26 resultados para Quality of emergency
em Helda - Digital Repository of University of Helsinki
Resumo:
Aims: The aims of this study were 1) to identify and describe health economic studies that have used quality-adjusted life years (QALYs) based on actual measurements of patients' health-related quality of life (HRQoL); 2) to test the feasibility of routine collection of health-related quality of life (HRQoL) data as an indicator of effectiveness of secondary health care; and 3) to establish and compare the cost-utility of three large-volume surgical procedures in a real-world setting in the Helsinki University Central Hospital, a large referral hospital providing secondary and tertiary health-care services for a population of approximately 1.4 million. Patients and methods: So as to identify studies that have used QALYs as an outcome measure, a systematic search of the literature was performed using the Medline, Embase, CINAHL, SCI and Cochrane Library electronic databases. Initial screening of the identified articles involved two reviewers independently reading the abstracts; the full-text articles were also evaluated independently by two reviewers, with a third reviewer used in cases where the two reviewers could not agree a consensus on which articles should be included. The feasibility of routinely evaluating the cost-effectiveness of secondary health care was tested by setting up a system for collecting HRQoL data on approximately 4 900 patients' HRQoL before and after operative treatments performed in the hospital. The HRQoL data used as an indicator of treatment effectiveness was combined with diagnostic and financial indicators routinely collected in the hospital. To compare the cost-effectiveness of three surgical interventions, 712 patients admitted for routine operative treatment completed the 15D HRQoL questionnaire before and also 3-12 months after the operation. QALYs were calculated using the obtained utility data and expected remaining life years of the patients. Direct hospital costs were obtained from the clinical patient administration database of the hospital and a cost-utility analysis was performed from the perspective of the provider of secondary health care services. Main results: The systematic review (Study I) showed that although QALYs gained are considered an important measure of the effectiveness of health care, the number of studies in which QALYs are based on actual measurements of patients' HRQoL is still fairly limited. Of the reviewed full-text articles, only 70 reported QALYs based on actual before after measurements using a valid HRQoL instrument. Collection of simple cost-effectiveness data in secondary health care is feasible and could easily be expanded and performed on a routine basis (Study II). It allows meaningful comparisons between various treatments and provides a means for allocating limited health care resources. The cost per QALY gained was 2 770 for cervical operations and 1 740 for lumbar operations. In cases where surgery was delayed the cost per QALY was doubled (Study III). The cost per QALY ranges between subgroups in cataract surgery (Study IV). The cost per QALY gained was 5 130 for patients having both eyes operated on and 8 210 for patients with only one eye operated on during the 6-month follow-up. In patients whose first eye had been operated on previous to the study period, the mean HRQoL deteriorated after surgery, thus precluding the establishment of the cost per QALY. In arthroplasty patients (Study V) the mean cost per QALY gained in a one-year period was 6 710 for primary hip replacement, 52 270 for revision hip replacement, and 14 000 for primary knee replacement. Conclusions: Although the importance of cost-utility analyses has during recent years been stressed, there are only a limited number of studies in which the evaluation is based on patients own assessment of the treatment effectiveness. Most of the cost-effectiveness and cost-utility analyses are based on modeling that employs expert opinion regarding the outcome of treatment, not on patient-derived assessments. Routine collection of effectiveness information from patients entering treatment in secondary health care turned out to be easy enough and did not, for instance, require additional personnel on the wards in which the study was executed. The mean patient response rate was more than 70 %, suggesting that patients were happy to participate and appreciated the fact that the hospital showed an interest in their well-being even after the actual treatment episode had ended. Spinal surgery leads to a statistically significant and clinically important improvement in HRQoL. The cost per QALY gained was reasonable, at less than half of that observed for instance for hip replacement surgery. However, prolonged waiting for an operation approximately doubled the cost per QALY gained from the surgical intervention. The mean utility gain following routine cataract surgery in a real world setting was relatively small and confined mostly to patients who had had both eyes operated on. The cost of cataract surgery per QALY gained was higher than previously reported and was associated with considerable degree of uncertainty. Hip and knee replacement both improve HRQoL. The cost per QALY gained from knee replacement is two-fold compared to hip replacement. Cost-utility results from the three studied specialties showed that there is great variation in the cost-utility of surgical interventions performed in a real-world setting even when only common, widely accepted interventions are considered. However, the cost per QALY of all the studied interventions, except for revision hip arthroplasty, was well below 50 000, this figure being sometimes cited in the literature as a threshold level for the cost-effectiveness of an intervention. Based on the present study it may be concluded that routine evaluation of the cost-utility of secondary health care is feasible and produces information essential for a rational and balanced allocation of scarce health care resources.
