Low cycle fatigue behaviour of a low interstitial Ni-base superalloy

The low cycle fatigue behaviour of precipitation strengthened nickel-base superalloy 720Li containing a low concentration of interstitial carbon and boron was studied at 25, 400 and 650 degrees C. Cyclic stress response at all temperatures was stable under fully reversed constant total strain amplitude (Delta epsilon/2) when Delta epsilon/2 <= 0.6%. At Delta epsilon/2 > 0.6%, cyclic hardening was followed by softening, until fracture at 25 and 650 degrees C. At 400 degrees C, however, cyclic stress plateaued after initial hardening. Dislocation-dislocation interactions and precipitate shearing were the micromechanisms responsible for the cyclic hardening and softening, respectively. The number of reversals to failure vs. plastic strain amplitude plot exhibits a bilinear Coffin-Manson relation. Transmission electron microscopy substructures revealed that planar slip was the major deformation mode under the conditions examined. However, differences in its distribution were observed to be the cause for the bilinearity in fatigue lives. The presence of fine deformation twins at low Delta epsilon/2 at 650 degrees C suggests the role of twinning in homogenization of cyclic deformation.

EUF-analysis of tea soils of Southern India and tea productivity

The relationship between EUF extractable nutrients and conventional soil test extractable nutrients in the acid soils of Southern India on one hand and that between EUF values and tea productivity on the other are described. Close correlation exists between EUF-NO3–N at 20°C and CuSO4–Ag2SO4-extractable NO3–N (r=0.98***), EUF-Norg and Morgan's reagent extractable NH4–N (r=0.97***), total EUF-N and CuSO4–Ag2SO4-extractable NO3–N plus Morgan's reagent NH4–N (r=0.96***), EUF-P at 20°C and modified Bray II-P (r=0.93***) and EUF-P at 20°C plus that at 80°C and modified Bray II-P (r=0.91***). The EUF-K at 20°C shows close correlation with NH4OAc–K (r=0.80***), Ag-thiourea-K (r=0.86***) and Morgan's reagent-K (r=0.84***) whereas the EUF-K at 80°C shows close correlation with the difference in K contents of NH4OAc–K and Ag-thiourea-K (r=0.92***) or of NH4OAc–K and Morgan's reagent-K (r=0.93***) and fixed NH4–N (r=0.89***). EUF-Ca, EUF-Mg and EUF-Mn do not show any relationship with conventional soil test values. Tea productivity is strongly associated with EUF-N and EUF-P extracted at 20°C.

Deflection analysis of hybrid laminated composite plates

In this paper an attempt is made to obtain deflections of hybrid, laminated, rectangular and skew composite plates. Analysis is performed by employing the Galerkin technique. Numerical results have been obtained for two types of layups employing Kevlar/epoxy and Boron/epoxy laminae. It is observed that for a given aspect ratio the rigidity of the skew plate increases with an increase in the skew angle. Further, for a specified deflection, the hybrid laminates turn out to be lighter.

BCN:A Graphene Analogue with Remarkable Adsorptive Properties

A new analogue of graphene containing boron, carbon and nitrogen (BCN) has been obtained by the reaction of high-surface-area activated charcoal with a mixture of boric acid and urea at 900 degrees C. X-ray photoelectron spectroscopy and electron energy-loss spectroscopy reveal the composition to be close to BCN. The X-ray diffraction pattern, high-resolution electron microscopy images and Raman spectrum indicate the presence of graphite-type layers with low sheet-to-sheet registry. Atomic force microscopy reveals the sample to consist of two to three layers of BCN, as in a few-layer graphene. BCN exhibits more electrical resistivity than graphene, but weaker magnetic features. BCN exhibits a surface area of 2911 m(2)g(-1), which is the highest value known for a BxCyNz composition. It exhibits high propensity for adsorbing CO2 (approximate to 100 wt %) at 195 K and a hydrogen uptake of 2.6 wt % at 77 K. A first-principles pseudopotential-based DFT study shows the stable structure to consist of BN3 and NB3 motifs. The calculations also suggest the strongest CO2 adsorption to occur with a binding energy of 3.7 kJ mol(-1) compared with 2.0 kJ mol(-1) on graphene.

