Interactive axial shortening of columns and walls in high rise buildings

Concrete is commonly used as a primary construction material for tall building construction. Load bearing components such as columns and walls in concrete buildings are subjected to instantaneous and long term axial shortening caused by the time dependent effects of "shrinkage", "creep" and "elastic" deformations. Reinforcing steel content, variable concrete modulus, volume to surface area ratio of the elements and environmental conditions govern axial shortening. The impact of differential axial shortening among columns and core shear walls escalate with increasing building height. Differential axial shortening of gravity loaded elements in geometrically complex and irregular buildings result in permanent distortion and deflection of the structural frame which have a significant impact on building envelopes, building services, secondary systems and the life time serviceability and performance of a building. Existing numerical methods commonly used in design to quantify axial shortening are mainly based on elastic analytical techniques and therefore unable to capture the complexity of non-linear time dependent effect. Ambient measurements of axial shortening using vibrating wire, external mechanical strain, and electronic strain gauges are methods that are available to verify pre-estimated values from the design stage. Installing these gauges permanently embedded in or on the surface of concrete components for continuous measurements during and after construction with adequate protection is uneconomical, inconvenient and unreliable. Therefore such methods are rarely if ever used in actual practice of building construction. This research project has developed a rigorous numerical procedure that encompasses linear and non-linear time dependent phenomena for prediction of axial shortening of reinforced concrete structural components at design stage. This procedure takes into consideration (i) construction sequence, (ii) time varying values of Young's Modulus of reinforced concrete and (iii) creep and shrinkage models that account for variability resulting from environmental effects. The capabilities of the procedure are illustrated through examples. In order to update previous predictions of axial shortening during the construction and service stages of the building, this research has also developed a vibration based procedure using ambient measurements. This procedure takes into consideration the changes in vibration characteristic of structure during and after construction. The application of this procedure is illustrated through numerical examples which also highlight the features. The vibration based procedure can also be used as a tool to assess structural health/performance of key structural components in the building during construction and service life.

Legal issues in carbon farming : biosequestration, carbon pricing, and carbon rights

This paper critically analyses the proposed Australian regulatory approach to the crediting of biological sequestration activities (biosequestration) under the Australian Carbon Farming Initiative and its interaction with State-based carbon rights, the national carbon-pricing mechanism, and the international Kyoto Protocol and carbon-trading markets. Norms and principles have been established by the Kyoto Protocol to guide the creation of additional, verifiable, and permanent credits from biosequestration activities. This paper examines the proposed arrangements under the Australian Carbon Farming Initiative and Carbon Pricing Mechanism to determine whether they are consistent with those international norms and standards. This paper identifies a number of anomalies associated with the legal treatment of additionality and permanence and issuance of carbon credits within the Australian schemes. In light of this, the paper considers the possible legal implications for the national and international transfer, surrender and use of these offset credits.

Queensland Business Women Stories

These projects build on the research of Klaebe and Burgess into digital story-telling, specifically variable workshop scenarios, co-creative media, participatory public history, and the development of co-creative production processes for cultural institutions. The projects represented a partnership between QUT and the State Library of Queensland. The Five Senses project focused on the distributed digital storytelling workshop model and the development of audiences for digital storytelling. The team worked with regional artists whose work had been selected for inclusion in the Five Senses exhibition at the State Library of Queensland to produce stories about their work; these works were then integrated into the physical exhibition space. The Queensland Businesswomen project produced four digital stories profiling the lives of leading Queensland businesswomen. The digital story telling workshop model was disbanded and research teams worked individually with participants to create the digital stories. Academic research and oral history interviews were conducted initially to foreground these productions. This pilot led to a larger project, Business Leaders Hall of Fame, which now has a dedicated viewing room in the SLQ sponsored by an annual silver service dinner event. With the Responses to the Apology project, which stimulated similar projects in Mt Isa and Cairns, the research team worked with Indigenous facilitators, and the participants created their digital stories with assistance from these facilitators and the QUT research team using a mix of workshop and individual meetings. The research component of the work relates to the further development of co-creative production processes for cultural institutions, involving a wide range of institutional and individual partners, while authentically representing the intensely personal perspectives of each of the primary participants. The Queensland Business Leaders Hall of Fame was a research project that included interviews with eminent Queenslanders that produced oral history interviews and digital stories about the achievements of both Queensland personalities and businesses. This model was able to test and evaluate the use of oral history and digital storytelling for learning and community heritage purposes. Interviewees include; Sir John and Valmai Pidgeon, Joseph Saragossi, Robert Bryan, Clem Jones, Jim Kennedy, Sr Angela Mary, Castelmaine Perkins, Burns and Philp, Qantas, Don Argus & Steve Irwin All digital stories, oral history interviews and transcripts were accessioned into the library collection – an international first for digital stories. Two publications in refereed journals have resulted, and the digital stories are stored in the SLQ permanent collection for the benefit of national and international scholars and the general public.

