Aplicação de cortiça em dois tipos de reatores para tratamento de água

A qualidade da água degradou-se de forma relevante nas últimas décadas e os processos de sorção têm vindo a ser investigados como métodos promissores para o tratamento de águas contaminadas. Neste trabalho avaliou-se a capacidade de dois tipos de cortiça para a remoção de diversos contaminantes, em reatores de vaso fechado e de leito fixo. Os ensaios realizados em reatores de vaso fechado permitiram (i) avaliar o efeito do pH e da granulometria na eficiência dos sorventes na remoção de mercúrio e (ii) avaliar a afinidade dos sorventes para outros contaminantes, nomeadamente arsénio, cádmio, níquel e chumbo. Estruturalmente as duas cortiças estudadas aparentam ser semelhantes, com uma pequena diferença de comportamento ácido-base e não apresentam diferenças estatisticamente significativas na remoção de mercúrio. Os resultados obtidos permitiram constatar que o processo de remoção é independente do pH, tendo-se obtido percentagens de remoção da ordem dos 80% e de concentrações de mercúrio na cortiça na ordem dos 117 μg/g. As cortiças estudadas revelaram-se menos eficazes no tratamento de água com os restantes contaminantes, atingindo percentagens de remoção máximas de 0% para As, 11% para Cd, 35% para Ni e 69% para Pb. Os ensaios em leito fixo, mesmo sem terem sido otimizados, revelam que é possível obter uma eficácia de remoção de mercúrio superior a 90% nas primeiras 40 horas de trabalho, sendo a concentração de mercúrio no leito de 680 μg/g. Relativamente aos mecanismos de sorção, os resultados experimentais indicam que estes são possivelmente de natureza química e que as interações eletrostáticas têm pouca importância.

Inter layer and cooperative design strategies for green mobile networks

The promise of a truly mobile experience is to have the freedom to roam around anywhere and not be bound to a single location. However, the energy required to keep mobile devices connected to the network over extended periods of time quickly dissipates. In fact, energy is a critical resource in the design of wireless networks since wireless devices are usually powered by batteries. Furthermore, multi-standard mobile devices are allowing users to enjoy higher data rates with ubiquitous connectivity. However, the bene ts gained from multiple interfaces come at a cost in terms of energy consumption having profound e ect on the mobile battery lifetime and standby time. This concern is rea rmed by the fact that battery lifetime is one of the top reasons why consumers are deterred from using advanced multimedia services on their mobile on a frequent basis. In order to secure market penetration for next generation services energy e ciency needs to be placed at the forefront of system design. However, despite recent e orts, energy compliant features in legacy technologies are still in its infancy, and new disruptive architectures coupled with interdisciplinary design approaches are required in order to not only promote the energy gain within a single protocol layer, but to enhance the energy gain from a holistic perspective. A promising approach is cooperative smart systems, that in addition to exploiting context information, are entities that are able to form a coalition and cooperate in order to achieve a common goal. Migrating from this baseline, this thesis investigates how these technology paradigm can be applied towards reducing the energy consumption in mobile networks. In addition, we introduce an additional energy saving dimension by adopting an interlayer design so that protocol layers are designed to work in synergy with the host system, rather than independently, for harnessing energy. In this work, we exploit context information, cooperation and inter-layer design for developing new energy e cient and technology agnostic building blocks for mobile networks. These technology enablers include energy e cient node discovery and short-range cooperation for energy saving in mobile handsets, complemented by energy-aware smart scheduling for promoting energy saving on the network side. Analytical and simulations results were obtained, and veri ed in the lab on a real hardware testbed. Results have shown that up to 50% energy saving could be obtained.

