Distribution of products around a burning droplet: an analytical approach

A knowledge of the concentration distribution around a burning droplet is essential if accurate estimates are to be made of the transport coefficients in that region which influence the burning rate. There are two aspects of this paper; (1) determination of the concentration profiles, using the simple assumption of constant binary diffusion coefficients for all species, and comparison with experiments; and (2) postulation of a new relation for the therinal conductivity, which takes into account the variations of both temperature and concentrations of various species. First, the theoretical concentration profiles are evaluated and compared with experimental results reported elsewhere [5]. It is found that the agreement between the theory and experiment is fairly satisfactory. Then, by the use of these profiles and the relations proposed in the literature for the thermal conductivity of a mixture of nonpolar gases, a new relation for thermal conductivity: K = (A1 + B1 T) + (A2 + B2 T) xr (21). is suggested for analytical solutions of droplet combustion problems. Equations are presented to evaluate A1, A2, B1, and B2, and values of these terms for a few hydrocarbons are tabulated.

Development of thermoelectric gas sensors for volatile organic compounds

This paper describes the design and development of a thermoelectric gas sensor suitable for the detection of Volatile Organic Compounds (VOCs). In order to enhance the seebeck coefficient of the sensor, we have deposited chromium metal films on a limited area of the glass substrate. Tin oxide thin film was deposited on top of these metal films. The resulting metal/semiconductor film exhibits a high seebeck coefficient of 400 mu V/ degrees C. Platinum catalyst film deposited on the oxide film to create the necessary temperature gradient resulted in further enhancement in the sensitivity of the sensor to target gases. The sensor shows high sensitivity to ppm-change in the concentration of target hydrocarbons at a relatively low temperature of 120 degrees C.

Saturated liquid densities of cryogenic liquids and refrigerants

The saturated liquid density, varrholr, data along the liquid vapour coexistence curve published in the literature for several cryogenic liquids, hydrocarbons and halocarbon refrigerants are fitted to a generalized equation of the following form varrholr = 1 + A(1 − Tr + B(1 − Tr)β The values of β, the index in phase density differences power law, have been obtained by means of two approaches namely statistical treatment of saturated fluid phase density difference data and the existence of a maximum in T(varrho1 − varrhov) along the saturation curve. Values of the constants A and B are determined utilizing the fact that Tvarrho1 has a maximum at a characteristic temperature T. Values of A, B and β are tabulated for Ne, Ar, Kr, Xe, N2, O2, methane, ethane, propane, iso-butane, n-butane, propylene, ethylene, CO2, water, ammonia, refrigerants-11, 12, 12B1, 13, 13B1, 14, 21, 22, 23, 32, 40, 113, 114, 115, 142b, 152a, 216, 245 and azeotropes R-500, 502, 503, 504. The average error of prediction is less than 2%.

Thermal decomposition studies on copolyurethanes based on hydroxyl terminated polybutadiene and poly(12-hydroxy stearic acid-co-TMP) ester polyol

Thermal degradation of copolyurethanes based on hydroxyl terminated polybutadiene (HTPB) and poly(12-hydroxy stearic acid-co-TMP) ester polyol (PEP) with varying compositions has been studied by thermo-gravimetric and pyrolysis-GC techniques. The copolyurethanes were found to decompose in multiple stages and the kinetic parameters were found to be dependent on the method of their evaluation. The activation energy for the initial stage of decomposition was found to increase, and for the main stage decreases with the increase in PEP content. The pyrolysis-GC studies on the ammonium perchlorate filled copolyurethanes (solid propellants) showed that the major products during the pyrolysis were C-2, C-3 hydrocarbons and butadiene. The amount of C-2 fraction in the pyrolyslate increased with solid loading, as well as with the HTPB content in the copolyurethanes. A linear relationship apparently exists between the amount of C-2 fraction and the burn rates of the solid propellants. (C) 2000 Elsevier Science Ltd. All rights reserved.

