Field intercomparison of four methane gas analysers suitable for eddy covariance flux measurements

Eddy covariance (EC)-flux measurement technique is based on measurement of turbulent motions of air with accurate and fast measurement devices. For instance, in order to measure methane flux a fast methane gas analyser is needed which measures methane concentration at least ten times in a second in addition to a sonic anemometer, which measures the three wind components with the same sampling interval. Previously measurement of methane flux was almost impossible to carry out with EC-technique due to lack of fast enough gas analysers. However during the last decade new instruments have been developed and thus methane EC-flux measurements have become more common. Performance of four methane gas analysers suitable for eddy covariance measurements are assessed in this thesis. The assessment and comparison was performed by analysing EC-data obtained during summer 2010 (1.4.-26.10.) at Siikaneva fen. The four participating methane gas analysers are TGA-100A (Campbell Scientific Inc., USA), RMT-200 (Los Gatos Research, USA), G1301-f (Picarro Inc., USA) and Prototype-7700 (LI-COR Biosciences, USA). RMT-200 functioned most reliably throughout the measurement campaign and the corresponding methane flux data had the smallest random error. In addition, methane fluxes calculated from data obtained from G1301-f and RMT-200 agree remarkably well throughout the measurement campaign. The calculated cospectra and power spectra agree well with corresponding temperature spectra. Prototype-7700 functioned only slightly over one month in the beginning of the measurement campaign and thus its accuracy and long-term performance is difficult to assess.

Mikä yliopisto-opiskelijaa kiihdyttää? : Opiskeluympäristöjen tutkimusta CASS-kokemusotantamenetelmällä flow-teoriaa ja ydintunneteorioita soveltaen

Flow experience is often defined either as an experience of high concentration and enjoyment or as a situation, where high challenges are matched with high skills. According to core-emotion theories, the experience of any emotion contains two core emotions: valence and arousal. Through an accurate mathematical model, the present study investigated, whether the experience of concentration and enjoyment is related to situations where both challenge and skills are high and in balance. Further, it was investigated what sort of core emotions are related to differing relationships between challenge and skills. Finally, university students’ experiences of their natural study environments were described in terms of core emotions and in terms of relationships between challenge and skills. Participants were 55 university students who participated two weeks research period. Altogether 3367 questionnaire answers were collected with the CASS experience-sampling method, operating in 3G-mobile phones. The relationship between challenge and skills (competence) was defined in an exact way in polar coordinates. An enjoyable and concentrated flow experience was defined as a sum variable of absorption, interest and enthusiasm. Core emotions were calculated with factor analysis from nine emotion variables. As expected, an experience of concentration and enjoyment was, on average, related to the situations where both challenge and skills were high and in balance. This was not, however, the case in every situation. Thus, it should be taken into consideration how flow experience is operationalised in experience sampling studies. When flow experience was defined as a situation of high challenge and high skills, it was often related to high valence and arousal emotions such as excitement or enthusiasm. A happier or a more tranquil enjoyment was related to situations of moderate challenge and high skills. Experiences differed clearly between various natural study environments. At lectures students were often bored or mentally absent, and did not experience challenges. In a small group students were often excited or enthusiastic, and showed optimal balance between challenge and skills. At library students felt satisfied and were engaged in highly challenging work.