Metais em águas e sedimentos da plataforma dos Açores

A presente tese tem por objetivo principal contribuir para o conhecimento da geoquímica sedimentar da zona oceânica da crista da Terceira e montanhas submarinas a sul (região entre 29-39ºN e 27-32ºW), integrando também a caraterização dos metais e nutrientes na coluna de água e propondo concentrações para servirem de referência nesta região do Atlântico Central. Para o efeito foram realizadas amostragens na coluna de água em sete locais e de sedimento em cinco locais, durante a campanha oceanográfica designada por EMEPC/AÇORES/G3/2007 a bordo do navio SV Kommandor Jack, no âmbito do projeto da Estrutura de Missão para a Extensão da Plataforma Continental (EMEPC). Os perfis de CTD da coluna de água na região estudada revelam a presença de massas de água distintas: a Western North Atlantic Central Water (WNACW), a Eastern North Atlantic Central Water tropical (ENACWt), a Eastern North Atlantic Central Water polar (ENACWp), a Mediterranean Overflow Water (MOW), a Deep Mediterranean Water (DMW) e a North Eastern Atlantic Deep Water (NEADW). Observou-se nos perfis de temperatura e salinidade, referentes aos primeiros 200 m da coluna de água, um gradiente meridional negativo entre as estações localizadas na crista da Terceira e as estações localizadas mais a sul. Observou-se nas águas superficiais valores de oxigénio dissolvido de 93% e de pH de 8,1, assim como que as concentrações dos nutrientes NOx, PO4 e SiO2 variam de acordo com a atividade biológica, tendo-se registado concentrações medianas mais baixas, respetivamente de 6,5, 0,23 e 1,3 mol L-1, que aumentam com a profundidade devido à ausência de produção primária (respetivamente 31, 1,4 e 22 mol L-1). As concentrações de NH4 e de SO4 não variam significativamente nas massas de água, sendo os valores medianos mínimos e máximos de 0,69 a 0,79 mol L-1 para o NH4 e de 30 a 32 mol L-1 para o SO4. São propostas concentrações de referência para as massas de água, para os elementos cobre, cádmio, chumbo e arsénio. Os perfis de sedimento analisados permitem distinguir os sedimentos na crista da Terceira (core A) dos restantes (cores B a E). A grande variabilidade textural encontrada no core A, que contrasta com os outros cores analisados, deve-se a importantes contribuições terrígenas, originadas pela erosão sub-aérea e pela atividade vulcânica das ilhas próximas. iv resumo (continuação) A análise mineralógica, efetuada à fração areia e à fração fina (< 63 μm), confirma que os sedimentos do core A derivam de rochas vulcânicas formadas maioritariamente por piroxenas, olivinas, anfíbolas, biotite, alterites e ainda calcite, plagióclase e magnetite, tendo-se identificado ao microscópio a glauconite e o vidro vulcânico. De acordo com a composição química destes minerais o core A apresenta valores mais elevados de Al, Fe, K, P, Mg, Si, Na, Zn, V, Cr e Mn relativamente aos cores B a E. Os cores B a E apresentam grandes quantidades de calcite (>80%) formada maioritariamente por foraminíferos e nanoplâncton calcário (cocolitóforos). A fração areia confirma a composição maioritariamente carbonatada com grande abundância de material biogénico formado por oozes de foraminíferos (planctónicos e bentónicos) com raras espículas de espongiários e restos de conchas. Os cores B a E apresentam valores muito mais elevados que o core A para os elementos Ca e Sr. Os resultados para o Al, Fe, K, P, Si, Na, As, Cu, Ni, Zn, V, Cr, Li, Pb, Cd e Co presentes nos locais B, C, D e E sugerem que estes cores são comparáveis aos sedimentos de fundo carbonatados. Propõe-se concentrações de referência para a região do Atlântico compreendida entre 29-39ºN e 27-32ºW considerando a primeira camada colhida em cada core. Para o core A as concentrações são normalizadas a 5% de Al e CaCO3, enquanto que para os cores B a E são normalizadas a 2% de Al e CaCO3. Assim as concentrações de referência para o core A são: As – 18 mg kg-1, Cr – 91 mg kg-1, Cu – 127 mg kg-1, Ni – 84 mg kg-1, Pb – 41 mg kg-1, Hg – 41 ng g-1 e Zn – 482 mg kg-1. Para os cores B a E as concentrações de referência são: As – 3 mg kg-1, Cr – 10 mg kg-1, Cu – 36 mg kg-1 Ni – 12 mg kg -1, Hg – 3 ng g-1 e Zn – 20 mg kg-1. Para os restantes metais as concentrações de referência para o core A são: Al – 9%, Si – 25%, Fe – 6%, Ca – 13%, K – 2%, Mg – 2%, Na – 3%, P – 0,4%, Sr – 900 mg kg-1, Li – 10 mg kg-1, Mn – 1200 mg kg-1, Ba – 700 mg kg-1 e V – 140 mg kg-1. Para os cores B a E as concentrações de referência são: Al – 0,9%, Si – 2%, Fe – 0,2%, Ca – 95%, K – 0,3%, Mg – 0,4%, Na – 0,3%, P – 0,04%, Sr – 2600 mg kg-1, Li – 5 mg kg-1, Mn – 240 mg kg-1, Ba – 345 mg kg-1, Co – 2 mg kg-1 e V – 6 mg kg-1. Os resultados da presente tese constituem um contributo para a caraterização geoquímica da região e podem servir de referência à monitorização futura do mar dos Açores e montes submarinos a sul.

The impact of communication disability on quality of life of people with aphasia and their caregivers

Aphasia is a chronic acquired communication disorder that may change people with aphasia (PWA) and their caregivers’ lives for ever. Social and emotional changes are frequently reported by both, although the impact of these changes in quality of life (QOL) needs further research. This study identifies predictors and variables that influence PWA’s and their caregivers’ QOL and social relationships (SR). A cross-sectional descriptive, correlational and comparative study was undertaken with 255 individuals from Portuguese general population (mean age 43 years, range 25-84 years; 148 females, 107 males), 25 PWA (mean age 54 years, range 20-71; 12 females and 13 males), and 25 caregivers (mean age 51 years, range 26-73; 17 females and 8 males). All the participants completed the World Health Quality of Life Bref instrument, the SR domain of the World Health Organization Quality of Life – 100 scale, and the Center for Epidemiologic Studies Depression Scale. Participants with aphasia completed the Lisbon Aphasia Assessment Battery, Barthel Index, Frenchay Activities Index, Communication Disability Profile and the Modified Mini-Mental State which evaluated language disability, aphasia coefficient, activities, participation and cognition. In addition, caregivers completed the Carers’ Assessment of Managing Index to assess coping strategies. PWA and their caregivers are less satisfied with their QOL and SR than Portuguese general population; whereas PWA have the worse QOL and SR. Thus, aphasia seems to impact negatively in their QOL and SR. Emotional status has great importance for QOL and SR among the three groups. PWA’s activities and participation have great impact in both PWA’s and caregivers’ QOL and SR. Additionally, emotional status and participation are the best predictors of PWA’s QOL. Along with these two variables, activities of the PWA are the best predictors of caregivers’ QOL. Participation is the best predictor of PWA’s SR; emotional status and number of cohabitants are best predictors for caregivers’ SR. Aphasia assessment and intervention should take into account all the factors that influence PWA’s and caregivers’ QOL and SR so the central goal of enhancing it can be achieved. These results are important for identifying and planning support needs and are useful in the orientation of the activities carried out by the service providers allowing the adjustment of health programs and policies based on people’s real life needs.