Resumo:
Flax and hemp have traditionally been used mainly for textiles, but recently interest has also been focused on non-textile applications. Microbial quality throughout the whole processing chain of bast fibres has not previously been studied. This study concentrates on the microbial quality and possible microbial risks in the production chain of hemp and flax fibres and fibrous thermal insulations. In order to be able to utilize hemp and flax fibres, the bast fibres must be separated from the rest of the plant. Non-cellulosic components can be removed with various pretreatment processes, which are associated with a certain risk of microbial contamination. In this study enzymatic retting and steam explosion (STEX) were examined as pretreatment processes. On the basis of the results obtained in this study, the microbial contents on stalks of both plants studied increased at the end of the growing season and during the winter. However, by processing and mechanical separation it is possible to produce fibres containing less moulds and bacteria than the whole stem. Enzymatic treatment encouraged the growth of moulds in fibres. Steam explosion reduced the amount of moulds in fibres. Dry thermal treatment used in this study did not markedly reduce the amount of microbes. In this project an emission measurement chamber was developed which was suitable for measurements of emissions from both mat type and loose fill type insulations, and capable of interdisciplinary sampling. In this study, the highest amounts of fungal emissions were in the range of 10^3 10^5 cfu/m^3 from the flax and hemp insulations at 90% RH of air. The fungal emissions from stone wool, glass wool and recycled paper insulations were below 10^2 cfu/m^3 even at 90% RH. Equally low values were obtained from bast fibrous materials in lower humidities (at 30% and 80% RH of air). After drying of moulded insulations at 30% RH, the amounts of emitted moulds were in all cases higher compared to the emissions at 90% RH before drying. The most common fungi in bast fibres were Penicillium and Rhizopus. The widest variety of different fungi was in the untreated hemp and linseed fibres and in the commercial loose-fill flax insulation. Penicillium, Rhizopus and Paecilomyces were the most tolerant to steam explosion. According to the literature, the most common fungi in building materials and indoor air are Penicillium, Aspergillus and Cladosporium, which were all found in some of the bast fibre materials in this study. As organic materials, hemp and flax fibres contain high levels of nutrients for microbial growth. The amount of microbes can be controlled and somewhat decreased by the processing methods presented.
Resumo:
This thesis reports on investigations into the influence of heat treatment on the manufacturing of oat flakes. Sources of variation in the oat flake quality are reviewed, including the whole chain from the farm to the consumer. The most important quality parameters of oat flakes are the absence of lipid hydrolysing enzymes, specific weight, thickness, breakage (fines), water absorption. Flavour, colour and pasting properties are also important, but were not included in the experimental part of this study. Of particular interest was the role of heat processing. The first possible heat treatment may occur already during grain drying, which in Finland generally happens at the farm. At the mill, oats are often kilned to stabilise the product by inactivating lipid hydrolysing enzymes. Almost invariably steaming is used during flaking, to soften the groats and reduce flake breakage. This thesis presents the use of a material science approach to investigating a complex system, typical of food processes. A combination of fundamental and empirical rheological measurements was used together with a laboratory scale process to simulate industrial processing. The results were verified by means of industrial trials. Industrially produced flakes at three thickness levels (nominally 0.75, 0.85 and 0.90 mm) were produced from kilned and unkilned oat groats, and the flake strength was measured at different moisture contents. Kilning was not found to significantly affect the force required to puncture a flake with a 2mm cylindrical probe, which was taken as a measure of flake strength. To further investigate how heat processing contributes to flake quality, dynamic mechanical analysis was used to characterise the effect of heat on the mechanical properties of oats. A marked stiffening of the groat, of up to about 50% increase in storage