Theory of radar imaging using time-frequency distribution

The concept of radar was developed for the estimation of the distance (range) and velocity of a target from a receiver. The distance measurement is obtained by measuring the time taken for the transmitted signal to propagate to the target and return to the receiver. The target's velocity is determined by measuring the Doppler induced frequency shift of the returned signal caused by the rate of change of the time- delay from the target. As researchers further developed conventional radar systems it become apparent that additional information was contained in the backscattered signal and that this information could in fact be used to describe the shape of the target itself. It is due to the fact that a target can be considered to be a collection of individual point scatterers, each of which has its own velocity and time- delay. DelayDoppler parameter estimation of each of these point scatterers thus corresponds to a mapping of the target's range and cross range, thus producing an image of the target. Much research has been done in this area since the early radar imaging work of the 1960s. At present there are two main categories into which radar imaging falls. The first of these is related to the case where the backscattered signal is considered to be deterministic. The second is related to the case where the backscattered signal is of a stochastic nature. In both cases the information which describes the target's scattering function is extracted by the use of the ambiguity function, a function which correlates the backscattered signal in time and frequency with the transmitted signal. In practical situations, it is often necessary to have the transmitter and the receiver of the radar system sited at different locations. The problem in these situations is 'that a reference signal must then be present in order to calculate the ambiguity function. This causes an additional problem in that detailed phase information about the transmitted signal is then required at the receiver. It is this latter problem which has led to the investigation of radar imaging using time- frequency distributions. As will be shown in this thesis, the phase information about the transmitted signal can be extracted from the backscattered signal using time- frequency distributions. The principle aim of this thesis was in the development, and subsequent discussion into the theory of radar imaging, using time- frequency distributions. Consideration is first given to the case where the target is diffuse, ie. where the backscattered signal has temporal stationarity and a spatially white power spectral density. The complementary situation is also investigated, ie. where the target is no longer diffuse, but some degree of correlation exists between the time- frequency points. Computer simulations are presented to demonstrate the concepts and theories developed in the thesis. For the proposed radar system to be practically realisable, both the time- frequency distributions and the associated algorithms developed must be able to be implemented in a timely manner. For this reason an optical architecture is proposed. This architecture is specifically designed to obtain the required time and frequency resolution when using laser radar imaging. The complex light amplitude distributions produced by this architecture have been computer simulated using an optical compiler.

Repair of calvarial defects with customized tissue-engineered bone grafts - I. Evaluation of osteogenesis in a three-dimensional culture system

Bone generation by autogenous cell transplantation in combination with a biodegradable scaffold is one of the most promising techniques being developed in craniofacial surgery. The objective of this combined in vitro and in vivo study was to evaluate the morphology and osteogenic differentiation of bone marrow derived mesenchymal progenitor cells and calvarial osteoblasts in a two-dimensional (2-D) and three-dimensional (3-D) culture environment (Part I of this study) and their potential in combination with a biodegradable scaffold to reconstruct critical-size calvarial defects in an autologous animal model [Part II of this study; see Schantz, J.T., et al. Tissue Eng. 2003;9(Suppl. 1):S-127-S-139; this issue]. New Zealand White rabbits were used to isolate osteoblasts from calvarial bone chips and bone marrow stromal cells from iliac crest bone marrow aspirates. Multilineage differentiation potential was evaluated in a 2-D culture setting. After amplification, the cells were seeded within a fibrin matrix into a 3-D polycaprolactone (PCL) scaffold system. The constructs were cultured for up to 3 weeks in vitro and assayed for cell attachment and proliferation using phase-contrast light, confocal laser, and scanning electron microscopy and the MTS cell metabolic assay. Osteogenic differentiation was analyzed by determining the expression of alkaline phosphatase (ALP) and osteocalcin. The bone marrow-derived progenitor cells demonstrated the potential to be induced to the osteogenic, adipogenic, and chondrogenic pathways. In a 3-D environment, cell-seeded PCL scaffolds evaluated by confocal laser microscopy revealed continuous cell proliferation and homogeneous cell distribution within the PCL scaffolds. On osteogenic induction mesenchymal progenitor cells (12 U/L) produce significantly higher (p < 0.05) ALP activity than do osteoblasts (2 U/L); however, no significant differences were found in osteocalcin expression. In conclusion, this study showed that the combination of a mechanically stable synthetic framework (PCL scaffolds) and a biomimetic hydrogel (fibrin glue) provides a potential matrix for bone tissue-engineering applications. Comparison of osteogenic differentiation between the two mesenchymal cell sources revealed a similar pattern.

