Process Analytical Technology Approach on Fluid Bed Granulation and Drying : Identifying Critical Relationships and Constructing the Design Space

Fluid bed granulation is a key pharmaceutical process which improves many of the powder properties for tablet compression. Dry mixing, wetting and drying phases are included in the fluid bed granulation process. Granules of high quality can be obtained by understanding and controlling the critical process parameters by timely measurements. Physical process measurements and particle size data of a fluid bed granulator that are analysed in an integrated manner are included in process analytical technologies (PAT). Recent regulatory guidelines strongly encourage the pharmaceutical industry to apply scientific and risk management approaches to the development of a product and its manufacturing process. The aim of this study was to utilise PAT tools to increase the process understanding of fluid bed granulation and drying. Inlet air humidity levels and granulation liquid feed affect powder moisture during fluid bed granulation. Moisture influences on many process, granule and tablet qualities. The approach in this thesis was to identify sources of variation that are mainly related to moisture. The aim was to determine correlations and relationships, and utilise the PAT and design space concepts for the fluid bed granulation and drying. Monitoring the material behaviour in a fluidised bed has traditionally relied on the observational ability and experience of an operator. There has been a lack of good criteria for characterising material behaviour during spraying and drying phases, even though the entire performance of a process and end product quality are dependent on it. The granules were produced in an instrumented bench-scale Glatt WSG5 fluid bed granulator. The effect of inlet air humidity and granulation liquid feed on the temperature measurements at different locations of a fluid bed granulator system were determined. This revealed dynamic changes in the measurements and enabled finding the most optimal sites for process control. The moisture originating from the granulation liquid and inlet air affected the temperature of the mass and pressure difference over granules. Moreover, the effects of inlet air humidity and granulation liquid feed rate on granule size were evaluated and compensatory techniques used to optimize particle size. Various end-point indication techniques of drying were compared. The ∆T method, which is based on thermodynamic principles, eliminated the effects of humidity variations and resulted in the most precise estimation of the drying end-point. The influence of fluidisation behaviour on drying end-point detection was determined. The feasibility of the ∆T method and thus the similarities of end-point moisture contents were found to be dependent on the variation in fluidisation between manufacturing batches. A novel parameter that describes behaviour of material in a fluid bed was developed. Flow rate of the process air and turbine fan speed were used to calculate this parameter and it was compared to the fluidisation behaviour and the particle size results. The design space process trajectories for smooth fluidisation based on the fluidisation parameters were determined. With this design space it is possible to avoid excessive fluidisation and improper fluidisation and bed collapse. Furthermore, various process phenomena and failure modes were observed with the in-line particle size analyser. Both rapid increase and a decrease in granule size could be monitored in a timely manner. The fluidisation parameter and the pressure difference over filters were also discovered to express particle size when the granules had been formed. The various physical parameters evaluated in this thesis give valuable information of fluid bed process performance and increase the process understanding.

Information, risk and trust in the food chain : Ex-ante valuation of consumer willingness to pay for beef quality information using the contingent valuation method

The safety of food has become an increasingly interesting issue to consumers and the media. It has also become a source of concern, as the amount of information on the risks related to food safety continues to expand. Today, risk and safety are permanent elements within the concept of food quality. Safety, in particular, is the attribute that consumers find very difficult to assess. The literature in this study consists of three main themes: traceability; consumer behaviour related to both quality and safety issues and perception of risk; and valuation methods. The empirical scope of the study was restricted to beef, because the beef labelling system enables reliable tracing of the origin of beef, as well as attributes related to safety, environmental friendliness and animal welfare. The purpose of this study was to examine what kind of information flows are required to ensure quality and safety in the food chain for beef, and who should produce that information. Studying the willingness to pay of consumers makes it possible to determine whether the consumers consider the quantity of information available on the safety and quality of beef sufficient. One of the main findings of this study was that the majority of Finnish consumers (73%) regard increased quality information as beneficial. These benefits were assessed using the contingent valuation method. The results showed that those who were willing to pay for increased information on the quality and safety of beef would accept an average price increase of 24% per kilogram. The results showed that certain risk factors impact consumer willingness to pay. If the respondents considered genetic modification of food or foodborne zoonotic diseases as harmful or extremely harmful risk factors in food, they were more likely to be willing to pay for quality information. The results produced by the models thus confirmed the premise that certain food-related risks affect willingness to pay for beef quality information. The results also showed that safety-related quality cues are significant to the consumers. In the first place, the consumers would like to receive information on the control of zoonotic diseases that are contagious to humans. Similarly, other process-control related information ranked high among the top responses. Information on any potential genetic modification was also considered important, even though genetic modification was not regarded as a high risk factor.

