A suitable method for journal bearing wear measurement

Purpose – Ideally, there is no wear in hydrodynamic lubrication regime. A small amount of wear occurs during start and stop of the machines and the amount of wear is so small that it is difficult to measure with accuracy. Various wear measuring techniques have been used where out-of-roundness was found to be the most reliable method of measuring small wear quantities in journal bearings. This technique was further developed to achieve higher accuracy in measuring small wear quantities. The method proved to be reliable as well as inexpensive. The paper aims to discuss these issues. Design/methodology/approach – In an experimental study, the effect of antiwear additives was studied on journal bearings lubricated with oil containing solid contaminants. The test duration was too long and the wear quantities achieved were too small. To minimise the test duration, short tests of about 90 min duration were conducted and wear was measured recording changes in variety of parameters related to weight, geometry and wear debris. The out-of-roundness was found to be the most effective method. This method was further refined by enlarging the out-of-roundness traces on a photocopier. The method was proved to be reliable and inexpensive. Findings – Study revealed that the most commonly used wear measurement techniques such as weight loss, roughness changes and change in particle count were not adequate for measuring small wear quantities in journal bearings. Out-of-roundness method with some refinements was found to be one of the most reliable methods for measuring small wear quantities in journal bearings working in hydrodynamic lubrication regime. By enlarging the out-of-roundness traces and determining the worn area of the bearing cross-section, weight loss in bearings was calculated, which was repeatable and reliable. Research limitations/implications – This research is a basic in nature where a rudimentary solution has been developed for measuring small wear quantities in rotary devices such as journal bearings. The method requires enlarging traces on a photocopier and determining the shape of the worn area on an out-of-roundness trace on a transparency, which is a simple but a crude method. This may require an automated procedure to determine the weight loss from the out-of-roundness traces directly. This method can be very useful in reducing test duration and measuring wear quantities with higher precision in situations where wear quantities are very small. Practical implications – This research provides a reliable method of measuring wear of circular geometry. The Talyrond equipment used for measuring the change in out-of-roundness due to wear of bearings indicates that this equipment has high potential to be used as a wear measuring device also. Measurement of weight loss from the traces is an enhanced capability of this equipment and this research may lead to the development of a modified version of Talyrond type of equipment for wear measurements in circular machine components. Originality/value – Wear measurement in hydrodynamic bearings requires long duration tests to achieve adequate wear quantities. Out-of-roundness is one of the geometrical parameters that changes with progression of wear in a circular shape components. Thus, out-of-roundness is found to be an effective wear measuring parameter that relates to change in geometry. Method of increasing the sensitivity and enlargement of out-of-roundness traces is original work through which area of worn cross-section can be determined and weight loss can be derived for materials of known density with higher precision.

FlexAnalytics: A flexible data analytics framework for big data applications with I/O performance improvement

Increasingly larger scale applications are generating an unprecedented amount of data. However, the increasing gap between computation and I/O capacity on High End Computing machines makes a severe bottleneck for data analysis. Instead of moving data from its source to the output storage, in-situ analytics processes output data while simulations are running. However, in-situ data analysis incurs much more computing resource contentions with simulations. Such contentions severely damage the performance of simulation on HPE. Since different data processing strategies have different impact on performance and cost, there is a consequent need for flexibility in the location of data analytics. In this paper, we explore and analyze several potential data-analytics placement strategies along the I/O path. To find out the best strategy to reduce data movement in given situation, we propose a flexible data analytics (FlexAnalytics) framework in this paper. Based on this framework, a FlexAnalytics prototype system is developed for analytics placement. FlexAnalytics system enhances the scalability and flexibility of current I/O stack on HEC platforms and is useful for data pre-processing, runtime data analysis and visualization, as well as for large-scale data transfer. Two use cases – scientific data compression and remote visualization – have been applied in the study to verify the performance of FlexAnalytics. Experimental results demonstrate that FlexAnalytics framework increases data transition bandwidth and improves the application end-to-end transfer performance.