modulus, was observed during first heating at around 36 to 57°C. This was also observed in tablets prepared from ground groats and extracted oat starch. This stiffening was thus attributed to increased adhesion between starch granules. Groats were steamed in a laboratory steamer and were tempered in an oven at 80 110°C for 30 90 min. The maximum force required to compress the steamed groats to 50% strain increased from 50.7 N to 57.5 N as the tempering temperature was increased from 80 to 110°C. Tempering conditions also affected water absorption. A significantly higher moisture content was observed for kilned (18.9%) compared to unkilned (17.1%) groats, but otherwise had no effect on groat height, maximum force or final force after a 5 s relaxation time. Flakes were produced from the tempered groats using a laboratory flaking machine, using a roll gap of 0.4 mm. Apart from specific weight, flake properties were not influenced by kilning. Tempering conditions however had significant effects on the specific weight, thickness and water absorption of the flakes, as well as on the amount of fine material (<2 mm) produced during flaking. Flake strength correlated significantly with groat strength and flake thickness. Trial flaking at a commercial mill confirmed that groat temperature after tempering influenced water absorption. Variation in flake strength was observed , but at the groat temperatures required to inactivate lipase, it was rather small. Cold flaking of groats resulted in soft, floury flakes. The results presented in this thesis suggest that heating increased the adhesion between starch granules. This resulted in an increase in the stiffness and brittleness of the groat. Brittle fracture, rather than plastic flow, during flaking could result in flaws and cracks in the flake. These would be expected to increase water absorption. This was indeed observed as tempering temperature increased. Industrial trials, conducted with different groat temperatures, confirmed the main findings of the laboratory experiments. The approach used in the present study allowed the systematic study of the effect of interacting process parameters on product quality. There have been few scientific studies of oat processing, and these results can be used to understand the complex effects of process variables on flake quality. They also offer an insight into what happens as the oat groat is deformed into a flake.
Resumo:
ALICE (A Large Ion Collider Experiment) is an experiment at CERN (European Organization for Nuclear Research), where a heavy-ion detector is dedicated to exploit the unique physics potential of nucleus-nucleus interactions at LHC (Large Hadron Collider) energies. In a part of that project, 716 so-called type V4 modules were assembles in Detector Laboratory of Helsinki Institute of Physics during the years 2004 - 2006. Altogether over a million detector strips has made this project the most massive particle detector project in the science history of Finland. One ALICE SSD module consists of a double-sided silicon sensor, two hybrids containing 12 HAL25 front end readout chips and some passive components, such has resistors and capacitors. The components are connected together by TAB (Tape Automated Bonding) microcables. The components of the modules were tested in every assembly phase with comparable electrical tests to ensure the reliable functioning of the detectors and to plot the possible problems. The components were accepted or rejected by the limits confirmed by ALICE collaboration. This study is concentrating on the test results of framed chips, hybrids and modules. The total yield of the framed chips is 90.8%, hybrids 96.1% and modules 86.2%. The individual test results have been investigated in the light of the known error sources that appeared during the project. After solving the problems appearing during the learning-curve of the project, the material problems, such as defected chip cables and sensors, seemed to induce the most of the assembly rejections. The problems were typically seen in tests as too many individual channel failures. Instead, the bonding failures rarely caused the rejections of any component. One sensor type among three different sensor manufacturers has proven to have lower quality than the others. The sensors of this manufacturer are very noisy and their depletion voltage are usually outside of the specification given to the manufacturers. Reaching 95% assembling yield during the module production demonstrates that the assembly process has been highly successful.