Reliable and energy efficient routing for ad hoc networks

In Mobile Ad hoc NETworks (MANETs), where cooperative behaviour is mandatory, there is a high probability for some nodes to become overloaded with packet forwarding operations in order to support neighbor data exchange. This altruistic behaviour leads to an unbalanced load in the network in terms of traffic and energy consumption. In such scenarios, mobile nodes can benefit from the use of energy efficient and traffic fitting routing protocol that better suits the limited battery capacity and throughput limitation of the network. This PhD work focuses on proposing energy efficient and load balanced routing protocols for ad hoc networks. Where most of the existing routing protocols simply consider the path length metric when choosing the best route between a source and a destination node, in our proposed mechanism, nodes are able to find several routes for each pair of source and destination nodes and select the best route according to energy and traffic parameters, effectively extending the lifespan of the network. Our results show that by applying this novel mechanism, current flat ad hoc routing protocols can achieve higher energy efficiency and load balancing. Also, due to the broadcast nature of the wireless channels in ad hoc networks, other technique such as Network Coding (NC) looks promising for energy efficiency. NC can reduce the number of transmissions, number of re-transmissions, and increase the data transfer rate that directly translates to energy efficiency. However, due to the need to access foreign nodes for coding and forwarding packets, NC needs a mitigation technique against unauthorized accesses and packet corruption. Therefore, we proposed different mechanisms for handling these security attacks by, in particular by serially concatenating codes to support reliability in ad hoc network. As a solution to this problem, we explored a new security framework that proposes an additional degree of protection against eavesdropping attackers based on using concatenated encoding. Therefore, malicious intermediate nodes will find it computationally intractable to decode the transitive packets. We also adopted another code that uses Luby Transform (LT) as a pre-coding code for NC. Primarily being designed for security applications, this code enables the sink nodes to recover corrupted packets even in the presence of byzantine attacks.

Metais em plantas e algas : acumulação e potencial aplicação em processos de remediação

The present work reports the study of the bioaccumulation of potentially toxic elements (cadmium, lead and mercury) by marine macroalgae (Ulva lactuca, Fucus vesiculosus and Gracilaria gracilis), abundant in the coast and estuarine systems worldwide. These organisms proved to be capable of withstanding moderate multi-metallic contamination (environmentally relevant concentrations), incorporating high amounts of metal in their tissues. The high removal percentages achieved, in particular for mercury (99%), demonstrate the potential of these algae as a basis for a new biotechnological treatment of saline waters contaminated with metals (more efficient, cost-effective and environmentally friendly than conventional methods). U. lactuca was considered the most promising due to the better performance presented. The comparison between the bioaccumulation and biosorption processes suggested that in some cases the use of the living organism will have advantages over the application of biomass, due to the simplicity of the overall process, and the lower residual concentration of metal achieved in the solution (especially for Cd). The transfer and accumulation of Hg by terrestrial plants (Brassica juncea and Lolium perenne) in agricultural fields near a contaminated industrial area was also studied. Despite the low bioaccumulation factors found (<1), there were high Hg content in plants (up to 84 mg kg-1 in roots and up 6.9 mg kg-1 in shoots, dry weight). Daily intake estimates for grazing animals (cows and sheep) pointed to the potential risk to human health derived from consumption of their meat. The results highlighted the important role that plants and algae may have in protection, risk assessment and remediation of environmental systems contaminated with metals.

