Australia and New Zealand CBNG development and environmental implications

Following the success of Coalbed Natural Gas (CBNG) operations in the United States, companies in Australia and New Zealand have been actively exploring and developing this technology for the last two decades. In particular, the Bowen and Surat basins in Queensland, Australia, have undergone extensive CBNG development. Unfortunately, awareness of potential environmental problems associated with CBNG abstraction has not been widespread and legislation has at times struggled to keep up with rapid development. In Australia, the combined CBNG resource for both the Bowen and Surat basins has been estimated at approximately 10,500 PJ with gas content as high as 10 m3/tonne of coal. There are no official estimates for the magnitude of the CBNG resource in New Zealand but initial estimates suggest this could be up to 1,300 PJ with gas content ranging from 1 to 5 m3/tonne of coal. In Queensland, depressurization of the Walloon Coal Measures to recover CBNG has the potential to induce drawdown in adjacent deep aquifer systems through intraformational groundwater flow. In addition, CBNG operators have been disposing their co-produced water by using large unlined ponds, which is not the best practice for managing co-produced water. CBNG waters in Queensland have the typical geochemical signature associated with CBNG waters (Van Voast, 2003) and thus have the potential to impair soils and plant growth where land disposal is considered. Water quality from exploration wells in New Zealand exhibit the same characteristics although full scale production has not yet begun. In general, the environmental impacts that could arise from CBNG water extraction depend on the aquifer system, the quantity and quality of produced water, and on the method of treatment and disposal being used. Understanding these impacts is necessary to adequately manage CBNG waters so that environmental effects are minimized; if properly managed, CBNG waters can be used for beneficial applications and can become a valuable resource to stakeholders.

Weighted fairness with MCR guarantee and a general-purpose explicit rate allocation algorithm for ATM ABR service

In this paper, weighted fair rate allocation for ATM available bit rate (ABR) service is discussed with the concern of the minimum cell rate (MCR). Weighted fairness with MCR guarantee has been discussed recently in the literature. In those studies, each ABR virtual connection (VC) is first allocated its MCR, then the remaining available bandwidth is further shared among ABR VCs according to their weights. For the weighted fairness defined in this paper, the bandwidth is first allocated according to each VC's weight; if a VC's weighted share is less than its MCR, it should be allocated its MCR instead of the weighted share. This weighted fairness with MCR guarantee is referred to as extended weighted (EXW) fairness. Certain theoretical issues related to EXW, such as its global solution and bottleneck structure, are first discussed in the paper. A distributed explicit rate allocation algorithm is then proposed to achieve EXW fairness in ATM networks. The algorithm is a general-purpose explicit rate algorithm in the sense that it can realise almost all the fairness principles proposed for ABR so far whilst only minor modifications may be needed.

A general-purpose simulator for train operations

Computer simulation has been widely accepted as an essential tool for the analysis of many engineering systems. It is nowadays perceived to be the most readily available and feasible means of evaluating operations in real railway systems. Based on practical experience and theoretical models developed in various applications, this paper describes the design of a general-purpose simulation system for train operations. Its prime objective is to provide a single comprehensive computer-aided engineering tool for most studies on railway operations so that various aspects of the railway systems with different operation characteristics can be investigated and analysed in depth. This system consists of three levels of simulation. The first is a single-train simulator calculating the running time of a train between specific points under different track geometry and traction conditions. The second is a dual-train simulator which is to find the minimum headway between two trains under different movement constraints, such as signalling systems. The third is a whole-system multi-train simulator which carries out process simulation of the real operation of a railway system according to a practical or planned train schedule or headway; and produces an overall evaluation of system performance.

Creative, culture tourism and place-making : Istanbul and London film industries

During the last decade many cities have sought to promote creativity by encouraging creative industries as drivers for economic and spatial growth. Among the creative industries, film industry play an important role in establishing high level of success in economic and spatial development of cities by fostering endogenous creativeness, attracting exogenous talent, and contributing to the formation of places that creative cities require. The paper aims to scrutinize the role of creative industries in general and the film industry in particular for place making, spatial development, tourism, and the formation of creative cities, their clustering and locational decisions. This paper investigates the positive effects of the film industry on tourism such as incubating creativity potential, increasing place recognition through locations of movies filmed and film festivals hosted, attracting visitors and establishing interaction among visitors, places and their cultures. This paper reveals the preliminary findings of two case studies from Beyoglu, Istanbul and Soho, London, examines the relation between creativity, tourism, culture and the film industry, and discusses their effects on place-making and tourism.

