Primary total hip arthroplasty for primary osteoarthritis in Finland : A national register based analysis

The first aim of the current study was to evaluate the survival of total hip arthroplasty (THA) in patients aged 55 years and older on a nation-wide level. The second aim was to evaluate, on a nation wide-basis, the geographical variation of the incidence of primary THA for primary OA and also to identify those variables that are possibly associated with this variation. The third aim was to evaluate the effects of hospital volume: on the length of stay, on the numbers of re-admissions and on the numbers of complications of THR on population-based level in Finland. The survival of implants was analysed based on data from the Finnish Arthroplasty Register. The incidence and hospital volume data were obtained from the Hospital Discharge Register. Cementless total hip replacements had a significantly reduced risk of revision for aseptic loosening compared with cemented hip replacements. When revision for any reason was the end point in the survival analyses, there were no significant differences found between the groups. Adjusted incidence ratios of THA varied from 1.9- to 3.0-fold during the study period. Neither the average income within a region nor the morbidity index was associated with the incidence of THA. For the four categories of volume of total hip replacements performed per hospital, the length of the surgical treatment period was shorter for the highest volume group than for the lowest volume group. The odds ratio for dislocations was significantly lower in the high volume group than in the low volume group. In patients who were 55 years of age or older, the survival of cementless total hip replacements was as good as that of the cemented replacements. However, multiple wear-related revisions of the cementless cups indicate that excessive polyethylene wear was a major clinical problem with modular cementless cups. The variation in the long-term rates of survival for different cemented stems was considerable. Cementless proximal porous-coated stems were found to be a good option for elderly patients. When hip surgery was performed on with a large repertoire, the indications to perform THAs due to primary OA were tight. Socio-economic status of the patient had no apparent effect on THA rate. Specialization of hip replacements in high volume hospitals should reduce costs by significantly shortening the length of stay, and may reduce the dislocation rate.

Total hip arthroplasty in young patients : with special references to patients under 55 years of age and to patients with developmental dysplasia of the hip

There is an ongoing controversy as to which methods in total hip arthroplasty (THA) could provide young patients with best long-term results. THA is an especially demanding operation in patients with severely dysplastic hips. The optimal surgical treatment for these patients also remains controversial. The aim of this study was to evaluate the long-term survival of THA in young patients (<55 years at the time of the primary operation) on a nation-wide level, and to analyze the long-term clinical and radio-graphical outcome of uncemented THA in patients with severely dysplastic joints. Survival of 4661 primary THAs performed for primary osteoarthritis (OA), 2557 primary THAs per-formed for rheumatoid arthritis (RA), and modern uncemented THA designs performed for primary OA in young patients, were analysed from the Finnish Arthroplasty Register. A total of 68 THAs were per-formed in 56 consecutive patients with high congenital hip dislocation between 1989-1994, and 68 THAs were performed in 59 consecutive patients with severely dysplastic hips and a previous Schanz osteotomy of the femur between 1988-1995 at the Orton Orthopaedic Hospital, Helsinki, Finland. These patients underwent a detailed physical and radiographical evaluation at a mean of 12.3 years and 13.0 years postoperatively, respectively. The risk of stem revision due to aseptic loosening in young patients with primary OA was higher for cemented stems than for proximally porous-coated or HA-coated uncemented stems implanted over the 1991-2001 period. There was no difference in the risk of revision between all-poly cemented-cups and press-fit porous-coated uncemented cups implanted during the same period, when the end point was defined as any revision (including exchange of liner). All uncemented stem designs studied in young patients with primary OA had >90% survival rates at 10 years. The Biomet Bi-Metric stem had a 95% (95% CI 93-97) survival rate even at 15 years. When the end point was defined as any revision, 10 year survival rates of all uncemented cup designs except the Harris-Galante II decreased to <80%. In young patients with RA, the risk of stem revision due to aseptic loosening was higher with cemented stems than with proximally porous-coated uncemented stems. In contrast, the risk of cup revision was higher for all uncemented cup concepts than for all-poly cemented cups with any type of cup revision as the end point. The Harris hip score increased significantly (p<0.001) both in patients with high con-genital hip dislocation and in patients with severely dysplastic hips and a previous Schanz osteotomy, treated with uncemented THA. There was a negative Trendelenburg sign in 92% and in 88% of hips, respectively. There were 12 (18%) and 15 (22%) perioperative complications. The rate of survival for the CDH femoral components, with revision due to aseptic loosening as the end point, was 98% (95% CI 97-100) at 10 years in patients with high hip dislocation and 92% (95% CI, 86-99) at 14 years in patients with a previous Schanz osteotomy. The rate of survival for press-fit, porous-coated acetabular components, with revision due to aseptic loosening as the end point, was 95% (95% CI 89-100) at 10 years in patients with high hip dislocation, and 98% (95% CI 89-100) in patients with a previous Schanz osteotomy. When revision of the cup for any reason was defined as the end point, 10 year sur-vival rates declined to 88% (95% CI 81-95) and to 69% (95% CI, 56-82), respectively. For young patients with primary OA, uncemented proximally circumferentially porous- and HA-coated stems are the implants of choice. However, survival rates of modern uncemented cups are no better than that of all-poly cemented cups. Uncemented proximally circumferentially porous-coated stems and cemented all-poly cups are currently the implants of choice for young patients with RA. Uncemented THA, with placement of the cup at the level of the true acetabulum, distal advancement of the greater trochanter and femoral shortening osteotomy provided patients with high congenital hip dislocation good long-term outcomes. Most of the patients with severely dysplastic hips and a previous Schanz osteotomy can be successfully treated with the same method. However, the subtrochanteric segmental shortening with angular correction gives better leg length correction for the patients with a previous low-seated unilateral Schanz osteotomy.