Combining HPLC-DAD and ICP-MS data for improved analysis of complex samples: Classification of the root samples from Cortex moutan

A combined data matrix consisting of high performance liquid chromatography–diode array detector (HPLC–DAD) and inductively coupled plasma-mass spectrometry (ICP-MS) measurements of samples from the plant roots of the Cortex moutan (CM), produced much better classification and prediction results in comparison with those obtained from either of the individual data sets. The HPLC peaks (organic components) of the CM samples, and the ICP-MS measurements (trace metal elements) were investigated with the use of principal component analysis (PCA) and the linear discriminant analysis (LDA) methods of data analysis; essentially, qualitative results suggested that discrimination of the CM samples from three different provinces was possible with the combined matrix producing best results. Another three methods, K-nearest neighbor (KNN), back-propagation artificial neural network (BP-ANN) and least squares support vector machines (LS-SVM) were applied for the classification and prediction of the samples. Again, the combined data matrix analyzed by the KNN method produced best results (100% correct; prediction set data). Additionally, multiple linear regression (MLR) was utilized to explore any relationship between the organic constituents and the metal elements of the CM samples; the extracted linear regression equations showed that the essential metals as well as some metallic pollutants were related to the organic compounds on the basis of their concentrations

A CCG virtual system for big data application communication costs analysis

Network topology and routing are two important factors in determining the communication costs of big data applications at large scale. As for a given Cluster, Cloud, or Grid system, the network topology is fixed and static or dynamic routing protocols are preinstalled to direct the network traffic. Users cannot change them once the system is deployed. Hence, it is hard for application developers to identify the optimal network topology and routing algorithm for their applications with distinct communication patterns. In this study, we design a CCG virtual system (CCGVS), which first uses container-based virtualization to allow users to create a farm of lightweight virtual machines on a single host. Then, it uses software-defined networking (SDN) technique to control the network traffic among these virtual machines. Users can change the network topology and control the network traffic programmingly, thereby enabling application developers to evaluate their applications on the same system with different network topologies and routing algorithms. The preliminary experimental results through both synthetic big data programs and NPB benchmarks have shown that CCGVS can represent application performance variations caused by network topology and routing algorithm.

A novel near-infrared spectroscopy and chemometrics method for rapid analysis of several chemical components and antioxidant activity of mint (mentha haplocalyx briq.) samples

A novel near-infrared spectroscopy (NIRS) method has been researched and developed for the simultaneous analyses of the chemical components and associated properties of mint (Mentha haplocalyx Briq.) tea samples. The common analytes were: total polysaccharide content, total flavonoid content, total phenolic content, and total antioxidant activity. To resolve the NIRS data matrix for such analyses, least squares support vector machines was found to be the best chemometrics method for prediction, although it was closely followed by the radial basis function/partial least squares model. Interestingly, the commonly used partial least squares was unsatisfactory in this case. Additionally, principal component analysis and hierarchical cluster analysis were able to distinguish the mint samples according to their four geographical provinces of origin, and this was further facilitated with the use of the chemometrics classification methods-K-nearest neighbors, linear discriminant analysis, and partial least squares discriminant analysis. In general, given the potential savings with sampling and analysis time as well as with the costs of special analytical reagents required for the standard individual methods, NIRS offered a very attractive alternative for the simultaneous analysis of mint samples.

Situated interfaces for engaging citizens on the go

Insights Live screening and playfulness of the interactive space can be effective strategies for attracting the attention of passers-by and turn them into active participants. While urban screen interfaces increase participation by encouraging group interaction, privately-oriented tangible user interfaces give people a longer time to reflect upon their answers.

Evidence-based recommendations for the diagnosis of ankylosing spondylitis: Results from the Australian 3E initiative in rheumatology

• As part of the 3E program, we conducted a systematic literature review and gathered consensus from 23 practising Australian rheumatologists to develop guidelines for early identification of ankylosing spondylitis and specialist referral. • In three rounds of break-out sessions followed by discussion and voting, the specialist panel addressed three questions related to diagnosis of ankylosing spondylitis: In individuals with back pain, what are the early clinical features that suggest ankylosing spondylitis? How useful is imaging in identifying early ankylosing spondylitis? Based on which clinical features should a general practitioner refer a patient to a rheumatologist for further evaluation? • The panel agreed on six recommendations related to the three questions: 1a. Early clinical features to suggest ankylosing spondylitis include inflammatory back pain and age at symptom onset < 45 years. 1b. The absence of symptomatic response to an appropriate course of non-steroidal anti-inflammatory drugs makes the diagnosis of ankylosing spondylitis less likely. 1c. Raised inflammatory markers are supportive, but their absence does not rule out the diagnosis of ankylosing spondylitis. 2a. Despite low sensitivity to detect changes of early ankylosing spondylitis, plain radiographs of the pelvis and spine are appropriate initial imaging techniques. 2b. Magnetic resonance imaging is a useful imaging modality for detecting early changes of ankylosing spondylitis. 3. Individuals with inflammatory back pain should be referred to a rheumatologist for further evaluation. • Effective dissemination and implementation of these recommendations are important to standardise the approach to early diagnosis of ankylosing spondylitis.