Spectroscopic, microscopic and first rheological investigations in charge-transfer interaction induced organogels

This article describes two-component charge-transfer interaction mediated organogels (CT-gels) derived from anthracene carboxamides obtained from 2-amino 2-hydroxymethyl-1,3-propanediol (TRIS), and 2,3-dialkoxyanthracenes as donors, with 2,4,7-trinitrofluorenone (TNF) as the common acceptor. We demonstrate the versatility of TNF as an electron acceptor in the formation of these gels. The effect of subtle changes in the donor structure on the gelation ability has been investigated by varying the alkyl chain length in the dialkoxyanthracene donors, and by varying the position of the TRIS substituent in the anthracene carboxamide donors. Distinct differences have been observed in the nature of the CT-gels based on these two kinds of anthracene donors. It has been reported in the literature that 2,3-dialkoxyanthracenes form gels on their own in various aliphatic hydrocarbons and alcohols for linear alkyl chains bearing at least 6mcarbon atoms (C-6). In the present study, it is shown that themCT-complex of these molecules with TNF is able to gel many alcoholic and a few hydrocarbon solvents. Also, in the presence of TNF, the 2,3-dialkoxyanthracenes (C-4-C-5) which were non-gelators on their own at ambient temperatures, form CT-gels in a number of alcohols. The other series of gelators discussed, the anthracene carboxamides, require the mandatory presence of TNF to form gels. This donor-acceptor complex forms gels in various aliphatic alcohols. Interestingly, the formation of these CT-gels requires rapid cooling in most of the cases. Thermal stability studies with both types of CT-gels indicate an optimum stoichiometry of 1 : 1 between the donor and the acceptor. Dynamic rheological experiments reveal these gels as viscoelastic soft materials, with the mechanical strength of these gels depending on the amount of TNF present. This provides a means to tune the strength of the gel by varying the doping concentration of the acceptor.

Estradiol - 17β induces polyaromatic hydrocarbon-inducible cytochrome P-450 in chicken liver

A cDNA clone has been isolated from a chicken liver library prepared against messenger RNA isolated after chronic estradiol-17β treatment. The clone, pP-450 IA - 61, has an insert of 900nt and the sequence shows high homology to CYPIA2 subfamily from four other species. A single injection of estradiol-17β to immature chicken results in a striking induction of mRNA hybridizing to labeled pP-450IA - 61. The probe also hybridizes to mRNA induced by 3 — methylcholanthrene in chicken. These results offer direct proof for the similarity in the mode of action at the transcriptional level of polyaromatic hydrocarbons and estrogenic compounds.

Thermogravimetric and mass-spectrometric study of the thermal decomposition of PBCT resins

The thermal decomposition of three commercial samples of carboxy-terminated polybutadiene (PBCT) resins was studied by thermogravimetric analysis (TGA) at heating rates varying from 2° to 100°C/min. Kinetic parameters of the decomposition process at different heating rates were evaluated by means of the Fuoss method.1 The decomposition process and the activation energy values are found to be dependent on heating rate. Mass-spectrometric analysis of the decomposition products shows that the pyrolysis products of PBCT resins are mainly low molecular weight hydrocarbons: ethylene, acetylene, butadiene, propadiene, vinylcyclohexene, etc. The rates of evolution of these hydrocarbon products vary with the carboxy content of the PBCT resin. Based on this, a carbonium ion mechanism has been suggested for the thermal decomposition. The data generated from this work are of importance for a consideration of the mechanism of combustion of composite solid propellants based on PBCT binders.