Non-linear oscillations assessment of the distribution static compensator operating in voltage control mode

This article deals with the non-linear oscillations assessment of a distribution static comensator ooperating in voltage control mode using the bifurcation theory. A mathematical model of the distribution static compensator in the voltage control mode to carry out the bifurcation analysis is derived. The stabiity regions in the Thevein equivalent plane are computed. In addition, the stability regions in the control gains space, as well as the contour lines for different Floquet multipliers are computed. The AC and DC capacitor impacts on the stability are analyzed through the bifurcation theory. The observations are verified through simulaation studies. The computation of the stability region allows the assessment of the stable operating zones for a power system that includes a distribution static compensator operating in the voltage mode.

Spatial analysis of melioidosis distribution in a suburban area

Burkholderia pseudomallei, the causative agent of melioidosis is associated with soil. This study used a geographic information system (GIS) to determine the spatial distribution of clinical cases of melioidosis in the endemic suburban region of Townsville in Australia. A total of 65 cases over the period 1996–2008 were plotted using residential address. Two distinct groupings were found. One was around the base of a hill in the city centre and the other followed the old course of a major waterway in the region. Both groups (accounting for 43 of the 65 cases examined) are in areas expected to have particularly wet topsoils following intense rainfall, due to soil type or landscape position.

Mobile communication in power distribution application

This paper investigates how to interface the wireless application protocol (WAP) architecture to the SCADA system running distributed network protocol (DNP) in a power process plant. DNP is a well-developed protocol to be applied in the supervisory control and data acquisition (SCADA) system but the system control centre and remote terminal units (RTUs) are presently connected through a local area network. The conditions in a process plant are harsh and the site is remote. Resources for data communication are difficult to obtain under these conditions, thus, a wireless channel communication through a mobile phone is practical and efficient in a process plant environment. The mobile communication industries and the public have a strong interest in the WAP technology application in mobile phone networks and the WAP application programming interface (API) in power industry applications is one area that requires extensive investigation.

Perfusion model system to generate engineered grafts with controlled cellular distributions

Engineered tissue grafts, which mimic the spatial variations of cell density and extracellular matrix present in native tissues, could facilitate more efficient tissue regeneration and integration. We previously demonstrated that cells could be uniformly seeded throughout a 3D scaffold having a random pore architecture using a perfusion bioreactor2. In this work, we aimed to generate 3D constructs with defined cell distributions based on rapid prototyped scaffolds manufactured with a controlled gradient in porosity. Computational models were developed to assess the influence of fluid flow, associated with pore architecture and perfusion regime, on the resulting cell distribution.

Spatial distribution of suicide in Queensland, Australia

Background: There has been a lack of investigation into the spatial distribution and clustering of suicide in Australia, where the population density is lower than many countries and varies dramatically among urban, rural and remote areas. This study aims to examine the spatial distribution of suicide at a Local Governmental Area (LGA) level and identify the LGAs with a high relative risk of suicide in Queensland, Australia, using geographical information system (GIS) techniques.---------- Methods: Data on suicide and demographic variables in each LGA between 1999 and 2003 were acquired from the Australian Bureau of Statistics. An age standardised mortality (ASM) rate for suicide was calculated at the LGA level. GIS techniques were used to examine the geographical difference of suicide across different areas.---------- Results: Far north and north-eastern Queensland (i.e., Cook and Mornington Shires) had the highest suicide incidence in both genders, while the south-western areas (i.e., Barcoo and Bauhinia Shires) had the lowest incidence in both genders. In different age groups (≤24 years, 25 to 44 years, 45 to 64 years, and ≥65 years), ASM rates of suicide varied with gender at the LGA level. Mornington and six other LGAs with low socioeconomic status in the upper Southeast had significant spatial clusters of high suicide risk.---------- Conclusions: There was a notable difference in ASM rates of suicide at the LGA level in Queensland. Some LGAs had significant spatial clusters of high suicide risk. The determinants of the geographical difference of suicide should be addressed in future research.

