Use of biomass fuels in the brick-making industries of Sudan: Implications for deforestation and greenhouse gas emission

The study focuses on the potential roles of the brick making industries in Sudan in deforestation and greenhouse gas emission due to the consumption of biofuels. The results were based on the observation of 25 brick making industries from three administrative regions in Sudan namely, Khartoum, Kassala and Gezira. The methodological approach followed the procedures outlined by the Intergovernmental Panel on Climate Change (IPCC). For predicting a serious deforestation scenario, it was also assumed that all of wood use for this particular purpose is from unsustainable sources. The study revealed that the total annual quantity of fuelwood consumed by the surveyed brick making industries (25) was 2,381 t dm. Accordingly, the observed total potential deforested wood was 10,624 m3, in which the total deforested round wood was 3,664 m3 and deforested branches was 6,961 m3. The study observed that a total of 2,990 t biomass fuels (fuelwood and dung cake) consumed annually by the surveyed brick making industries for brick burning. Consequently, estimated total annual emissions of greenhouse gases were 4,832 t CO2, 21 t CH4, 184 t CO, 0.15 t N20, 5 t NOX and 3.5 t NO while the total carbon released in the atmosphere was 1,318 t. Altogether, the total annual greenhouse gases emissions from biomass fuels burning was 5,046 t; of which 4,104 t from fuelwood and 943 t from dung cake burning. According to the results, due to the consumption of fuelwood in the brick making industries (3,450 units) of Sudan, the amount of wood lost from the total growing stock of wood in forests and trees in Sudan annually would be 1,466,000 m3 encompassing 505,000 m3 round wood and 961,000 m3 branches annually. By considering all categories of biofuels (fuelwood and dung cake), it was estimated that, the total emissions from all the brick making industries of Sudan would be 663,000 t CO2, 2,900 t CH4, 25,300 t CO, 20 t N2O, 720 t NOX and 470 t NO per annum, while the total carbon released in the atmosphere would be 181,000 t annually.

Use of non-specific and specific interactions in the analysis of testosterone and related compounds by capillary electromigration techniques

Determination of testosterone and related compounds in body fluids is of utmost importance in doping control and the diagnosis of many diseases. Capillary electromigration techniques are a relatively new approach for steroid research. Owing to their electrical neutrality, however, separation of steroids by capillary electromigration techniques requires the use of charged electrolyte additives that interact with the steroids either specifically or non-specifically. The analysis of testosterone and related steroids by non-specific micellar electrokinetic chromatography (MEKC) was investigated in this study. The partial filling (PF) technique was employed, being suitable for detection by both ultraviolet spectrophotometry (UV) and electrospray ionization mass spectrometry (ESI-MS). Efficient, quantitative PF-MEKC UV methods for steroid standards were developed through the use of optimized pseudostationary phases comprising surfactants and cyclodextrins. PF-MEKC UV proved to be a more sensitive, efficient and repeatable method for the steroids than PF-MEKC ESI-MS. It was discovered that in PF-MEKC analyses of electrically neutral steroids, ESI-MS interfacing sets significant limitations not only on the chemistry affecting the ionization and detection processes, but also on the separation. The new PF-MEKC UV method was successfully employed in the determination of testosterone in male urine samples after microscale immunoaffinity solid-phase extraction (IA-SPE). The IA-SPE method, relying on specific interactions between testosterone and a recombinant anti-testosterone Fab fragment, is the first such method described for testosterone. Finally, new data for interactions between steroids and human and bovine serum albumins were obtained through the use of affinity capillary electrophoresis. A new algorithm for the calculation of association constants between proteins and neutral ligands is introduced.

Forest inventory-based large-scale forest biomass and carbon budget assessment: new enhanced methods and use of remote sensing for verification

In recent years, concern has arisen over the effects of increasing carbon dioxide (CO2) in the earth's atmosphere due to the burning of fossil fuels. One way to mitigate increase in atmospheric CO2 concentration and climate change is carbon sequestration to forest vegeta-tion through photosynthesis. Comparable regional scale estimates for the carbon balance of forests are therefore needed for scientific and political purposes. The aim of the present dissertation was to improve methods for quantifying and verifying inventory-based carbon pool estimates of the boreal forests in the mineral soils. Ongoing forest inventories provide a data based on statistically sounded sampling for estimating the level of carbon stocks and stock changes, but improved modelling tools and comparison of methods are still needed. In this dissertation, the entire inventory-based large-scale forest carbon stock assessment method was presented together with some separate methods for enhancing and comparing it. The enhancement methods presented here include ways to quantify the biomass of understorey vegetation as well as to estimate the litter production of needles and branches. In addition, the optical remote sensing method illustrated in this dis-sertation can be used to compare with independent data. The forest inventory-based large-scale carbon stock assessment method demonstrated here provided reliable carbon estimates when compared with independent data. Future ac-tivity to improve the accuracy of this method could consist of reducing the uncertainties regarding belowground biomass and litter production as well as the soil compartment. The methods developed will serve the needs for UNFCCC reporting and the reporting under the Kyoto Protocol. This method is principally intended for analysts or planners interested in quantifying carbon over extensive forest areas.