The'dream'of multi-agency crime prevention : pitfalls in policy and practice

During the 1980s, terms such as interagency or multi-agency cooperation, collaboration, coordination, and interaction have became permanent features of both crime prevention rhetoric and government crime policy. The concept of having the government, local authorities, and the community working in partnership has characterized both left and right politics for over a decade. The U.S. National Advisory Commission on Criminal Justice Standards and Goals in the U.S.. Circulars 8/84 and 44/90 released by the U.K. Home Office, and the British Morgan Report-coupled with the launch of government strategies in France, the Netherlands, England and Wales, Australia, and, more recently, in Belgium, New Zealand, and Canada-have all emphasized the importance of agencies working together to prevent or reduce crime. This paper draws upon recent Australian research and critically analyzes multi-agency crime prevention. It suggests that agency conflicts and power struggles may be exacerbated by neo-liberal economic theory, by the politics of crime prevention management, and by policies that aim to combine situational and social prevention endeavors. Furthermore, it concludes that indigenous peoples are excluded by crime prevention strategies that fail to define and interpret crime and its prevention in culturally appropriate ways.

Learning Landscapes 2.0: Adaptable educational environments

This project has blended two streams of enquiry: temporary and transportable construction technology, and flexible blended-learning environments. It seeks to develop prototypes for a series of environments suited for the activities of learning (future-proofed schools), as practiced in the twenty first century. The research utilises techniques of: historic survey, case study, first-hand observation, and architectural design (as research). The design comprises three major components: The determinate landscape: in-situ concrete ‘plate’ that is permanent. The indeterminate landscape: a kit of pre-fabricated 2-D panels assembled in a unique manner at each site to suit the client and context; manufactured to the principles of design-for-disassembly. The stations: pre-fabricated packages of highly-serviced space connected through the determinate landscape. This project was submitted to the ‘Future Proofing Schools’ competition (professional category) in October 2011. The competition was part of a research project supported under the Australian Research Council’s Linkage Grant funding scheme (project LP0991146).

Rebuilding housing after a disaster : factors for failure

Disasters, particularly those triggered by nature are often followed by a swift humanitarian relief response to address the resultant emergencies. These efforts are then transitioned through the medium recovery stage, eventually aimed at providing a long term post-disaster reconstruction solution. Emergency humanitarian relief focuses on responding to the immediate need for restoration of basic services, medical treatment and medical supplies, food and temporary shelter, and is a short term strenuous effort. Reconstruction of permanent houses, on the other hand, is a continuous process that often requires decades of effort to return a community to normality. Whilst emergency relief is generally perceived to be very effective, post-disaster housing reconstruction projects often fail to meet their set objectives. This paper outlines and discusses factors that contribute to the failure of post-disaster housing reconstruction projects and the subsequent immediate and long term negative impacts of failure on project outcomes.

The taxation of international maritime leasing profits : has the commissioners ship come in?

In light of McDermott Industries (AUST) Pty Ltd v Commissioner of Taxation, and Draft Taxation Ruling TR 2006/D8, this article considers the current Australian taxation position of profits arising from the cross-border leasing of vessels in the maritime industry. It focuses on the tax treaties to which Australia is a party, in particular the application of the business profits provisions of those treaties, and the deemed existence of a permanent establishment where substantial equipment, owned by a fiscal non-resident, is used within Australian waters.

Detecting common dynamics in transitory components

This paper considers VECMs for variables exhibiting cointegration and common features in the transitory components. While the presence of cointegration between the permanent components of series reduces the rank of the long-run multiplier matrix, a common feature among the transitory components leads to a rank reduction in the matrix summarizing short-run dynamics. The common feature also implies that there exists linear combinations of the first-differenced variables in a cointegrated VAR that are white noise and traditional tests focus on testing for this characteristic. An alternative, however, is to test the rank of the short-run dynamics matrix directly. Consequently, we use the literature on testing the rank of a matrix to produce some alternative test statistics. We also show that these are identical to one of the traditional tests. The performance of the different methods is illustrated in a Monte Carlo analysis which is then used to re-examine an existing empirical study. Finally, this approach is applied to provide a check for the presence of common dynamics in DSGE models.