Resumo:
Thirty percent of 70-year-old women have osteoporosis; after age of 80 its prevalence is up to 70%. Postmenopausal women with osteoporosis seem to be at an increased risk for cardiovascular events, and deterioration of oral health, as shown by attachment loss of teeth, which is proportional to the severity of osteoporosis. Osteoporosis can be treated with many different medication, e.g. estrogen and alendronate. We randomized 90 elderly osteoporotic women (65-80 years of age) to receive hormone therapy (HT)(2mg E2+NETA), 10mg alendronate, and their combination for two years and compared their effects on bone mineral density (BMD) and turnover, two surrogate markers of the risk of cardiovascular diseases, C-reactive protein (CRP) and E-selectin, as well as oral health. The effect of HT on health-related quality of life (HRQoL) was studied in the population-based cohort of 1663 postmenopausal women (mean age 68 yr) (585 estrogen users and 1078 non-users). BMD was measured with dual-energy X-ray absorptiometry (DXA) at 0, 12 and 24 months. Urinary N-telopeptide (NTX) of type I collagen, a marker of bone resorption, and serum aminoterminal propeptide of human type I procollagen (PINP), a marker of bone formation, were measured every six months of treatment. Serum CRP and E-selectin, were measured at 0, 6, and 12 months. Dental, and periodontal conditions, and gingival crevicular fluid (GCF) matrix metalloproteinase (MMP)-8 levels were studied to evaluate the oral health status and for the mouth symptoms a structured questionnaire was used. The HRQoL was measured with 15D questionnaire. Lumbar spine BMD increased similarly in all treatment groups (6.8-8.4% and 9.1-11.2%). Only HT increased femoral neck BMD at both 12 (4.9%) and 24 months (5.8%), at the latter time point the HT group differed significantly from the other groups. HT reduced bone marker levels of NTX and PINP significantly less than other two groups.Oral HT significantly increased serum CRP level by 76.5% at 6 and by 47.1% (NS) at 12 months, and decreased serum E-selectin level by 24.3% and 30.0%. Alendronate had no effect on these surrogate markers. Alendronate caused a decrease in the resting salivary flow rate and tended to increase GCF MMP-8 levels. Otherwise, there was no effect on the parameters of oral health. HT improved the HRQoL of elderly women significantly on the dimensions of usual activities, vitality and sexual activity, but the overall improvement in HRQoL was neither statistically significant nor clinically important. In conclusion, bisphosphonates might be the first option to start the treatment of postmenopausal osteoporosis in the old age.
Resumo:
Prevention of cardiovascular diseases is known to postpone death, but in an aging society it is important to ensure that those who live longer are neither disabled nor suffering an inferior quality of life. It is essential both from the point of view of the aging individual as well as that of society that any individual should enjoy a good physical, mental and social quality of life during these additional years. The studies presented in this thesis investigated the impact of modifiable risk factors, all of which affect cardiovascular health in the long term, on mortality and health-related quality of life (HRQoL). The data is based on the all male cohort of the Helsinki Businessmen Study. This cohort, originally of 3.490 men born between 1919 and 1934 has been followed since the 1960s. The socioeconomic status of the participants is similar, since all the men were working in leading positions. Extensive baseline examinations were conducted among 2.375 of the men in 1974 when their mean age was 48 and at this time the health, medication and cardiovascular risk factors of the participants were observed. In 2000, at the mean age of 73, the HRQoL of the survivors of the original cohort was examined using the RAND-36 mailed questionnaire (n=1.864). RAND-36, along with the equivalent SF-36, is the world s most widely used means of assessing generic health. The response rate was generally over 90%. Mortality was retrieved from national registers in 2000 and 2002. For the six substudies of this thesis, the impact of four different modifiable cardiovascular risk factors (weight gain, cholesterol, alcohol and smoking) on the HRQoL in old age was studied both independently and in combination. The follow-up time for these studies varies from 26 up to 39 years. Mortality is reported separately or included in the RAND-36 scores for HRQoL. Elevated levels of all the risk factors examined among the participants in midlife led to a diminished life expectancy. Among survivors, lower weight gain in midlife was associated with better HRQoL, both physically and mentally. Higher levels of serum cholesterol in middle age indicated both an earlier mortality and a decline in the physical component of HRQoL in a dose-response manner during the 39-year follow-up. Mortality was significantly higher in the highest baseline category of reported mean alcohol consumption (≥ 5 drinks/day), but fairly comparable in abstainers and moderate drinkers during the 29-year follow-up. When HRQoL in old age was accounted for mortality, the men with the highest alcohol consumption in midlife clearly had poorer physical and mental health in old age, but the HRQoL of abstainers and those who drank alcohol in moderation were comparatively similar. The amount of cigarette smoking in midlife was shown to have had a dose-response effect on both mortality and HRQoL in old age during the 26 year follow-up. The men smoking over 20 cigarettes daily in middle age lost about 10 years of their life-expectancy. Meanwhile, the physical functioning of surviving heavy smokers in old age was similar to men 10 years older in the general population. The impact of clustered cardiovascular risk factors was examined by comparing two subcohorts of men who were healthy in 1974, but with different baseline risk factor status. The men with low risk had a 50 % lower mortality during the 29-years follow-up. Their RAND-36 scores for the physical quality of life in old age were significantly better, and the 2002 questionnaire examining psychological well-being indicated also significantly better mental health among the low-risk group. The results indicate that different risk factor levels in midlife have a meaningful impact on life-expectancy and the quality of these extra years. Leading a healthy lifestyle improves both survival and the quality of life.