Skills for creative industries graduate success

Purpose: Although there is increasing evidence that the creative industries are essential to national economic growth as well as social and cultural well-being, creative graduates often find it difficult to become established professionally. This study investigates the value of career management competence and intrinsic career motivations (as elements of ‘protean career orientation’) in predicting positive graduate outcomes. ----- ----- Design/methodology: Self-report surveys were administered to 208 creative industries graduates from two Australian universities at two points in time: at course completion, and one year later. ----- ----- Findings: Individual career management competence and intrinsic work motivations, measured at course completion, were significant predictors of early career success, using both subjective and objective measures, measured one year later. ----- ----- Practical implications: This study suggests that an emphasis on student development beyond the traditional ‘key’ employability skills may well be worthwhile. The article also suggests a broad learning and teaching approach by which universities can encourage the development of student career identity, and thus engender student intrinsic career motivations and career self management skills and behaviours. ----- ----- Originality/value: This is one of the first studies to demonstrate empirically a link between a particular set of skills and graduate outcomes. In addition, it provides insights into the role of student career motivations in positive transitions to the world of work in the creative industries.

Three-dimensional hydrogen-bonded structures in the guanidinium salts of the monocyclic dicarboxylic acids rac-trans-cyclohexane-1,2-dicarboxylic acid (2:1, anhydrous), isophthalic acid (1:1, monohydrate) and terephthalic acid (2:1, trihydrate).

The structures of bis(guanidinium)rac-trans-cyclohexane-1,2-dicarboxylate, 2(CH6N3+) C8H10O4- (I), guanidinium 3-carboxybenzoate monohydrate CH6N3+ C8H5O4- . H2O (II) and bis(guanidinium) benzene-1,4-dicarboxylate trihydrate, 2(CH6N3+) C8H4O4^2- . 3H2O (III) have been determined and the hydrogen bonding in each examined. All three compounds form three-dimensional hydrogen-bonded framework structures. In anhydrous (I), both guanidinium cations give classic cyclic R2/2(8) N--H...O,O'(carboxyl) and asymmetric cyclic R1/2(6) hydrogen-bonding interactions while one cation gives an unusual enlarged cyclic interaction with O acceptors of separate ortho-related carboxyl groups [graph set R2/2(11)]. Cations and anions also associate across inversion centres giving cyclic R2/4(8) motifs. In the 1:1 guanidinium salt (II), the cation gives two separate cyclic R1/2(6) interactions, one with a carboxyl O-acceptor, the other with the water molecule of solvation. The structure is unusual in that both carboxyl groups give short inter-anion O...H...O contacts, one across a crystallographic inversion centre [2.483(2)\%A], the other about a two-fold axis of rotation [2.462(2)\%A] with a half-occupancy hydrogen delocalized on the symmetry element in each. The water molecule links the cation--anion ribbon structures into a three-dimensional framework. In (III), the repeating molecular unit comprises a benzene-1,4-dicarboxylate dianion which lies across a crystallographic inversion centre, two guanidinium cations and two water molecules of solvation (each set related by two-fold rotational symmetry), and a single water molecule which lies on a two-fold axis. Each guanidinium cation gives three types of cyclic interactions with the dianions: one R^1^~2~(6), the others R2/3(8) and R3/3(10) (both of these involving the water molecules), giving a three-dimensional structure through bridges down the b cell direction. The water molecule at the general site also forms an unusual cyclic R2/2(4) homodimeric association across an inversion centre [O--H...O, 2.875(2)\%A]. The work described here provides further examples of the common cyclic guanidinium cation...carboxylate anion hydrogen-bonding associations as well as featuring other less common cyclic motifs.

Bis(4-carbamoylpiperidinium)biphenyl-4,4'-disulfonate

In the title isonipecotamide salt 2C6H13N2O+.C12H8O6S22-,the asymmetric unit comprises one biphenyl-4,4'-disulfonate dianion which lies across a crystallographic inversion centre and another in a general position [dihedral angle between the two phenyl rings is 37.1(1)deg], together with three isonipecotamide cations. Two of these cations give a cyclic homomeric amide-amide dimer interaction [graph set R2/2(8)],the other giving a similar dimeric interaction but across an inversion centre, both dimers then forming lateral cyclic R2/4(8) pyrimidinium N-H...O interactions. These units are linked longitudinally to the sulfonate groups of the dianions through piperidinium N-H...O hydrogen bonds, giving a three-dimensional framework structure.