Performance evaluation of onsite sewage treatment : Evaluation of current research

Efficient management of domestic wastewater is a primary requirement for human well being. Failure to adequately address issues of wastewater collection, treatment and disposal can lead to adverse public health and environmental impacts. The increasing spread of urbanisation has led to the conversion of previously rural land into urban developments and the more intensive development of semi urban areas. However the provision of reticulated sewerage facilities has not kept pace with this expansion in urbanisation. This has resulted in a growing dependency on onsite sewage treatment. Though considered only as a temporary measure in the past, these systems are now considered as the most cost effective option and have become a permanent feature in some urban areas. This report is the first of a series of reports to be produced and is the outcome of a research project initiated by the Brisbane City Council. The primary objective of the research undertaken was to relate the treatment performance of onsite sewage treatment systems with soil conditions at site, with the emphasis being on septic tanks. This report consists of a ‘state of the art’ review of research undertaken in the arena of onsite sewage treatment. The evaluation of research brings together significant work undertaken locally and overseas. It focuses mainly on septic tanks in keeping with the primary objectives of the project. This report has acted as the springboard for the later field investigations and analysis undertaken as part of the project. Septic tanks still continue to be used widely due to their simplicity and low cost. Generally the treatment performance of septic tanks can be highly variable due to numerous factors, but a properly designed, operated and maintained septic tank can produce effluent of satisfactory quality. The reduction of hydraulic surges from washing machines and dishwashers, regular removal of accumulated septage and the elimination of harmful chemicals are some of the practices that can improve system performance considerably. The relative advantages of multi chamber over single chamber septic tanks is an issue that needs to be resolved in view of the conflicting research outcomes. In recent years, aerobic wastewater treatment systems (AWTS) have been gaining in popularity. This can be mainly attributed to the desire to avoid subsurface effluent disposal, which is the main cause of septic tank failure. The use of aerobic processes for treatment of wastewater and the disinfection of effluent prior to disposal is capable of producing effluent of a quality suitable for surface disposal. However the field performance of these has been disappointing. A significant number of these systems do not perform to stipulated standards and quality can be highly variable. This is primarily due to houseowner neglect or ignorance of correct operational and maintenance procedures. The other problems include greater susceptibility to shock loadings and sludge bulking. As identified in literature a number of design features can also contribute to this wide variation in quality. The other treatment processes in common use are the various types of filter systems. These include intermittent and recirculating sand filters. These systems too have their inherent advantages and disadvantages. Furthermore as in the case of aerobic systems, their performance is very much dependent on individual houseowner operation and maintenance practices. In recent years the use of biofilters has attracted research interest and particularly the use of peat. High removal rates of various wastewater pollutants have been reported in research literature. Despite these satisfactory results, leachate from peat has been reported in various studies. This is an issue that needs further investigations and as such biofilters can still be considered to be in the experimental stage. The use of other filter media such as absorbent plastic and bark has also been reported in literature. The safe and hygienic disposal of treated effluent is a matter of concern in the case of onsite sewage treatment. Subsurface disposal is the most common and the only option in the case of septic tank treatment. Soil is an excellent treatment medium if suitable conditions are present. The processes of sorption, filtration and oxidation can remove the various wastewater pollutants. The subsurface characteristics of the disposal area are among the most important parameters governing process performance. Therefore it is important that the soil and topographic conditions are taken into consideration in the design of the soil absorption system. Seepage trenches and beds are the common systems in use. Seepage pits or chambers can be used where subsurface conditions warrant, whilst above grade mounds have been recommended for a variety of difficult site conditions. All these systems have their inherent advantages and disadvantages and the preferable soil absorption system should be selected based on site characteristics. The use of gravel as in-fill for beds and trenches is open to question. It does not contribute to effluent treatment and has been shown to reduce the effective infiltrative surface area. This is due to physical obstruction and the migration of fines entrained in the gravel, into the soil matrix. The surface application of effluent is coming into increasing use with the advent of aerobic treatment systems. This has the advantage that treatment is undertaken on the upper soil horizons, which is chemically and biologically the most effective in effluent renovation. Numerous research studies have demonstrated the feasibility of this practice. However the overriding criteria is the quality of the effluent. It has to be of exceptionally good quality in order to ensure that there are no resulting public health impacts due to aerosol drift. This essentially is the main issue of concern, due to the unreliability of the effluent quality from aerobic systems. Secondly, it has also been found that most householders do not take adequate care in the operation of spray irrigation systems or in the maintenance of the irrigation area. Under these circumstances surface disposal of effluent should be approached with caution and would require appropriate householder education and stringent compliance requirements. However despite all this, the efficiency with which the process is undertaken will ultimately rest with the individual householder and this is where most concern rests. Greywater too should require similar considerations. Surface irrigation of greywater is currently being permitted in a number of local authority jurisdictions in Queensland. Considering the fact that greywater constitutes the largest fraction of the total wastewater generated in a household, it could be considered to be a potential resource. Unfortunately in most circumstances the only pretreatment that is required to be undertaken prior to reuse is the removal of oil and grease. This is an issue of concern as greywater can considered to be a weak to medium sewage as it contains primary pollutants such as BOD material and nutrients and may also include microbial contamination. Therefore its use for surface irrigation can pose a potential health risk. This is further compounded by the fact that most householders are unaware of the potential adverse impacts of indiscriminate greywater reuse. As in the case of blackwater effluent reuse, there have been suggestions that greywater should also be