Resumo:
Rheumatoid arthritis (RA) and other chronic inflammatory joint diseases already begin to affect patients health-related quality of life (HRQoL) in the earliest phases of these diseases. In treatment of inflammatory joint diseases, the last two decades have seen new strategies and treatment options introduced. Treatment is started at an earlier phase; combinations of disease-modifying anti-rheumatic drugs (DMARDs) and corticosteroids are used; and in refractory cases new drugs such as tumour necrosis factor (TNF) inhibitors or other biologicals can be started. In patients with new referrals to the Department of Rheumatology of the Helsinki University Central Hospital, we evaluated the 15D and the Stanford Health Assessment Questionnaire (HAQ) results at baseline and approximately 8 months after their first visit. Altogether the analysis included 295 patients with various rheumatic diseases. The mean baseline 15D score (0.822, SD 0.114) was significantly lower than for the age-matched general population (0.903, SD 0.098). Patients with osteoarthritis (OA) and spondyloarthropathies (SPA) reported the poorest HRQoL. In patients with RA and reactive arthritis (ReA) the HRQoL improved in a statistically significant manner during the 8-month follow-up. In addition, a clinically important change appeared in patients with systemic rheumatic diseases. HAQ score improved significantly in patients with RA, arthralgia and fibromyalgia, and ReA. In a study of 97 RA patients treated either with etanercept or adalimumab, we assessed their HRQoL with the RAND 36-Item Health Survey 1.0 (RAND-36) questionnaire. We also analysed changes in clinical parameters and the HAQ. With etanercept and adalimumab, the values of all domains in the RAND-36 questionnaire increased during the first 3 months. The efficacy of each in improving HRQoL was statistically significant, and the drug effects were comparable. Compared to Finnish age- and sex-matched general population values, the HRQoL of the RA patients was significantly lower at baseline and, despite the improvement, remained lower also at follow-up. Our RA patients had long-standing and severe disease that can explain the low HRQoL also at follow-up. In a pharmacoeconomic study of patients treated with infliximab we evaluated medical and work disability costs for patients with chronic inflammatory joint disease during one year before and one year after institution of infliximab treatment. Clinical and economic data for 96 patients with different arthritis diagnoses showed, in all patients, significantly improved clinical and laboratory variables. However, the medical costs increased significantly during the second period by 12 015 (95% confidence interval, 6 496 to 18 076). Only a minimal decrease in work disability costs occurred mean decrease 130 (-1 268 to 1 072). In a study involving a switch from infliximab to etanercept, we investigated the clinical outcome in 49 patients with RA. Reasons for switching were in 42% failure to respond by American College of Rheumatology (ACR) 50% criteria; in 12% adverse event; and in 46% non-medical reasons although the patients had responded to infliximab. The Disease Activity Score with 28 joints examined (DAS28) allowed us to measure patients disease activity and compare outcome between groups based on the reason for switching. In the patients in whom infliximab was switched to etanercept for nonmedical reasons, etanercept continued to suppress disease activity effectively, and 1-year drug survival for etanercept was 77% (95% CI, 62 to 97). In patients in the infliximab failure and adverse event groups, DAS28 values improved significantly during etanercept therapy. However, the 1-year drug survival of etanercept was only 43% (95% CI, 26 to 70) and 50% (95% CI, 33 to 100), respectively. Although the HRQoL of patients with inflammatory joint diseases is significantly lower than that of the general population, use of early and aggressive treatment strategies including TNF-inhibitors can improve patients HRQoL effectively. Further research is needed in finding new treatment strategies for those patients who fail to respond or lose their response to TNF-inhibitors.