Ferroelectric : CNTs structures fabrication for advanced functional nano devices

This work is about the combination of functional ferroelectric oxides with Multiwall Carbon Nanotubes for microelectronic applications, as for example potential 3 Dimensional (3D) Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Miniaturized electronics are ubiquitous now. The drive to downsize electronics has been spurred by needs of more performance into smaller packages at lower costs. But the trend of electronics miniaturization challenges board assembly materials, processes, and reliability. Semiconductor device and integrated circuit technology, coupled with its associated electronic packaging, forms the backbone of high-performance miniaturized electronic systems. However, as size decreases and functionalization increases in the modern electronics further size reduction is getting difficult; below a size limit the signal reliability and device performance deteriorate. Hence miniaturization of siliconbased electronics has limitations. On this background the Road Map for Semiconductor Industry (ITRS) suggests since 2011 alternative technologies, designated as More than Moore; being one of them based on carbon (carbon nanotubes (CNTs) and graphene) [1]. CNTs with their unique performance and three dimensionality at the nano-scale have been regarded as promising elements for miniaturized electronics [2]. CNTs are tubular in geometry and possess a unique set of properties, including ballistic electron transportation and a huge current caring capacity, which make them of great interest for future microelectronics [2]. Indeed CNTs might have a key role in the miniaturization of Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Moving from a traditional two dimensional (2D) design (as is the case of thin films) to a 3D structure (based on a tridimensional arrangement of unidimensional structures) will result in the high reliability and sensing of the signals due to the large contribution from the bottom electrode. One way to achieve this 3D design is by using CNTs. Ferroelectrics (FE) are spontaneously polarized and can have high dielectric constants and interesting pyroelectric, piezoelectric, and electrooptic properties, being a key application of FE electronic memories. However, combining CNTs with FE functional oxides is challenging. It starts with materials compatibility, since crystallization temperature of FE and oxidation temperature of CNTs may overlap. In this case low temperature processing of FE is fundamental. Within this context in this work a systematic study on the fabrication of CNTs - FE structures using low cost low temperature methods was carried out. The FE under study are comprised of lead zirconate titanate (Pb1-xZrxTiO3, PZT), barium titanate (BaTiO3, BT) and bismuth ferrite (BiFeO3, BFO). The various aspects related to the fabrication, such as effect on thermal stability of MWCNTs, FE phase formation in presence of MWCNTs and interfaces between the CNTs/FE are addressed in this work. The ferroelectric response locally measured by Piezoresponse Force Microscopy (PFM) clearly evidenced that even at low processing temperatures FE on CNTs retain its ferroelectric nature. The work started by verifying the thermal decomposition behavior under different conditions of the multiwall CNTs (MWCNTs) used in this work. It was verified that purified MWCNTs are stable up to 420 ºC in air, as no weight loss occurs under non isothermal conditions, but morphology changes were observed for isothermal conditions at 400 ºC by Raman spectroscopy and Transmission Electron Microscopy (TEM). In oxygen-rich atmosphere MWCNTs started to oxidized at 200 ºC. However in argon-rich one and under a high heating rate MWCNTs remain stable up to 1300 ºC with a minimum sublimation. The activation energy for the decomposition of MWCNTs in air was calculated to lie between 80 and 108 kJ/mol. These results are relevant for the fabrication of MWCNTs – FE structures. Indeed we demonstrate that PZT can be deposited by sol gel at low temperatures on MWCNTs. And particularly interesting we prove that MWCNTs decrease the temperature and time for formation of PZT by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs - PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNTs - PZT synthesised at 500 ºC for 1 h was proved by PFM. In the continuation of this work we developed a low cost methodology of coating MWCNTs using a hybrid sol-gel / hydrothermal method. In this case the FE used as a proof of concept was BT. BT is a well-known lead free perovskite used in many microelectronic applications. However, synthesis by solid state reaction is typically performed around 1100 to 1300 ºC what jeopardizes the combination with MWCNTs. We also illustrate the ineffectiveness of conventional hydrothermal synthesis in this process due the formation of carbonates, namely BaCO3. The grown MWCNTs - BT structures are ferroelectric and exhibit an electromechanical response (15 pm/V). These results have broad implications since this strategy can also be extended to other compounds of materials with high crystallization temperatures. In addition the coverage of MWCNTs with FE can be optimized, in this case with non covalent functionalization of the tubes, namely with sodium dodecyl sulfate (SDS). MWCNTs were used as templates to grow, in this case single phase multiferroic BFO nanorods. This work shows that the use of nitric solvent results in severe damages of the MWCNTs layers that results in the early oxidation of the tubes during the annealing treatment. It was also observed that the use of nitric solvent results in the partial filling of MWCNTs with BFO due to the low surface tension (<119 mN/m) of the nitric solution. The opening of the caps and filling of the tubes occurs simultaneously during the refluxing step. Furthermore we verified that MWCNTs have a critical role in the fabrication of monophasic BFO; i.e. the oxidation of CNTs during the annealing process causes an oxygen deficient atmosphere that restrains the formation of Bi2O3 and monophasic BFO can be obtained. The morphology of the obtained BFO nano structures indicates that MWCNTs act as template to grow 1D structure of BFO. Magnetic measurements on these BFO nanostructures revealed a week ferromagnetic hysteresis loop with a coercive field of 956 Oe at 5 K. We also exploited the possible use of vertically-aligned multiwall carbon nanotubes (VA-MWCNTs) as bottom electrodes for microelectronics, for example for memory applications. As a proof of concept BiFeO3 (BFO) films were in-situ deposited on the surface of VA-MWCNTs by RF (Radio Frequency) magnetron sputtering. For in situ deposition temperature of 400 ºC and deposition time up to 2 h, BFO films cover the VA-MWCNTs and no damage occurs either in the film or MWCNTs. In spite of the macroscopic lossy polarization behaviour, the ferroelectric nature, domain structure and switching of these conformal BFO films was verified by PFM. A week ferromagnetic ordering loop was proved for BFO films on VA-MWCNTs having a coercive field of 700 Oe. Our systematic work is a significant step forward in the development of 3D memory cells; it clearly demonstrates that CNTs can be combined with FE oxides and can be used, for example, as the next 3D generation of FERAMs, not excluding however other different applications in microelectronics.

Electromechanical properties of engineered lead free potassium sodium niobate based materials

