Role of heat treatment in the processing and quality of oat flakes

This thesis reports on investigations into the influence of heat treatment on the manufacturing of oat flakes. Sources of variation in the oat flake quality are reviewed, including the whole chain from the farm to the consumer. The most important quality parameters of oat flakes are the absence of lipid hydrolysing enzymes, specific weight, thickness, breakage (fines), water absorption. Flavour, colour and pasting properties are also important, but were not included in the experimental part of this study. Of particular interest was the role of heat processing. The first possible heat treatment may occur already during grain drying, which in Finland generally happens at the farm. At the mill, oats are often kilned to stabilise the product by inactivating lipid hydrolysing enzymes. Almost invariably steaming is used during flaking, to soften the groats and reduce flake breakage. This thesis presents the use of a material science approach to investigating a complex system, typical of food processes. A combination of fundamental and empirical rheological measurements was used together with a laboratory scale process to simulate industrial processing. The results were verified by means of industrial trials. Industrially produced flakes at three thickness levels (nominally 0.75, 0.85 and 0.90 mm) were produced from kilned and unkilned oat groats, and the flake strength was measured at different moisture contents. Kilning was not found to significantly affect the force required to puncture a flake with a 2mm cylindrical probe, which was taken as a measure of flake strength. To further investigate how heat processing contributes to flake quality, dynamic mechanical analysis was used to characterise the effect of heat on the mechanical properties of oats. A marked stiffening of the groat, of up to about 50% increase in storage modulus, was observed during first heating at around 36 to 57°C. This was also observed in tablets prepared from ground groats and extracted oat starch. This stiffening was thus attributed to increased adhesion between starch granules. Groats were steamed in a laboratory steamer and were tempered in an oven at 80 110°C for 30 90 min. The maximum force required to compress the steamed groats to 50% strain increased from 50.7 N to 57.5 N as the tempering temperature was increased from 80 to 110°C. Tempering conditions also affected water absorption. A significantly higher moisture content was observed for kilned (18.9%) compared to unkilned (17.1%) groats, but otherwise had no effect on groat height, maximum force or final force after a 5 s relaxation time. Flakes were produced from the tempered groats using a laboratory flaking machine, using a roll gap of 0.4 mm. Apart from specific weight, flake properties were not influenced by kilning. Tempering conditions however had significant effects on the specific weight, thickness and water absorption of the flakes, as well as on the amount of fine material (<2 mm) produced during flaking. Flake strength correlated significantly with groat strength and flake thickness. Trial flaking at a commercial mill confirmed that groat temperature after tempering influenced water absorption. Variation in flake strength was observed , but at the groat temperatures required to inactivate lipase, it was rather small. Cold flaking of groats resulted in soft, floury flakes. The results presented in this thesis suggest that heating increased the adhesion between starch granules. This resulted in an increase in the stiffness and brittleness of the groat. Brittle fracture, rather than plastic flow, during flaking could result in flaws and cracks in the flake. These would be expected to increase water absorption. This was indeed observed as tempering temperature increased. Industrial trials, conducted with different groat temperatures, confirmed the main findings of the laboratory experiments. The approach used in the present study allowed the systematic study of the effect of interacting process parameters on product quality. There have been few scientific studies of oat processing, and these results can be used to understand the complex effects of process variables on flake quality. They also offer an insight into what happens as the oat groat is deformed into a flake.

Health-Related Quality of Life, Costs and Treatment of Inflammatory Rheumatic Diseases in Routine Practice : With special emphasis on biological drugs

