enfermeiros/as e o AGTE, não existem estudos em Portugal nesta área, bem como sobre o conhecimento e as atitudes destes profissionais no contexto hospitalar. Por conseguinte, este estudo teve como objetivos: 1) traduzir, adaptar culturalmente e validar as escalas que compõem o questionário Geriatric Institucional Assessment Proflie (GIAP) para a população portuguesa; 2) analisar o AGTE (fatores intrínsecos e extrínsecos) que apoiam ou dificultam a adoção das melhores práticas geriátricas em hospitais portugueses; 3) analisar as atitudes e conhecimento de enfermeiros/as acerca de quatro síndromes geriátricas (úlceras de pressão, distúrbio do sono, contenção física e incontinência), destacando as boas práticas e os problemas encontrados nos hospitais portugueses; 4) analisar a relação entre as variáveis demográficas, profissionais e as características dos hospitais e as escalas que compõem o GIAP – versão portuguesa; 5) conhecer as perceções de enfermeiros/as acerca do cuidado às pessoas idosas hospitalizadas e dos obstáculos enfrentados para desenvolver um cuidado de boa qualidade; e 6) analisar a relação entre a perceção de enfermeiros/as sobre o AGTE e o conhecimento e atitudes geriátricas destes profissionais em função da região e unidade de internamento. Este estudo foi desenvolvido com base num método quantitativo do tipo exploratório-descritivo, transversal, prospetivo e correlacional. A amostra foi constituída por 1.068 enfermeiros/as de cinco hospitais da região norte e centro do país. A recolha de dados foi desenvolvida através de autopreenchimento do GIAP – versão portuguesa. De entre os principais resultados destacam-se: 1) a obtenção de um instrumento válido e fiável para avaliar o AGTE e conhecimentos e atitudes geriátricas; 2) a perceção de enfermeiros/as sobre o cuidado às pessoas idosas como sendo predominantemente negativa; 3) a perceção de enfermeiros/as sobre o apoio insuficiente dos líderes hospitalares para promover um AGTE favorável; 4) o cuidado a pessoas idosas com comportamentos inadequados e o uso de recursos geriátricos como os principais fatores que influenciam a eficácia e a qualidade do cuidado geriátrico; 5) a lacuna de conhecimento e atitudes negativas de enfermeiros/as acerca das quatro síndromes geriátricas; 6) a conceptualização de um modelo sobre a associação das características de enfermeiros/as, dos hospitais do estudo e das perceções destes/as profissionais sobre o cuidado geriátrico com o AGTE e o conhecimento e atitudes geriátricos; 7) a falta de apoio familiar, a descontinuidade e a escassez de tempo para o cuidado como principais obstáculos no cuidado à pessoa idosa hospitalizada; e 8) o perfil de cuidado geriátrico nos hospitais da região norte e centro de Portugal como tendencialmente homogéneo. Os resultados deste estudo sustentam a necessidade de um maior investimento dos decisores políticos, administradores hospitalares e docentes de Enfermagem na capacitação dos/as enfermeiros/as para o cuidado geriátrico e na promoção de um AGTE mais favorável. Também oferece recomendações significativas nos domínios da decisão política, da gestão institucional e da prática profissional que devem ser alvo de uma discussão alargada entre os vários agentes com responsabilidade nestes domínios. Espera-se que este estudo possa contribuir para a promoção de um contexto favorável ao desenvolvimento de um cuidado de enfermagem geriátrica de boa qualidade às pessoas hospitalizadas.