Oral Health among Young Adults and the Middle-aged in Iran

The aim of the present study was to assess oral health and treatment needs among adult Iranians according to socio-demographic status, smoking, and oral hygiene, and to investigate the relationships between these determinants and oral health. Data for 4448 young adult (aged 18) and 8301 middle-aged (aged 35 to 44) Iranians were collected in 2002 as part of a national survey using the World Health Organization (WHO) criteria for sampling and clinical diagnoses, across 28 provinces by 33 calibrated examiners. Gender, age, place of residence, and level of education served as socio-demographic information, smoking as behavioural and modified plaque index (PI) as the biological risk indicator for oral hygiene. Number of teeth, decayed teeth (DT), filled teeth (FT), decayed, missing, filled teeth (DMFT), community periodontal index (CPI), and prosthodontic rehabilitation served as outcome variables of oral health. Mean number of DMFT was 4.3 (Standard deviation (SD) = 3.7) in young adults and 11.0 (SD = 6.4) among middle-aged individuals. Among young adults the D-component (DT = 70%), and among middle-aged individuals the M-component (60%) dominated in the DMFT index. Among young adults, visible plaque was found in nearly all subjects. Maximum (max) PI was associated with higher mean number of DT, and higher periodontal treatment needs. A healthy periodontium was a rare condition, with 8% of young adults and 1% of middle-aged individuals having a max CPI = 0. The majority of the CPI findings among young adults consisted of calculus (48%) and deepened periodontal pockets (21%). Respective values for middle-aged individuals were 40% and 53%. Having a deep pocket (max CPI = 4) was more likely among young adults with a low level of education (Odds ratio (OR) = 2.7, 95% Confidence interval (CI) = 1.9–4.0) than it was among well-educated individuals. Among middle-aged individuals, having calculus or a periodontal pocket was more likely in men (OR = 1.8, 95% CI = 1.6–2.0) and in illiterate subjects (OR = 6.3, 95% CI = 5.1–7.8) than it was for their counterparts. Among young adults, having 28 teeth was more (p < 0.05) prevalent among men (72% vs. 68% for women), urban residents (71% vs. 67% for rural residents), and those with a high level of education (73% vs. 60% for those with a low level). Among middle-aged individuals, having a functional dentition was associated with younger age (OR = 2.0, 95% CI = 1.7−2.5) and higher level of education (OR = 1.8, 95% CI = 1.6−2.1). Of middle-aged individuals, 2% of 35- to 39-year-olds and 5% of those aged 40 to 44 were edentulous. Among the dentate subjects (n = 7,925), prosthodontic rehabilitation was more prevalent (p < 0.001) among women, urban residents, and those with a high level of education than it was among their counterparts. Among those having 1 to 19 teeth, a removable denture was the most common type of prosthodontic rehabilitation. Middle-aged individuals lacking a functional dentition were more likely (OR = 6.0, 95% CI = 4.8−7.6) to have prosthodontic rehabilitation than were those having a functional dentition. In total, 81% of all reported being non-smokers, and 32% of men and 5% of women were current smokers. Heavy smokers were the most likely to have deepened periodontal pockets (max CPI ≥ 3, OR = 2.9, 95% CI = 1.8−4.7) and to have less than 20 teeth (OR = 2.3, 95% CI = 1.5−3.6). The findings indicate impaired oral health status in adult Iranians, particularly those of low socio-economic status and educational level. The high prevalence of dental plaque and calculus and considerable unmet treatment needs call for a preventive population strategy with special emphasis on the improvement of oral self-care and smoking cessation to tackle the underlying risk factors for oral diseases in the Iranian adult population.

Estimation of local forest attributes, utilizing two-phase sampling and auxiliary data

This thesis examines the feasibility of a forest inventory method based on two-phase sampling in estimating forest attributes at the stand or substand levels for forest management purposes. The method is based on multi-source forest inventory combining auxiliary data consisting of remote sensing imagery or other geographic information and field measurements. Auxiliary data are utilized as first-phase data for covering all inventory units. Various methods were examined for improving the accuracy of the forest estimates. Pre-processing of auxiliary data in the form of correcting the spectral properties of aerial imagery was examined (I), as was the selection of aerial image features for estimating forest attributes (II). Various spatial units were compared for extracting image features in a remote sensing aided forest inventory utilizing very high resolution imagery (III). A number of data sources were combined and different weighting procedures were tested in estimating forest attributes (IV, V). Correction of the spectral properties of aerial images proved to be a straightforward and advantageous method for improving the correlation between the image features and the measured forest attributes. Testing different image features that can be extracted from aerial photographs (and other very high resolution images) showed that the images contain a wealth of relevant information that can be extracted only by utilizing the spatial organization of the image pixel values. Furthermore, careful selection of image features for the inventory task generally gives better results than inputting all extractable features to the estimation procedure. When the spatial units for extracting very high resolution image features were examined, an approach based on image segmentation generally showed advantages compared with a traditional sample plot-based approach. Combining several data sources resulted in more accurate estimates than any of the individual data sources alone. The best combined estimate can be derived by weighting the estimates produced by the individual data sources by the inverse values of their mean square errors. Despite the fact that the plot-level estimation accuracy in two-phase sampling inventory can be improved in many ways, the accuracy of forest estimates based mainly on single-view satellite and aerial imagery is a relatively poor basis for making stand-level management decisions.