Resumo:
This clinical study focused on effects of childhood specific language impairment (SLI) on daily functioning in late life. SLI is a neurobiological disorder with genetic predisposition and manifests as poor language production or comprehension or both in a child with age-level non-verbal intelligence and no other known cause for deficient language development. The prevalence rate of around 7% puts it among the most prevalent developmental disorders in childhood. Negative long-term effects, such as problems in learning and behavior, are frequent. In follow-up studies the focus has seldom been on self-perception of daily functioning and participation, which are considered important in the International Classification of Functioning, Disability, and Health (ICF). To investigate the self-perceived aspects of everyday functioning in individuals with childhood receptive SLI compared with age- and gender-matched control populations, the 15D, 16D, and 17D health-related quality of life (HRQoL) questionnaires were applied. These generic questionnaires include 15, 16, and 17 dimensions, respectively, and give both a single index score and a profile with values on each dimension. Information on different life domains (rehabilitation, education, employment etc.) from each age-group was collected with separate questionnaires. The study groups comprised adults, adolescents (12-16 years), and pre-adolescents (8-11 years) who had received a diagnosis of receptive SLI and had been examined, usually before school age, at the Department of Phoniatrics of Helsinki University Central Hospital, where children with language deficits caused by various etiologies are examined and treated by a multidisciplinary team. The adult respondents included 33 subjects with a mean age of 34 years. Measured with 15D, the subjects perceived their HRQoL to be nearly as good as that of their controls, but on the dimensions of speech, usual activities, mental functioning, and distress they were significantly worse off. They significantly more often lived with their parents (19%) or were pensioned (26%) than the adult Finnish population on average. Adults with self-perceived problems in finding words and in remembering instructions, manifestations of persistent language impairment, showed inferior every day functioning to the rest of the study group. Of the adolescents and pre-adolescents, 48 and 51, respectively, responded. The majority in both groups had received special education or extra educational support at school. They all had attended speech therapy at some point; at the time of the study only one adolescent, but every third pre-adolescent still received speech therapy. The 16D score of the adolescent or the 17D score of the pre-adolescents did not differ from that of their controls. The 16D profiles differed on some dimensions; subjects were significantly worse off on the dimension of mental functioning, but better off on the dimension of vitality than controls. Of the 17D dimensions, the study group was significantly worse off on speech, whereas the control group reported significantly more problems in sleeping. Of the childhood performance measures investigated, low verbal intelligence quotient (VIQ), which is often considered to reflect receptive language impairment, was in adults subjects significantly associated with some of the self-perceived problems, such as problems in usual activities and mental functioning. The 15D, 16D, and 17D questionnaires served well in measuring self-perceived HRQoL. Such standardized measures with population values are especially important in confirming with the ICF guidelines. In the future these questionnaires could perhaps be used on a more individual level in follow-up of children in clinics, and even in special schools and classes, to detect those children at greatest risk of negative long-term effects and perhaps diminished well-being regarding daily functioning and participation.
Resumo:
Occupational rhinitis is mainly caused by work environment and not by stimuli encountered outside the workplace. It differs from rhinitis that is worsened by, but not mainly caused by, workplace exposures. Occupational rhinitis can develop in response to allergens, inhaled irritants, or corrosive gases. The thesis evaluated the use of challenge tests in occupational rhinitis diagnostics, studied the long-term health-related quality of life among allergic occupational rhinitis patients, and the allergens of wheat grain among occupational respiratory allergy patients. The diagnosed occupational rhinitis was mainly allergic rhinitis, which was caused by occupational agents, most commonly flours and animal allergens. The non-IgE-mediated rhinitis reactions were less frequent and caused more often asthma than rhinitis. Both nasal challenges and inhalation challenges were found to be safe tests. The inhalation challenge tests had considerably resource-intensive methodology. However, the evaluation of nasal symptoms and signs together with bronchial reactions saved time and expense compared with the organization of multiple individual challenges. The scoring criteria used matched well with the weighted amount of discharge ≥ 0.2 g and in most cases gave comparable results. The challenge tests are valuable tools when there is uncertainty whether the patient's exposure should be reduced or discontinued. It was found that continuing exposure decreases health-related quality of life among patients with allergic occupational rhinitis despite of rhinitis medications, still approximately ten years after the diagnosis. Health-related quality of life among occupational rhinitis patients without any longer occupational exposure was mainly similar than that of the healthy controls. This highlights the importance of the reduction and cessation of occupational exposure. To achieve this, 17% of occupational rhinitis patients had been re-educated. Alpha-amylase inhibitors, lipid transfer protein 2G, thaumatin -like protein, and peroxidase I were found to be relevant allergens in Finnish patients with occupational respiratory wheat allergy. Of these allergens, thaumatin-like protein and lipid transfer protein 2G were found as new allergens associated with baker's rhinitis and asthma. The knowledge of the new clinically relevant proteins can be used in the future in the development of better standardized diagnostic preparations.