New approaches to improve the cord blood unit hematopoietic progenitor cell content

Cord blood is a well-established alternative to bone marrow and peripheral blood stem cell transplantation. To this day, over 400 000 unrelated donor cord blood units have been stored in cord blood banks worldwide. To enable successful cord blood transplantation, recent efforts have been focused on finding ways to increase the hematopoietic progenitor cell content of cord blood units. In this study, factors that may improve the selection and quality of cord blood collections for banking were identified. In 167 consecutive cord blood units collected from healthy full-term neonates and processed at a national cord blood bank, mean platelet volume (MPV) correlated with the numbers of cord blood unit hematopoietic progenitors (CD34+ cells and colony-forming units); this is a novel finding. Mean platelet volume can be thought to represent general hematopoietic activity, as newly formed platelets have been reported to be large. Stress during delivery is hypothesized to lead to the mobilization of hematopoietic progenitor cells through cytokine stimulation. Accordingly, low-normal umbilical arterial pH, thought to be associated with perinatal stress, correlated with high cord blood unit CD34+ cell and colony-forming unit numbers. The associations were closer in vaginal deliveries than in Cesarean sections. Vaginal delivery entails specific physiological changes, which may also affect the hematopoietic system. Thus, different factors may predict cord blood hematopoietic progenitor cell numbers in the two modes of delivery. Theoretical models were created to enable the use of platelet characteristics (mean platelet volume) and perinatal factors (umbilical arterial pH and placental weight) in the selection of cord blood collections with high hematopoietic progenitor cell counts. These observations could thus be implemented as a part of the evaluation of cord blood collections for banking. The quality of cord blood units has been the focus of several recent studies. However, hemostasis activation during cord blood collection is scarcely evaluated in cord blood banks. In this study, hemostasis activation was assessed with prothrombin activation fragment 1+2 (F1+2), a direct indicator of thrombin generation, and platelet factor 4 (PF4), indicating platelet activation. Altogether three sample series were collected during the set-up of the cord blood bank as well as after changes in personnel and collection equipment. The activation decreased from the first to the subsequent series, which were collected with the bank fully in operation and following international standards, and was at a level similar to that previously reported for healthy neonates. As hemostasis activation may have unwanted effects on cord blood cell contents, it should be minimized. The assessment of hemostasis activation could be implemented as a part of process control in cord blood banks. Culture assays provide information about the hematopoietic potential of the cord blood unit. In processed cord blood units prior to freezing, megakaryocytic colony growth was evaluated in semisolid cultures with a novel scoring system. Three investigators analyzed the colony assays, and the scores were highly concordant. With such scoring systems, the growth potential of various cord blood cell lineages can be assessed. In addition, erythroid cells were observed in liquid cultures of cryostored and thawed, unseparated cord blood units without exogenous erythropoietin. This was hypothesized to be due to the erythropoietic effect of thrombopoietin, endogenous erythropoietin production, and diverse cell-cell interactions in the culture. This observation underscores the complex interactions of cytokines and supporting cells in the heterogeneous cell population of the thawed cord blood unit.

Investigating physical properties of solid dosage forms during pharmaceutical processing : Process analytical applications of vibrational spectroscopy

In order to improve and continuously develop the quality of pharmaceutical products, the process analytical technology (PAT) framework has been adopted by the US Food and Drug Administration. One of the aims of PAT is to identify critical process parameters and their effect on the quality of the final product. Real time analysis of the process data enables better control of the processes to obtain a high quality product. The main purpose of this work was to monitor crucial pharmaceutical unit operations (from blending to coating) and to examine the effect of processing on solid-state transformations and physical properties. The tools used were near-infrared (NIR) and Raman spectroscopy combined with multivariate data analysis, as well as X-ray powder diffraction (XRPD) and terahertz pulsed imaging (TPI). To detect process-induced transformations in active pharmaceutical ingredients (APIs), samples were taken after blending, granulation, extrusion, spheronisation, and drying. These samples were monitored by XRPD, Raman, and NIR spectroscopy showing hydrate formation in the case of theophylline and nitrofurantoin. For erythromycin dihydrate formation of the isomorphic dehydrate was critical. Thus, the main focus was on the drying process. NIR spectroscopy was applied in-line during a fluid-bed drying process. Multivariate data analysis (principal component analysis) enabled detection of the dehydrate formation at temperatures above 45°C. Furthermore, a small-scale rotating plate device was tested to provide an insight into film coating. The process was monitored using NIR spectroscopy. A calibration model, using partial least squares regression, was set up and applied to data obtained by in-line NIR measurements of a coating drum process. The predicted coating thickness agreed with the measured coating thickness. For investigating the quality of film coatings TPI was used to create a 3-D image of a coated tablet. With this technique it was possible to determine coating layer thickness, distribution, reproducibility, and uniformity. In addition, it was possible to localise defects of either the coating or the tablet. It can be concluded from this work that the applied techniques increased the understanding of physico-chemical properties of drugs and drug products during and after processing. They additionally provided useful information to improve and verify the quality of pharmaceutical dosage forms