Novos materiais com polioxotungstatos substituídos com metais d e f

The present work reports studies on the new compounds obtained by the combination of polyoxoanions derived from the Keggin and Lindquist structures with several cations. The studies were first focused on the monolacunary Keggin polyoxoanions [PW11O39M(H2O)]n- (M = FeIII, MnIII and n = 4; M = CoII and n = 5) and its combination with the organic cation 1-butyl-3-methylimidazolium (Bmim+). The association of Bmim+ cation with the polyoxoanion [PW11O39Fe(H2O)]4- allowed to isolate for the first time both the monomeric and the dimeric [PW11O39Fe)2O]10- anions, with the same cation and using simple bench techniques by pH manipulation. Studies regarding the stability of these inorganic species in solution indicated that both species are present in solution in equilibrium. However, the inability to up until now isolate the dimeric unit through simple bench methods, lead to the hypothesis that the cation had a role to play in the selective precipitation of either the monomer or the dimer. Repetition of the same procedures with the polyoxoanions [SiW11O39Fe(H2O)]5- and [PW11O39M(H2O)]n- (M = FeIII, MnIII and n = 4; M = Co and n = 5), afforded only the corresponding monomeric compounds, (Bmim)5[SiW11O39FeIII(H2O)]· 4H2O (3), (Bmim)5[PW11O39CoII(H2O)]· 0.5 H2O, (4) and (Bmim)5[PW11O39MnIII(H2O)]· 0.5 H2O (5). Moreover, the combination of Bmim+ and the polyoxotungstate [PW11O39Co(H2O)]5- afforded two different crystal structures, depending on the synthetic conditions. Thus, a ratio Bmim+:POM of 5:1 and the presence of K+ cations (due to addition of KOH) led to a formula Na2K(Bmim)2[PW11.2O39Co0.8(H2O)]·7H2O (4a), whilst a ratio Bmim:POM of 7:1 led to the formation of a crystal with the chemical formula Na2(Bmim)8[PW11O39Co(H2O)]2·3H2O (4b). Electrochemical studies were performed with carbon paste electrodes modified with BmimCl to investigate the influence of the Bmim+ cation in the performance of the electrodes. The voltametric measurements obtained from solutions containing the anions [PW11O39]7- and [SiW11O39]8- are presented. Results pointed to an improvement of the acquired voltametric signal with a slight addition of BmimCl (up to 2.5% w/w), specially in the studies regarding pH variation. Additional synthesis were carried out with both the cations Omim+ and THTP+.

Promoção da acessibilidade em televisão interativa (iTV) : proposta de um serviço adaptado a utilizadores com défice visual

As infraestruturas de televisão interativa atualmente existentes possibilitam a integração de uma grande variedade de recursos e serviços, possibilitando aos utilizadores novas experiências de interação e participação. Para a maioria dos telespetadores, o uso de serviços interativos não acarreta grandes dificuldades; no entanto, para públicos com necessidades especiais, por exemplo para pessoas com défice visual, essa tarefa torna-se complexa, dificultando, ou mesmo impedindo, que estes utilizadores possam beneficiar deste tipo de serviços. Portugal não é uma exceção neste contexto, existindo um número significativo de utilizadores com défice visual (UDV) que não beneficiam totalmente das potencialidades do paradigma televisivo atual. Neste âmbito, o projeto de investigação que suporta esta tese explora a problemática do Design Universal aplicado à Televisão Interativa (iTV) e tem como objetivos a conceptualização, prototipagem e validação de um serviço de iTV adaptado especificamente a UDV, visando promover a sua inclusão digital. Para cumprir estes objetivos, a investigação dividiu-se em três etapas distintas. Na primeira etapa, a partir da Teoria Fundamentada nos Dados, foram identificadas as dificuldades e necessidades dos UDV enquanto consumidores de conteúdos televisivos e serviços de audiodescrição; foi selecionada a plataforma tecnológica mais adequada para o suporte do serviço prototipado; e foi definido um conjunto de princípios orientadores de design (POD’s) de interfaces de televisão interativa específico para este público-alvo. Inicialmente foram efetuadas duas entrevistas a 20 participantes com défice visual, para determinar as suas dificuldades e necessidades enquanto consumidores de conteúdos televisivos e serviços de audiodescrição. De seguida, foi realizada uma entrevista a um perito responsável pelo processo de transição para a TDT em Portugal (inicialmente considerou-se que a TDT seria uma plataforma promissora e poderia suportar o protótipo) e efetuada a revisão da literatura sobre POD’s para o desenvolvimento de interfaces para serviços iTV dirigidos a pessoas com défice visual. A partir dos resultados obtidos nesta etapa foi possível definir os requisitos funcionais e técnicos do sistema, bem como os seus PODs, tanto ao nível da componente gráfica, como de interação. Na segunda etapa foi concetualizado e desenvolvido o protótipo iTV adaptado a UDV ‘meo ad+’, com recurso à plataforma tecnológica IPTV da Portugal Telecom, seguindo os requisitos e os princípios de design definidos. Relativamente à terceira etapa, esta contemplou a avaliação do serviço prototipado, por parte de um grupo de participantes com défice visual. Esta fase do trabalho foi conduzida através do método de Estudo Avaliativo, possibilitando, através de testes de usabilidade e acessibilidade, complementados com entrevistas, compreender se o serviço prototipado ia efetivamente ao encontro das necessidades deste tipo de utilizadores, tendo-se observado que os participantes que estiveram envolvidos nos testes ao protótipo mostraram-se satisfeitos com as funcionalidades oferecidas pelo sistema, bem como com o design da sua interface.