Rheumatoid arthritis (RA) and other chronic inflammatory joint diseases already begin to affect patients health-related quality of life (HRQoL) in the earliest phases of these diseases. In treatment of inflammatory joint diseases, the last two decades have seen new strategies and treatment options introduced. Treatment is started at an earlier phase; combinations of disease-modifying anti-rheumatic drugs (DMARDs) and corticosteroids are used; and in refractory cases new drugs such as tumour necrosis factor (TNF) inhibitors or other biologicals can be started. In patients with new referrals to the Department of Rheumatology of the Helsinki University Central Hospital, we evaluated the 15D and the Stanford Health Assessment Questionnaire (HAQ) results at baseline and approximately 8 months after their first visit. Altogether the analysis included 295 patients with various rheumatic diseases. The mean baseline 15D score (0.822, SD 0.114) was significantly lower than for the age-matched general population (0.903, SD 0.098). Patients with osteoarthritis (OA) and spondyloarthropathies (SPA) reported the poorest HRQoL. In patients with RA and reactive arthritis (ReA) the HRQoL improved in a statistically significant manner during the 8-month follow-up. In addition, a clinically important change appeared in patients with systemic rheumatic diseases. HAQ score improved significantly in patients with RA, arthralgia and fibromyalgia, and ReA. In a study of 97 RA patients treated either with etanercept or adalimumab, we assessed their HRQoL with the RAND 36-Item Health Survey 1.0 (RAND-36) questionnaire. We also analysed changes in clinical parameters and the HAQ. With etanercept and adalimumab, the values of all domains in the RAND-36 questionnaire increased during the first 3 months. The efficacy of each in improving HRQoL was statistically significant, and the drug effects were comparable. Compared to Finnish age- and sex-matched general population values, the HRQoL of the RA patients was significantly lower at baseline and, despite the improvement, remained lower also at follow-up. Our RA patients had long-standing and severe disease that can explain the low HRQoL also at follow-up. In a pharmacoeconomic study of patients treated with infliximab we evaluated medical and work disability costs for patients with chronic inflammatory joint disease during one year before and one year after institution of infliximab treatment. Clinical and economic data for 96 patients with different arthritis diagnoses showed, in all patients, significantly improved clinical and laboratory variables. However, the medical costs increased significantly during the second period by 12 015 (95% confidence interval, 6 496 to 18 076). Only a minimal decrease in work disability costs occurred mean decrease 130 (-1 268 to 1 072). In a study involving a switch from infliximab to etanercept, we investigated the clinical outcome in 49 patients with RA. Reasons for switching were in 42% failure to respond by American College of Rheumatology (ACR) 50% criteria; in 12% adverse event; and in 46% non-medical reasons although the patients had responded to infliximab. The Disease Activity Score with 28 joints examined (DAS28) allowed us to measure patients disease activity and compare outcome between groups based on the reason for switching. In the patients in whom infliximab was switched to etanercept for nonmedical reasons, etanercept continued to suppress disease activity effectively, and 1-year drug survival for etanercept was 77% (95% CI, 62 to 97). In patients in the infliximab failure and adverse event groups, DAS28 values improved significantly during etanercept therapy. However, the 1-year drug survival of etanercept was only 43% (95% CI, 26 to 70) and 50% (95% CI, 33 to 100), respectively. Although the HRQoL of patients with inflammatory joint diseases is significantly lower than that of the general population, use of early and aggressive treatment strategies including TNF-inhibitors can improve patients HRQoL effectively. Further research is needed in finding new treatment strategies for those patients who fail to respond or lose their response to TNF-inhibitors.

Turbulent vertical fluxes and air quality measured in urban air in Helsinki

There is a growing need to understand the exchange processes of momentum, heat and mass between an urban surface and the atmosphere as they affect our quality of life. Understanding the source/sink strengths as well as the mixing mechanisms of air pollutants is particularly important due to their effects on human health and climate. This work aims to improve our understanding of these surface-atmosphere interactions based on the analysis of measurements carried out in Helsinki, Finland. The vertical exchange of momentum, heat, carbon dioxide (CO2) and aerosol particle number was measured with the eddy covariance technique at the urban measurement station SMEAR III, where the concentrations of ultrafine, accumulation mode and coarse particle numbers, nitrogen oxides (NOx), carbon monoxide (CO), ozone (O3) and sulphur dioxide (SO2) were also measured. These measurements were carried out over varying measurement periods between 2004 and 2008. In addition, black carbon mass concentration was measured at the Helsinki Metropolitan Area Council site during three campaigns in 1996-2005. Thus, the analyzed dataset covered far, the most comprehensive long-term measurements of turbulent fluxes reported in the literature from urban areas. Moreover, simultaneously measured urban air pollution concentrations and turbulent fluxes were examined for the first time. The complex measurement surrounding enabled us to study the effect of different urban covers on the exchange processes from a single point of measurement. The sensible and latent heat fluxes closely followed the intensity of solar radiation, and the sensible heat flux always exceeded the latent heat flux due to anthropogenic heat emissions and the conversion of solar radiation to direct heat in urban structures. This urban heat island effect was most evident during winter nights. The effect of land use cover was seen as increased sensible heat fluxes in more built-up areas than in areas with high vegetation cover. Both aerosol particle and CO2 exchanges were largely affected by road traffic, and the highest diurnal fluxes reached 109 m-2 s-1 and 20 µmol m-2 s-1, respectively, in the direction of the road. Local road traffic had the greatest effect on ultrafine particle concentrations, whereas meteorological variables were more important for accumulation mode and coarse particle concentrations. The measurement surroundings of the SMEAR III station served as a source for both particles and CO2, except in summer, when the vegetation uptake of CO2 exceeded the anthropogenic sources in the vegetation sector in daytime, and we observed a downward median flux of 8 µmol m-2 s-1. This work improved our understanding of the interactions between an urban surface and the atmosphere in a city located at high latitudes in a semi-continental climate. The results can be utilised in urban planning, as the fraction of vegetation cover and vehicular activity were found to be the major environmental drivers affecting most of the exchange processes. However, in order to understand these exchange and mixing processes on a city scale, more measurements above various urban surfaces accompanied by numerical modelling are required.