Electronic Structure and Bonding in Neutral and Dianionic Boradiphospholes: R ' BC2P2R2 (R=H, tBu, R '=H, Ph)

Classical and non-classical isomers of both neutral and dianionic BC2P2H3 species, which are isolobal to Cp+ and Cp-, are studied at both B3LYP/6-311++G(d,p) and G3B3 levels of theory. The global minimum structure given by B3LYP/6-311+ + G(d,p) for BC2P2H3 is based on a vinylcyclopropenyl-type structure, whereas BC2P2H32- has a planar aromatic cyclopentadienyl-ion-like structure. However, at the G3B3 level, there are three low-energy isomers for BC2P2H3: 1)tricyclopentane, 2) nido and 3) vinylcyclopropenyl-type structures, all within 1.7 kcal mol(-1) of each other. On the contrary, for the dianionic species the cyclic planar structure is still the minimum. In comparison to the isolobal Cp+ and HnCnP5-n+ isomers, BC2P2H3 shows a competition between pi-delocalised vinylcyclopropenyl- and cluster-type structures (nido and tricyclopentane). Substitution of H on C by tBu, and H on B by Ph, in BC2P2H3 increases the energy difference between the low-lying isomers, giving the lowest energy structure as a tricyclopentane type. Similar substitution in BC2P2H32- merely favours different positional isomers of the cyclic planar geometry, as observed in 1) isoelectronic neutral heterodiphospholes EtBu2C2P2 (E=S, Se, Te), 2) monoanionic heterophospholyl rings EtBu2C2P2 (E=P-, As-, Sb-) and 3) polyphospholyl rings anions tBu(5-n)C(n)P(5-n) (n=0-5). The principal factors that affect the stability of three-, four-, and five-membered ring and acyclic geometrical and positional isomers of neutral and dianionic BC2P2H3 isomers appear to be: 1) relative bond strengths, 2) availability of electrons for the empty 2p boron orbital and 3) steric effects of the tBu groups in the HBC(2)P(2)tBu(2) systems.

Structure and Bonding in Cyclic Isomers of B2AlHnm (n = 3−6, m = −2 to +1): A Comparative Study with B3Hnm, BAl2Hnm and Al3Hnm†

The structure, bonding and energetics of B2AlHnm (n = 3−6, m = −2 to +1) are compared with corresponding homocyclic boron, aluminum analogues and BAl2Hnm using density functional theory (DFT). Divalent to hexacoordinated boron and aluminum atoms are found in these species. The geometrical and bonding pattern in B2AlH4− is similar to that for B2SiH4. Species with lone pairs on the divalent boron and aluminum atoms are found to be minima on the potential energy surface of B2AlH32−. A dramatic structural diversity is observed in going from B3Hnm to B2AlHnm, BAl2Hnm and Al3Hnm and this is attributable to the preference of lower coordination on aluminum, higher coordination on boron and the higher multicenter bonding capability of boron. The most stable structures of B3H6+, B2AlH5 and BAl2H4− and the trihydrogen bridged structure of Al3H32− show an isostructural relationship, indicating the isolobal analogy between trivalent boron and divalent aluminum anion.

Structure and bonding of MCB5H7 and its sandwiched dimer CB5H6M–MCB5H6 (M = Si, Ge, Sn): Isomer stability and preference for slip distorted structure

We find sandwiched metal dimers CB5H6M–MCB5H6 (M = Si, Ge, Sn) which are minima in the potential energy surface with a characteristic M–M single bond. The NBO analysis and the M–M distances (Å) (2.3, 2.44 and 2.81 for M = Si, Ge, Sn) indicate substantial M–M bonding. Formal generation of CB5H6M–MCB5H6 has been studied theoretically. Consecutive substitution of two boron atoms in B7H−27 by M (Si, Ge, Sn) and carbon, respectively followed by dehydrogenation may lead to our desired CB5H6M–MCB5H6. We find that the slip distorted geometry is preferred for MCB5H7 and its dehydrogenated dimer CB5H6M–MCB5H6. The slip-distortion of M–M bond in CB5H6M–MCB5H6 is more than the slip distortion of M–H bond in MCB5H7. Molecular orbital analysis has been done to understand the slip distortion. Larger M–M bending (CB5H6M–MCB5H6) in comparison with M–H bending (MCB5H7) is suspected to be encouraged by stabilization of one of the M–M π bonding MO’s. Preference of M to occupy the apex of pentagonal skeleton of MCB5H7 over its icosahedral analogue MCB10H11 has been observed.

Elastic properties of fast ion conducting lithium based borate glasses

Elastic properties of Li2O-PbO-B2O3 glasses have been investigated using sound velocity measurements at 10 MHz. Four series of glasses have been investigated with different concentrations of Li2O, PbO and B2O3. The variations of molar volume have been examined for the influences of Li2O and PbO. The elastic moduli reveal trends in their compositional dependence. The bulk and shear modulus increases monotonically with increase in the concentration of tetrahedral boron which increases network dimensionality. The variation of bulk moduli has also been correlated to the variation in energy densities. The Poisson's ratio found to be insensitive to the concentration of tetrahedral boron in the structure. The experimental Debye temperatures are in good agreement with the expected theoretical values. Experimental observations have been examined in view, the presence of borate network and the possibility of non-negligible participation of lead in network formation. (c) 2005 Elsevier B.V. All rights reserved.