Multilayered micro/nanocrystalline CVD diamond coatings for biotribology

In the present work multilayered micro/nanocrystalline (MCD/NCD) diamond coatings were developed by Hot Filament Chemical Vapour Deposition (HFCVD). The aim was to minimize the surface roughness with a top NCD layer, to maximize adhesion onto the Si3N4 ceramic substrates with a starting MCD coating and to improve the mechanical resistance by the presence of MCD/NCD interfaces in these composite coatings. This set of features assures high wear resistance and low friction coefficients which, combined to diamond biocompatibility, set this material as ideal for biotribological applications. The deposition parameters of MCD were optimized using the Taguchi method, and two varieties of NCD were used: NCD-1, grown in a methane rich gas phase, and NCD-2 where a third gas, Argon, was added to the gas mixture. The best combination of surface pre-treatments in the Si3N4 substrates is obtained by polishing the substrates with a 15 μm diamond slurry, further dry etching with CF4 plasma for 10 minutes and final ultrasonic seeding in a diamond powder suspension in ethanol for 1 hour. The interfaces of the multilayered CVD diamond films were characterized with high detail using HRTEM, STEM-EDX and EELS. The results show that at the transition from MCD to NCD a thin precursor graphitic film is formed. On the contrary, the transition of the NCD to MCD grade is free of carbon structures other than diamond, as a result of the richer atomic hydrogen content and of the higher substrate temperature for MCD deposition. At those transitions, WC nanoparticles were found due to contamination from the filament, being also present at the first interface of the MCD layer with the silicon nitride substrate. In order to study the adhesion and mechanical resistance of the diamond coatings, indentation and particle jet blasting tests were conducted, as well as tribological experiments with homologous pairs. Indentation tests proved the superior behaviour of the multilayered coatings that attained a load of 800 N without delamination, when compared to the mono and bilayered ones. The multilayered diamond coatings also reveal the best solid particle erosion resistance, due to the MCD/NCD interfaces that act as crack deflectors. These results were confirmed by an analytical model on the stress field distribution based on the von Mises criterion. Regarding the tribological testing under dry sliding, multilayered coatings also exhibit the highest critical load values (200N for Multilayers with NCD-2). Low friction coefficient values in the range μ=0.02- 0.09 and wear coefficient values in the order of ~10-7 mm3 N-1 m-1 were obtained for the ball and flat specimens indicating a mild wear regime. Under lubrication with physiological fluids (HBSS e FBS), lower wear coefficient values ~10-9-10-8 mm3 N-1 m-1) were achieved, governed by the initial surface roughness and the effective contact pressure.

Monte Carlo studies of phase transitions and adsorption : application to n-6 Lennard-Jones, C60 and zeolite systems

The solid-fluid transition properties of the n - 6 Lennard-Jones system are studied by means of extensive free energy calculations. Different values of the parameter n which regulates the steepness of the short-range repulsive interaction are investigated. Furthermore, the free energies of the n < 12 systems are calculated using the n = 12 system as a reference. The method relies on a generalization of the multiple histogram method that combines independent canonical ensemble simulations performed with different Hamiltonians and computes the free energy difference between them. The phase behavior of the fullerene C60 solid is studied by performing NPT simulations using atomistic models which treat each carbon in the molecule as a separate interaction site with additional bond charges. In particular, the transition from an orientationally frozen phase at low temperatures to one where the molecules are freely rotating at higher temperatures is studied as a function of applied pressure. The adsorption of molecular hydrogen in the zeolite NaA is investigated by means of grand-canonical Monte Carlo, in a wide range of temperatures and imposed gas pressures, and results are compared with available experimental data. A potential model is used that comprises three main interactions: van der Waals, Coulomb and induced polarization by the permanent electric field in the zeolite.