Digitoitujen väri-infrailmakuvien numeerinen monikuvatulkinta metsäninventoinnissa

The use of remote sensing imagery as auxiliary data in forest inventory is based on the correlation between features extracted from the images and the ground truth. The bidirectional reflectance and radial displacement cause variation in image features located in different segments of the image but forest characteristics remaining the same. The variation has so far been diminished by different radiometric corrections. In this study the use of sun azimuth based converted image co-ordinates was examined to supplement auxiliary data extracted from digitised aerial photographs. The method was considered as an alternative for radiometric corrections. Additionally, the usefulness of multi-image interpretation of digitised aerial photographs in regression estimation of forest characteristics was studied. The state owned study area located in Leivonmäki, Central Finland and the study material consisted of five digitised and ortho-rectified colour-infrared (CIR) aerial photographs and field measurements of 388 plots, out of which 194 were relascope (Bitterlich) plots and 194 were concentric circular plots. Both the image data and the field measurements were from the year 1999. When examining the effect of the location of the image point on pixel values and texture features of Finnish forest plots in digitised CIR photographs the clearest differences were found between front-and back-lighted image halves. Inside the image half the differences between different blocks were clearly bigger on the front-lighted half than on the back-lighted half. The strength of the phenomenon varied by forest category. The differences between pixel values extracted from different image blocks were greatest in developed and mature stands and smallest in young stands. The differences between texture features were greatest in developing stands and smallest in young and mature stands. The logarithm of timber volume per hectare and the angular transformation of the proportion of broadleaved trees of the total volume were used as dependent variables in regression models. Five different converted image co-ordinates based trend surfaces were used in models in order to diminish the effect of the bidirectional reflectance. The reference model of total volume, in which the location of the image point had been ignored, resulted in RMSE of 1,268 calculated from test material. The best of the trend surfaces was the complete third order surface, which resulted in RMSE of 1,107. The reference model of the proportion of broadleaved trees resulted in RMSE of 0,4292 and the second order trend surface was the best, resulting in RMSE of 0,4270. The trend surface method is applicable, but it has to be applied by forest category and by variable. The usefulness of multi-image interpretation of digitised aerial photographs was studied by building comparable regression models using either the front-lighted image features, back-lighted image features or both. The two-image model turned out to be slightly better than the one-image models in total volume estimation. The best one-image model resulted in RMSE of 1,098 and the two-image model resulted in RMSE of 1,090. The homologous features did not improve the models of the proportion of broadleaved trees. The overall result gives motivation for further research of multi-image interpretation. The focus may be improving regression estimation and feature selection or examination of stratification used in two-phase sampling inventory techniques. Keywords: forest inventory, digitised aerial photograph, bidirectional reflectance, converted image co­ordinates, regression estimation, multi-image interpretation, pixel value, texture, trend surface