Morphological investigations of supported titania photocatalysts

Due in no small part to an increasing need to augment existing water purification strategies, the synthesis of titania photocatalysts has been under considerable examination. However, in order to make the use of titania photocatalysts commercially viable there needs to be an increase in the efficiency of the catalysts while decreasing the potential toxicity. Due to its high porosity and novel optical properties, inverse opal titania derived from colloidal crystal templating offers one of the most efficient solutions. While a number of synthesis methods for inverse opal titania have been presented in the literature, the co�]deposition method offers the most effective method of generating the relative large areas of inverse opal material. The factors which affect the codeposition method and the mechanism by which titania inverse opals form in general remain relatively unstudied. This manuscript presents an examination of the morphology of inverse opals generated by the co�]deposition method while proposing a mechanism by which the inverse structures form.

Optimism about safety and group-serving interpretations of safety among pedestrians and cyclists in relation to road use in general and under low light conditions

Drivers are known to be optimistic about their risk of crash involvement, believing that they are less likely to be involved in a crash than other drivers. However, little comparative research has been conducted among other road users. In addition, optimism about crash risk is conceptualised as applying only to an individual’s assessment of his or her personal risk of crash involvement. The possibility that the self-serving nature of optimism about safety might be generalised to the group-level as a cyclist or a pedestrian, i.e., becoming group-serving rather than self-serving, has been overlooked in relation to road safety. This study analysed a subset of data collected as part of a larger research project on the visibility of pedestrians, cyclists and road workers, focusing on a set of questionnaire items administered to 406 pedestrians, 838 cyclists and 622 drivers. The items related to safety in various scenarios involving drivers, pedestrians and cyclists, allowing predictions to be derived about group differences in agreement with items based on the assumption that the results would exhibit group-serving bias. Analysis of the responses indicated that specific hypotheses about group-serving interpretations of safety and responsibility were supported in 22 of the 26 comparisons. When the nine comparisons relevant to low lighting conditions were considered separately, seven were found to be supported. The findings of the research have implications for public education and for the likely acceptance of messages which are inconsistent with current assumptions and expectations of pedestrians and cyclists. They also suggest that research into group-serving interpretations of safety, even for temporary roles rather than enduring groups, could be fruitful. Further, there is an implication that gains in safety can be made by better educating road users about the limitations of their visibility and the ramifications of this for their own road safety, particularly in low light.

Embracing diversity : empowering preservice teachers for teaching gifted and talented students