Geological factors affecting on after-use of Finnish cut-over peatlands : with implications on the carbon accumulation

In Finland, peat harvesting sites are utilized down almost to the mineral soil. In this situation the properties of mineral subsoil are likely to have considerable influence on the suitability for the various after-use forms. The aims of this study were to recognize the chemical and physical properties of mineral subsoils possibly limiting the after-use of cut-over peatlands, to define a minimum practice for mineral subsoil studies and to describe the role of different geological areas. The future percentages of the different after-use forms were predicted, which made it possible to predict also carbon accumulation in this future situation. Mineral subsoils of 54 different peat production areas were studied. Their general features and grain size distribution was analysed. Other general items studied were pH, electrical conductivity, organic matter, water soluble nutrients (P, NO3-N, NH4-N, S and Fe) and exchangeable nutrients (Ca, Mg and K). In some cases also other elements were analysed. In an additional case study carbon accumulation effectiveness before the intervention was evaluated on three sites in Oulu area (representing sites typically considered for peat production). Areas with relatively sulphur rich mineral subsoil and pool-forming areas with very fine and compact mineral subsoil together covered approximately 1/5 of all areas. These areas were unsuitable for commercial use. They were recommended for example for mire regeneration. Another approximate 1/5 of the areas included very coarse or very fine sediments. Commercial use of these areas would demand special techniques - like using the remaining peat layer for compensating properties missing from the mineral subsoil. One after-use form was seldom suitable for one whole released peat production area. Three typical distribution patterns (models) of different mineral subsoils within individual peatlands were found. 57 % of studied cut-over peatlands were well suited for forestry. In a conservative calculation 26% of the areas were clearly suitable for agriculture, horticulture or energy crop production. If till without large boulders was included, the percentage of areas suitable to field crop production would be 42 %. 9-14 % of all areas were well suitable for mire regeneration or bird sanctuaries, but all areas were considered possible for mire regeneration with correct techniques. Also another 11 % was recommended for mire regeneration to avoid disturbing the mineral subsoil, so total 20-25 % of the areas would be used for rewetting. High sulphur concentrations and acidity were typical to the areas below the highest shoreline of the ancient Litorina sea and Lake Ladoga Bothnian Bay zone. Also differences related to nutrition were detected. In coarse sediments natural nutrient concentration was clearly higher in Lake Ladoga Bothnian Bay zone and in the areas of Svecokarelian schists and gneisses, than in Granitoid area of central Finland and in Archaean gneiss areas. Based on this study the recommended minimum analysis for after-use planning was for pH, sulphur content and fine material (<0.06 mm) percentage. Nutrition capacity could be analysed using the natural concentrations of calcium, magnesium and potassium. Carbon accumulation scenarios were developed based on the land-use predictions. These scenarios were calculated for areas in peat production and the areas released from peat production (59300 ha + 15 671 ha). Carbon accumulation of the scenarios varied between 0.074 and 0.152 million t C a-1. In the three peatlands considered for peat production the long term carbon accumulation rates varied between 13 and 24 g C m-2 a-1. The natural annual carbon accumulation had been decreasing towards the time of possible intervention.

Use of ecological information in urban planning

Urbanization leads to irreversible land-use change, which has ecological consequences such as the loss and fragmentation of green areas, and structural and functional changes in terrestrial and aquatic ecosystems. These consequences diminish ecosystem services important for human populations living in urban areas. All this results in a conflict situation: how to simultaneously meet the needs of city growth and the principles of sustainable development, and especially conserve important green areas within and around built-up areas? Urban planners and decisionmakers have an important role in this, since they must use the ecological information mainly from species and biotope inventories and biodiversity impact assessments in determining the conservation values of green areas. The main aim of this thesis was to study the use of ecological information in the urban land-use planning and decisionmaking process in the Helsinki Metropolitan Area, Finland. At first, the literature on ecological-social systems linkages related to urban planning was reviewed. Based on the review, a theoretical and conceptual framework for the research on Finnish urban setting was adapted. Secondly, factors determining the importance and effectiveness of incorporation of ecological information into the urban planning process, and the challenges related to the use of ecological information were studied. Thirdly, the importance and use of Local Ecological Knowledge in urban planning were investigated. Then, factors determining the consideration of urban green areas and related ecological information in political land-use decisionmaking were studied. Finally, in a case study illustrating the above considerations, the importance of urban stream ecosystems in the land-use planning was investigated. This thesis demonstrated that although there are several challenges in using ecological information effectively, it is considered as an increasingly important part of the basic information used in urban planning and decisionmaking process. The basic determinants for this are the recent changes in environmental legislation, but also the increasing appreciation of green areas and their conservation values by all the stakeholders. In addition, Local Ecological Knowledge in its several forms can be a source of ecological information for planners if incorporated effectively into the process. This study also showed that rare or endangered species and biotopes, and related ecological information receive priority in the urban planning process and usually pass through the decisionmaking system. Furthermore, the stream Rekolanoja case indicates that planners and residents see the value of urban stream ecosystem as increasingly important for the local health and social values, such as recreation and stress relief.