K0.5Na0.5NbO3 (KNN), is the most promising lead free material for substituting lead zirconate titanate (PZT) which is still the market leader used for sensors and actuators. To make KNN a real competitor, it is necessary to understand and to improve its properties. This goal is pursued in the present work via different approaches aiming to study KNN intrinsic properties and then to identify appropriate strategies like doping and texturing for designing better KNN materials for an intended application. Hence, polycrystalline KNN ceramics (undoped, non-stoichiometric; NST and doped), high-quality KNN single crystals and textured KNN based ceramics were successfully synthesized and characterized in this work. Polycrystalline undoped, non-stoichiometric (NST) and Mn doped KNN ceramics were prepared by conventional ceramic processing. Structure, microstructure and electrical properties were measured. It was observed that the window for mono-phasic compositions was very narrow for both NST ceramics and Mn doped ceramics. For NST ceramics the variation of A/B ratio influenced the polarization (P-E) hysteresis loop and better piezoelectric and dielectric responses could be found for small stoichiometry deviations (A/B = 0.97). Regarding Mn doping, as compared to undoped KNN which showed leaky polarization (P-E) hysteresis loops, B-site Mn doped ceramics showed a well saturated, less-leaky hysteresis loop and a significant properties improvement. Impedance spectroscopy was used to assess the role of Mn and a relation between charge transport – defects and ferroelectric response in K0.5Na0.5NbO3 (KNN) and Mn doped KNN ceramics could be established. At room temperature the conduction in KNN which is associated with holes transport is suppressed by Mn doping. Hence Mn addition increases the resistivity of the ceramic, which proved to be very helpful for improving the saturation of the P-E loop. At high temperatures the conduction is dominated by the motion of ionized oxygen vacancies whose concentration increases with Mn doping. Single crystals of potassium sodium niobate (KNN) were grown by a modified high temperature flux method. A boron-modified flux was used to obtain the crystals at a relatively low temperature. XRD, EDS and ICP analysis proved the chemical and crystallographic quality of the crystals. The grown KNN crystals exhibit higher dielectric permittivity (29,100) at the tetragonal-to-cubic phase transition temperature, higher remnant polarization (19.4 μC/cm2) and piezoelectric coefficient (160 pC/N) when compared with the standard KNN ceramics. KNN single crystals domain structure was characterized for the first time by piezoforce response microscopy. It could be observed that <001> - oriented potassium sodium niobate (KNN) single crystals reveal a long range ordered domain pattern of parallel 180° domains with zig-zag 90° domains. From the comparison of KNN Single crystals to ceramics, It is argued that the presence in KNN single crystal (and absence in KNN ceramics) of such a long range order specific domain pattern that is its fingerprint accounts for the improved properties of single crystals. These results have broad implications for the expanded use of KNN materials, by establishing a relation between the domain patterns and the dielectric and ferroelectric response of single crystals and ceramics and by indicating ways of achieving maximised properties in KNN materials. Polarized Raman analysis of ferroelectric potassium sodium niobate (K0.5Na0.5)NbO3 (KNN) single crystals was performed. For the first time, an evidence is provided that supports the assignment of KNN single crystals structure to the monoclinic symmetry at room temperature. Intensities of A′, A″ and mixed A′+A″ phonons have been theoretically calculated and compared with the experimental data in dependence of crystal rotation, which allowed the precise determination of the Raman tensor coefficients for (non-leaking) modes in monoclinic KNN. In relation to the previous literature, this study clarifies that assigning monoclinic phase is more suitable than the orthorhombic one. In addition, this study is the basis for non-destructive assessments of domain distribution by Raman spectroscopy in KNN-based lead-free ferroelectrics with complex structures. Searching a deeper understanding of the electrical behaviour of both KNN single crystal and polycrystalline materials for the sake of designing optimized KNN materials, a comparative study at the level of charge transport and point defects was carried out by impedance spectroscopy. KNN single crystals showed lower conductivity than polycrystals from room temperature up to 200 ºC, but above this temperature polycrystalline KNN displays lower conductivity. The low temperature (T < 200 ºC) behaviour reflects the different processing conditions of both ceramics and single crystals, which account for less defects prone to charge transport in the case of single crystals. As temperature increases (T > 200 ºC) single crystals become more conductive than polycrystalline samples, in which grain boundaries act as barriers to charge transport. For even higher temperatures the conductivity difference between both is increased due to the contribution of ionic conduction in single crystals. Indeed the values of activation energy calculated to the high temperature range (T > 300 ºC) were 1.60 and 0.97 eV, confirming the charge transport due to ionic conduction and ionized oxygen vacancies in single crystals and polycrystalline KNN, respectively. It is suggested that single crystals with low defects content and improved electromechanical properties could be a better choice for room temperature applications, though at high temperatures less conductive ceramics may be the choice, depending on the targeted use. Aiming at engineering the properties of KNN polycrystals towards the performance of single crystals, the preparation and properties study of (001) – oriented (K0.5Na0.5)0.98Li0.02NbO3 (KNNL) ceramics obtained by templated grain growth (TGG) using KNN single crystals as templates was undertaken. The choice of KNN single crystals templates is related with their better properties and to their unique domain structure which were envisaged as a tool for templating better properties in KNN ceramics too. X-ray diffraction analysis revealed for the templated ceramics a monoclinic structure at room temperature and a Lotgering factor (f) of 40% which confirmed texture development. These textured ceramics exhibit a long range ordered domain pattern consisting of 90º and 180º domains, similar to the one observed in the single crystals. Enhanced dielectric (13017 at TC), ferroelectric (2Pr = 42.8 μC/cm2) and piezoelectric (d33 = 280 pC/N) properties are observed for textured KNNL ceramics as compared to the randomly oriented ones. This behaviour is suggested to be due to the long range ordered domain patterns observed in the textured ceramics. The obtained results as compared with the data previously reported on texture KNN based ceramics confirm that superior properties were found due to ordered repeated domain pattern. This study provides an useful approach towards properties improvement of KNN-based piezoelectric ceramics. Overall, the present results bring a significant contribution to the pool of knowledge on the properties of sodium potassium niobate materials: a relation between the domain patterns and di-, ferro-, and piezo-electric response of single crystals and ceramics was demonstrated and ways of engineering maximised properties in KNN materials, for example by texturing were established. This contribution is envisaged to have broad implications for the expanded use of KNN over the alternative lead-based materials.

