The influence of temperature and introduction point on the detection of Rhyzopertha dominica in stored grain

The presence of insect pests in grain storages throughout the supply chain is a significant problem for farmers, grain handlers, and distributors world-wide. Insect monitoring and sampling programmes are used in the stored grains industry for the detection and estimation of pest populations. At the low pest densities dictated by economic and commercial requirements, the accuracy of both detection and abundance estimates can be influenced by variations in the spatial structure of pest populations over short distances. Geostatistical analysis of Rhyzopertha dominica populations in 2 and 3 dimensions showed that insect numbers were positively correlated over short (0.5 cm) distances, and negatively correlated over longer (.10 cm) distances. At 35 C, insects were located significantly further from the grain surface than at 25 and 30 C. Dispersion metrics showed statistically significant aggregation in all cases. The observed heterogeneous spatial distribution of R. dominica may also be influenced by factors such as the site of initial infestation and disturbance during handling. To account for these additional factors, I significantly extended a simulation model that incorporates both pest growth and movement through a typical stored-grain supply chain. By incorporating the effects of abundance, initial infestation site, grain handling, and treatment on pest spatial distribution, I developed a supply chain model incorporating estimates of pest spatial distribution. This was used to examine several scenarios representative of grain movement through a supply chain, and determine the influence of infestation location and grain disturbance on the sampling intensity required to detect pest infestations at various infestation rates. This study has investigated the effects of temperature, infestation point, and grain handling on the spatial distribution and detection of R. dominica. The proportion of grain infested was found to be dependent upon abundance, initial pest location, and grain handling. Simulation modelling indicated that accounting for these factors when developing sampling strategies for stored grain has the potential to significantly reduce sampling costs while simultaneously improving detection rate, resulting in reduced storage and pest management cost while improving grain quality.

Open and networked initiatives and the digital transformation of academic publishing in China

Many aspects of China's academic publishing system differ from the systems found in liberal market based economies of the United States, Western Europe and Australia. A high level of government intervention in both the publishing industry and academia and the challenges associated with attempting to make a transition from a centrally controlled towards a more market based publishing industry are two notable differences; however, as in other countries, academic communities and publishers are being transformed by digital technologies. This research explores the complex yet dynamic digital transformation of academic publishing in China, with a specific focus of the open and networked initiatives inspired by Web 2.0 and social media. The thesis draws on two case studies: Science Paper Online, a government-operated online preprint platform and open access mandate; and New Science, a social reference management website operated by a group of young PhD students. Its analysis of the innovations, business models, operating strategies, influences, and difficulties faced by these two initiatives highlights important characteristics and trends in digital publishing experiments in China. The central argument of this thesis is that the open and collaborative possibilities of Web 2.0 inspired initiatives are emerging outside the established journal and monograph publishing system in China, introducing innovative and somewhat disruptive approaches to the certification, communication and commercial exploitation of knowledge. Moreover, emerging publishing models are enabling and encouraging a new system of practising and communicating science in China, putting into practice some elements of the Open Science ethos. There is evidence of both disruptive change to old publishing structures and the adaptive modification of emergent replacements in the Chinese practice. As such, the transformation from traditional to digital and interactive modes of publishing, involves both competition and convergence between new and old publishers, as well as dynamics of co-evolution involving new technologies, business models, social norms, and government reform agendas. One key concern driving this work is whether there are new opportunities and new models for academic publishing in the Web 2.0 age and social media environment, which might allow the basic functions of communication and certification to be achieved more effectively. This thesis enriches existing knowledge of open and networked transformations of scholarly publishing by adding a Chinese story. Although the development of open and networked publishing platforms in China remains in its infancy, the lessons provided by this research are relevant to practitioners and stakeholders interested in understanding the transformative dynamics of networked technologies for publishing and advocating open access in practice, not only in China, but also internationally.