Biological Control of Oilseed Rape Pests with Entomopathogenic Nematodes

Biological control techniques attract increasing attention as one of the sustainable alternatives to pesticide use in integrated pest management programs. In order to develop sustainable pest management methods for arable crops based on entomopathogenic nematodes (EPN), their efficacy and persistence needed to be investigated, and an economically feasible delivery system had to be developed. In this study, first a survey of entomopathogens was conducted, and a system approach was tested, using the oilseed Brassica (OSB) growing system (OSB, spring wheat, and red clover) as a model. The system approach aimed at determining the potential of Steinernema feltiae (Filipjev) for the control of OSB pests, developing OSB rotation schemes that support EPN persistence, and investigating the impact of the selected biotic and abiotic factors on efficacy and persistence of EPN. This study employed abductive logic (which employs constant interplay between the theory and empirical observation), quantitative methods, and a case study on OSB. Laboratory and field experiments were carried out, and two types of pathogen surveys. A horizontal survey included OSB fields across Estonia, Germany, Poland, Sweden and the UK, while a vertical survey included sampling from two sets of differently managed experimental fields during three years. A new approach was introduced for measuring occurrence, where the prevalence and relative intensity of entomopathogens, biotic agents, and unidentified insect antagonists were determined. The effect of dose, timing, and the application method on S. feltiae in the control of pests in OSB, and the potential of a controlled release delivery system (CRS) were evaluated in the field. Studies on the impact of selected biotic and abiotc factors (Brassica plant, bait insects, developmental stages of Meligethes aeneus Fab., Isaria fumosorosea Wize (Ifr), and organic and synthetic fertilizers) on the efficacy of S. feltiae were conducted in the laboratory. Persistence of S. feltiae in the OSB growing system, and the effect of dose, timing, and the application method, was assessed in the field as part of the efficacy experiments. The impact of selected biotic and abiotic factors on S. feltiae persistence was assessed in laboratory experiments. The pathogen survey showed that the occurrence of entomopathogens is low in the OSB growing system, and that a management system causing less disturbance (ICM) to the soil increases the relative intensity of insect parasitic nematodes and other insect antagonists. A longer study period is required to show any possible impact of ICM on the relative intensity of entomopathogenic fungi, or on the prevalence of entomopathogens. Two different measures of the occurrence yielded different results: the relative intensity revealed the difference between the two different crop management methods, while prevalence did not. The highest efficacy of S. feltiae was achieved by using a low dose and targeting all stages of M. aeneus. When only the larval stage was targeted, the application method and dose had no significant effect. The CRS decreased the pest abundance significantly more than the surface application method. S. feltiae persisted in the OSB fields in Finland for several months, but did not survive the winter. The strain survived for 7 months when it was applied in autumn in Germany, but its populations declined rapidly after winter. The examined biotic and abiotic factors had variable impacts on S. feltiae efficacy and persistence. The two measures, prevalence and relative intensity of entomopathogens, gave valuable information for their use in biocontrol programs. The recommended biocontrol strategy for OSB growing in Finland is inundation and seasonal inoculation of EPN. The impact of some biotic and abiotic factors on S. feltiae efficacy and persistence is significant, and can be used to improve the efficacy of EPN. The CRS is a novel alternative for EPN application, and should also be considered for use on other crops. Keywords: Biological control, inundation, inoculation, conservation, formulation, slow release method, crop rotation, Entomopathogenic nematodes, Steinernema feltiae, oilseed rape pests, Meligethes aeneus, Phyllotreta spp., occurrence, prevalence, intensity, efficacy, persistence, field, Isaria fumosorosea, biotic factors, abiotic factors, interaction, impact, insect stages, integrated crop management, standard (conventional) crop management

Chemical and source characterisation of size-segregated urban air particulate matter

Recent epidemiological studies have shown a consistent association of the mass concentration of urban air thoracic (PM10) and fine (PM2.5) particles with mortality and morbidity among cardiorespiratory patients. However, the chemical characteristics of different particulate size ranges and the biological mechanisms responsible for these adverse health effects are not well known. The principal aims of this thesis were to validate a high volume cascade impactor (HVCI) for the collection of particulate matter for physicochemical and toxicological studies, and to make an in-depth chemical and source characterisation of samples collected during different pollution situations. The particulate samples were collected with the HVCI, virtual impactors and a Berner low pressure impactor in six European cities: Helsinki, Duisburg, Prague, Amsterdam, Barcelona and Athens. The samples were analysed for particle mass, common ions, total and water-soluble elements as well as elemental and organic carbon. Laboratory calibration and field comparisons indicated that the HVCI can provide a unique large capacity, high efficiency sampling of size-segregated aerosol particles. The cutoff sizes of the recommended HVCI configuration were 2.4, 0.9 and 0.2 μm. The HVCI mass concentrations were in a good agreement with the reference methods, but the chemical composition of especially the fine particulate samples showed some differences. This implies that the chemical characterization of the exposure variable in toxicological studies needs to be done from the same HVCI samples as used in cell and animal studies. The data from parallel, low volume reference samplers provide valuable additional information for chemical mass closure and source assessment. The major components of PM2.5 in the virtual impactor samples were carbonaceous compounds, secondary inorganic ions and sea salt, whereas those of coarse particles (PM2.5-10) were soil-derived compounds, carbonaceous compounds, sea salt and nitrate. The major and minor components together accounted for 77-106% and 77-96% of the gravimetrically-measured masses of fine and coarse particles, respectively. Relatively large differences between sampling campaigns were observed in the organic carbon content of the PM2.5 samples as well as the mineral composition of the PM2.5-10 samples. A source assessment based on chemical tracers suggested clear differences in the dominant sources (e.g. traffic, residential heating with solid fuels, metal industry plants, regional or long-range transport) between the sampling campaigns. In summary, the field campaigns exhibited different profiles with regard to particulate sources, size distribution and chemical composition, thus, providing a highly useful setup for toxicological studies on the size-segregated HVCI samples.