Evidence-based recommendations for the monitoring and treatment of ankylosing spondylitis: Results from the Australian 3E initiative in rheumatology

Aim: To develop a set of Australian recommendations for the monitoring and treatment of ankylosing spondylitis (AS) through systematic literature review combined with the opinion of practicing rheumatologists. Methods: A set of eight questions, four in each domain of monitoring and treatment, were formulated by voting and the Delphi method. The results of a systematic literature review addressing each question were presented to the 23 participants of the Australian 3E meeting. All participants were clinical rheumatologists experienced in the daily management of AS. Results: After three rounds of breakout sessions to discuss the findings of the literature review, a set of recommendations was finalized after discussion and voting. The category of evidence and strength of recommendation were determined for each proposal. The level of agreement among participants was excellent (mean 84%, range 64-100%). Conclusions: The 12 recommendations developed from evidence and expert opinion provide guidance for the daily management of AS patients. For most recommendations, we found a paucity of supportive evidence in the literature highlighting the need for additional clinical studies.

Acoustic features for multi-level classification of Australian frogs

Over past few decades, frog species have been experiencing dramatic decline around the world. The reason for this decline includes habitat loss, invasive species, climate change and so on. To better know the status of frog species, classifying frogs has become increasingly important. In this study, acoustic features are investigated for multi-level classification of Australian frogs: family, genus and species, including three families, eleven genera and eighty five species which are collected from Queensland, Australia. For each frog species, six instances are selected from which ten acoustic features are calculated. Then, the multicollinearity between ten features are studied for selecting non-correlated features for subsequent analysis. A decision tree (DT) classifier is used to visually and explicitly determine which acoustic features are relatively important for classifying family, which for genus, and which for species. Finally, a weighted support vector machines (SVMs) classifier is used for the multi- level classification with three most important acoustic features respectively. Our experiment results indicate that using different acoustic feature sets can successfully classify frogs at different levels and the average classification accuracy can be up to 85.6%, 86.1% and 56.2% for family, genus and species respectively.

Social media in selected Australian federal and state election campaigns, 2010-15

Campaigning in Australian election campaigns at local, state, and federal levels is fundamentally affected by the fact that voting is compulsory in Australia, with citizens who are found to have failed to cast their vote subject to fines. This means that - contrary to the situation in most other nations – elections are decided not by which candidate or party has managed to encourage the largest number of nominal supporters to make the effort to cast their vote, but by some 10-20% of genuine ‘swinging voters’ who change their party preferences from one election to the next. Political campaigning is thus aimed less at existing party supporters (so-called ‘rusted on’ voters whose continued support for the party is essentially taken for granted) than at this genuinely undecided middle of the electorate. Over the past decades, this has resulted in a comparatively timid, vague campaigning style from both major party blocs (the progressive Australian Labor Party [ALP] and the conservative Coalition of the Liberal and National Parties [L/NP]). Election commitments that run the risk of being seen as too partisan and ideological are avoided as they could scare away swinging voters, and recent elections have been fought as much (or more) on the basis of party leaders’ perceived personas as they have on stated policies, even though Australia uses a parliamentary system in which the Prime Minister and state Premiers are elected by their party room rather than directly by voters. At the same time, this perceived lack of distinctiveness in policies between the major parties has also enabled the emergence of new, smaller parties which (under Australia’s Westminster-derived political system) have no hope of gaining a parliamentary majority but could, in a close election, come to hold the balance of power and thus exert disproportionate influence on a government which relies on their support.

