Studies on design, fabrication and reliability assessment of embedded passives on a high-density interconnect (HDI) organic substrate using a sequential build-up process

One of the foremost design considerations in microelectronics miniaturization is the use of embedded passives which provide practical solution. In a typical circuit, over 80 percent of the electronic components are passives such as resistors, inductors, and capacitors that could take up to almost 50 percent of the entire printed circuit board area. By integrating passive components within the substrate instead of being on the surface, embedded passives reduce the system real estate, eliminate the need for discrete and assembly, enhance electrical performance and reliability, and potentially reduce the overall cost. Moreover, it is lead free. Even with these advantages, embedded passive technology is at a relatively immature stage and more characterization and optimization are needed for practical applications leading to its commercialization.This paper presents an entire process from design and fabrication to electrical characterization and reliability test of embedded passives on multilayered microvia organic substrate. Two test vehicles focusing on resistors and capacitors have been designed and fabricated. Embedded capacitors in this study are made with polymer/ceramic nanocomposite (BaTiO3) material to take advantage of low processing temperature of polymers and relatively high dielectric constant of ceramics and the values of these capacitors range from 50 pF to 1.5 nF with capacitance per area of approximately 1.5 nF/cm(2). Limited high frequency measurement of these capacitors was performed. Furthermore, reliability assessments of thermal shock and temperature humidity tests based on JEDEC standards were carried out. Resistors used in this work have been of three types: 1) carbon ink based polymer thick film (PTF), 2) resistor foils with known sheet resistivities which are laminated to printed wiring board (PWB) during a sequential build-up (SBU) process and 3) thin-film resistor plating by electroless method. Realization of embedded resistors on conventional board-level high-loss epoxy (similar to 0.015 at 1 GHz) and proposed low-loss BCB dielectric (similar to 0.0008 at > 40 GHz) has been explored in this study. Ni-P and Ni-W-P alloys were plated using conventional electroless plating, and NiCr and NiCrAlSi foils were used for the foil transfer process. For the first time, Benzocyclobutene (BCB) has been proposed as a board level dielectric for advanced System-on-Package (SOP) module primarily due to its attractive low-loss (for RF application) and thin film (for high density wiring) properties.Although embedded passives are more reliable by eliminating solder joint interconnects, they also introduce other concerns such as cracks, delamination and component instability. More layers may be needed to accommodate the embedded passives, and various materials within the substrate may cause significant thermo -mechanical stress due to coefficient of thermal expansion (CTE) mismatch. In this work, numerical models of embedded capacitors have been developed to qualitatively examine the effects of process conditions and electrical performance due to thermo-mechanical deformations.Also, a prototype working product with the board level design including features of embedded resistors and capacitors are underway. Preliminary results of these are presented.

Increasing ionic conductivity of polymer-sodium salt complex by addition of a non-ionic plastic crystal

Ionic conductivity and other physico-chemical properties of a soft matter composite electrolyte comprising of a polymer-sodium salt complex and a non-ionic plastic crystal are discussed here. The electrolyte under discussion comprises of polyethyleneoxide (PEO)-sodium triflate (NaCF3SO3) and succinonitrile (SN). Addition of SN to PEO-NaCF3SO3 resulted in significant enhancement in ionic conductivity. At 50% SN concentration (with respect to weight of polymer), the polymer-plastic composite electrolyte room temperature (= 25 degrees C) ionic conductivity was similar to 1.1 x 10(-4) Omega(-1) cm(-1), approximately 45 times higher than PEO-NaCF3SO3. Observations from ac-impedance spectroscopy along with X-ray diffraction, differential scanning calorimetry and Fourier transform inrared spectroscopy strongly suggest the enhancement in the composite is ionicconductivity due to enhanced ion mobility via decrease in crystallinity of PEO. The free standing composite polymer-plastic electrolytes were more compliable than PEO-NaCF3SO3 thus exhibiting no detrimental effects of succinonitrile addition on the mechanical stability of PEO-NaCF3SO3. We propose that the exploratory PEO-NaCF3SO3-SN system.discussed here will eventually be developed as a prototype electrolyte.for sodium-sulfur batteries capable of operating at ambient and.sub-ambient conditions. (C) 2010 Elsevier B.V. All rights reserved.