subjected to stringent guidelines. Under these circumstances the surface application of any wastewater requires careful consideration. The other option available for the disposal effluent is the use of evaporation systems. The use of evapotranspiration systems has been covered in this report. Research has shown that these systems are susceptible to a number of factors and in particular to climatic conditions. As such their applicability is location specific. Also the design of systems based solely on evapotranspiration is questionable. In order to ensure more reliability, the systems should be designed to include soil absorption. The successful use of these systems for intermittent usage has been noted in literature. Taking into consideration the issues discussed above, subsurface disposal of effluent is the safest under most conditions. This is provided the facility has been designed to accommodate site conditions. The main problem associated with subsurface disposal is the formation of a clogging mat on the infiltrative surfaces. Due to the formation of the clogging mat, the capacity of the soil to handle effluent is no longer governed by the soil’s hydraulic conductivity as measured by the percolation test, but rather by the infiltration rate through the clogged zone. The characteristics of the clogging mat have been shown to be influenced by various soil and effluent characteristics. Secondly, the mechanisms of clogging mat formation have been found to be influenced by various physical, chemical and biological processes. Biological clogging is the most common process taking place and occurs due to bacterial growth or its by-products reducing the soil pore diameters. Biological clogging is generally associated with anaerobic conditions. The formation of the clogging mat provides significant benefits. It acts as an efficient filter for the removal of microorganisms. Also as the clogging mat increases the hydraulic impedance to flow, unsaturated flow conditions will occur below the mat. This permits greater contact between effluent and soil particles thereby enhancing the purification process. This is particularly important in the case of highly permeable soils. However the adverse impacts of the clogging mat formation cannot be ignored as they can lead to significant reduction in the infiltration rate. This in fact is the most common cause of soil absorption systems failure. As the formation of the clogging mat is inevitable, it is important to ensure that it does not impede effluent infiltration beyond tolerable limits. Various strategies have been investigated to either control clogging mat formation or to remediate its severity. Intermittent dosing of effluent is one such strategy that has attracted considerable attention. Research conclusions with regard to short duration time intervals are contradictory. It has been claimed that the intermittent rest periods would result in the aerobic decomposition of the clogging mat leading to a subsequent increase in the infiltration rate. Contrary to this, it has also been claimed that short duration rest periods are insufficient to completely decompose the clogging mat, and the intermediate by-products that form as a result of aerobic processes would in fact lead to even more severe clogging. It has been further recommended that the rest periods should be much longer and should be in the range of about six months. This entails the provision of a second and alternating seepage bed. The other concepts that have been investigated are the design of the bed to meet the equilibrium infiltration rate that would eventuate after clogging mat formation; improved geometry such as the use of seepage trenches instead of beds; serial instead of parallel effluent distribution and low pressure dosing of effluent. The use of physical measures such as oxidation with hydrogen peroxide and replacement of the infiltration surface have been shown to be only of short-term benefit. Another issue of importance is the degree of pretreatment that should be provided to the effluent prior to subsurface application and the influence exerted by pollutant loadings on the clogging mat formation. Laboratory studies have shown that the total mass loadings of BOD and suspended solids are important factors in the formation of the clogging mat. It has also been found that the nature of the suspended solids is also an important factor. The finer particles from extended aeration systems when compared to those from septic tanks will penetrate deeper into the soil and hence will ultimately cause a more dense clogging mat. However the importance of improved pretreatment in clogging mat formation may need to be qualified in view of other research studies. It has also shown that effluent quality may be a factor in the case of highly permeable soils but this may not be the case with fine structured soils. The ultimate test of onsite sewage treatment system efficiency rests with the final disposal of effluent. The implication of system failure as evidenced from the surface ponding of effluent or the seepage of contaminants into the groundwater can be very serious as it can lead to environmental and public health impacts. Significant microbial contamination of surface and groundwater has been attributed to septic tank effluent. There are a number of documented instances of septic tank related waterborne disease outbreaks affecting large numbers of people. In a recent incident, the local authority was found liable for an outbreak of viral hepatitis A and not the individual septic tank owners as no action had been taken to remedy septic tank failure. This illustrates the responsibility placed on local authorities in terms of ensuring the proper operation of onsite sewage treatment systems. Even a properly functioning soil absorption system is only capable of removing phosphorus and microorganisms. The nitrogen remaining after plant uptake will not be retained in the soil column, but will instead gradually seep into the groundwater as nitrate. Conditions for nitrogen removal by denitrification are not generally present in a soil absorption bed. Dilution by groundwater is the only treatment available for reducing the nitrogen concentration to specified levels. Therefore based on subsurface conditions, this essentially entails a maximum allowable concentration of septic tanks in a given area. Unfortunately nitrogen is not the only wastewater pollutant of concern. Relatively long survival times and travel distances have been noted for microorganisms originating from soil absorption systems. This is likely to happen if saturated conditions persist under the soil absorption bed or due to surface runoff of effluent as a result of system failure. Soils have a finite capacity for the removal of phosphorus. Once this capacity is exceeded, phosphorus too will seep into the groundwater. The relatively high mobility of phosphorus in sandy soils have been noted in the literature. These issues have serious implications in the design and siting of soil absorption systems. It is not only important to ensure that the system design is based on subsurface conditions but also the density of these systems in given areas is a critical issue. This essentially involves the adoption of a land capability approach to determine the limitations of an individual site for onsite sewage disposal. The most limiting factor at a particular site would determine the overall capability classification for that site which would also dictate the type of effluent disposal method to be adopted.