Assessing the effectiveness of chemical treatment with nanomaterials in improving the quality of different industrial effluents

Industrial activities are the major sources of pollution in all environments. Depending on the type of industry, various levels of organic and inorganic pollutants are being continuously discharged into the environment. Although, several kinds of physical, chemical, biological or the combination of methods have been proposed and applied to minimize the impact of industrial effluents, few have proved to be totally effective in terms of removal rates of several contaminants, toxicity reduction or amelioration of physical and chemical properties. Hence, it is imperative to develop new and innovative methodologies for industrial wastewater treatment. In this context nanotechnology arises announcing the offer of new possibilities for the treatment of wastewaters mainly based on the enhanced physical and chemical proprieties of nanomaterials (NMs), which can remarkably increase their adsorption and oxidation potential. Although applications of NMs may bring benefits, their widespread use will also contribute for their introduction into the environment and concerns have been raised about the intentional use of these materials. Further, the same properties that make NMs so appealing can also be responsible for producing ecotoxicological effects. In a first stage, with the objective of selecting NMs for the treatment of organic and inorganic effluents we first assessed the potential toxicity of nanoparticles of nickel oxide (NiO) with two different sizes (100 and 10-20 nm), titanium dioxide (TiO2, < 25 nm) and iron oxide (Fe2O3, ≈ 85x425 nm). The ecotoxicological assessment was performed with a battery of assays using aquatic organisms from different trophic levels. Since TiO2 and Fe2O3 were the NMs that presented lower risks to the aquatic systems, they were selected for the second stage of this work. Thus, the two NMs pre-selected were tested for the treatment of olive mill wastewater (OMW). They were used as catalyst in photodegradation systems (TiO2/UV, Fe2O3/UV, TiO2/H2O2/UV and Fe2O3/H2O2/UV). The treatments with TiO2 or Fe2O3 combined with H2O2 were the most efficient in ameliorating some chemical properties of the effluent. Regarding the toxicity to V. fischeri the highest reduction was recorded for the H2O2/UV system, without NMs. Afterwards a sequential treatment using photocatalytic oxidation with NMs and degradation with white-rot fungi was applied to OMW. This new approach increased the reduction of chemical oxygen demand, phenolic content and ecotoxicity to V. fischeri. However, no reduction in color and aromatic compounds was achieved after 21 days of biological treatment. The photodegradation systems were also applied to treat the kraft pulp mill and mining effluents. For the organic effluent the combination NMs and H2O2 had the best performances in reduction the chemical parameters as well in terms of toxicity reduction. However, for the mine effluent the best (TiO2/UV and Fe2O3/UV) were only able to significantly remove three metals (Zn, Al and Cd). Nonetheless the treatments were able of reducing the toxicity of the effluent. As a final stage, the toxicity of solid wastes formed during wastewater treatment with NMs was assessed with Chironomus riparius larvae, a representative species of the sediment compartment. Certain solid wastes showed the potential to negatively affect C. riparius survival and growth, depending on the type of effluent treated. This work also brings new insights to the use of NMs for the treatment of industrial wastewaters. Although some potential applications have been announced, many evaluations have to be performed before the upscaling of the chemical treatments with NMs.

Desenvolvimento de um carro elétrico puro: instrumentação e registos energéticos

Desde meados do século XX os avanços na indústria automóvel trazem a associação da eletrónica sendo esta cada vez mais necessária. Com este trabalho pretende-se construir um computador de bordo de um veículo elétrico dando continuação a uma dissertação anterior, que consistiu em um Controlador de Motor de carro elétrico com capacidade de travagem regenerativa. Este Computador deve ser de baixo custo e é destinado à instrumentação, apresentação de balanços energéticos e funções básicas de diagnóstico do estado do veículo. Foi igualmente um objetivo desenvolver uma Interface a partir de um LCD para este Computador de Bordo. No modelo de Controlador de Motor disponível foram aplicadas alterações e adições na instrumentação de forma a conseguir um diagnóstico do veículo mais preciso e extenso. Para o computador ter conhecimento do consumo e outros parâmetros relacionados com o motor e respetivo Controlador, foi necessário estabelecer uma comunicação entre ambas unidades. Antes de se implementar um protocolo de comunicação realizou-se uma pesquisa por protocolos usados na indústria automóvel, com o intuito de saber qual o mais apropriado para o presente trabalho. A tarefa seguinte consistiu em uma pesquisa por hardware com o qual desenvolver o Computador e sua Interface. Os balanços energéticos implicaram o desenvolvimento de métodos de cálculo, efetuados com os parâmetros transmitidos pelo Controlador de Motor. No final da dissertação demonstra-se todas as funcionalidades do Computador de Bordo desenvolvido e como este é utilizado.

Cultivo da Salicornia ramosissima da Ilha dos Puxadoiros®

O estágio realizado teve como premissa principal perceber o comportamento da planta face ao seu crescimento em altura da própria planta e em número em função de diferentes épocas de sementeira, e de condições de cultivo, nomeadamente de tipos de solo. O trabalho realizado inclui todo o processo desde a apanha, preparação das sementes e dos campos, e a sementeira propriamente dita. Foi acompanhado o crescimento das plantas em 3 alturas diferentes, por contagem do número de plantas e do comprimento das plantas aéreas. Igualmente foram realizadas análises da granulometria dos solos. Determinaram-se os metais pesados nos solos e nas plantas, assim como os açúcares após a hidrólise e derivatização das amostras liofilizadas, tanto da raíz como da parte aérea. Foi possível concluir que a planta nasce com maior abundância em solos franco-siltosos do que em solos franco-arenosos, onde o seu crescimento é muito pobre ou mesmo nulo. Os valores de cádmio e chumbo encontram-se a níveis adequados para o consumo humano. Coloca-se a hipótese da existência de arabinoglucoronoxilanas como constituinte da raiz desta planta.

Melhoria de procedimentos internos no laboratório do Instituto dos Vinhos do Douro e do Porto, I.P.