Sedimentary zooplankton remains as indicators of lake ecological quality and trophic structure

To protect and restore lake ecosystems under threats posed by the increasing human population, information on their ecological quality is needed. Lake sediments provide a data rich archive that allows identification of various biological components present prior to anthropogenic alterations as well as a constant record of changes. By providing a longer dimension of time than any ongoing monitoring programme, palaeolimnological methods can help in understanding natural variability and long-term ecological changes in lakes. As zooplankton have a central role in the lake food web, their remains can potentially provide versatile information on past trophic structure. However, various taphonomic processes operating in the lakes still raise questions concerning how subfossil assemblages reflect living communities. This thesis work aimed at improving the use of sedimentary zooplankton remains in the reconstruction of past zooplankton communities and the trophic structure in lakes. To quantify interspecific differences in the accumulation of remains, the subfossils of nine pelagic zooplankton taxa in annually laminated sediments were compared with monitoring results for live zooplankton in Lake Vesijärvi. This lake has a known history of eutrophication and recovery, which resulted from reduced external loading and effective fishing of plankti-benthivorous fish. The response of zooplankton assemblages to these known changes was resolved using annually laminated sediments. The generality of the responses observed in Lake Vesijärvi were further tested with a set of 31 lakes in Southern Finland, relating subfossils in surface sediments to contemporary water quality and fish density, as well as to lake morphometry. The results demonstrated differential preservation and retention of cladoceran species in the sediment. Daphnia, Diaphanosoma and Ceriodaphnia were clearly underrepresented in the sediment samples in comparison to well-preserved Bosmina species, Chydorus, Limnosida and Leptodora. For well-preserved species, the annual net accumulation rate was similar to or above the expected values, reflecting effective sediment focusing and accumulation in the deepest part of the lake. The decreased fish density and improved water quality led to subtle changes in zooplankton community composition. The abundance of Diaphanosoma and Limnosida increased after the reduction in fish density, while Ceriodaphnia and rotifers decreased. The most sensitive indicator of fish density was the mean size of Daphnia ephippia and Bosmina (E.) crassicornis ephippia and carapaces. The concentration of plant-associated species increased, reflecting expanding littoral vegetation along with increasing transparency. Several of the patterns observed in Lake Vesijärvi could also be found within the set of 31 lakes. According to this thesis work, the most useful cladoceran-based indices for nutrient status and planktivorous fish density in Finnish lakes were the relative abundances of certain pelagic taxa, and the mean size of Bosmina spp. carapaces, especially those of Bosmina (E.) cf. coregoni. The abundance of plant-associated species reflected the potential area for aquatic plants. Lake morphometry and sediment organic content, however, explained a relatively high proportion of the variance in the species data, and more studies are needed to quantify lake-specific differences in the accumulation and preservation of remains. Commonly occurring multicollinearity between environmental variables obstructs the cladoceran-based reconstruction of single environmental variables. As taphonomic factors and several direct and indirect structuring forces in lake ecosystems simultaneously affect zooplankton, the subfossil assemblages should be studied in a holistic way before making final conclusions about the trophic structure and the change in lake ecological quality.

Interest in university studies : Its role and relation to other motivational variables

This dissertation empirically explored interest as a motivational force in university studies, including the role it currently plays and possible ways of enhancing this role as a student motivator. The general research questions were as follows: 1) What role does interest play in university studies? 2) What explains academic success if studying is not based on interest? 3) How do different learning environments support or impede interest-based studying? Four empirical studies addressed these questions. Study 1 (n=536) compared first-year students explanations of their disciplinary choices in three fields: veterinary medicine, humanities and law. Study 2 (n=28) focused on the role of individual interest in the humanities and veterinary medicine, fields which are very different from each other as regards their nature of studying. Study 3 (n=52) explored veterinary students motivation and study practices in relation to their study success. Study 4 (n=16) explored veterinary students interest experience in individual lectures on a daily basis. By comparing different fields and focusing on one study field in more detail, it was possible to obtain a many-sided picture of the role of interest in different learning environments. Questionnaires and quantitative methods have often been used to measure interest in academic learning. The present work is based mostly on qualitative data, and qualitative methods were applied to add to the previous research. Study 1 explored students open-ended answers, and these provided a basis for the interviews in Study 2. Study 3 explored veterinary students portfolios in a longitudinal setting. For Study 4, a diary including both qualitative and quantitative measures was designed to capture veterinary students interest experience. Qualitative content analysis was applied in all four studies, but quantitative analyses were also added. The thesis showed that university students often explain their disciplinary choices in terms of interest. Because interest is related to high-quality learning, the students seemed to have a good foundation for successful studies. However, the learning environments did not always support interest-based studying; Time-management and coping skills were found to be more important than interest in terms of study success. The results also indicated that interest is not the only motivational variable behind university studies. For example, future goals are needed in order to complete a degree. Even so, the results clearly indicated that it would be worth supporting interest-based studying both in professionally and generally oriented study fields. This support is important not only to promote high-quality learning but also meaningful studying, student well-being, and life-long learning.