PALLAS : limiting indications for dronedarone treatment of atrial fibrillation.

Atrial fibrillation increases the risk of stroke. Dronedarone has been shown to reduce the composite of hospitalizations due to cardiovascular events or death, in subjects with intermittent atrial fibrillation or flutter. Recently, dronedarone has been tested in subjects with permanent atrial fibrillation in the PALLAS (permanent atrial fibrillation outcome study using dronedarone on top of standard therapy) trial, and this clinical trial is evaluated in this paper. PALLAS was stopped early as there was an increased incidence of cardiovascular events in the dronedarone group. Dronedarone also increased the rate of hospitalizations in PALLAS. As a result of PALLAS, dronedarone has been contraindicated in permanent atrial fibrillation. The outcomes of PALLAS highlight a discontinuity between dronedarone actions in permanent and intermittent atrial fibrillation. The mechanism(s) underlying the detrimental effects of dronedarone in permanent atrial fibrillation are unknown at present and need to be investigated.

Socioeconomic status and health outcomes in a developing country

Although the relationship between socioeconomic status (SES) and health is well documented for developed countries, less evidence has been presented for developing countries. The aim of this paper is to analyse this relationship at the household level for Fiji, a developing country in the South Pacific, using original household survey data. To allow for the endogeneity of SES status in the household health production function, we utilize a simultaneous equation approach where estimates are achieved by full information maximum likelihood. By restricting our sample to one, relatively small island, and including area and district hospital effects, physical geography effects are unpacked from income effects. We measure SES, as permanent income which is constructed using principal components analysis. An alternative specification considers transitory household income. We find that a 1% increase in wealth (our measure of permanent income) would lead to a 15% decrease in the probability of an incapacitating illness occurring intra-household. Although the presence of a strong relationship indicates that relatively small improvements in SES status can significantly improve health at the household level, it is argued that the design of appropriate policy would also require an understanding of the various mechanisms through which the relationship operates.

