Investigation of Finish-cut of Microelectrodischarge Milling for Nano Surface Finish

In this article, the machining conditions to achieve nanometric surface roughness in finish cut microelectrodischarge milling were investigated. For a constant gap voltage, the effect of feed rate and capacitance was studied on average surface roughness (Ra) and maximum peak-to-valley roughness height (Ry). Statistical models were developed using a three-level, two-factor experimental design. The developed models minimized Ra and Ry by desirability function approach. Maximum desirability was found to be more than 98%. The minimum values of Ra and Ry were 23 and 173 nm, respectively, for 1.00 μm s-1 feed rate and 0.01 nF capacitance. Verification experiments were conducted to check the accuracy of the models, where the responses were found to be very close to the predicted values. Thus, the developed models can be used to generate nanometric level surface finish, which are useful for many applications in microelectromechanical systems.

Thin film capacitor cut from single crystals using focused ion beam milling

The focused ion beam microscope (FIB) has been used to fabricate thin parallel-sided ferroelectric capacitors from single crystals of BaTiO3 and SrTiO3. A series of nano-sized capacitors ranging in thickness from similar to660 nm to similar to300 nm were made. Cross-sectional high resolution transmission electron microscopy (HRTEM) revealed that during capacitor fabrication, the FIB rendered around 20 nm of dielectric at the electrode-dielectric interface amorphous, associated with local gallium impregnation. Such a region would act electrically in series with the single crystal and would presumably have a considerable negative influence on the dielectric properties. However, thermal annealing prior to gold electrodes deposition was found to fully recover the single crystal capacitors and homogenise the gallium profile. The dielectric testing of the STO ultra-thin single crystal capacitors was performed yielding a room temperature dielectric constant of similar to300, as is the case in bulk. Therefore, there was no evidence of a collapse in dielectric constant associated with thin film dimensions.

Cut down by some cowardly miscreants’: Plant maiming, or the Malicious Cutting of Plants as an Act of Protest in Eighteenth and Nineteenth Century Rural England

Since the publication of Hobsbawm and Rudé's Captain Swing our understanding of the role(s) of covert protests in Hanoverian rural England has advanced considerably. Whilst we now know much about the dramatic practices of incendiarism and animal maiming and the voices of resistance in seemingly straightforward acquisitive acts, one major gap remains. Despite the fact that almost thirty years have passed since E. P. Thompson brought to our attention that under the notorious ‘Black Act’ the malicious cutting of trees was a capital offence, no subsequent research has been published. This paper seeks to address this major lacuna by systematically analysing the practices and patterns of malicious attacks on plants (‘plant maiming’) in the context of late eighteenth- and early nineteenth-century southern England. It is shown that not only did plant maiming take many different forms, attacking every conceivable type of flora, but also that it was universally understood and practised. In some communities plant maiming was the protestors' weapon of choice. As a social practice it therefore embodied wider community beliefs regarding the defence of plebeian livelihoods and identities.

Effect of Free-Fall Height in Water on Performance of Flowable Concrete

Concrete placed under water should be proportioned to flow readily into place with minimum materials separation. Unlike concrete cast for deep tremie seals, the use of concrete in repairs often necessitates some free fall of the mixture through water. Such placement conditions lead to greater risk of water erosion and segregation, and should be addressed in proportioning highly flowable underwater concrete. This paper evaluates the effect of free-fall height (FFH) of concrete through water on resulting in-place properties. Concrete was cast in blocks measuring 0.54 x 0.44 x 1 m with the initial FFH in water ranging between 0.25 and 0.60 m. In-place compressive and splitting tensile strengths, unit weight, and depth of washed-out and sedimentation materials were determined. In total, 24 highly flowable mixtures with slump flows greater than 500 mm were investigated. The evaluated mixtures were prepared with various hydraulic binders, including conventional Type 10 cement, a binary mixture with 10% of silica fume (SF), and a ternary binder incorporating 20% of fly ash (FA) and 6% of SF. The mixtures were proportioned with water-binder ratios (w/b) ranging between 0.41 and 0.47. Test results show that the increase of FFH of fresh concrete in water can greatly decrease the residual strength and significantly increase the thickness of washed out and sedimentation materials. The incorporation of 10% of SF, or 20% of FA and 6% of SF, and the reduction of the w/b from 0.47 to 0.41 can, however, lead to a significant increase in washout resistance and residual strength. A relationship between residual strength and the coupled factor of free-fall drop of concrete in water and washout resistance is established.

An Unkind Cut: Circumcision, Death and the Impact of Irish Health Policy on Asylum Seekers

Healthcare and the wider social determinants of health are the keystone of a number of complex progressive social justice issues that evoke complex emotions. As the demography of Ireland rapidly changes, the practices and expectations of some asylum seekers presents new opportunities for the providers of health service provision and reform. This paper looks at some of the emotions evoked in health care issues and draws on observations and interviews from empirical fieldwork carried out for the Health Research Board. The research was conducted both in the Adelaide and Meath Hospital, incorporating the National Children’s Hospital, Tallaght and in a number of refugee reception centres in Ireland. At one level honouring faith choices within a healthcare setting is a societal acknowledgement made to people at their most vulnerable, that the potent and cathartic transformative rituals they value are significant in mediating and managing their emotions - at another level, it is a practical and a symbolic communication of a statutory commitment to inter-culturalism and community cohesion..

A refined physical model of the clarinet using a variable air jet height

A time-domain formulation of a lumped model ap-
proximation of a clarinet reed excitation mechanism is presented.
The lumped model is based on an analytical representation of
the ow within the reed channel, incorporating a contraction
coefcient (vena contracta factor) that is dened as the ratio of
the effective ow over the Bernoulli ow. This coefcient has
been considered to be constant in previous studies focusing on
sound synthesis. In this paper it will be treated as a function
of the reed opening, varying between 0 and 1 as predicted by
boundary layer ow theory. Focussing on a specic mouthpiece
geometry, the effect of modelling a variable air jet height on the
synthesised sound is analysed.