Remote sensing of leaf area index: enhanced retrieval from close-range and remotely sensed optical observations

A wide range of models used in agriculture, ecology, carbon cycling, climate and other related studies require information on the amount of leaf material present in a given environment to correctly represent radiation, heat, momentum, water, and various gas exchanges with the overlying atmosphere or the underlying soil. Leaf area index (LAI) thus often features as a critical land surface variable in parameterisations of global and regional climate models, e.g., radiation uptake, precipitation interception, energy conversion, gas exchange and momentum, as all areas are substantially determined by the vegetation surface. Optical wavelengths of remote sensing are the common electromagnetic regions used for LAI estimations and generally for vegetation studies. The main purpose of this dissertation was to enhance the determination of LAI using close-range remote sensing (hemispherical photography), airborne remote sensing (high resolution colour and colour infrared imagery), and satellite remote sensing (high resolution SPOT 5 HRG imagery) optical observations. The commonly used light extinction models are applied at all levels of optical observations. For the sake of comparative analysis, LAI was further determined using statistical relationships between spectral vegetation index (SVI) and ground based LAI. The study areas of this dissertation focus on two regions, one located in Taita Hills, South-East Kenya characterised by tropical cloud forest and exotic plantations, and the other in Gatineau Park, Southern Quebec, Canada dominated by temperate hardwood forest. The sampling procedure of sky map of gap fraction and size from hemispherical photographs was proven to be one of the most crucial steps in the accurate determination of LAI. LAI and clumping index estimates were significantly affected by the variation of the size of sky segments for given zenith angle ranges. On sloping ground, gap fraction and size distributions present strong upslope/downslope asymmetry of foliage elements, and thus the correction and the sensitivity analysis for both LAI and clumping index computations were demonstrated. Several SVIs can be used for LAI mapping using empirical regression analysis provided that the sensitivities of SVIs at varying ranges of LAI are large enough. Large scale LAI inversion algorithms were demonstrated and were proven to be a considerably efficient alternative approach for LAI mapping. LAI can be estimated nonparametrically from the information contained solely in the remotely sensed dataset given that the upper-end (saturated SVI) value is accurately determined. However, further study is still required to devise a methodology as well as instrumentation to retrieve on-ground green leaf area index . Subsequently, the large scale LAI inversion algorithms presented in this work can be precisely validated. Finally, based on literature review and this dissertation, potential future research prospects and directions were recommended.

Computational Techniques for Haplotype Inference and for Local Alignment Significance