Este relatório foi elaborado no âmbito do estágio curricular realizado na Direção de Serviços Técnicos e de Certificação do Instituto dos Vinhos do Douro e do Porto, I.P. Teve como principal objetivo apresentar propostas de alteração de procedimentos internos do laboratório do Instituto dos Vinhos do Douro e do Porto, I.P., no sentido de reduzir o tempo de resposta às solicitações, procurando uma melhor rentabilização tanto de equipamentos como de recursos humanos. Para atingir tal objetivo, foi elaborado o diagnóstico da situação, com base na informação recolhida na Direção de Serviços Técnicos e de Certificação, incluindo os dados fornecidos pelo software GLAB que dá apoio às operações realizadas no laboratório do Instituto dos Vinhos do Douro e do Porto. Além disso, foi efetuado o acompanhamento do circuito das amostras de produtos vínicos desde a sua receção, à análise nos setores do laboratório e posterior validação dos resultados. Dado que o estudo da entrada de amostras no setor Análise Mineral foi maioritariamente inconclusivo, apurou-se o custo por análise na determinação do chumbo e, ainda, foi realizada uma simulação determinar a despesa necessária para reduzir o número de amostras analisadas de cada vez que se liga o equipamento. Foi ainda comparado o custo da determinação do parâmetro furfural, análise que tanto pode ser realizada no setor Cromatografia Gasosa como no setor Cromatografia Líquida. Para isso, foram utlizados vários testes estatísticos. Com base na avaliação efetuada foram identificadas e propostas as seguintes oportunidades de melhoria: - Automação de uma das atividades realizadas no setor Físico-Química I, atividade esta necessária à preparação das análises; - Contrabalançar a sazonalidade verificada na receção de amostras dos clientes com as amostras provenientes da Direção de Serviços de Fiscalização e Controlo; - Inserção de algumas variáveis no software GLAB. É de realçar que a proposta referente à automação de uma das atividades realizadas no setor Físico-Química foi implementada pelo IVDP. Foram, também, identificadas propostas de futuras investigações.

The role of cellular prion protein in Alzheimer’s disease

Alzheimer’s disease (AD) is the most prevalent age-related neurodegenerative disease that leads to cognitive impairment and dementia. The major defined pathological hallmark of AD is the accumulation of amyloid beta (Aβ), a neurotoxic peptide, derived from beta and gamma-secretase cleavage of the amyloid precursor protein (APP). It has been described that cellular prion protein (PrPC) plays a role in the pathogenesis of Alzheimer disease. Although, the role of PrPC is still unclear, previous studies showed contradictious results. To elucidate this issue, the main objective of the present study is to investigate the influence of a knockout of the PRNP gene in 5XFAD mice, 5xFAD mice exhibited 5 mutations related to familial Alzheimer disease. These mice show an Aβ1-42 accumulation and an increased neuronal loss during aging. To create a bi-transgenic 5xFAD mice were crossed with Prnp0/0 Zurich 1 mice (prion protein knockout mice). We subjected two transgenic mice (5xFAD and Prnp0/05xFAD) at different ages (3, 9 and 12 months of age) to a battery of task to evaluate cognitive and motoric deficits and a biochemical analysis (ELISA, western blot and immunohistochemistry) to investigate the regulation and potential involvement of downstream signaling proteins in the Aβ induced toxicity process dependent of the PrPC concentration. The study revealed that the deficits induced by Aβ mediated toxicity appeared earlier in 5xFAD mice (9 months of age) than in Prnp0/05xFAD (12 months of age). Investigating the amount of amyloid beta in 5xFAD mice we observed a PrPC dependent regulation in 9 month-old animals of Aβ1−40 but not of the toxic form Aβ1−42. We did not found in Prnp0/05xFAD mice the up-regulation of P-Fyn, Fyn or Cav-1 as we found in 5xFAD mice. This suggests an important role of PrPC in Alzheimer’s disease as a promoter of toxic effect of Aβ oligomers. Our results may suggest the loss of PrPC delays the toxicity of amyloid beta. In conclusion, our data support a role of PrPC as a mediator of Aβ toxicity in AD by promoting early onset of disease.

Functional alkali tantalate 2D structures for microelectronics and related applications

