Pore structure characterization of North American shale gas reservoirs using USANS/SANS, gas adsorption, and mercury intrusion

Small-angle and ultra-small-angle neutron scattering (SANS and USANS), low-pressure adsorption (N2 and CO2), and high-pressure mercury intrusion measurements were performed on a suite of North American shale reservoir samples providing the first ever comparison of all these techniques for characterizing the complex pore structure of shales. The techniques were used to gain insight into the nature of the pore structure including pore geometry, pore size distribution and accessible versus inaccessible porosity. Reservoir samples for analysis were taken from currently-active shale gas plays including the Barnett, Marcellus, Haynesville, Eagle Ford, Woodford, Muskwa, and Duvernay shales. Low-pressure adsorption revealed strong differences in BET surface area and pore volumes for the sample suite, consistent with variability in composition of the samples. The combination of CO2 and N2 adsorption data allowed pore size distributions to be created for micro–meso–macroporosity up to a limit of �1000 Å. Pore size distributions are either uni- or multi-modal. The adsorption-derived pore size distributions for some samples are inconsistent with mercury intrusion data, likely owing to a combination of grain compression during high-pressure intrusion, and the fact that mercury intrusion yields information about pore throat rather than pore body distributions. SANS/USANS scattering data indicate a fractal geometry (power-law scattering) for a wide range of pore sizes and provide evidence that nanometer-scale spatial ordering occurs in lower mesopore–micropore range for some samples, which may be associated with inter-layer spacing in clay minerals. SANS/USANS pore radius distributions were converted to pore volume distributions for direct comparison with adsorption data. For the overlap region between the two methods, the agreement is quite good. Accessible porosity in the pore size (radius) range 5 nm–10 lm was determined for a Barnett shale sample using the contrast matching method with pressurized deuterated methane fluid. The results demonstrate that accessible porosity is pore-size dependent.

Assessing the Impact of Sensor Accuracy and Sensor Choice on Air Traffic Conflict Risk Estimation using Risk-Ratio Concepts

One of the primary desired capabilities of any future air traffic separation management system is the ability to provide early conflict detection and resolution effectively and efficiently. In this paper, we consider the risk of conflict as a primary measurement to be used for early conflict detection. This paper focuses on developing a novel approach to assess the impact of different measurement uncertainty models on the estimated risk of conflict. The measurement uncertainty model can be used to represent different sensor accuracy and sensor choices. Our study demonstrates the value of modelling measurement uncertainty in the conflict risk estimation problem and presents techniques providing a means of assessing sensor requirements to achieve desired conflict detection performance.

Decision-making about hormone replacement therapy by women in England and Scotland

OBJECTIVE: The aim of this study was to explore women's decision-making about the balance of risks and benefits of taking hormone replacement therapy (HRT) based on the latest evidence from the Women's Health Initiative (WHI) trial of combined HRT. METHODS: Women aged 50-69 years, who were eligible for the Women's International Study of long Duration Oestrogen after Menopause (WISDOM) trial, were invited to participate in one of eight focus groups. Participants were asked to discuss their views about taking HRT based on the latest international evidence. RESULTS AND CONCLUSIONS: Eighty-two women participated overall. Qualitative content analysis was applied to the discussion transcripts. Women regarded the decisions they make about taking HRT as highly personal, and, for women currently taking HRT, the overwhelming reason for continuation was perceived improvement in quality of life regardless of either the risks or the benefits in the longer term.

A finite element model of seat cushion indentation with a soft tissue human occupant model

Effective digital human model (DHM) simulation of automotive driver packaging ergonomics, safety and comfort depends on accurate modelling of occupant posture, which is strongly related to the mechanical interaction between human body soft tissue and flexible seat components. This paper presents a finite-element study simulating the deflection of seat cushion foam and supportive seat structures, as well as human buttock and thigh soft tissue when seated. The three-dimensional data used for modelling thigh and buttock geometry were taken on one 95th percentile male subject, representing the bivariate percentiles of the combined hip breadth (seated) and buttock-to-knee length distributions of a selected Australian and US population. A thigh-buttock surface shell based on this data was generated for the analytic model. A 6mm neoprene layer was offset from the shell to account for the compression of body tissue expected through sitting in a seat. The thigh-buttock model is therefore made of two layers, covering thin to moderate thigh and buttock proportions, but not more fleshy sizes. To replicate the effects of skin and fat, the neoprene rubber layer was modelled as a hyperelastic material with viscoelastic behaviour in a Neo-Hookean material model. Finite element (FE) analysis was performed in ANSYS V13 WB (Canonsburg, USA). It is hypothesized that the presented FE simulation delivers a valid result, compared to a standard SAE physical test and the real phenomenon of human-seat indentation. The analytical model is based on the CAD assembly of a Ford Territory seat. The optimized seat frame, suspension and foam pad CAD data were transformed and meshed into FE models and indented by the two layer, soft surface human FE model. Converging results with the least computational effort were achieved for a bonded connection between cushion and seat base as well as cushion and suspension, no separation between neoprene and indenter shell and a frictional connection between cushion pad and neoprene. The result is compared to a previous simulation of an indentation with a hard shell human finite-element model of equal geometry, and to the physical indentation result, which is approached with very high fidelity. We conclude that (a) SAE composite buttock form indentation of a suspended seat cushion can be validly simulated in a FE model of merely similar geometry, but using a two-layer hard/soft structure. (b) Human-seat indentation of a suspended seat cushion can be validly simulated with a simplified human buttock-thigh model for a selected anthropomorphism.