This thesis which consists of an introduction and four peer-reviewed original publications studies the problems of haplotype inference (haplotyping) and local alignment significance. The problems studied here belong to the broad area of bioinformatics and computational biology. The presented solutions are computationally fast and accurate, which makes them practical in high-throughput sequence data analysis. Haplotype inference is a computational problem where the goal is to estimate haplotypes from a sample of genotypes as accurately as possible. This problem is important as the direct measurement of haplotypes is difficult, whereas the genotypes are easier to quantify. Haplotypes are the key-players when studying for example the genetic causes of diseases. In this thesis, three methods are presented for the haplotype inference problem referred to as HaploParser, HIT, and BACH. HaploParser is based on a combinatorial mosaic model and hierarchical parsing that together mimic recombinations and point-mutations in a biologically plausible way. In this mosaic model, the current population is assumed to be evolved from a small founder population. Thus, the haplotypes of the current population are recombinations of the (implicit) founder haplotypes with some point--mutations. HIT (Haplotype Inference Technique) uses a hidden Markov model for haplotypes and efficient algorithms are presented to learn this model from genotype data. The model structure of HIT is analogous to the mosaic model of HaploParser with founder haplotypes. Therefore, it can be seen as a probabilistic model of recombinations and point-mutations. BACH (Bayesian Context-based Haplotyping) utilizes a context tree weighting algorithm to efficiently sum over all variable-length Markov chains to evaluate the posterior probability of a haplotype configuration. Algorithms are presented that find haplotype configurations with high posterior probability. BACH is the most accurate method presented in this thesis and has comparable performance to the best available software for haplotype inference. Local alignment significance is a computational problem where one is interested in whether the local similarities in two sequences are due to the fact that the sequences are related or just by chance. Similarity of sequences is measured by their best local alignment score and from that, a p-value is computed. This p-value is the probability of picking two sequences from the null model that have as good or better best local alignment score. Local alignment significance is used routinely for example in homology searches. In this thesis, a general framework is sketched that allows one to compute a tight upper bound for the p-value of a local pairwise alignment score. Unlike the previous methods, the presented framework is not affeced by so-called edge-effects and can handle gaps (deletions and insertions) without troublesome sampling and curve fitting.

Short-term effects of variable retention on epigaeic spiders and carabid beetles in Finland

Forestry has influenced forest dwelling organisms for centuries in Fennoscandia. For example, in Finland ca. 30% of the threatened species are threatened because of forestry. Nowadays forest management recommendations include practices aimed at maintaining biodiversity in harvesting, such as green-tree retention. However, the effects of these practices have been little studied. In variable retention, different numbers of trees are retained, varying from green-tree retention (at least a few live standing trees in clear-cuts) to thinning (only individual trees removed). I examined the responses of ground-dwelling spiders and carabid beetles to green-tree retention (with small and large tree groups), gap felling and thinning aimed at an uneven age structure of trees. The impacts of these harvesting methods were compared to those of clear-cutting and uncut controls. I aimed to test the hypothesis that retaining more trees positively affects populations of those species of spiders and carabids that were present before harvesting. The data come from two studies. First, spiders were collected with pitfall traps in south-central Finland in 1995 (pre-treatment) and 1998 (after-treatment) in order to examine the effects of clear-cutting, green-tree retention (with 0.01-0.02-ha sized tree groups), gap felling (with three 0.16-ha sized openings in a 1-ha stand), thinning aiming at an uneven age structure of trees and uncut control. Second, spiders and carabids were caught with pitfall traps in eastern Finland in 1998-2001 (pre-treatment and three post-treatment years) in eleven 0.09-0.55-ha sized retention-tree groups and clear-cuts adjacent to them. Original spider and carabid assemblages were better maintained after harvests that retained more trees. Thinning maintained forest spiders well. However, gap felling and large retention-tree groups maintained some forest spider and carabid species in the short-term, but negatively affected some species over time. However, use of small retention-tree groups was associated with negative effects on forest spider populations. Studies are needed on the long-term effects of variable retention on terrestrial invertebrates; especially those directed at defining appropriate retention patch size and on the importance of structural diversity provided by variable retention for invertebrate populations. However, the aims of variable retention should be specified first. For example, are retention-tree groups planned to constitute life-boats , stepping-stones or to create structural diversity? Does it suffice that some species are maintained, or do we want to preserve the most sensitive ones, and how are these best defined? Moreover, the ecological benefits and economic costs of modified logging methods should be compared to other approaches aimed at maintaining biodiversity.