Participatory photography and self-empowerment in different nations

Volunteering Qld’s Project Creatives continues to explore the critical role creative disciplines and creative people play in providing new models of engagement and action in social change and community work. This article explores three different non-profit organisations that have used collaborative photography to enable locals to empower themselves. Written by Alice Baroni a volunteer with the Education, Research and Policy Unit of Volunteering Qld. Alice is undertaking a PhD at the Queensland University of Technology, exploring (photo) journalism, participatory content creation and community photography in Brazil’s low income suburbs. She is part of the ARC Centre of Excellence for Creative Industries and Innovation, and a Brazilian research group ‘Storytellers and Narratives: Contemporary Journalism’. Two of the initiatives explored in this publication are Viva Favela and Imagens do Povo that are ideologically and physically supported by, respectively, Viva Rio and Observatório de Favelas, based in Rio de Janeiro, Brazil. ‘Favela’ is often translated simply as ‘slum’ or ‘shantytown’, but these terms connote negative characteristics such as shortage, poverty, and deprivation, which end up stigmatising these low-income suburbs. Fotografi Senza Frontiere (FSF) (Photographers Without Borders) is an Italian non-governmental organisation that gathers together a group of photographers who aim to provide youth from extreme regions in Nicaragua, Algeria, Argentina, Panama, Uganda, and Palestine with skills to photograph and document their own reality by establishing permanent photo laboratories. This idea, which is similar to that of Viva Favela and Imagens do Povo, is to enable youth to become professional photographers as a means of self-representation and self-empowerment. Afterwards, students become educators in established photographic labs so as to pass on what they have learnt through FSF’s photographic courses.

Learning landscapes 2.0 : warning - assembly required

Twenty first century learners operate in organic, immersive environments. A pedagogy of student-centred learning is not a recipe for rooms. A contemporary learning environment is like a landscape that grows, morphs, and responds to the pressures of the context and micro-culture. There is no single adaptable solution, nor a suite of off-the-shelf answers; propositions must be customisable and infinitely variable. They must be indeterminate and changeable; based on the creation of learning places, not restrictive or constraining spaces. A sustainable solution will be un-fixed, responsive to the life cycle of the components and materials, able to be manipulated by the users; it will create and construct its own history. Learning occurs as formal education with situational knowledge structures, but also as informal learning, active learning, blended learning social learning, incidental learning, and unintended learning. These are not spatial concepts but socio-cultural patterns of discovery. Individual learning requirements must run free and need to be accommodated as the learner sees fit. The spatial solution must accommodate and enable a full array of learning situations. It is a system not an object. Three major components: 1. The determinate landscape: in-situ concrete 'plate' that is permanent. It predates the other components of the system and remains as a remnant/imprint/fossil after the other components of the system have been relocated. It is a functional learning landscape in its own right; enabling a variety of experiences and activities. 2. The indeterminate landscape: a kit of pre-fabricated 2-D panels assembled in a unique manner at each site to suit the client and context. Manufactured to the principles of design-for-disassembly. A symbiotic barnacle like system that attaches itself to the existing infrastructure through the determinate landscape which acts as a fast growth rhizome. A carapace of protective panels, infinitely variable to create enclosed, semi-enclosed, and open learning places. 3. The stations: pre-fabricated packages of highly-serviced space connected through the determinate landscape. Four main types of stations; wet-room learning centres, dry-room learning centres, ablutions, and low-impact building services. Entirely customised at the factory and delivered to site. The stations can be retro-fitted to suit a new context during relocation. Principles of design for disassembly: material principles • use recycled and recyclable materials • minimise the number of types of materials • no toxic materials • use lightweight materials • avoid secondary finishes • provide identification of material types component principles • minimise/standardise the number of types of components • use mechanical not chemical connections • design for use of common tools and equipment • provide easy access to all components • make component size to suite means of handling • provide built in means of handling • design to realistic tolerances • use a minimum number of connectors and a minimum number of types system principles • design for durability and repeated use • use prefabrication and mass production • provide spare components on site • sustain all assembly and material information