Exploring pedestrian accessibility and walkability : insight from public place observations in inner-urban higher density Brisbane, Australia

As planners work to create more sustainable and liveable urban environments, a priority is to transition away from prioritising the automobile and towards enhancing the pedestrian experience. Thus, this research explores the experience of pedestrian accessibility in inner-urban higher-density Brisbane in Australia, drawing on findings from semi-structured in-depth interviews with 24 residents and over 100 hours of public place observations in three case-study neighbourhoods. The interviews took place in residents homes and explored their experience of higher density living and their neighbourhood, whilst observations were recorded through a combination of methods including photographs, sketch maps, recordings and field journals. Observation locations included retail and commercial space, roads, parkland and open space, with multiple observations at each location. A thematic analysis identified common themes in both interviews and the observations, with this paper focusing on residents’ lived experience in urban built environments. This analysis revealed that pedestrian accessibility is linked to access to local amenities and direct routes, aesthetics, sense of community, ownership of space and safety. In particular, observations revealed how pedestrian accessibility and route-taking works with, against or in spite of the design features of urban environments, as well as the importance of the social use of the built environment. Residents spoke about although walking quick and preferred for local amenities, the decision to walk was moderated by factors such as time of day and perceived safety. Measures to ensure and improve the pedestrian accessibility of urban areas needs to take into account the propensity for people to prefer and improvise direct routes (often to the detriment of traffic safety considerations), the importance of ongoing maintenance and upgrading of walking infrastructure and the importance of aesthetically pleasing and safe walking environments. By combining interviews and observations, this research highlights the current dominance of the automobile culture in Brisbane and the layers of meaning, experiences and complexity hidden within the pedestrian experience.

A brief guide to synchrotron radiation-based microtomography in (structural) geology and rock mechanics

This contribution outlines Synchrotron-based X-ray micro-tomography and its potential use in structural geology and rock mechanics. The paper complements several recent reviews of X-ray microtomography. We summarize the general approach to data acquisition, post-processing as well as analysis and thereby aim to provide an entry point for the interested reader. The paper includes tables listing relevant beamlines, a list of all available imaging techniques, and available free and commercial software packages for data visualization and quantification. We highlight potential applications in a review of relevant literature including time-resolved experiments and digital rock physics. The paper concludes with a report on ongoing developments and upgrades at synchrotron facilities to frame the future possibilities for imaging sub-second processes in centimetre-sized samples.

Design of light gauge steel roofing systems subject to high wind forces

Light gauge steel roofing systems made of thin profiled roof sheeting and battens are used commonly in residential, industrial and commercial buildings. Their critical design load combination is that due to wind uplift forces that occur during high wind events such as tropical cyclones and thunderstorms. However, premature local failures at their screw connections have been a concern for many decades since cyclone Tracy that devastated Darwin in 1974. Extensive research that followed cyclone Tracy on the pull-through and pull-out failures of roof sheeting to batten connections has significantly improved the safety of roof sheeting. However, this has made the batten to rafter/truss connection the weakest, and recent wind damage investigations have shown the failures of these connections and the resulting loss of entire roof structures. Therefore an experimental research program using both small scale and full scale air-box tests is currently under way to investigate the pull-through failures of thin-walled steel battens under high wind uplift forces. Tests have demonstrated that occurrence of pull-through failures in the bottom flanges of steel batttens and the need to develop simple test and design methods as a function of many critical parameters such as steel batten geometry, thickness and grade, screw fastener sizes and other fastening details. This paper presents the details of local failures that occur in light fauge roofing systems, a review of the current design and test methods for steel battens and associated short comings, and the test results obtained to date on pull-through failures of battens from small scale and full scale tests. Finally, it proposes the use of suitable small scale test methods that can be used by both researchers and manufacturers of such screw-fastened light gauge steel batten systems.

Gentrification and the artistic dividend : the role of the arts in neighborhood change

Problem, research strategy, and findings: There is a conflict between recent creative placemaking policies intended to promote positive neighborhood development through the arts and the fact that the arts have long been cited as contributing to gentrification and the displacement of lower-income residents. Unfortunately, we do not have data to demonstrate widespread evidence of either outcome. We address the dearth of comprehensive research and inform neighborhood planning efforts by statistically testing how two different groups of arts activities—the fine arts and commercial arts industries—are associated with conditions indicative of revitalization and gentrification in 100 large U.S. metropolitan areas. We find that different arts activities are associated with different types and levels of neighborhood change. Commercial arts industries show the strongest association with gentrification in rapidly changing areas, while the fine arts are associated with stable, slow-growth neighborhoods. Takeaway for practice: This research can help planners to more effectively incorporate the arts into neighborhood planning efforts and to anticipate the potential for different outcomes in their arts development strategies, including gentrification-related displacement.