Alkali tantalates and niobates, including K(Ta / Nb)O3, Li(Ta / Nb)O3 and Na(Ta / Nb)O3, are a very promising ferroic family of lead-free compounds with perovskite-like structures. Their versatile properties make them potentially interesting for current and future application in microelectronics, photocatalysis, energy and biomedics. Among them potassium tantalate, KTaO3 (KTO), has been raising interest as an alternative for the well-known strontium titanate, SrTiO3 (STO). KTO is a perovskite oxide with a quantum paraelectric behaviour when electrically stimulated and a highly polarizable lattice, giving opportunity to tailor its properties via external or internal stimuli. However problems related with the fabrication of either bulk or 2D nanostructures makes KTO not yet a viable alternative to STO. Within this context and to contribute scientifically to the leverage tantalate based compounds applications, the main goals of this thesis are: i) to produce and characterise thin films of alkali tantalates by chemical solution deposition on rigid Si based substrates, at reduced temperatures to be compatible with Si technology, ii) to fulfil scientific knowledge gaps in these relevant functional materials related to their energetics and ii) to exploit alternative applications for alkali tantalates, as photocatalysis. In what concerns the synthesis attention was given to the understanding of the phase formation in potassium tantalate synthesized via distinct routes, to control the crystallization of desired perovskite structure and to avoid low temperature pyrochlore or K-deficient phases. The phase formation process in alkali tantalates is far from being deeply analysed, as in the case of Pb-containing perovskites, therefore the work was initially focused on the process-phase relationship to identify the driving forces responsible to regulate the synthesis. Comparison of phase formation paths in conventional solid-state reaction and sol-gel method was conducted. The structural analyses revealed that intermediate pyrochlore K2Ta2O6 structure is not formed at any stage of the reaction using conventional solid-state reaction. On the other hand in the solution based processes, as alkoxide-based route, the crystallization of the perovskite occurs through the intermediate pyrochlore phase; at low temperatures pyrochlore is dominant and it is transformed to perovskite at >800 °C. The kinetic analysis carried out by using Johnson-MehlAvrami-Kolmogorow model and quantitative X-ray diffraction (XRD) demonstrated that in sol-gel derived powders the crystallization occurs in two stages: i) at early stage of the reaction dominated by primary nucleation, the mechanism is phase-boundary controlled, and ii) at the second stage the low value of Avrami exponent, n ~ 0.3, does not follow any reported category, thus not permitting an easy identification of the mechanism. Then, in collaboration with Prof. Alexandra Navrotsky group from the University of California at Davis (USA), thermodynamic studies were conducted, using high temperature oxide melt solution calorimetry. The enthalpies of formation of three structures: pyrochlore, perovskite and tetragonal tungsten bronze K6Ta10.8O30 (TTB) were calculated. The enthalpies of formation from corresponding oxides, ∆Hfox, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -203.63 ± 2.84 kJ/mol, - 358.02 ± 3.74 kJ/mol, and -1252.34 ± 10.10 kJ/mol, respectively, whereas from elements, ∆Hfel, for KTaO3, KTa2.2O6 and K6Ta10.8O30 are -1408.96 ± 3.73 kJ/mol, -2790.82 ± 6.06 kJ/mol, and -13393.04 ± 31.15 kJ/mol, respectively. The possible decomposition reactions of K-deficient KTa2.2O6 pyrochlore to KTaO3 perovskite and Ta2O5 (reaction 1) or to TTB K6Ta10.8O30 and Ta2O5 (reaction 2) were proposed, and the enthalpies were calculated to be 308.79 ± 4.41 kJ/mol and 895.79 ± 8.64 kJ/mol for reaction 1 and reaction 2, respectively. The reactions are strongly endothermic, indicating that these decompositions are energetically unfavourable, since it is unlikely that any entropy term could override such a large positive enthalpy. The energetic studies prove that pyrochlore is energetically more stable phase than perovskite at low temperature. Thus, the local order of the amorphous precipitates drives the crystallization into the most favourable structure that is the pyrochlore one with similar local organization; the distance between nearest neighbours in the amorphous or short-range ordered phase is very close to that in pyrochlore. Taking into account the stoichiometric deviation in KTO system, the selection of the most appropriate fabrication / deposition technique in thin films technology is a key issue, especially concerning complex ferroelectric oxides. Chemical solution deposition has been widely reported as a processing method to growth KTO thin films, but classical alkoxide route allows to crystallize perovskite phase at temperatures >800 °C, while the temperature endurance of platinized Si wafers is ~700 °C. Therefore, alternative diol-based routes, with distinct potassium carboxylate precursors, was developed aiming to stabilize the precursor solution, to avoid using toxic solvents and to decrease the crystallization temperature of the perovskite phase. Studies on powders revealed that in the case of KTOac (solution based on potassium acetate), a mixture of perovskite and pyrochlore phases is detected at temperature as low as 450 °C, and gradual transformation into monophasic perovskite structure occurs as temperature increases up to 750 °C, however the desired monophasic KTaO3 perovskite phase is not achieved. In the case of KTOacac (solution with potassium acetylacetonate), a broad peak is detected at temperatures <650 °C, characteristic of amorphous structures, while at higher temperatures diffraction lines from pyrochlore and perovskite phases are visible and a monophasic perovskite KTaO3 is formed at >700 °C. Infrared analysis indicated that the differences are due to a strong deformation of the carbonate-based structures upon heating. A series of thin films of alkali tantalates were spin-coated onto Si-based substrates using diol-based routes. Interestingly, monophasic perovskite KTaO3 films deposited using KTOacac solution were obtained at temperature as low as 650 °C; films were annealed in rapid thermal furnace in oxygen atmosphere for 5 min with heating rate 30 °C/sec. Other compositions of the tantalum based system as LiTaO3 (LTO) and NaTaO3 (NTO), were successfully derived as well, onto Si substrates at 650 °C as well. The ferroelectric character of LTO at room temperature was proved. Some of dielectric properties of KTO could not be measured in parallel capacitor configuration due to either substrate-film or filmelectrode interfaces. Thus, further studies have to be conducted to overcome this issue. Application-oriented studies have also been conducted; two case studies: i) photocatalytic activity of alkali tantalates and niobates for decomposition of pollutant, and ii) bioactivity of alkali tantalate ferroelectric films as functional coatings for bone regeneration. Much attention has been recently paid to develop new type of photocatalytic materials, and tantalum and niobium oxide based compositions have demonstrated to be active photocatalysts for water splitting due to high potential of the conduction bands. Thus, various powders of alkali tantalates and niobates families were tested as catalysts for methylene blue degradation. Results showed promising activities for some of the tested compounds, and KNbO3 is the most active among them, reaching over 50 % degradation of the dye after 7 h under UVA exposure. However further modifications of powders can improve the performance. In the context of bone regeneration, it is important to have platforms that with appropriate stimuli can support the attachment and direct the growth, proliferation and differentiation of the cells. In lieu of this here we exploited an alternative strategy for bone implants or repairs, based on charged mediating signals for bone regeneration. This strategy includes coating metallic 316L-type stainless steel (316L-SST) substrates with charged, functionalized via electrical charging or UV-light irradiation, ferroelectric LiTaO3 layers. It was demonstrated that the formation of surface calcium phosphates and protein adsorption is considerably enhanced for 316L-SST functionalized ferroelectric coatings. Our approach can be viewed as a set of guidelines for the development of platforms electrically functionalized that can stimulate tissue regeneration promoting direct integration of the implant in the host tissue by bone ingrowth and, hence contributing ultimately to reduce implant failure.