Phase transitions and nonlinear phenomena in neuronal network models

Communication and cooperation between billions of neurons underlie the power of the brain. How do complex functions of the brain arise from its cellular constituents? How do groups of neurons self-organize into patterns of activity? These are crucial questions in neuroscience. In order to answer them, it is necessary to have solid theoretical understanding of how single neurons communicate at the microscopic level, and how cooperative activity emerges. In this thesis we aim to understand how complex collective phenomena can arise in a simple model of neuronal networks. We use a model with balanced excitation and inhibition and complex network architecture, and we develop analytical and numerical methods for describing its neuronal dynamics. We study how interaction between neurons generates various collective phenomena, such as spontaneous appearance of network oscillations and seizures, and early warnings of these transitions in neuronal networks. Within our model, we show that phase transitions separate various dynamical regimes, and we investigate the corresponding bifurcations and critical phenomena. It permits us to suggest a qualitative explanation of the Berger effect, and to investigate phenomena such as avalanches, band-pass filter, and stochastic resonance. The role of modular structure in the detection of weak signals is also discussed. Moreover, we find nonlinear excitations that can describe paroxysmal spikes observed in electroencephalograms from epileptic brains. It allows us to propose a method to predict epileptic seizures. Memory and learning are key functions of the brain. There are evidences that these processes result from dynamical changes in the structure of the brain. At the microscopic level, synaptic connections are plastic and are modified according to the dynamics of neurons. Thus, we generalize our cortical model to take into account synaptic plasticity and we show that the repertoire of dynamical regimes becomes richer. In particular, we find mixed-mode oscillations and a chaotic regime in neuronal network dynamics.

Electromechanical properties of engineered lead free potassium sodium niobate based materials