Development of gas sensing technology for ground and airborne applications powered by solar energy : methodology and experimental results

Monitoring gases for environmental, industrial and agricultural fields is a demanding task that requires long periods of observation, large quantity of sensors, data management, high temporal and spatial resolution, long term stability, recalibration procedures, computational resources, and energy availability. Wireless Sensor Networks (WSNs) and Unmanned Aerial Vehicles (UAVs) are currently representing the best alternative to monitor large, remote, and difficult access areas, as these technologies have the possibility of carrying specialised gas sensing systems, and offer the possibility of geo-located and time stamp samples. However, these technologies are not fully functional for scientific and commercial applications as their development and availability is limited by a number of factors: the cost of sensors required to cover large areas, their stability over long periods, their power consumption, and the weight of the system to be used on small UAVs. Energy availability is a serious challenge when WSN are deployed in remote areas with difficult access to the grid, while small UAVs are limited by the energy in their reservoir tank or batteries. Another important challenge is the management of data produced by the sensor nodes, requiring large amount of resources to be stored, analysed and displayed after long periods of operation. In response to these challenges, this research proposes the following solutions aiming to improve the availability and development of these technologies for gas sensing monitoring: first, the integration of WSNs and UAVs for environmental gas sensing in order to monitor large volumes at ground and aerial levels with a minimum of sensor nodes for an effective 3D monitoring; second, the use of solar energy as a main power source to allow continuous monitoring; and lastly, the creation of a data management platform to store, analyse and share the information with operators and external users. The principal outcomes of this research are the creation of a gas sensing system suitable for monitoring any kind of gas, which has been installed and tested on CH4 and CO2 in a sensor network (WSN) and on a UAV. The use of the same gas sensing system in a WSN and a UAV reduces significantly the complexity and cost of the application as it allows: a) the standardisation of the signal acquisition and data processing, thereby reducing the required computational resources; b) the standardisation of calibration and operational procedures, reducing systematic errors and complexity; c) the reduction of the weight and energy consumption, leading to an improved power management and weight balance in the case of UAVs; d) the simplification of the sensor node architecture, which is easily replicated in all the nodes. I evaluated two different sensor modules by laboratory, bench, and field tests: a non-dispersive infrared module (NDIR) and a metal-oxide resistive nano-sensor module (MOX nano-sensor). The tests revealed advantages and disadvantages of the two modules when used for static nodes at the ground level and mobile nodes on-board a UAV. Commercial NDIR modules for CO2 have been successfully tested and evaluated in the WSN and on board of the UAV. Their advantage is the precision and stability, but their application is limited to a few gases. The advantages of the MOX nano-sensors are the small size, low weight, low power consumption and their sensitivity to a broad range of gases. However, selectivity is still a concern that needs to be addressed with further studies. An electronic board to interface sensors in a large range of resistivity was successfully designed, created and adapted to operate on ground nodes and on-board UAV. The WSN and UAV created were powered with solar energy in order to facilitate outdoor deployment, data collection and continuous monitoring over large and remote volumes. The gas sensing, solar power, transmission and data management systems of the WSN and UAV were fully evaluated by laboratory, bench and field testing. The methodology created to design, developed, integrate and test these systems was extensively described and experimentally validated. The sampling and transmission capabilities of the WSN and UAV were successfully tested in an emulated mission involving the detection and measurement of CO2 concentrations in a field coming from a contaminant source; the data collected during the mission was transmitted in real time to a central node for data analysis and 3D mapping of the target gas. The major outcome of this research is the accomplishment of the first flight mission, never reported before in the literature, of a solar powered UAV equipped with a CO2 sensing system in conjunction with a network of ground sensor nodes for an effective 3D monitoring of the target gas. A data management platform was created using an external internet server, which manages, stores, and shares the data collected in two web pages, showing statistics and static graph images for internal and external users as requested. The system was bench tested with real data produced by the sensor nodes and the architecture of the platform was widely described and illustrated in order to provide guidance and support on how to replicate the system. In conclusion, the overall results of the project provide guidance on how to create a gas sensing system integrating WSNs and UAVs, how to power the system with solar energy and manage the data produced by the sensor nodes. This system can be used in a wide range of outdoor applications, especially in agriculture, bushfires, mining studies, zoology, and botanical studies opening the way to an ubiquitous low cost environmental monitoring, which may help to decrease our carbon footprint and to improve the health of the planet.