This study investigated preservice teachers’ perceptions for teaching and sustaining gifted and talented students while developing, modifying and implementing activities to cater for the diverse learner. Participants were surveyed at the end of a gifted and talented education program on their perceptions to differentiate the curriculum for meeting the needs of the student (n=22). SPSS data analysis with the five-part Likert scale indicated these preservice teachers agreed or strongly agreed they had developed skills in curriculum planning (91%) with well-designed activities (96%), and lesson preparation skills (96%). They also claimed they were enthusiastic for teaching (91%) and understanding of school practices and policies (96%). However, 46% agreed they had knowledge of syllabus documents with 50% claiming an ability to provide written feedback on student’s learning. Furthermore, nearly two-thirds suggested they had educational language from the syllabus and effective student management strategies. Preservice teachers require more direction on how to cater for diversity and begin creating sustainable societies by building knowledge from direct GAT experiences. Designing diagnostic surveys associated with university coursework can be used to determine further development for specific preservice teacher development in GAT education. Preservice teachers need to create opportunities for students to realise their potential by involving cognitive challenges through a differentiated curriculum. Differentiation requires modification of four primary areas of curriculum development (Maker, 1975) content (what we teach), process (how we teach), product (what we expect the students to do or show) and learning environment (where we teach/our class culture). Ashman and Elkins (2009) and Glasson (2008) emphasise the need for preservice teachers, teachers and other professionals to be able to identify what gifted and talented (GAT) students know and how they learn in relation to effective teaching. Glasson (2008) recommends that educators keep up to date with practices in pedagogy, support, monitoring and profiling of GAT students to create an environment conducive to achieving. Oral feedback is one method to communicate to learners about their progress but has advantages and disadvantages for some students. Oral feedback provides immediate information to the student on progress and performance (Ashman & Elkins, 2009). However, preservice teachers must have clear understandings of key concepts to assist the GAT student. Implementing teaching strategies to engage innovate and extend students is valuable to the preservice teacher in focusing on GAT student learning in the classroom (Killen, 2007). Practical teaching strategies (Harris & Hemming, 2008; Tomlinson et al., 1994) facilitate diverse ways for assisting GAT students to achieve learning outcomes. Such strategies include activities to enhance creativity, co-operative learning and problem-solving activities (Chessman, 2005; NSW Department of Education and Training, 2004; Taylor & Milton, 2006) for GAT students to develop a sense of identity, belonging and self esteem towards becoming an autonomous learner. Preservice teachers need to understand that GAT students learn in a different way and therefore should be assessed differently. Assessment can be through diverse options to demonstrate the student’s competence, demonstrate their understanding of the material in a way that highlights their natural abilities (Glasson, 2008; Mack, 2008). Preservice teachers often are unprepared to assess students understanding but this may be overcome with teacher education training promoting effective communication and collaboration in the classroom, including the provision of a variety of assessment strategies to improve teaching and learning (Callahan et al., 2003; Tomlinson et al., 1994). It is also critical that preservice teachers have enthusiasm for teaching to demonstrate inclusion, involvement and the excitement to communicate to GAT students in the learning process (Baum, 2002). Evaluating and reflecting on teaching practices must be part of a preservice teacher’s repertoire for GAT education. Evaluating teaching practices can assist to further enhance student learning (Mayer, 2008). Evaluation gauges the success or otherwise of specific activities and teaching in general (Mayer, 2008), and ensures that preservice teachers and teachers are well prepared and maintain their commitment to their students and the community. Long and Harris (1999) advocate that reflective practices assist teachers in creating improvements in educational practices. Reflective practices help preservice teachers and teachers to improve their ability to pursue improved learning outcomes and professional growth (Long & Harris, 1999). Context This study is set at a small regional campus of a large university in Queensland. As a way to address departmental policies and the need to prepare preservice teachers for engaging a diverse range of learners (see Queensland College of Teachers, Professional Standards for Teachers, 2006), preservice teachers at this campus completed four elective units within their Bachelor of Education (primary) degree. The electives include: 1. Middle years students and schools 2. Teaching strategies for engaging learners 3. Teaching students with learning difficulties, and 4. Middle-years curriculum, pedagogy and assessment. In the university-based component of this unit, preservice teachers engaged in learning about middle years students and schools, and gained knowledge of government policies pertaining to GAT students. Further explored within in this unit was the importance of: collaboration between teachers, parents/carers and school personnel in supporting middle years GAT students; incorporating challenging learning experiences that promoted higher order thinking and problem solving skills; real world learning experiences for students and; the alignment and design of curriculum, pedagogy and assessment that is relevant to the students development, interests and needs. The participants were third-year Bachelor of Education (primary) preservice teachers who were completing an elective unit as part of the middle years of schooling learning with a focus on GAT students. They were assigned one student from a local school. In the six subsequent ninety minute weekly lessons, the preservice teachers were responsible for designing learning activities that would engage and extend the GAT students. Furthermore, preservice teachers made decisions about suitable pedagogical approaches and designed the assessment task to align with the curriculum and the developmental needs of their middle years GAT student. This research aims to describe preservice teachers’ perceptions of their education for teaching gifted and talented students.

Organometallic macrocyclic chemistry. 8.(1) : an unusual metallacycle derived from phosphine−alkynyl thioether coupling

The α,ω-diyne 4,7,10-trithiatrideca-2,11-diyne reacts with [RuCl2(PPh3)3] and KPF6 to form the phosphonio-substituted metallatricyclic salt [RuCl(PPh3){κ4C,S,S′,S′′-S(C≡CMe)C2H4SC2H4SC(PPh3)CMe}]PF6 arising from the activation of one alkynyl group toward nucleophilic attack by extraneous phosphine.

Primary students' success on the structured number line

Number lines are part of our everyday life (e.g., thermometers, kitchen scales) and are frequently used in primary mathematics as instructional aids, in texts and for assessment purposes on mathematics tests. There are two major types of number lines; structured number lines, which are the focus of this paper, and empty number lines. Structured number lines represent mathematical information by the placement of marks on a horizontal or vertical line which has been marked into proportional segments (Figure 1). Empty number lines are blank lines which students can use for calculations (Figure 2) and are not discussed further here (see van den Heuvel-Panhuizen, 2008, on the role of empty number lines). In this article, we will focus on how students’ knowledge of the structured number line develops and how they become successful users of this mathematical tool.