Invasive pneumococcal infections in Finland before routine use of conjugate vaccines : opportunities for prevention

Streptococcus pneumoniae is a leading cause of pneumonia, meningitis and bacteremia worldwide. The 23-valent pneumococcal polysaccharide vaccine (PPV23) is recommended for adults less than 65 years old with certain chronic medical conditions and for all elderly persons because of high rates of invasive pneumococcal infections (IPI) and increased risk of death. This study provides a comprehensive picture of the epidemiology of pneumococcal infections in Finland before the introduction of childhood pneumococcal conjugate vaccines, focusing on disease rates, risk factors, clinical outcome, and healthcare associated infections. This study was based on national, population-based laboratory surveillance for IPI. Information on all episodes of IPI was collected from the primary diagnostic laboratory. A case with IPI was defined as the isolation of S. pneumoniae from blood or cerebrospinal fluid during 1995-2002. Information on comorbidities and underlying conditions for IPI patients was obtained by linking the IPI surveillance database to other national, population-based health registries using each patient’s unique national identity code. In total, 4357 cases of IPI were identified. The overall annualized IPI incidence increased by 35% during the study period and was 10.6 per 100 000 population. The temporal increase in disease rates was associated with higher blood culturing rates over time. In working age adults, two-thirds of severe infections and one half of fatal cases occurred in persons with no recognized PPV23 indication. Persons with asthma were at increased risk for IPI and this new risk factor accounted for 5% of the overall disease burden. One tenth of pneumococcal bacteremias were healthcare-associated, and mortality among these patients was over twice as high as among patients with community-associated bacteremia. Most patients with nosocomial infections had underlying conditions for which PPV23 is recommended. The incidence of IPI in Finland has increased and the overall disease burden is higher than previously reported. The findings of this study underscore the urgent need for improved prevention efforts against pneumococcal infections in Finland through increased use of PPV23 in adult risk groups and introduction of childhood immunization with pneumococcal conjugate vaccine.

Towards the Use of Radar Winds in Numerical Weather Prediction

Numerical weather prediction (NWP) models provide the basis for weather forecasting by simulating the evolution of the atmospheric state. A good forecast requires that the initial state of the atmosphere is known accurately, and that the NWP model is a realistic representation of the atmosphere. Data assimilation methods are used to produce initial conditions for NWP models. The NWP model background field, typically a short-range forecast, is updated with observations in a statistically optimal way. The objective in this thesis has been to develope methods in order to allow data assimilation of Doppler radar radial wind observations. The work has been carried out in the High Resolution Limited Area Model (HIRLAM) 3-dimensional variational data assimilation framework. Observation modelling is a key element in exploiting indirect observations of the model variables. In the radar radial wind observation modelling, the vertical model wind profile is interpolated to the observation location, and the projection of the model wind vector on the radar pulse path is calculated. The vertical broadening of the radar pulse volume, and the bending of the radar pulse path due to atmospheric conditions are taken into account. Radar radial wind observations are modelled within observation errors which consist of instrumental, modelling, and representativeness errors. Systematic and random modelling errors can be minimized by accurate observation modelling. The impact of the random part of the instrumental and representativeness errors can be decreased by calculating spatial averages from the raw observations. Model experiments indicate that the spatial averaging clearly improves the fit of the radial wind observations to the model in terms of observation minus model background (OmB) standard deviation. Monitoring the quality of the observations is an important aspect, especially when a new observation type is introduced into a data assimilation system. Calculating the bias for radial wind observations in a conventional way can result in zero even in case there are systematic differences in the wind speed and/or direction. A bias estimation method designed for this observation type is introduced in the thesis. Doppler radar radial wind observation modelling, together with the bias estimation method, enables the exploitation of the radial wind observations also for NWP model validation. The one-month model experiments performed with the HIRLAM model versions differing only in a surface stress parameterization detail indicate that the use of radar wind observations in NWP model validation is very beneficial.