Total Hip and Knee Arthoplasty for Osteoarthritis : Factors Related to the Early Outcome of Surgery

Some perioperative clinical factors related to the primary cemented arthroplasty operation for osteoarthritis of the hip or knee joint are studied and discussed in this thesis. In a randomized, double-blind study, 39 patients were divided into two groups: one receiving tranexamic acid and the other not receiving it. Tranexamic acid was given in a dose of 10 mg/kg before the operation and twice thereafter, at 8-hour intervals. Total blood loss was smaller in the tranexamic acid group than in the control group. No thromboembolic complications were noticed. In a prospective, randomized study, 58 patients with hip arthroplasty and 39 patients with knee arthroplasty were divided into groups with postoperative closed-suction drainage and without drainage. There was no difference in healing of the wounds, postoperative blood transfusions, complications or range of motion. As a result of this study, the use of drains is no longer recommended. In a randomised study the effectiveness of a femoral nerve block (25 patients) was compared with other methods of pain control (24 patients) on the first postoperative day after total knee arthroplasty. The femoral block consisted of a single injection administered at patients´ bedside during the surgeon´s hospital rounds. Femoral block patients reported less pain and required half of the amount of oxycodone. Additional femoral block or continued epidural analgesia was required more frequently by the control group patients. Pain management with femoral blocks resulted in less work for nursing staff. In a retrospective study of 422 total hip and knee arthroplasty cases the C-reactive protein levels and clinical course were examined. After hip and knee arthroplasty the maximal C-reactive protein values are seen on the second and third postoperative days, after which the level decreases rapidly. There is no difference between patients with cemented or uncemented prostheses. Major postoperative complications may cause a further increase in C-reactive protein levels at one and two weeks. In-hospital and outpatient postoperative control radiographs of 200 hip and knee arthroplasties were reviewed retrospectively. If postoperative radiographs are of good quality, there seems to be no need for early repetitive radiographs. The quality and safety of follow-up is not compromised by limiting follow-up radiographs to those with clinical indications. Exposure of the patients and the staff to radiation is reduced. Reading of the radiographs by only the treating orthopaedic surgeon is enough. These factors may seem separate from each other, but linking them together may help the treating orthopaedic surgeon to adequate patient care strategy. Notable savings can be achieved.