Characteristics of field-effect transistors based on undoped and B-and N-doped few-layer graphenes

Field-effect transistor characteristics of few-layer graphenes prepared by several methods have been investigated in comparison with those of single-layer graphene prepared by the in situ reduction of single-layer graphene oxide. Ambipolar features have been observed with single-layer graphene and n-type behaviour with all the few-layer graphenes, the best characteristics being found with the graphene possessing 2-3 layers prepared by arc-discharge of graphite in hydrogen. FETs based on boron and nitrogen doped graphene show n-type and p-type behaviour respectively. (C) 2010 Elsevier Ltd. All rights reserved.

The elastic properties of a group of optical glasses by the pulse echo set-up

The pulse-echo apparatus, designed and constructed by the author, has been used to reinvestigate the elastic properties of the eighteen optical glasses. The elastic constants are correct to 0·5%. The results are compared with the earlier investigation which utilised the optical method. The possible causes for large discrepancies observed are critically and briefly discussed. A qualitative interpretation of the results has been successfully attempted. The acoustic velocity increases with the decrease in lead and barium oxides and with increase in calcium oxide and boron trioxide components.

Steroids and related natural products. VIII. Synthesis of oxasteroids

Peroxydisulfuric acid oxidation of testosterone propionate, progesterone, and cholest-4-en-3-one has been shown to yield 3-oxo-17β-hydroxy-4-oxa-5α-androstane (I, after saponification), 3,20-dioxo-4-oxa-5α-pregnane (V) and 3-oxo-4-oxa-5α-cholestane (VII) respectively. Boron trifluoride etherate-lithium aluminum hydride reduction of δ-lactones I, V, and VII led to the corresponding tetrahydropyran derivatives (IIb, VIa, and VIII). Similar reduction of 3β-hydroxy-17-oxo-17a-oxa-D-homo-5α-androstane (XI) gave 3β-hydroxy-17a-oxa-D-homo-5α-androstane (XIIa). Diborane-boron trifluoride etherate was also found to reduce lactones to cyclic ethers, while reduction with diborane gave hemiacetals. Evidence in support of the structures and stereochemistry assigned to the lactones and their unusual reduction products has been summarized. A tentative mechanism is proposed for lactone → ether reduction employing diborane-boron trifluoride etherate.

Generation of Cationic Two-Coordinate Group-13 Ligand Systems by Spontaneous Halide Ejection: Remarkably Nucleophile-Resistant (Dimethylamino)borylene Complexes

Spontaneous ejection of chloride from a three-coordinate boron Lewis acid can be effected by employing very electron rich metal substituents and leads to the formation of a sterically unprotected terminal (dimethylamino)borylene complex that has a short metal-boron bond and remarkable resistance to attack by nucleophilic and protic reagents.

Transport and magnetic properties of conducting polyaniline doped with BX3 (X=F, Cl, and Br)

We report transport and magnetic properties of a different class of highly conducting polyaniline, doped with boron trihalides BX3 (X=F, Cl, and Br). In order to understand the transport mechanism we analyze the temperature dependence of resistivity of a large number of samples, made by pelletizing doped polyaniline powder and by doping films of polyaniline. We find that the charge transport in this class of conducting polyaniline is driven by the charging-energy limited transport of charge carriers, in contrast to the quasi-one-dimensional variable range hopping conduction prevalent in conventional proton-doped polyaniline samples. Magnetic susceptibility provides further insight into the unusually high intrinsic conductivity behavior.

Performance evaluation of an integrated solar water heater as an option for building energy conservation

Since a majority of residential and industrial building hot water needs are around 50 degrees C, an integrated solar water heater could provide a bulk source that blends collection and storage into one unit. This paper describes the design, construction and performance test results of one such water-heating device. The test unit has an absorber area of 1.3 m(2) and can hold 1701 of water, of which extractable volume per day is 1001. Its performance was evaluated under various typical operating conditions. Every morning at about 7:00 a.m., 1001 of hot water were drawn from the sump and replaced with cold water from the mains. Although, during most of the days, the peak temperatures of water obtained are between 50 and 60 degrees C, the next morning temperatures were lower at 45-50 degrees C. Daytime collection efficiencies of about 60% and overall efficiencies of about 40% were obtained. Tests were conducted with and without stratification. Night radiation losses were reduced by use of a screen insulation.

Rearrangement of homobrendane derivatives. Total syntheses of racemic copacamphor, ylangocamphor, and their homologs

Rearrangement of a homobrendane derivative 8a to perhydro-1,4-methanoindenesy stem 9a could be brought about either by p-toluenesulfonic acid or boron trifluoride etherate. Similarly, rearrangement of 8b-d led to the formation of perhydro-1,4-methanoindened erivatives 9b-d. On the basis of the location of substituents in the starting material and the product, a probable mechanistic pathway has been suggested. The appropriate modification of the peripheral functionalities in 9 led to efficient total syntheses of (f)-copacamphor (15a),(f)-ylangocamphor (16a), and their homologues 15b and 16b.