Experimental investigation of post-fire mechanical properties of cold-formed steels

Cold-formed steel members are widely used in residential, industrial and commercial buildings as primary load-bearing elements. During fire events, they will be exposed to elevated temperatures. If the general appearance of the structure is satisfactory after a fire event then the question that has to be answered is how the load bearing capacity of cold-formed steel members in these buildings has been affected. Hence after such fire events there is a need to evaluate the residual strength of these members. However, the post-fire behaviour of cold-formed steel members has not been investigated in the past. This means conservative decisions are likely to be made in relation to fire exposed cold-formed steel buildings. Therefore an experimental study was undertaken to investigate the post-fire mechanical properties of cold-formed steels. Tensile coupons taken from cold-formed steel sheets of three different steel grades and thicknesses were exposed to different elevated temperatures up to 800 oC, and were then allowed to cool down to ambient temperature before they were tested to failure. Tensile coupon tests were conducted to obtain their post-fire stress-strain curves and associated mechanical properties (yield stress, Young’s modulus, ultimate strength and ductility). It was found that the post-fire mechanical properties of cold-formed steels are reduced below the original ambient temperature mechanical properties if they had been exposed to temperatures exceeding 300 oC. Hence a new set of equations is proposed to predict the post-fire mechanical properties of cold-formed steels. Such post-fire mechanical property assessments allow structural and fire engineers to make an accurate prediction of the safety of fire exposed cold-formed steel buildings. This paper presents the details of this experimental study and the results of post-fire mechanical properties of cold-formed steels. It also includes the results of a post-fire evaluation of cold-formed steel walls.

Proposed MBMs for reduction of greenhouse gas emissions from international shipping and the WTO rules

The international shipping sector is a major contributor to global greenhouse gas (GHG) emissions. The International Maritime Organisation (IMO) has adopted some technical and operational measures to reduce GHG emissions from international shipping. However, these measures may not be enough to reduce the amount of GHG emissions from international shipping to an acceptable level. Therefore, the IMO Member States are currently considering a number of proposals for the introduction of market-based measures (MBMs). During the negotiation process, some leading developing countries raised questions about the probable confl ict of the proposed MBMs with the rules of the World Trade Organisation (WTO). This article comprehensively examines this issue and argues that none of the MBM proposals currently under consideration by the IMO has any confl ict with the WTO rules.

Barriers to bikesharing : an analysis from Melbourne and Brisbane

This study quantifies the motivators and barriers to bikeshare program usage in Australia. An online survey was administered to a sample of annual members of Australia’s two bikeshare programs based in Brisbane and Melbourne, to assess motivations for joining the schemes. Non-members of the programs were also sampled in order to identify current barriers to joining bikeshare. Spatial analysis from Brisbane revealed residential and work locations of non-members were more geographically dispersed than for bikeshare members. An analysis of bikeshare usage in Melbourne showed a strong relationship between docking stations in areas with relatively less accessible public transit opportunities. The most influential barriers to bikeshare use related to motorized travel being too convenient and docking stations not being sufficiently close to home, work and other frequented destinations. The findings suggest that bikeshare programs may attract increased membership by ensuring travel times are competitive with motorized travel, for example through efficient bicycle routing and priority progression and, by expanding docking station locations, and by increasing the level of convenience associated with scheme use. Convenience considerations may include strategic location of docking stations, ease of signing up and integration with public transport.

Post-fire mechanical properties of cold-formed steels

Cold-formed steel members have been widely used in residential, industrial and commercial buildings as primary load-bearing and non-load bearing structural elements. These buildings must be properly evaluated after a fire event to assess the nature and extent of structural damage. If the general appearance of the structure is satisfactory after a fire event then the question that has to be answered is how the structural capacity of cold-formed steel members in these buildings has been affected. Elevated temperatures during a fire event affect the structural performance of cold-formed steel members even after cooling down to ambient temperature due to the possible detrimental changes in their mechanical properties. However, the post-fire behaviour of cold-formed steel members has not been investigated in the past and hence there is a need to investigate the post-fire mechanical properties of cold-formed steels. Therefore an experimental study was undertaken at the Queensland University of Technology to understand the residual mechanical properties of cold-formed steels after fire events. Tensile coupon tests were conducted on three different steel grades and thicknesses to obtain their stress-strain curves and relevant mechanical properties after cooling them down from different elevated temperatures. It was found that the post-fire mechanical properties of cold-formed steels are different to the original ambient temperature mechanical properties. Hence a new set of equations is proposed to predict the reduced mechanical properties of cold-formed steels after a fire event.