Mechanistic evaluation of mitigation of petroleum hydrocarbon contamination by soil medium

Present in situ chemical treatment technologies for mitigation of petroleum hydrocarbon contamination are in the developmental stage or being tested. To devise efficient strategies for restricting the movement of petroleum hydrocarbon (PHC) molecules in the contaminated soil, it is proposed to utilize the sorption–interaction relationships between the petroleum contaminants and the soil substrate. The basic questions addressed in this paper are as follows (i) What are the prominent chemical constituents of the various petroleum fractions that interact with the soil substrate? (ii) What are the functional groups of a soil that interact with the contaminants? (iii) What are the bonding mechanisms possible between the soil functional groups and the PHC contaminants? (iv) What are the consequent changes brought about the soil physical properties on interaction with PHC's? (v) What are the factors influencing the interactions between PHC molecules and clay particles of the soil substrate? (vi) What is the possibility of improving the soil's attenuation ability for PHC's? The development of answers to the basic questions reveal that petroleum hydrocarbons comprise a mixture of nonpolar alkanes and aromatic and polycyclic hydrocarbons, that have limited solubility in water. The bonding mechanism between the nonpolar PHC's and the clay surface is by way of van der Waals attraction. The adsorption of the nonpolar hydrocarbons by the clay surface occurs only when their (i.e., the hydrocarbon molecules) solubility in water is exceeded and the hydrocarbons exist in the micellar form. Dilute solutions of hydrocarbons in water, i.e., concentrations of hydrocarbons at or below the solubility limit, have no effect on the hydraulic conductivity of clay soils. Permeation with pure hydrocarbons invariably influences the clay hydraulic conductivity. To improve the attenuation ability of soils towards PHC's, it is proposed to coat the soil surface with "ultra" heavy organic polymers. Adsorption of organic polymers by the clay surface may change the surface properties of the soil from highly hydrophilic (having affinity for water molecules) to organophilic (having affinity for organic molecules). The organic polymers attached to the clay surface are expected to attenuate the PHC molecules by van der Waals attraction, by hydrogen bonding, and also by adsorption into interlayer space in the case of soils containing swelling clays.

V2o5-Based Hydrocarbon Sensors

V2O5 supported on ZrO2 is found to be an excellent sensor for n-propane-butane mixtures at 625 K; in-situ X-ray diffraction studies show that V2O5 is reduced to VO2 with a metastable monoclinic structure on contact with the hydrocarbons and is oxidised back to the parent oxide on exposure to air.

Is tetramethyleneethane a ground state triplet?

We have examined a number of possible ways by which tetramethyleneethane (TME) can be a ground state triplet, as claimed by experimental studies, in violation of Ovchinnikov’s theorem for alternant hydrocarbons of equal bond lengths. Model exact π calculations of the low-lying states of TME, 3,4-dimethylenefuran and 3,4-dimethylenepyrrole were carried out using a diagrammatic valence bond approach. The calculations failed to yield a triplet ground state even after (a) tuning of electron correlation, (b) breaking alternancy symmetry, and (c) allowing for geometric distortions. In contrast to earlier studies of fine structure constants in other conjugated systems, the computedD andE values of all the low-lying triplet states of TME for various geometries are at least an order of magnitude different from the experimentally reported values. Incorporation of σ-π mixing by means of UHF MNDO calculations is found to favour a singlet ground state even further. A reinterpretation of the experimental results of TME is therefore suggested to resolve the conflict.

Temperature-programmed desorption and surface reaction of thiophene over co-mo/.gamma.-Al2O3 hydrodesulfurization catalysts

The temperature-programmed desorption (TPD) and temperature-programmed surface reaction (TPSR) of thiophene over a series of Co-Mo/gamma-Al2O3, hydrodesulfurization (HDS) catalysts with varying Co to Mo ratios have been studied with the objective of understanding the promotional role of Co in the HDS reaction. As part of the study, the desorptions (TPD) and hydrogenations (TPSR) of butane, butene, and butadiene over these catalysts have also been investigated. The TPD of the hydrocarbons over catalysts containing no Co showed a single desorption profile while incorporation of Co created an additional site, with higher heats of desorption, without significantly affecting desorption from the original site. The TPSR measurements showed that the two sites had separate and independent activity for the hydrogenation of the C-4 hydrocarbons. The TPD of thiophene over catalysts with varying Co to Mo ratios showed a single desorption profile with identical heats of desorption, implying that Co does not affect or influence the adsorption sites for thiophene. The TPSR of the HDS of thiophene, however, showed that, although the products of the HDS reaction-butane, butene, and H2S-are the same irrespective of the Co content, the temperature profiles and the activation barriers for the formation of these species show considerable change with the Co/Co+Mo ratio. The results are discussed in light of the existing models for the promotional role of Co in the HDS reaction.