Crossing boundaries to explore sustainable architecture by open system design

This paper argues a model of open system design for sustainable architecture, based on a thermodynamics framework of entropy as an evolutionary paradigm. The framework can be simplified to stating that an open system evolves in a non-linear pattern from a far-from-equilibrium state towards a non-equilibrium state of entropy balance, which is a highly ordered organization of the system when order comes out of chaos. This paper is work in progress on a PhD research project which aims to propose building information modelling for optimization and adaptation of buildings environmental performance as an alternative sustainable design program in architecture. It will be used for efficient distribution and consumption of energy and material resource in life-cycle buildings, with the active involvement of the end-users and the physical constraints of the natural environment.

Optimal voltage support mechanism in distribution networks

Optimal scheduling of voltage regulators (VRs), fixed and switched capacitors and voltage on customer side of transformer (VCT) along with the optimal allocaton of VRs and capacitors are performed using a hybrid optimisation method based on discrete particle swarm optimisation and genetic algorithm. Direct optimisation of the tap position is not appropriate since in general the high voltage (HV) side voltage is not known. Therefore, the tap setting can be determined give the optimal VCT once the HV side voltage is known. The objective function is composed of the distribution line loss cost, the peak power loss cost and capacitors' and VRs' capital, operation and maintenance costs. The constraints are limits on bus voltage and feeder current along with VR taps. The bus voltage should be maintained within the standard level and the feeder current should not exceed the feeder-rated current. The taps are to adjust the output voltage of VRs between 90 and 110% of their input voltages. For validation of the proposed method, the 18-bus IEEE system is used. The results are compared with prior publications to illustrate the benefit of the employed technique. The results also show that the lowest cost planning for voltage profile will be achieved if a combination of capacitors, VRs and VCTs is considered.

Designing a workflow system using coloured petri nets

Traditional workflow systems focus on providing support for the control-flow perspective of a business process, with other aspects such as data management and work distribution receiving markedly less attention. A guide to desirable workflow characteristics is provided by the well-known workflow patterns which are derived from a comprehensive survey of contemporary tools and modelling formalisms. In this paper we describe the approach taken to designing the newYAWL workflow system, an offering that aims to provide comprehensive support for the control-flow, data and resource perspectives based on the workflow patterns. The semantics of the newYAWL workflow language are based on Coloured Petri Nets thus facilitating the direct enactment and analysis of processes described in terms of newYAWL language constructs. As part of this discussion, we explain how the operational semantics for each of the language elements are embodied in the newYAWL system and indicate the facilities required to support them in an operational environment. We also review the experiences associated with developing a complete operational design for an offering of this scale using formal techniques.

Inclusion of PMU current phasor measurements in a power system state estimator

Three different methods of inclusion of current measurements by phasor measurement units (PMUs) in a power sysetm state estimator is investigated. A comprehensive formulation of the hybrid state estimator incorporating conventional, as well as PMU measurements, is presented for each of the three methods. The behaviour of the elements because of the current measurements in the measurement Jacobian matrix is examined for any possible ill-conditioning of the state estimator gain matrix. The performance of the state estimators are compared in terms of the convergence properties and the varian in the estimated states. The IEEE 14-bus and IEEE 300-bus systems are used as test beds for the study.

Digital dawn : a revolution in movie distribution?

How will the digital technology revolution impact the movie business? Hollywood developed a highly successful industrial system that has functioned well for almost a century in the sense that it enabled the Major film studios to largely control and dominate the industry. However, the new digital technology may now be propelling Hollywood toward the biggest technological transition since the creation of the studio system almost a century ago. For example, Major Hollywood studios are already beginning to provide video-on-demand (VOD) digital distribution of movies over the Internet. This article examines what is happening, and why. It sets out the background and the incipient changes already occurring. It makes an argument regarding the fundamental strategic dynamics, that acetate film was the key to the control of the Hollywood system, and speculates about how a shift away from acetate film to digital video may transform that system. The focus is on the impact on how the Major studios release and market their movies, and how new market and marketing opportunities for the low-budget independent filmmaking sector may arise.