K0.5Na0.5NbO3 (KNN), is the most promising lead free material for substituting lead zirconate titanate (PZT) which is still the market leader used for sensors and actuators. To make KNN a real competitor, it is necessary to understand and to improve its properties. This goal is pursued in the present work via different approaches aiming to study KNN intrinsic properties and then to identify appropriate strategies like doping and texturing for designing better KNN materials for an intended application. Hence, polycrystalline KNN ceramics (undoped, non-stoichiometric; NST and doped), high-quality KNN single crystals and textured KNN based ceramics were successfully synthesized and characterized in this work. Polycrystalline undoped, non-stoichiometric (NST) and Mn doped KNN ceramics were prepared by conventional ceramic processing. Structure, microstructure and electrical properties were measured. It was observed that the window for mono-phasic compositions was very narrow for both NST ceramics and Mn doped ceramics. For NST ceramics the variation of A/B ratio influenced the polarization (P-E) hysteresis loop and better piezoelectric and dielectric responses could be found for small stoichiometry deviations (A/B = 0.97). Regarding Mn doping, as compared to undoped KNN which showed leaky polarization (P-E) hysteresis loops, B-site Mn doped ceramics showed a well saturated, less-leaky hysteresis loop and a significant properties improvement. Impedance spectroscopy was used to assess the role of Mn and a relation between charge transport – defects and ferroelectric response in K0.5Na0.5NbO3 (KNN) and Mn doped KNN ceramics could be established. At room temperature the conduction in KNN which is associated with holes transport is suppressed by Mn doping. Hence Mn addition increases the resistivity of the ceramic, which proved to be very helpful for improving the saturation of the P-E loop. At high temperatures the conduction is dominated by the motion of ionized oxygen vacancies whose concentration increases with Mn doping. Single crystals of potassium sodium niobate (KNN) were grown by a modified high temperature flux method. A boron-modified flux was used to obtain the crystals at a relatively low temperature. XRD, EDS and ICP analysis proved the chemical and crystallographic quality of the crystals. The grown KNN crystals exhibit higher dielectric permittivity (29,100) at the tetragonal-to-cubic phase transition temperature, higher remnant polarization (19.4 μC/cm2) and piezoelectric coefficient (160 pC/N) when compared with the standard KNN ceramics. KNN single crystals domain structure was characterized for the first time by piezoforce response microscopy. It could be observed that <001> - oriented potassium sodium niobate (KNN) single crystals reveal a long range ordered domain pattern of parallel 180° domains with zig-zag 90° domains. From the comparison of KNN Single crystals to ceramics, It is argued that the presence in KNN single crystal (and absence in KNN ceramics) of such a long range order specific domain pattern that is its fingerprint accounts for the improved properties of single crystals. These results have broad implications for the expanded use of KNN materials, by establishing a relation between the domain patterns and the dielectric and ferroelectric response of single crystals and ceramics and by indicating ways of achieving maximised properties in KNN materials. Polarized Raman analysis of ferroelectric potassium sodium niobate (K0.5Na0.5)NbO3 (KNN) single crystals was performed. For the first time, an evidence is provided that supports the assignment of KNN single crystals structure to the monoclinic symmetry at room temperature. Intensities of A′, A″ and mixed A′+A″ phonons have been theoretically calculated and compared with the experimental data in dependence of crystal rotation, which allowed the precise determination of the Raman tensor coefficients for (non-leaking) modes in monoclinic KNN. In relation to the previous literature, this study clarifies that assigning monoclinic phase is more suitable than the orthorhombic one. In addition, this study is the basis for non-destructive assessments of domain distribution by Raman spectroscopy in KNN-based lead-free ferroelectrics with complex structures. Searching a deeper understanding of the electrical behaviour of both KNN single crystal and polycrystalline materials for the sake of designing optimized KNN materials, a comparative study at the level of charge transport and point defects was carried out by impedance spectroscopy. KNN single crystals showed lower conductivity than polycrystals from room temperature up to 200 ºC, but above this temperature polycrystalline KNN displays lower conductivity. The low temperature (T < 200 ºC) behaviour reflects the different processing conditions of both ceramics and single crystals, which account for less defects prone to charge transport in the case of single crystals. As temperature increases (T > 200 ºC) single crystals become more conductive than polycrystalline samples, in which grain boundaries act as barriers to charge transport. For even higher temperatures the conductivity difference between both is increased due to the contribution of ionic conduction in single crystals. Indeed the values of activation energy calculated to the high temperature range (T > 300 ºC) were 1.60 and 0.97 eV, confirming the charge transport due to ionic conduction and ionized oxygen vacancies in single crystals and polycrystalline KNN, respectively. It is suggested that single crystals with low defects content and improved electromechanical properties could be a better choice for room temperature applications, though at high temperatures less conductive ceramics may be the choice, depending on the targeted use. Aiming at engineering the properties of KNN polycrystals towards the performance of single crystals, the preparation and properties study of (001) – oriented (K0.5Na0.5)0.98Li0.02NbO3 (KNNL) ceramics obtained by templated grain growth (TGG) using KNN single crystals as templates was undertaken. The choice of KNN single crystals templates is related with their better properties and to their unique domain structure which were envisaged as a tool for templating better properties in KNN ceramics too. X-ray diffraction analysis revealed for the templated ceramics a monoclinic structure at room temperature and a Lotgering factor (f) of 40% which confirmed texture development. These textured ceramics exhibit a long range ordered domain pattern consisting of 90º and 180º domains, similar to the one observed in the single crystals. Enhanced dielectric (13017 at TC), ferroelectric (2Pr = 42.8 μC/cm2) and piezoelectric (d33 = 280 pC/N) properties are observed for textured KNNL ceramics as compared to the randomly oriented ones. This behaviour is suggested to be due to the long range ordered domain patterns observed in the textured ceramics. The obtained results as compared with the data previously reported on texture KNN based ceramics confirm that superior properties were found due to ordered repeated domain pattern. This study provides an useful approach towards properties improvement of KNN-based piezoelectric ceramics. Overall, the present results bring a significant contribution to the pool of knowledge on the properties of sodium potassium niobate materials: a relation between the domain patterns and di-, ferro-, and piezo-electric response of single crystals and ceramics was demonstrated and ways of engineering maximised properties in KNN materials, for example by texturing were established. This contribution is envisaged to have broad implications for the expanded use of KNN over the alternative lead-based materials.