Considering gambling involvement in the understanding of problem gambling: A large cross-sectional study of an Australian population

Instead of regarding a particular type of gambling activity (for example, electronic gambling machines, table games) as an isolated factor for problem gambling, recent research suggests that gambling involvement (for example, as measured by the number of different types of gambling activities played) should also be considered. Using a large sample of the Victorian adult population, this study found that the strength of association between problem gambling and the type of gambling reduced after adjusting for gambling involvement. This finding supports recent research that gambling involvement is an important factor in assessing the risk of problem gambling. The study also provides insights into the measurements of gambling involvement and provides alternative statistical modelling to analyse problem gambling.

Private mobile phones and public communication drums in rural Papua New Guinea

The voice of a traditional communication drum can be heard over great distances. Yet now in Papua New Guinea (PNG) it is hearing, by phone, the voice of a loved one who has moved far away from home for work, marriage or studies that brings the greatest delight. As recently as 2007, most areas of this Pacific island nation had no form of telephony available. Apart from radio, modern communication forms have been restricted predominantly to the urban areas where only a small percentage of the people reside. Landline telephones, television, Internet, facsimile machines and so on have never reached the majority of the inhabited areas...

Inventing the Future: Intellectual Property and 3D Printing

A new technology – 3D printing – has the potential to make radical changes to aspects of the way in which we live. Put simply, it allows people to download designs and turn them into physical objects by laying down successive layers of material. Replacements or parts for household objects such as toys, utensils and gadgets could become available at the press of a button. With this innovation, however, comes the need to consider impacts on a wide range of forms of intellectual property, as Dr Matthew Rimmer explains. 3D Printing is the latest in a long line of disruptive technologies – including photocopiers, cassette recorders, MP3 players, personal computers, peer to peer networks, and wikis – which have challenged intellectual property laws, policies, practices, and norms. As The Economist has observed, ‘Tinkerers with machines that turn binary digits into molecules are pioneering a whole new way of making things—one that could well rewrite the rules of manufacturing in much the same way as the PC trashed the traditional world of computing.’

Activity recognition using binary tree SVM

This paper presents an effective classification method based on Support Vector Machines (SVM) in the context of activity recognition. Local features that capture both spatial and temporal information in activity videos have made significant progress recently. Efficient and effective features, feature representation and classification plays a crucial role in activity recognition. For classification, SVMs are popularly used because of their simplicity and efficiency; however the common multi-class SVM approaches applied suffer from limitations including having easily confused classes and been computationally inefficient. We propose using a binary tree SVM to address the shortcomings of multi-class SVMs in activity recognition. We proposed constructing a binary tree using Gaussian Mixture Models (GMM), where activities are repeatedly allocated to subnodes until every new created node contains only one activity. Then, for each internal node a separate SVM is learned to classify activities, which significantly reduces the training time and increases the speed of testing compared to popular the `one-against-the-rest' multi-class SVM classifier. Experiments carried out on the challenging and complex Hollywood dataset demonstrates comparable performance over the baseline bag-of-features method.

Design challenges for electronic medication administration record systems in residential aged care facilities: A formative evaluation

Introduction Electronic medication administration record (eMAR) systems are promoted as a potential intervention to enhance medication safety in residential aged care facilities (RACFs). The purpose of this study was to conduct an in-practice evaluation of an eMAR being piloted in one Australian RACF before its roll out, and to provide recommendations for system improvements. Methods A multidisciplinary team conducted direct observations of workflow (n=34 hours) in the RACF site and the community pharmacy. Semi-structured interviews (n=5) with RACF staff and the community pharmacist were conducted to investigate their views of the eMAR system. Data were analysed using a grounded theory approach to identify challenges associated with the design of the eMAR system. Results The current eMAR system does not offer an end-to-end solution for medication management. Many steps, including prescribing by doctors and communication with the community pharmacist, are still performed manually using paper charts and fax machines. Five major challenges associated with the design of eMAR system were identified: limited interactivity; inadequate flexibility; problems related to information layout and semantics; the lack of relevant decision support; and system maintenance issues.We suggest recommendations to improve the design of the eMAR system and to optimize existing workflows. Discussion Immediate value can be achieved by improving the system interactivity, reducing inconsistencies in data entry design and offering dedicated organisational support to minimise connectivity issues. Longer-term benefits can be achieved by adding decision support features and establishing system interoperability requirements with stakeholder groups (e.g. community pharmacies) prior to system roll out. In-practice evaluations of technologies like eMAR system have great value in identifying design weaknesses which inhibit optimal system use.