Phase diagram and dielectric studies of binary organic materials

The phase equilibrium studies of organic system, involving resorcinol (R) and p-dimethylaminobenzaldehyde (DMAB), reveal the formation of a 1:1 molecular complex with two eutectics. The heat of mixing, entropy of fusion, roughness parameter, interfacial energy, and the excess thermodynamic functions were calculated based on enthalpy of fusion data determined via differential scanning calorimetric (DSC) method. X-ray powder diffraction studies confirm that the eutectics are not simple mechanical mixture of the components under investigation. The spectroscopic investigations (IR and NMR) suggest the occurrence of hydrogen bonding between the components forming the molecular complex. The dielectric measurements, carried out on hot-pressed addition compound (molecular complex), show higher dielectric constant at 320 K than that of individual components. The microstructural investigations of eutectic and addition compound indicate dendritic and faceted morphological features. (C) 2000 Elsevier Science B.V. All rights reserved.

Selective para metalation of unprotected 3-methoxy and 3,5-dimethoxy benzoic acids with n-butyl lithium-potassium tert-butoxide (LIC-KOR): synthesis of 3,5-dimethoxy-4-methyl benzoic acid

The potassium salt of 3-methoxy and 3,5-dimethoxy benzoic acids undergoes deprotonation at the position para to the carboxylate group selectively when treated with LIC-KOR in THF at -78 degrees C and it has been extended to the synthesis of 3,5-dimethoxy-4-methyl benzoic acid. (C) 2000 Elsevier Science Ltd. All rights reserved.

Charge Density Analysis of Crystals of Nicotinamide with Salicylic Acid and Oxalic Acid: An Insight into the Salt to Cocrystal Continuum

Charge density analysis from both experimental and theoretical points of view on two molecular complexes: one is formed between nicotinamide and salicylic acid, and the other formed between nicotinamide and oxalic acid brings out the quantitative topological features to distinguish a cocrystal from a salt.

Effects of electron correlations in conjugated organic molecules and solids

The discrepancies between the non-interacting models and experimental results for conjugated systems is highlighted in this brief review. The interacting model hamiltonians correctly give the forbidden singlet state below the optical gap in polyenes and also explain both the nonvanishing optical gap in polyacetylenes and the vanishing optical gap in symmetric cyanine dyes. The negative spin densities in polyene radicals is also understood in terms of a correlated picture. The role of electron-electron interactions in other strongly correlated systems, such as polydiacetylene and mixed and segregated stack charge transfer solids, are also briefly discussed.

Numerically Exact Study of Polarizabilities and Hyperpolarizabilities of Correlated Conjugated Organic Models

Polarizabilities and Hyperpolarizabilities of conjugated organic chains are calculated using correlated model Hamiltonians. While correlations reduce the Polarizabilities and extend the range of linear response, the Hyperpolarizabilities essentially are unaffected by the same. This explains the apparently large Hyperpolarizabilities of conjugated electronic systems.

Contribution of sea-salt to aerosol optical depth over the Arabian Sea derived from MODIS observations

Making use of aerosol optical depths (AOD) derived from MODIS (onboard TERRA satellite) and winds from NCEP, and the fact that sea-salt optical depth over ocean is determined primarily by sea-surface wind speed, we examine the contribution of sea-salt to the composite aerosol optical depth ( AOD) over Arabian Sea ( AS), by developing empirical models for characterizing wind-speed dependence of sea-salt optical depth. We show that at high wind speeds, sea-salt contributes 81% to the coarse mode and 42% to the composite AOD in the southern AS. In contrast to this, over the northern AS, share of sea-salt to coarse mode and composite optical depth is only 35% and 16% respectively. Comparison of the sea-salt optical depth and coarse mode optical depth ( MODIS) showed excellent agreement. The sea-salt optical depth over AS at moderate to high wind speed is comparable to the anthropogenic AOD reported for this region during winter.