Improving the shear capacities of lipped channel beams with web openings using plate stiffeners

Cold-formed steel lipped channel beams (LCB) are used extensively in residential, industrial and commercial buildings as load bearing structural elements. Their shear capacities are considerably reduced when web openings are included for the purpose of locating building services. Past research has shown that the shear capacities of LCBs were reduced by up to 70% due to the inclusion of these web openings. Hence there is a need to improve the shear capacities of LCBs with web openings. A cost effective way of eliminating the detrimental effects of large web openings is to attach suitable stiffeners around the web openings and restore the original shear strength and stiffness of LCBs. Hence detailed experimental studies were undertaken to investigate the behaviour and strength of LCBs with stiffened web openings subject to shear, and combined bending and shear actions. Both plate and stud stiffeners with varying sizes and thicknesses were attached to the web elements of LCBs using different screw-fastening arrangements. Simply supported test specimens of LCBs with aspect ratios of 1.0 and 1.5 were loaded at mid-span until failure. Numerical studies were also undertaken to investigate the strength of LCBs with stiffened web openings. Finite element models of LCBs with stiffened web openings under shear, combined bending and shear actions were developed to simulate the behaviour of tested LCBs. The developed models were then validated by comparing their results with experimental results and used in further studies. Both experimental and finite element analysis results showed that the stiffening arrangements recommended by past research and available design guidelines are not adequate to restore the original shear strengths of LCBs. Therefore new stiffener arrangements were proposed based on screw fastened plate stiffeners. This paper presents the details of this research study and the results.

A rapid and cost-effective method of producing recombinant proBNP and NT-proBNP variants in Escherichia coli for immunoassay of heart failure

The measurements of plasma natriuretic peptides (NT-proBNP, proBNP and BNP) are used to diagnose heart failure but these are expensive to produce. We describe a rapid, cheap and facile production of proteins for immunoassays of heart failure. DNA encoding N-terminally His-tagged NT-proBNP and proBNP were cloned into the pJexpress404 vector. ProBNP and NT-proBNP peptides were expressed in Escherichia coli, purified and refolded in vitro. The analytical performance of these peptides were comparable with commercial analytes (NT-proBNP EC50 for the recombinant is 2.6 ng/ml and for the commercial material is 5.3 ng/ml) and the EC50 for recombinant and commercial proBNP, are 3.6 and 5.7 ng/ml respectively). Total yield of purified refolded NT-proBNP peptide was 1.75 mg/l and proBNP was 0.088 mg/l. This approach may also be useful in expressing other protein analytes for immunoassay applications. To develop a cost effective protein expression method in E. coli to obtain high yields of NT-proBNP (1.75 mg/l) and proBNP (0.088 mg/l) peptides for immunoassay use.

Lindquist and Pytel

The foremost event in the international architecture calendar is the Venice International Architecture Biennale. In 2012, Creative Directors Gerard Reinmuth and Anthony Burke with TOKO Concept Design, led the Australian Pavilion exhibition, entitled FORMATIONS: New Practices in Australian Architecture. The exhibition focus was to explore and celebrate “the nature of innovative configurations of architectural practice in Australia today and the desire for a renewed form of architectural agency which drives them”. The Australian Pavilion exhibition purposely chose to highlight the actions and processes behind contemporary architectural practice, focusing not on ‘starchitecture’ projects but those far reaching and socially-engaged “practitioners who are making a substantial and consequential impact in the field and well beyond it”. FORMATIONS had two overarching themes: (1) to stimulate critical disciplinary commentary on a range of new types of Australian practices and their potentialities and (2) exciting a public audience with a spatially dynamic and thought provoking exhibition of new forms of architectural practice, their spatial consequences and transformative potentials. Six projects were displayed in the Australian Pavilion in Venice, with the printed catalogue showcasing 33 ground-breaking examples of Australian practitioners addressing internationally relevant issues in their practice. Lindquist and Pytels collaborative practice is programmed between the demands of academia and commercial fashion practice. Their interests lie in exploring the relationship between the body, new materiality and its application within different facts of design production. The creative practice is underpinned by scholarly theory such as Heidegger’s "nearness and revealing" (1927-1954), Simondon’s "transduction theory" (1989) and the Burke's "sublime" (1757). Outcomes feedback into academic studio programs, scholarly research and material development for commercial, installation and speculative design production.

The rise of englightened shareholder primacy and its impact on US corporate self-regulation

Enlightened shareholder primacy (“ESP”) is a new approach in the corporate governance (“CG”) framework. The emergence of this approach is important owing to its role in answering a vital question: is the company really a private organisation to be seen only through the economic prism of contract? Or is it public and about a wider group of interests and underwritten by communitarian concern about social responsibility? Apart from answering this question, ESP explains the changes in corporate directors’ roles and self-regulation strategies of companies.