Species-specific and Indication-based Use of Antimicrobials in Dogs, Cats, Cattle and Horses in Finland : Data collected using three different methods

Increasing antimicrobial resistance in bacteria has led to the need for better understanding of antimicrobial usage patterns. In 1999, the World Organisation for Animal Health (OIE) recommended that an international ad hoc group should be established to address human and animal health risks related to antimicrobial resistance and the contribution of antimicrobial usage in veterinary medicine. In European countries the need for continuous recording of the usage of veterinary antimicrobials as well as for animal species-specific and indication-based data on usage has been acknowledged. Finland has been among the first countries to develop prudent use guidelines in veterinary medicine, as the Ministry of Agriculture and Forestry issued the first animal species-specific indication-based recommendations for antimicrobial use in animals in 1996. These guidelines have been revised in 2003 and 2009. However, surveillance on the species-specific use of antimicrobials in animals has not been performed in Finland. This thesis provides animal species-specific information on indication-based antimicrobial usage. Different methods for data collection have been utilized. Information on antimicrobial usage in animals has been gathered in four studies (studies A-D). Material from studies A, B and C have been used in an overlapping manner in the original publications I-IV. Study A (original publications I & IV) presents a retrospective cross-sectional survey on prescriptions for small animals at the Veterinary Teaching Hospital of the University of Helsinki. Prescriptions for antimicrobial agents (n = 2281) were collected and usage patterns, such as the indication and length of treatment, were reviewed. Most of the prescriptions were for dogs (78%), and primarily for the treatment of skin and ear infections most of which were treated with cephalexin for a median period of 14 days. Prescriptions for cats (18%) were most often for the treatment of urinary tract infections with amoxicillin for a median length of 10 days. Study B (original publication II) was a retrospective cross-sectional survey where prescriptions for animals were collected from 17 University Pharmacies nationwide. Antimicrobial prescriptions (n = 1038) for mainly dogs (65%) and cats (19%) were investigated. In this study, cephalexin and amoxicillin were also the most frequently used drugs for dogs and cats, respectively. In study C (original publications III & IV), the indication-based usage of antimicrobials of practicing veterinarians was analyzed by using a prospective questionnaire. Randomly selected practicing veterinarians in Finland (n = 262) recorded all their antimicrobial usage during a 7-day study period. Cattle (46%) with mastitis were the most common patients receiving antimicrobial treatment, generally intramuscular penicillin G or intramammary treatment with ampicillin and cloxacillin. The median length of treatment was four days, regardless of the route of administration. Antimicrobial use in horses was evaluated in study D, the results of which are previously unpublished. Firstly, data collected with the prospective questionnaire from the practicing veterinarians showed that horses (n = 89) were frequently treated for skin or wound infections by using penicillin G or trimethoprim-sulfadiazine. The mean duration of treatment was five to seven days. Secondly, according to retrospective data collected from patient records, horses (n = 74) that underwent colic surgery at the Veterinary Teaching Hospital of the University of Helsinki were generally treated according to national and hospital recommendations; penicillin G and gentamicin was administered preoperatively and treatment was continued for a median of three days postoperatively. In conclusion, Finnish veterinarians followed well the national prudent use guidelines. Narrow-spectrum antimicrobials were preferred and, for instance, fluoroquinolones were used sparingly. Prescription studies seemed to give good information on antimicrobials usage, especially when combined with complementary information from patient records. A prospective questionnaire study provided a fair amount of valuable data on several animal species. Electronic surveys are worthwhile exploiting in the future.

Future chemistry teachers use of knowledge dimensions and high-order cognitive skills in pre-laboratory concept maps

This poster describes a pilot case study, which aim is to study how future chemistry teachers use knowledge dimensions and high-order cognitive skills (HOCS) in their pre-laboratory concept maps to support chemistry laboratory work. The research data consisted of 168 pre-laboratory concept maps that 29 students constructed as a part of their chemistry laboratory studies. Concept maps were analyzed by using a theory based content analysis through Anderson & Krathwohls' learning taxonomy (2001). This study implicates that novice concept mapper students use all knowledge dimensions and applying, analyzing and evaluating HOCS to support the pre-laboratory work.

Use of Standards for CAD Layers in Building

One of the central issues in making efficient use of IT in the design, construction and maintenance of buildings is the sharing of the digital building data across disciplines and lifecycle stages. One technology which enables data sharing is CAD layering, which to be of real use requires the definition of standards. This paper focuses on the background, objectives and effectiveness of the International standard ISO 13567, Organisation and naming of layers for CAD. In particular the efficiency and effectiveness of the standardisation and standard implementation process are in focus, rather than the technical details. The study was conducted as a qualitative study with a number of experts who responded to a semi-structured mail questionnaire, supplemented by personal interviews. The main results were that CAD layer standards based on the ISO standard have been implemented, particularly in northern European countries, but are not very widely used. A major problem which was identified was the lack of resources for marketing and implementing the standard as national variations, once it had been formally accepted.