The Reorganisation of Provincial Territories in Light of the Imperial Decision-Making Process : Later Roman Arabia and Tres Palaestinae as Case Studies

The dissertation examines Roman provincial administration and the phenomenon of territorial reorganisations of provinces during the Imperial period with special emphasis on the provinces of Arabia and Palaestina during the Later Roman period, i.e., from Diocletian (r. 284 305) to the accession of Phocas (602), in the light of imperial decision-making. Provinces were the basic unit of Roman rule, for centuries the only level of administration that existed between the emperor and the cities of the Empire. The significance of the territorial reorganisations that the provinces were subjected to during the Imperial period is thus of special interest. The approach to the phenomenon is threefold: firstly, attention is paid to the nature and constraints of the Roman system of provincial administration. Secondly, the phenomenon of territorial reorganisations is analysed on the macro-scale, and thirdly, a case study concerning the reorganisations of the provinces of Arabia and Palaestina is conducted. The study of the mechanisms of decision-making provides a foundation through which the collected data of all known major territorial reorganisations is interpreted. The data concerning reorganisations is also subjected to qualitative comparative analysis that provides a new perspective to the data in the form of statistical analysis that is sensitive to the complexities of individual cases. This analysis of imperial decision-making is based on a timeframe stretching from Augustus (r. 30 BC AD 14) to the accession of Phocas (602). The study identifies five distinct phases in the use of territorial reorganisations of the provinces. From Diocletian s reign there is a clear normative change that made territorial reorganisations a regular tool of administration for the decision-making elite for addressing a wide variety of qualitatively different concerns. From the beginning of the fifth century the use of territorial reorganisations rapidly diminishes. The two primary reasons for the decline in the use of reorganisations were the solidification of ecclesiastical power and interests connected to the extent of provinces, and the decline of the dioceses. The case study of Palaestina and Arabia identifies seven different territorial reorganisations from Diocletian to Phocas. Their existence not only testifies to wider imperial policies, but also shows sensitivity to local conditions and corresponds with the general picture of provincial reorganisations. The territorial reorganisations of the provinces reflect the proactive control of the Roman decision-making elite. The importance of reorganisations should be recognised more clearly as part of the normal imperial administration of the provinces and especially reflecting the functioning of dioceses.

Lagöversättning som process och produkt : Revideringar och institutioner vid lagöversättning till svenska i Finland

The thesis studies the translation process for the laws of Finland as they are translated from Finnish into Swedish. The focus is on revision practices, norms and workplace procedures. The translation process studied covers three institutions and four revisions. In three separate studies the translation process is analyzed from the perspective of the translations, the institutions and the actors. The general theoretical framework is Descriptive Translation Studies. For the analysis of revisions made in versions of the Swedish translation of Finnish laws, a model is developed covering five grammatical categories (textual revisions, syntactic revisions, lexical revisions, morphological revisions and content revisions) and four norms (legal adequacy, correct translation, correct language and readability). A separate questionnaire-based study was carried out with translators and revisers at the three institutions. The results show that the number of revisions does not decrease during the translation process, and no division of labour can be seen at the different stages. This is somewhat surprising if the revision process is regarded as one of quality control. Instead, all revisers make revisions on every level of the text. Further, the revisions do not necessarily imply errors in the translations but are often the result of revisers following different norms for legal translation. The informal structure of the institutions and its impact on communication, visibility and workplace practices was studied from the perspective of organization theory. The results show weaknesses in the communicative situation, which affect the co-operation both between institutions and individuals. Individual attitudes towards norms and their relative authority also vary, in the sense that revisers largely prioritize legal adequacy whereas translators give linguistic norms a higher value. Further, multi-professional teamwork in the institutions studied shows a kind of teamwork based on individuals and institutions doing specific tasks with only little contact with others. This shows that the established definitions of teamwork, with people co-working in close contact with each other, cannot directly be applied to the workplace procedures in the translation process studied. Three new concepts are introduced: flerstegsrevidering (multi-stage revision), revideringskedja (revision chain) and normsyn (norm attitude). The study seeks to make a contribution to our knowledge of legal translation, translation processes, institutional translation, revision practices and translation norms for legal translation. Keywords: legal translation, translation of laws, institutional translation, revision, revision practices, norms, teamwork, organizational informal structure, translation process, translation sociology, multilingual.