Patient Safety Law: From Silos to Systems

Patient safety has become a significant and pressing policy issue. Around the world, governments, the health care sector and the public are increasingly cognizant of the need to improve the safety of care delivered by their health systems. Pressure for change has been created by highly publicized incidents in a number of countries involving unsafe acts that were significant both in scale and consequence and a number of empirical studies that revealed the high rates of unsafe acts and their consequences. The costs of unsafe health care – both personal and fiscal – to individuals, their families and their communities and to the state are massive. In this research project we explored one particular avenue for change – that is, the use of legal instruments by governments to improve patient safety. We did this through a comparative review of the use of legal instruments or frameworks in other countries (specifically Australia, Denmark, New Zealand, the United Kingdom, and the United States) as well as two non-health care related sectors in Canada (transportation and occupational health and safety). We began this research by reviewing the legal instruments and undertaking extensive literature reviews. Further information was gathered through in-person interviews with policy-makers and academics in the countries studied, and from policy-makers and academics expert in the health, occupational health and safety, and transportation sectors in Canada. Once descriptions of the various countries and sectors were drafted, we held small-group meetings with local experts on particular aspects of patient safety. We then hosted a national consultation meeting. We subsequently drafted this final report and the appendices, which fully describe the results of the background research. Finally, we prepared a summary version of the report as well as posters and papers to be published and delivered at conferences and meetings with relevant groups.

Vision-based estimation of airborne target pseudobearing rate using hidden Markov model filters

The problem of estimating pseudobearing rate information of an airborne target based on measurements from a vision sensor is considered. Novel image speed and heading angle estimators are presented that exploit image morphology, hidden Markov model (HMM) filtering, and relative entropy rate (RER) concepts to allow pseudobearing rate information to be determined before (or whilst) the target track is being estimated from vision information.

Automated aerial inspection guidance with improved turn planning

Aerial inspection of pipelines, powerlines, and other large linear infrastructure networks has emerged in a number of civilian remote sensing applications. Challenges relate to automating inspection flight for under-actuated aircraft with LiDAR/camera sensor constraints whilst subjected to wind disturbances. This paper presents new improved turn planning strategies with guidance suitable for automation of linear infrastructure inspection able to reduce inspection flight distance by including wind information. Simulation and experimental flight tests confirmed the flight distance saving, and the proposed guidance strategies exhibited good tracking performance in a range of wind conditions.

Control of infrastructure inspection aircraft vertical dynamics in the presence of thermal disturbances

The low-altitude aircraft inspection of powerlines, or other linear infrastructure networks, is emerging as an important application requiring specialised control technologies. Despite some recent advances in automated control related to this application, control of the underactuated aircraft vertical dynamics has not been completely achieved, especially in the presence of thermal disturbances. Rejection of thermal disturbances represents a key challenge to the control of inspection aircraft due to the underactuated nature of the dynamics and specified speed, altitude, and pitch constraints. This paper proposes a new vertical controller consisting of a backstepping elevator controller with feedforward-feedback throttle controller. The performance of our proposed approach is evaluated against two existing candidate controllers.

HMM relative entropy rate concepts for vision-based aircraft manoeuvre detection

Machine vision is emerging as a viable sensing approach for mid-air collision avoidance (particularly for small to medium aircraft such as unmanned aerial vehicles). In this paper, using relative entropy rate concepts, we propose and investigate a new change detection approach that uses hidden Markov model filters to sequentially detect aircraft manoeuvres from morphologically processed image sequences. Experiments using simulated and airborne image sequences illustrate the performance of our proposed algorithm in comparison to other sequential change detection approaches applied to this application.

Consistent HMM parameter estimation using Kerridge inaccuracy rates

In this paper, we propose a novel online hidden Markov model (HMM) parameter estimator based on Kerridge inaccuracy rate (KIR) concepts. Under mild identifiability conditions, we prove that our online KIR-based estimator is strongly consistent. In simulation studies, we illustrate the convergence behaviour of our proposed online KIR-based estimator and provide a counter-example illustrating the local convergence properties of the well known recursive maximum likelihood estimator (arguably the best existing solution).