Methanol-to-gasoline (MTG) conversion over ZSM-5. A temperature programmed surface reaction study

The conversion of methanol to gasoline over zeolite ZSM-5 has been studied by temperature programmed surface reaction (TPSR). The technique is able to monitor the two steps in the process: the dehydration of methanol to dimethyl ether and the subsequent conversion of dimethyl ether to hydrocarbons. The activation barriers associated with each step were evaluated from the TPSR profiles and are 25.7 and 46.5 kcal/mol respectively. The methanol desorption profile shows considerable change with the amount of methanol molecules adsorbed per Bronsted site of the zeolite. The energy associated with the desorption process, (CH3OHH+-ZSM5 --> (CH3OHH+-ZSM5 + CH3OH, shows a spectrum of values depending on n.

Novel reduction (Zn-AcOH) of DDHQ esters - A new route to tropone synthesis

Zn/acetic acid reaction of DDHQ esters 1 a-d gave the saturated acids 3 a-d and the hydrocarbons 7 a-d. The intermediacy of the aldehydes 10 and 11 in the formation of the products has been established. Oxidation of hydrocarbons 7a and 7b gave the corresponding tropones (5a and 5b).

Production of biosurfactant “Biosur-Pm” by Pseudomonas maltophila CSV89: characterization and role in hydrocarbon uptake

Pseudomonas maltophilia CSV89, a soil bacterium, produces an extracellular biosurfactant, ''Biosur-Pm''. The partially purified product is nondialyzable and chemically composed of 50% protein and 12-15% sugar, which indicates the complex nature of Biosur-Pm. It reduces the surface tension of water from 73 to 53 x 10(-3) N m(-1) and has a critical micellar concentration of 80 mg/l. Compared to aliphatic hydrocarbons, Biosur-Pm shows good activity against aromatic hydrocarbons. The emulsion formed is stable and does not require any metal ions for emulsification. The kinetics of Biosur-Pm production suggest that its synthesis isa growth-associated and pH-dependent process. At pH 7.0, cells produced more Biosur-Pm with less cell surface hydrophobicity. At pH 8.0, however, the cells produced less Biosur-Pm with more cell surface hydrophobicity and showed a twofold higher affinity for aromatic hydrocarbons compared to the cells grown at pH 7.0. The Biosur-Pm showed a pH-dependent release, stimulated growth of the producer strain on mineral salts medium with 1-naphthoic acid when added externally, and facilitated the conversion of salicylate to catechol. All these results suggest that Biosur-Pm is probably a cell-wall component and helps in hydrocarbon assimilation/uptake.

A method for the calculation of the adsorbed phase volume and pseudo-saturation pressure from adsorption isotherm data on activated carbon

We propose a new method for evaluating the adsorbed phase volume during physisorption of several gases on activated carbon specimens. We treat the adsorbed phase as another equilibrium phase which satisfies the Gibbs equation and hence assume that the law of rectilinear diameters is applicable. Since invariably the bulk gas phase densities are known along measured isotherms, the constants of the adsorbed phase volume can be regressed from the experimental data. We take the Dubinin-Astakhov isotherm as the model for verifying our hypothesis since it is one of the few equations that accounts for adsorbed phase volume changes. In addition, the pseudo-saturation pressure in the supercritical region is calculated by letting the index of the temperature term in Dubinin's equation to be temperature dependent. Based on over 50 combinations of activated carbons and adsorbates (nitrogen, oxygen, argon, carbon dioxide, hydrocarbons and halocarbon refrigerants) it is observed that the proposed changes fit experimental data quite well.