Variation in tracheid cross-sectional dimensions and wood viscoelasticity extent and control methods

Printing papers have been the main product of the Finnish paper industry. To improve properties and economy of printing papers, controlling of tracheid cross-sectional dimensions and wood viscoelasticity are examined in this study. Controlling is understood as any procedure which yields raw material classes with distinct properties and small internal variation. Tracheid cross-sectional dimensions, i.e., cell wall thickness and radial and tangential diameters can be controlled with methods such as sorting wood into pulpwood and sawmill chips, sorting of logs according to tree social status and fractionation of fibres. These control methods were analysed in this study with simulations, which were based on measured tracheid cross-sectional dimensions. A SilviScan device was used to measure the data set from five Norway spruce (Picea abies) and five Scots pine (Pinus sylvestris) trunks. The simulation results indicate that the sawmill chips and top pulpwood assortments have quite similar cross-sectional dimensions. Norway spruce and Scots pine are on average also relatively similar in their cross-sectional dimensions. The distributions of these species are somewhat different, but from a practical point of view, the differences are probably of minor importance. The controlling of tracheid cross-sectional dimensions can be done most efficiently with methods that can separate fibres into earlywood and latewood. Sorting of logs or partitioning of logs into juvenile and mature wood were markedly less efficient control methods than fractionation of fibres. Wood viscoelasticity affects energy consumption in mechanical pulping, and is thus an interesting control target when improving energy efficiency of the process. A literature study was made to evaluate the possibility of using viscoelasticity in controlling. The study indicates that there is considerable variation in viscoelastic properties within tree species, but unfortunately, the viscoelastic properties of important raw material lots such as top pulpwood or sawmill chips are not known. Viscoelastic properties of wood depend mainly on lignin, but also on microfibrillar angle, width of cellulose crystals and tracheid cross-sectional dimensions.

Microbial diversity in the municipal composting process and development of detection methods

Composting refers to aerobic degradation of organic material and is one of the main waste treatment methods used in Finland for treating separated organic waste. The composting process allows converting organic waste to a humus-like end product which can be used to increase the organic matter in agricultural soils, in gardening, or in landscaping. Microbes play a key role as degraders during the composting-process, and the microbiology of composting has been studied for decades, but there are still open questions regarding the microbiota in industrial composting processes. It is known that with the traditional, culturing-based methods only a small fraction, below 1%, of the species in a sample is normally detected. In recent years an immense diversity of bacteria, fungi and archaea has been found to occupy many different environments. Therefore the methods of characterising microbes constantly need to be developed further. In this thesis the presence of fungi and bacteria in full-scale and pilot-scale composting processes was characterised with cloning and sequencing. Several clone libraries were constructed and altogether nearly 6000 clones were sequenced. The microbial communities detected in this study were found to differ from the compost microbes observed in previous research with cultivation based methods or with molecular methods from processes of smaller scale, although there were similarities as well. The bacterial diversity was high. Based on the non-parametric coverage estimations, the number of bacterial operational taxonomic units (OTU) in certain stages of composting was over 500. Sequences similar to Lactobacillus and Acetobacteria were frequently detected in the early stages of drum composting. In tunnel stages of composting the bacterial community comprised of Bacillus, Thermoactinomyces, Actinobacteria and Lactobacillus. The fungal diversity was found to be high and phylotypes similar to yeasts were abundantly found in the full-scale drum and tunnel processes. In addition to phylotypes similar to Candida, Pichia and Geotrichum moulds from genus Thermomyces and Penicillium were observed in tunnel stages of composting. Zygomycetes were detected in the pilot-scale composting processes and in the compost piles. In some of the samples there were a few abundant phylotypes present in the clone libraries that masked the rare ones. The rare phylotypes were of interest and a method for collecting them from clone libraries for sequencing was developed. With negative selection of the abundant phylotyps the rare ones were picked from the clone libraries. Thus 41% of the clones in the studied clone libraries were sequenced. Since microbes play a central role in composting and in many other biotechnological processes, rapid methods for characterization of microbial diversity would be of value, both scientifically and commercially. Current methods, however, lack sensitivity and specificity and are therefore under development. Microarrays have been used in microbial ecology for a decade to study the presence or absence of certain microbes of interest in a multiplex manner. The sequence database collected in this thesis was used as basis for probe design and microarray development. The enzyme assisted detection method, ligation-detection-reaction (LDR) based microarray, was adapted for species-level detection of microbes characteristic of each stage of the composting process. With the use of a specially designed control probe it was established that a species specific probe can detect target DNA representing as little as 0.04% of total DNA in a sample. The developed microarray can be used to monitor composting processes or the hygienisation of the compost end product. A large compost microbe sequence dataset was collected and analysed in this thesis. The results provide valuable information on microbial community composition during industrial scale composting processes. The microarray method was developed based on the sequence database collected in this study. The method can be utilised in following the fate of interesting microbes during composting process in an extremely sensitive and specific manner. The platform for the microarray is universal and the method can easily be adapted for studying microbes from environments other than compost.