Sticking and erosion at carbon-containing plasma-facing materials in fusion reactors

Controlled nuclear fusion is one of the most promising sources of energy for the future. Before this goal can be achieved, one must be able to control the enormous energy densities which are present in the core plasma in a fusion reactor. In order to be able to predict the evolution and thereby the lifetime of different plasma facing materials under reactor-relevant conditions, the interaction of atoms and molecules with plasma first wall surfaces have to be studied in detail. In this thesis, the fundamental sticking and erosion processes of carbon-based materials, the nature of hydrocarbon species released from plasma-facing surfaces, and the evolution of the components under cumulative bombardment by atoms and molecules have been investigated by means of molecular dynamics simulations using both analytic potentials and a semi-empirical tight-binding method. The sticking cross-section of CH3 radicals at unsaturated carbon sites at diamond (111) surfaces is observed to decrease with increasing angle of incidence, a dependence which can be described by a simple geometrical model. The simulations furthermore show the sticking cross-section of CH3 radicals to be strongly dependent on the local neighborhood of the unsaturated carbon site. The erosion of amorphous hydrogenated carbon surfaces by helium, neon, and argon ions in combination with hydrogen at energies ranging from 2 to 10 eV is studied using both non-cumulative and cumulative bombardment simulations. The results show no significant differences between sputtering yields obtained from bombardment simulations with different noble gas ions. The final simulation cells from the 5 and 10 eV ion bombardment simulations, however, show marked differences in surface morphology. In further simulations the behavior of amorphous hydrogenated carbon surfaces under bombardment with D^+, D^+2, and D^+3 ions in the energy range from 2 to 30 eV has been investigated. The total chemical sputtering yields indicate that molecular projectiles lead to larger sputtering yields than atomic projectiles. Finally, the effect of hydrogen ion bombardment of both crystalline and amorphous tungsten carbide surfaces is studied. Prolonged bombardment is found to lead to the formation of an amorphous tungsten carbide layer, regardless of the initial structure of the sample. In agreement with experiment, preferential sputtering of carbon is observed in both the cumulative and non-cumulative simulations

Atomic scale engineering of carbon nanotubes

Carbon nanotubes, seamless cylinders made from carbon atoms, have outstanding characteristics: inherent nano-size, record-high Young’s modulus, high thermal stability and chemical inertness. They also have extraordinary electronic properties: in addition to extremely high conductance, they can be both metals and semiconductors without any external doping, just due to minute changes in the arrangements of atoms. As traditional silicon-based devices are reaching the level of miniaturisation where leakage currents become a problem, these properties make nanotubes a promising material for applications in nanoelectronics. However, several obstacles must be overcome for the development of nanotube-based nanoelectronics. One of them is the ability to modify locally the electronic structure of carbon nanotubes and create reliable interconnects between nanotubes and metal contacts which likely can be used for integration of the nanotubes in macroscopic electronic devices. In this thesis, the possibility of using ion and electron irradiation as a tool to introduce defects in nanotubes in a controllable manner and to achieve these goals is explored. Defects are known to modify the electronic properties of carbon nanotubes. Some defects are always present in pristine nanotubes, and naturally are introduced during irradiation. Obviously, their density can be controlled by irradiation dose. Since different types of defects have very different effects on the conductivity, knowledge of their abundance as induced by ion irradiation is central for controlling the conductivity. In this thesis, the response of single walled carbon nanotubes to ion irradiation is studied. It is shown that, indeed, by energy selective irradiation the conductance can be controlled. Not only the conductivity, but the local electronic structure of single walled carbon nanotubes can be changed by the defects. The presented studies show a variety of changes in the electronic structures of semiconducting single walled nanotubes, varying from individual new states in the band gap to changes in the band gap width. The extensive simulation results for various types of defect make it possible to unequivocally identify defects in single walled carbon nanotubes by combining electronic structure calculations and scanning tunneling spectroscopy, offering a reference data for a wide scientific community of researchers studying nanotubes with surface probe microscopy methods. In electronics applications, carbon nanotubes have to be interconnected to the macroscopic world via metal contacts. Interactions between the nanotubes and metal particles are also essential for nanotube synthesis, as single walled nanotubes are always grown from metal catalyst particles. In this thesis, both growth and creation of nanotube-metal nanoparticle interconnects driven by electron irradiation is studied. Surface curvature and the size of metal nanoparticles is demonstrated to determine the local carbon solubility in these particles. As for nanotube-metal contacts, previous experiments have proved the possibility to create junctions between carbon nanotubes and metal nanoparticles under irradiation in a transmission electron microscope. In this thesis, the microscopic mechanism of junction formation is studied by atomistic simulations carried out at various levels of sophistication. It is shown that structural defects created by the electron beam and efficient reconstruction of the nanotube atomic network, inherently related to the nanometer size and quasi-one dimensional structure of nanotubes, are the driving force for junction formation. Thus, the results of this thesis not only address practical aspects of irradiation-mediated engineering of nanosystems, but also contribute to our understanding of the behaviour of point defects in low-dimensional nanoscale materials.