Hidden credential retrieval from a reusable password

We revisit the venerable question of access credentials management, which concerns the techniques that we, humans with limited memory, must employ to safeguard our various access keys and tokens in a connected world. Although many existing solutions can be employed to protect a long secret using a short password, those solutions typically require certain assumptions on the distribution of the secret and/or the password, and are helpful against only a subset of the possible attackers. After briefly reviewing a variety of approaches, we propose a user-centric comprehensive model to capture the possible threats posed by online and offline attackers, from the outside and the inside, against the security of both the plaintext and the password. We then propose a few very simple protocols, adapted from the Ford-Kaliski server-assisted password generator and the Boldyreva unique blind signature in particular, that provide the best protection against all kinds of threats, for all distributions of secrets. We also quantify the concrete security of our approach in terms of online and offline password guesses made by outsiders and insiders, in the random-oracle model. The main contribution of this paper lies not in the technical novelty of the proposed solution, but in the identification of the problem and its model. Our results have an immediate and practical application for the real world: they show how to implement single-sign-on stateless roaming authentication for the internet, in a ad-hoc user-driven fashion that requires no change to protocols or infrastructure.

Living City 2013 Workshop

Living City 2013 Workshop, as part of a school term’s design-based curriculum connected to the KGSC/QUT Design Excellence Program and run from 11 February – 1 May, 2013, was essentially a three-day place-based urban design immersion workshop program for 25 Year 11 Visual Art and Design Students and 2 Teachers from Kelvin Grove State College (KGSC) held at both Queensland University of Technology (QUT) Gardens Point Campus and The Edge, State Library of Queensland. Mentored by 4 design professionals, 2 tertiary design academics, 2 public artists, and 12 QUT tertiary design students, the workshop explored youth-inspired public space design solutions for the active Brisbane City Council redevelopment site of Queens Wharf Road precinct. As well as the face-to-face workshops, for Living City 2013, an interactive web environment was introduced to enable students to connect with each other and program mentors throughout the course of the program. The workshop, framed within notions of ecological, economic, social and cultural sustainability, aimed to raise awareness of the layered complexity and perspectives involved in the design of shared city spaces and to encourage young people to voice their own concerns as future citizens about the shape and direction of their city. The program commenced with an introductory student briefing by stakeholders and mentors at KGSC on 11 February, an introduction to site appraisal and site visit held at QUT and Queens Wharf Road on 20 February, and a follow up site analysis session on 6 March. Day 1 Workshop on April 17 at the Edge, State Library of Queensland, as part of the Design Minds partnership (http://designminds.org.au/kelvin-grove-state-college-excellence-in-art-design/), focused on mentoring team development of a concept design for a range of selected sites. Two workshops on April 22 and 23 at QUT, to develop these designs and presentation schemes, followed this. The workshop program culminated in a visual presentation of concept design ideas and discussion with a public audience in the Ideas Gallery on The Deck, King George Square during the Brisbane City Council City Centre Master Plan Ideas Fiesta on 1 May, 2013, as referenced in the Ideas Fiesta Wrap-up Report (http://www.brisbane.qld.gov.au/planning-building/planning-guidelines-tools/city-centre-master-plan/city-centre-master-plan-ideas-fiesta). Students were introduced to design methodology, team thinking strategies, the scope of design practices and professions, presentation skills and post-secondary pathways, while participating teachers acquired content and design learning strategies transferable in many other contexts. The program was fully documented on the Living City website (http://www.livingcity.net.au/LC2013x/index.html) and has been recognised by the Brisbane City Council Youth Strategy 2014-2019 as a best practice model for making Brisbane a well-designed, subtropical city.

International hermelin brain tumor symposium on matricellular proteins in normal and cancer cell-matrix interactions

The second of the Hermelin Brain Tumor Center Symposia was held once again at Henry Ford Hospital in Detroit, Michigan on October 24th and 25th, 2003. A public conference was held on the 24th while a closed-door session took place on the 25th. The purpose of these symposia is to bring together experts in a particular field of study with the aim to share information with each other and the public, but then to meet privately to present novel data, hold discussions, and share concepts. While the interaction is intended to benefit all involved, the incentive is the expectation that the shared information will aid researchers at the Hermelin Brain Tumor Center in their quest to identify potential therapeutic targets and explore translational therapeutic strategies for the treatment of patients suffering nervous system tumors...

Asymptotic minimax robust and misspecified Lorden quickest change detection for dependent stochastic processes

The quick detection of an abrupt unknown change in the conditional distribution of a dependent stochastic process has numerous applications. In this paper, we pose a minimax robust quickest change detection problem for cases where there is uncertainty about the post-change conditional distribution. Our minimax robust formulation is based on the popular Lorden criteria of optimal quickest change detection. Under a condition on the set of possible post-change distributions, we show that the widely known cumulative sum (CUSUM) rule is asymptotically minimax robust under our Lorden minimax robust formulation as a false alarm constraint becomes more strict. We also establish general asymptotic bounds on the detection delay of misspecified CUSUM rules (i.e. CUSUM rules that are designed with post- change distributions that differ from those of the observed sequence). We exploit these bounds to compare the delay performance of asymptotically minimax robust, asymptotically optimal, and other misspecified CUSUM rules. In simulation examples, we illustrate that asymptotically minimax robust CUSUM rules can provide better detection delay performance at greatly reduced computation effort compared to competing generalised likelihood ratio procedures.