Construing and Defining the Out of Control : Addiction in the Media 1968-2008.

The four scientific articles comprising this doctoral dissertation offer new information on the presentation and construction of addiction in the mass media during the period 1968 - 2008. Diachronic surveys as well as quantitative and qualitative content analyses were undertaken to discern trends during the period in question and to investigate underlying conceptions of the problems in contemporary media presentations. The research material for the first three articles consists of a sample of 200 texts from Finland s biggest daily newspaper, Helsingin Sanomat, from the period 1968 - 2006. The fourth study examines English-language tabloid material published on the Internet in 2005 - 2008. A number of principal trends are identified. In addition to a significant increase in addiction reporting over time, the study shows that an internalisation of addiction problems took place in the media presentations under study. The phenomenon is portrayed and tackled from within the problems themselves, often from the viewpoint of the individuals concerned. The tone becomes more personal, and technical and detailed accounts are more and more frequent. Secondly, the concept of addiction is broadened. This can be dated to the 1990s. The concept undergoes a conventionalisation: it is used more frequently in a manner that is not thought to require explanation. The word riippuvuus (the closest equivalent to addiction in Finnish) was adopted more commonly in the reporting at the same time, in the 1990s. Thirdly, the results highlight individual self-governance as a superordinate principle in contemporary descriptions of addiction. If the principal demarcation in earlier texts was between us and them , it is now focused primarily on the individual s competence and ability to govern the self, to restrain and master one's behaviour. Finally, in the fourth study investigating textual constructions of female celebrities (Amy Winehouse, Britney Spears and Kate Moss) in Internet tabloids, various relations and functions of addiction problems, intoxication, body and gender were observed to function as cultural symbols. Addiction becomes a sign, or a style, that represents different significations in relation to the main characters in the tabloid stories. Tabloids, as a genre, play an important role by introducing other images of the problems than those featured in mainstream media. The study is positioned within the framework of modernity theory and its views on the need for self-reflexivity and biographies as tools for the creation and definition of the self. Traditional institutions such as the church, occupation, family etc. no longer play an important role in self-definition. This circumstance creates a need for a culture conveying stories of success and failure in relation to which the individual can position their own behaviour and life content. I propose that addiction , as a theme in media reporting, resolves the conflict that emanates from the ambivalence between the accessibility and the individualisation of consumer society, on the one hand, and the problematic behavioural patterns (addictions) that they may induce, on the other.

Towards Explaining the Use of Control Mechanisms in Foreign Subsidiaries of MNCs (summary section only)

Control is central to management and there is already a considerable body of research on control. However, the emergence and growth of multinational corporations (MNCs) has renewed the interest in control, as MNCs are complex (often large) organizations that face circumstances beyond those of national business organizations. The geographical dispersion of MNC activities means that the headquarters controls subsidiaries that differ with regard to power and that are embedded in different cultural, political, legal and educational systems. Foreign subsidiary control also takes place across language boundaries and physical (i.e. geographical) distances. In face of these challenges, how are foreign subsidiaries controlled? The thesis explores different types of control mechanisms and attempts to explain the degree to which they are used to control foreign subsidiaries. It contributes to existing knowledge on control by exploring how five different control mechanisms are related to each other. Previous research has tended to focus only on one or two control mechanisms and seldom has their effect on each other been explored. The thesis also contributes by including two central aspects of the MNC that have been neglected in much of the research on foreign subsidiary control: language competence of subsidiary staff and physical distance between the headquarters and its subsidiaries. The findings indicate that specific control mechanisms should not be studied in isolation as there are intricate relationships among the different control mechanisms. Language competence of the subsidiary staff can furthermore affect the type and degree of control that the headquarters can exercise over a subsidiary. The findings also indicate that changes in the physical distance between subsidiaries and its headquarters (i.e. a relocation of the headquarters as part of a restructuring process) can have great consequences for the headquarters-subsidiary relationship.