Diffraction and Total Cross-Section at the Tevatron and the LHC

At the Tevatron, the total p_bar-p cross-section has been measured by CDF at 546 GeV and 1.8 TeV, and by E710/E811 at 1.8 TeV. The two results at 1.8 TeV disagree by 2.6 standard deviations, introducing big uncertainties into extrapolations to higher energies. At the LHC, the TOTEM collaboration is preparing to resolve the ambiguity by measuring the total p-p cross-section with a precision of about 1 %. Like at the Tevatron experiments, the luminosity-independent method based on the Optical Theorem will be used. The Tevatron experiments have also performed a vast range of studies about soft and hard diffractive events, partly with antiproton tagging by Roman Pots, partly with rapidity gap tagging. At the LHC, the combined CMS/TOTEM experiments will carry out their diffractive programme with an unprecedented rapidity coverage and Roman Pot spectrometers on both sides of the interaction point. The physics menu comprises detailed studies of soft diffractive differential cross-sections, diffractive structure functions, rapidity gap survival and exclusive central production by Double Pomeron Exchange.

The significance of brittle reaction layers in fusing of dental ceramics to titanium

This thesis comprises four intercomplementary parts that introduce new approaches to brittle reaction layers and mechanical compatibility of metalloceramic joints created when fusing dental ceramics to titanium. Several different methods including atomic layer deposition (ALD), sessile drop contact angle measurements, scanning acoustic microscopy (SAM), three-point bending (TPB, DIN 13 927 / ISO 9693), cross-section microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS) were employed. The first part investigates the effects of TiO2 layer structure and thickness on the joint strength of the titanium-metalloceramic system. Samples with all tested TiO2 thicknesses displayed good ceramics adhesion to Ti, and uniform TPB results. The fracture mode was independent of oxide layer thickness and structure. Cracking occurred deeper inside titanium, in the oxygen-rich Ti[O]x solid solution surface layer. During dental ceramics firing TiO2 layers dissociate and joints become brittle with increased dissolution of oxygen into metallic Ti and consequent reduction in the metal plasticity. To accomplish an ideal metalloceramic joint this needs to be resolved. The second part introduces photoinduced superhydrophilicity of TiO2. Test samples with ALD deposited anatase TiO2 films were produced. Samples were irradiated with UV light to induce superhydrophilicity of the surfaces through a cascade leading to increased amount of surface hydroxyl groups. Superhydrophilicity (contact angle ~0˚) was achieved within 2 minutes of UV radiation. Partial recovery of the contact angle was observed during the first 10 minutes after UV exposure. Total recovery was not observed within 24h storage. Photoinduced ultrahydrophilicity can be used to enhance wettability of titanium surfaces, an important factor in dental ceramics veneering processes. The third part addresses interlayers designed to restrain oxygen dissolution into Ti during dental ceramics fusing. The main requirements for an ideal interlayer material are proposed. Based on these criteria and systematic exclusion of possible interlayer materials silver (Ag) interlayers were chosen. TPB results were significantly better in when 5 μm Ag interlayers were used compared to only Al2O3-blasted samples. In samples with these Ag interlayers multiple cracks occurred inside dental ceramics, none inside Ti structure. Ag interlayers of 5 μm on Al2O3-blasted samples can be efficiently used to retard formation of the brittle oxygen-rich Ti[O]x layer, thus enhancing metalloceramic joint integrity. The most brittle component in metalloceramic joints with 5 μm Ag interlayers was bulk dental ceramics instead of Ti[O]x. The fourth part investigates the importance of mechanical interlocking. According to the results, the significance of mechanical interlocking achieved by conventional surface treatments can be questioned as long as the formation of the brittle layers (mainly oxygen-rich Ti[O]x) cannot be sufficiently controlled. In summary in contrast to former impressions of thick titanium oxide layers this thesis clearly demonstrates diffusion of oxygen from sintering atmosphere and SiO2 to Ti structures during dental ceramics firing and the following formation of brittle Ti[O]x solid solution as the most important factors predisposing joints between Ti and SiO2-based dental ceramics to low strength. This among other predisposing factors such as residual stresses created by the coefficient of thermal expansion mismatch between dental ceramics and Ti frameworks can be avoided with Ag interlayers.