Cortinarius subgenus Telamonia p.p. in North Europe

Cortinarius is the largest genus of Agaricales with a worldwide distribution. So far, over 4000 Cortinarius names and combinations have been published. Cortinarius spp. form ectomycorrhizae with different trees and shrubs. A majority of the Cortinarius species have narrow ecological preferences and many form ectomycorrhiza with only one or few host species. The subgenus Telamonia sensu lato (s. lat.), comprising the greatest number of species, is the most poorly known of the subgenera of Cortinarius. The centre of diversity is in the northern hemisphere, although some species of the group are also recognized in the southern hemisphere. The aim of this thesis was to study the taxonomy of Cortinarius subgenus Telamonia p.p. species based on morphological and molecular data, as well as to study the ecology and distribution of the species in North Europe. The taxonomical problems encountered and the difficulty in finding and studying all the relevant names and types slowed down the study. The diversity of the subgenus Telamonia s. lat. in North Europe (excluding sect. Hydrocybe, Icrustati and Anomali) was found to be far greater than previously thought. Even many of the common species have not yet been described. So far, ca. 200 species have been recognised from the Nordic countries, but the sampling in most groups does not cover the whole diversity and especially the southern deciduous forest species are underrepresented in our study. In most cases phylogenetic (only based on ITS data) and morphological species recognition were in concordance, but in a few cases morphologically delimited species had almost identical ITS sequences, raising the question as to whether ITS is always variable enough for species recognition. The opposite situation, in which a morphologically uniform species included two phylogenetically distinct lineages, however, was also encountered, suggesting the possibility of cryptic species in Cortinarius. In our studies no taxa below species level were recognised and the aforementioned results indicate that presumably they can only be recognised genetically. Based on our preliminary results a revision of the infrageneric classification in Cortinarius subgenus Telamonia s. lat. is needed, and more sections should be established for a meaningful and functional classification. Many groups have turned out to be artificial, and it seems evident that many characteristics have been over- or underemphasised. Many morphological characteristics, however, are useful in the identification of telamonioid species and e.g. some spore characteristics have often been overlooked. Our studies have concentrated on North Europe, but we have found some similarities with North European and North American taxa.

Population dynamics of blue mussels in a variable environment at the edge of their range

Spatial and temporal variation in the abundance of species can often be ascribed to spatial and temporal variation in the surrounding environment. Knowledge of how biotic and abiotic factors operate over different spatial and temporal scales in determining distribution, abundance, and structure of populations lies at the heart of ecology. The major part of the current ecological theory stems from studies carried out in central parts of the distributional range of species, whereas knowledge of how marginal populations function is inadequate. Understanding how marginal populations, living at the edge of their range, function is however in a key position to advance ecology and evolutionary biology as scientific disciplines. My thesis focuses on the factors affecting dynamics of marginal populations of blue mussels (Mytilus edulis) living close to their tolerance limits with regard to salinity. The thesis aims to highlight the dynamics at the edge of the range and contrast these with dynamics in more central parts of the range in order to understand the potential interplay between the central and the marginal part in the focal system. The objectives of the thesis are approached by studies on: (1) factors affecting regional patterns of the species, (2) long-term temporal dynamics of the focal species spaced along a regional salinity gradient, (3) selective predation by increasing populations of roach (Rutilus rutilus) when feeding on their main food item, the blue mussel, (4) the primary and secondary effects of local wave exposure gradients and (5) the role of small-scale habitat heterogeneity as determinants of large-scale pattern. The thesis shows that populations of blue mussels are largely determined by large scale changes in sea water salinity, affecting mainly recruitment success and longevity of local populations. In opposite to the traditional view, the thesis strongly indicate that vertebrate predators strongly affect abundance and size structure of blue mussel populations, and that the role of these predators increases towards the margin where populations are increasingly top-down controlled. The thesis also indicates that the positive role of biogenic habitat modifiers increases towards the marginal areas, where populations of blue mussels are largely recruitment limited. Finally, the thesis shows that local blue mussel populations are strongly dependent on high water turbulence, and therefore, dense populations are constrained to offshore habitats. Finally, the thesis suggests that ongoing sedimentation of rocky shores is detrimental for the species, affecting recruitment success and post-recruit survival, pushing stable mussel beds towards offshore areas. Ongoing large scale changes in the Baltic Sea, especially dilution processes with attendant effects, are predicted to substantially contract the distributional range of the mussel, but also affect more central populations. The thesis shows that in order to understand the functioning of marginal populations, research should (1) strive for multi-scale approaches in order to link ecosystem patterns with ecosystem processes, and (2) challenge the prevailing tenets that origin from research carried out in central areas that may not be valid at the edge.