Ecological quality assessment in transitional systems

Estuaries are poles of attraction for human settlement which is a source of pressures to surface water bodies. The implementation of the European Water Framework Directive (WDF, 2000/60/EC) has increased the investigation in order to develop methodologies to assess the Ecological Quality Status (EQS) of aquatic ecosystems. Transitional systems are naturally stressed and characterized by highly dynamic physical, chemical and hydro-morphologic conditions and by species with a higher level of tolerance to change, being more difficult to develop suitable quality indicators for these systems. The general purpose of this study is to test the ability of synthesis descriptors, including primary (S, taxa richness) and derived biological variable (H’, Shannon-Wiener diversity), biotic indices (AMBI and M-AMBI), body size properties (abundance distribution by body size classes, length, weight and length-weight relationships) and non-taxonomic indices (ISS), as well as functional indicators related to the decomposition rates of various experimental substrates, a macrophyte (Phragmites australis) and an alga (Fucus vesiculosus), to evaluate the environmental quality in transitional systems. This study was carried out in one of the most pristine channels of the Ria the Aveiro, Mira Channel, along a full salinity gradient and in a metals and metalloid sediment contamination area, the Estarreja Channel, and two reference channels (Canelas and Salreu). In this study were used different sampling techniques, the leaf-bag technique and a hand-held corer. In Mira Channel, the alga and the macrophyte presented an opposite trend in the decomposition rate along the salinity gradient, with the decomposition rates of the alga always higher than those of the macrophyte. The decomposition rates of the macrophyte and the alga were higher in the mid estuary and in higher salinity areas, respectively, corresponding to the preferencial distribution areas of each species. The macrobenthic fauna associated with the decaying and an artificial substrate (control) showed equally well the benthic succession from the marine to the freshwater areas and, despite the strong differences in the decay rates, no significant differences were found between the benthic communities associated with the alga and the macrophyte. The body size properties of the macrobenthic fauna associated with the P. australis leaf-bag (1mm and 5mm) and corer samples were studied along the full salinity gradient. The dominant species of the sub-set of measured specimens were not the same of the original macrobenthic fauna sampled but, despite that, the sub-set of measured specimens was also able to show the benthic succession from the marine to the freshwater areas. The body size abundance distribution of the benthic macroinvertebrates according to the ISS size classes did not show a particular trend in any sampler along the salinity gradient. Significant differences were found in the length, weight and length-weight relationships of Annelids, , Molluscs and even some species along the salinity gradient. No significant differences were found in the AMBI, M-AMBI and ISS values along the salinity gradient for all the samplers. The EQS of the corer samples obtained using the M-AMBI was lower than that of the leaf-bags. The EQS obtained with the ISS was higher than that obtained with the M-AMBI in the leaf-bags but not in the corer samples. The ecological effects of contaminated sediments associated with the industrial chemical effluents discharged in the Estarreja Channel were studied a decade after ceasing the emissions, using the Sediment Quality Triad approach and two reference channels. The results showed that despite the emissions ceased in 2004, the sediment remains polluted with high levels of metals and metalloid, available to bioaccumulation and with severe consequences at the community level. The sediment contamination problem was also studied using the leaf-bag technique with a macrophyte, an alga and a control substrate. The results showed that the decay rates, the associated macrofauna and the application of the AMBI, M-AMBI and ISS indices to the mesh-bag samples were not able to identify the sediment contamination. Contrarily to the AMBI, the M-AMBI and the ISS showed significant differences between the contaminated and the reference channels for the corer samples. Although such statistical significance, the interest of using these complex biotic indices could be questioned, when much simple ones, like the S and H’ allow to reach the same conclusions.