Non-carboxylate based metal-organic frameworks (MOFs) and related aspects

The metal-organic frameworks, in recent years, show a variety of new developments that includes new methods of preparation, post synthesis modifications and novel class of compounds. Though most of the developments happened in the carboxylate based family of compounds, the other related systems are also equally interesting. In this article,we have highlighted some of the developments that have taken place in the family of non-carboxylate metal-organic frameworks. We have also highlighted some of the recent attempts at modifying the surfaces and pores of the MOFs by careful chemical manipulations. (C) 2009 Elsevier Ltd. All rights reserved.

Crystal and molecular structure of the ammonium salt of the dinucleoside monophosphate d(CpG)

The crystal and molecular structure of the ammonium salt of deoxycytidylyl-(3'-5')-deoxyguanosine has been determined from 0.85 A resolution single crystal X-ray diffraction data. The crystals obtained by acetone diffusion technique at -20 degrees C, are orthorhombic, P212121, a = 12.880(2), b = 17444(2) and c = 27.642(2) A. The structure was solved by high resolution Patterson and Fourier methods and refined to R = 0.136. There are two d(CpG) molecules in the asymmetric unit forming a mini left handed Z-DNA helix. This is in contrast to the earlier reported forms of d(CpG) where the molecules form self base paired duplexes. There are two ammonium ions in the asymmetric unit. The major groove NH+4 ion interacts with N7 of guanines through water bridges besides making H-bonded interactions directly with the phosphate oxygen atoms. A second NH+4 ion is found in the minor groove interacting directly with the phosphate oxygen atoms. Symmetry related molecules pack in such a way that the cytosine base stacks on cytosine and guanine base on guanine. Our structure demonstrates that alternating d(CpG) sequences have the ability to adopt the left handed Z-DNA structure even at the dimer level i.e., in a sequence which is only two base pairs long.

In situ surface modification of molybdenum-doped organic-inorganic hybrid TiO2 nanoparticles under hydrothermal conditions and treatment of pharmaceutical effluent

Molybdenum-doped TiO2 organic-inorganic hybrid nanoparticles were synthesized under mild hydrothermal conditions by in situ surface modification using n-butylamine. This was carried out at 150 degrees C at autogeneous pressure over 18 h. n-Butylamine was selected as a surfactant since it produced nanoparticles of the desired size and shape. The products were characterized using powder X-ray diffraction, Fourier transform infrared spectrometry, dynamic light-scattering spectroscopy, UV-Vis spectroscopy and transmission electron microscopy. Chemical oxygen demand was estimated in order to determine the photodegradation efficiency of the molybdenum-doped TiO2 hybrid nanoparticles in the treatment of pharmaceutical effluents. It was found that molybdenum-doped TiO2 hybrid nanoparticles showed higher photocatalytic efficiency than untreated TiO2 nanoparticles.

A bifunctional approach towards the mild oxidation of organic halides: 2-dimethylamino-N,N-dimethylaniline N-oxide

The titled reagent incorporates an oxygen-centred nucleophile and a basic moiety�in a suitably mutual orientation�in the same molecule. It oxidises various primary benzylic bromides to the corresponding aromatic aldehydes under relatively mild conditions (MeCN/rt�50°C/6�24 h) in high yields (83�97%), and is thus a useful alternative to the Kornblum procedure.

A fluorescent probe study of the solubilisation of cholesterol by biie salt-phospholipid micelles

The fluorescent probe dansyl cadaverine has been shown to bind strongly to mixed bile salt-phospholipid micelles containing unsaturation in the fatty acyl chains. Incorporation of cholesterol into the mixed micelles reduces the number of molecules of bound dansyl cadaverine without altering the binding affinity. These results suggest a tighter packing of the hydrocarbon matrix of the micelles in the presence of cholesterol.