Assessment of corneal dynamics with high-speed swept source optical coherence tomography combined with an air puff system

We present a novel method and instrument for in vivo imaging and measurement of the human corneal dynamics during an air puff. The instrument is based on high-speed swept source optical coherence tomography (ssOCT) combined with a custom adapted air puff chamber from a non-contact tonometer, which uses an air stream to deform the cornea in a non-invasive manner. During the short period of time that the deformation takes place, the ssOCT acquires multiple A-scans in time (M-scan) at the center of the air puff, allowing observation of the dynamics of the anterior and posterior corneal surfaces as well as the anterior lens surface. The dynamics of the measurement are driven by the biomechanical properties of the human eye as well as its intraocular pressure. Thus, the analysis of the M-scan may provide useful information about the biomechanical behavior of the anterior segment during the applanation caused by the air puff. An initial set of controlled clinical experiments are shown to comprehend the performance of the instrument and its potential applicability to further understand the eye biomechanics and intraocular pressure measurements. Limitations and possibilities of the new apparatus are discussed.

Independent cinema in the Chinese film industry

Chinese independent cinema has developed for more than twenty years. Two sorts of independent cinema exist in China. One is underground cinema, which is produced without official approvals and cannot be circulated in China, and the other are the films which are legally produced by small private film companies and circulated in the domestic film market. This sort of ‘within-system’ independent cinema has played a significant role in the development of Chinese cinema in terms of culture, economics and ideology. In contrast to the amount of comment on underground filmmaking in China, the significance of ‘within-system’ independent cinema has been underestimated by most scholars. This thesis is a study of how political management has determined the development of Chinese independent cinema and how Chinese independent cinema has developed during its various historical trajectories. This study takes media economics as the research approach, and its major methods utilise archive analysis and interviews. The thesis begins with a general review of the definition and business of American independent cinema. Then, after a literature review of Chinese independent cinema, it identifies significant gaps in previous studies and reviews issues of traditional definition and suggests a new definition. After several case studies on the changes in the most famous Chinese directors’ careers, the thesis shows that state studios and private film companies are two essential domestic backers for filmmaking in China. After that, the body of the thesis provides an examination of the development of ‘within-system’ independent cinema. Specifically, three factors: government intervention, the majors’ performance (state studios and, later, the conglomerates) and the market conduct of independent cinema at various points in their trajectories are studied. The key findings of the study are as follows: First, most scholars have overlooked the existence and the significance of within-system Chinese independent cinema. Drawing on an American definition of the independent sector, this thesis proposes a definition of the sector in China: namely, any film that has not been financed, produced, and/or distributed by majors. The thesis also notes important contradictions in applying this definition: i.e. film-making is still dependent on policies that frame industry development. The thesis recognises that major tensions apply to filmmaking in China, which significantly differentiates the Chinese independents from those in the US. Second, the development of Chinese independent cinema is the result the rise of the private sector and the decline of the state studio system. As state studios encountered difficulties the private sector moved forward; consequently the environment improved for independent cinema. Third, before 2003, the film industry in China had little commercialisation. The government controlled independent cinema by means of license and censorship. State studios produced main melody films and Hollywood attracted most of the audiences. Many independent filmmakers focused on commercial films, thus contributing to film commercialisation. Fourth, after 2003, the film industry became increasingly fragmented. The government created distribution and exhibition opportunities for main melody films; conglomerates collaborated with Hong Kong players; Hong Kong co-productions and Hollywood occupied the film market; and small private film companies produced main melody films in order to earn meagre profits. The original contribution of the thesis is to advance the study of Chinese independent cinema. The study suggests a reasonable and practical definition of Chinese independent cinema. It shows how the Chinese government authorities have implemented economic measures to gain ideological control in the film industry. Finally, this the first study on Chinese independent cinema applying a synthesis of economic, political and historical perspectives.