Seriously playful : the uses of networked spoof videos in China

This thesis examines online spoof videos in China. It shows the relationship between user-created content and change and how such videos are impacting on social memory. In the West, we are witnessing two outstanding trends in media. On the one hand, media are turning more "demotic" (Turner, 2006) and "participatory" (Jenkins, 2006), whereby lay audiences use popular media for identity formation, representation and association, reconfiguring the media and cultural landscape, and rendering invalid the old paradigm based on the dichotomy of audience and author, creator and consumer, expert and amateur. On the other hand, in both mainstream media and user-creation online there is a trend towards "silly citizenship", with comedy, send-ups and spoofs that used to reside in the margin propelled to the central stage in both pleasure and politics (Hartley, 2010), as is shown in the rising popularity of the Daily Show, Colbert Report, and spoof videos in elections ,e.g. the 2008 presidential election in US (Gray, Jones, & Thompson, 2009; Tryon, 2008). User generated content—and spoof subcultures—is now much a debated phenomenon in China. However, with different political (one party rule and censorship) and cultural (media regarded mainly as instrument for education and social stabilization instead of a critical fourth estate) configurations, will the social and cultural impacts of the two trends in the West be as the same in China? If not, what will be the specificities in the China context? The project starts with a historical review of popular culture and user-created content in China, before turning to spoof videos and looking at how they are produced and shared, travel and diffused on the Internet, and how the communities and sub-cultures forming and emerging around spoof videos are changing the overall cultural landscape in China. By acting as a participant observer in online video sharing sites and conducting face-to face as well as online interviews, I identify lead users and creators of spoof videos and the social networks emerging around them. I call these lead users "skill hubs" and their networks "liquid communities", foregrounding the fact that their appeal doesn’t come from their amicable personality, but rather from their creative skills; and that the networks surrounding them are in a permanent flux, with members coming and going as they see fit. I argue that the "liquidness" (Bauman, 2000) of these communities is what makes them constantly creative and appealing. Textual analysis of online videos, their comments and derivatives are conducted to tease out the uses that that can be made of spoof videos, namely as phatic communication, as alternative memory and as political engagement. Through these analyses I show that spoof videos constitute not only a space where young generations can engage with each other, communicate their anger and dissatisfaction, fun and hope, and where they participate in socio-cultural and political debates, but also create a space where they can experiment with their new skills, new ideas, and new citizenship. The rise of spoof videos heralds the beginning of a trend in popular culture in contemporary China towards the "canonization of the jester" and the dethroning of the establishment. I also argue that a historical perspective is needed to understand the current surge of use creativity and user activism in China, and that many forms of popular media we experience today have their antecedents in various stages of Chinese history. The entrenched "control-resistance" binary is inadequate in interpreting the rich, flux and multilayered Internet space in China.

Communicating in the pre-hospital emergency environment

Aim. To develop and evaluate the implementation of a communication board for paramedics to use with patients as an augmentative or alternative communication tool to address communication needs of patients in the pre-hospital setting. Method. A double-sided A4-size communication board was designed specifically for use in the pre-hospital setting by the Queensland Ambulance Service and Disability and Community Care Services. One side of the board contains expressive messages that could be used by both the patient and paramedic. The other side contains messages to support patients’ understanding and interaction tips for the paramedic. The communication board was made available in every ambulance and patient transport vehicle in the Brisbane Region. Results. A total of 878 paramedics completed a survey that gauged which patient groups they might use the communication board with. The two most common groups were patients from culturally and linguistically diverse backgrounds and children. Staff reported feeling confident in using the board, and 72% of interviewed paramedics agreed that the communication board was useful for aiding communication with patients. Feedback from paramedics suggests that the board is simple to use, reduces patient frustration and improves communication. Conclusion. These results suggest that a communication board can be applied in the pre-hospital setting to support communication success with patients. What is known about the topic? It is imperative that communication between patient and paramedic is clear and effective. Research has shown that communication boards have been effective with people with temporary or permanent communication difficulties. What does this paper add? This is the first paper outlining the development and use of a communication board by paramedics in the pre-hospital setting in Australia. The paper details the design of the communication board for the unique pre-hospital environment. The paper provides some preliminary data on the use of the communication board with certain patient groups and its effectiveness as an alternative communication tool. What are the implications for practitioners? The findings support the use of the tool as a viable option in supporting the communication between paramedics and a range of patients. It is not suggested that this communication board will meet the complete communication needs of any individual in this environment, but it is hoped that the board’s presence within the Queensland Ambulance Service may result in paramedics introducing the board on occasions where communication with a patient is challenging.