Perinatal mortality and maternal health in rural China

Background and context Since the economic reforms of 1978, China has been acclaimed as a remarkable economy, achieving 9% annual growth per head for more than 25 years. However, China's health sector has not fared well. The population health gains slowed down and health disparities increased. In the field of health and health care, significant progress in maternal care has been achieved. However, there still remain important disparities between the urban and rural areas and among the rural areas in terms of economic development. The excess female infant deaths and the rapidly increasing sex ratio at birth in the last decade aroused serious concerns among policy makers and scholars. Decentralization of the government administration and health sector reform impacts maternal care. Many studies using census data have been conducted to explore the determinants of a high sex ratio at birth, but no agreement has been so far reached on the possible contributing factors. No study using family planning system data has been conducted to explore perinatal mortality and sex ratio at birth and only few studies have examined the impact of the decentralization of government and health sector reforms on the provision and organization of maternal care in rural China. Objectives The general objective of this study was to investigate the state of perinatal health and maternal care and their determinants in rural China under the historic context of major socioeconomic reforms and the one child family planning policy. The specific objectives of the study included: 1) to study pregnancy outcomes and perinatal health and their correlates in a rural Chinese county; 2) to examine the issue of sex ratio at birth and its determinants in a rural Chinese county; 3) to explore the patterns of provision, utilization, and content of maternal care in a rural Chinese county; 4) to investigate the changes in the use of maternal care in China from 1991 to 2003. Materials and Methods This study is based on a project for evaluating the prenatal care programme in Dingyuan county in 1999-2003, Anhui province, China and a nationwide household health survey to describe the changes in maternal care utilization. The approaches used included a retrospective cohort study, cross sectional interview surveys, informant interviews, observations and the use of statistical data. The data sources included the following: 1) A cohort of pregnant women followed from pregnancy up to 7 days after birth in 20 townships in the study county, collecting information on pregnancy outcomes using family planning records; 2) A questionnaire interview survey given to women who gave birth between 2001 and 2003; 3) Various statistical and informant surveys data collected from the study county; 4) Three national household health interview survey data sets (1993-2003) were utilized, and reanalyzed to described the changes in maternity care utilization. Relative risks (RR) and their confidence intervals (CI) were calculated for comparison between parity, approval status, infant sex and township groups. The chi-square test was used to analyse the disparity of use of maternal care between and within urban and rural areas and its trend across the years in China. Logistic regression was used to analyse the factors associated with hospital delivery in rural areas. Results There were 3697 pregnancies in the study cohort, resulting in 3092 live births in a total population of 299463 in the 20 study townships during 1999-2000. The average age at pregnancy in the cohort was 25.9 years. Of the women, 61% were childless, 38% already had one child and 0.3% had two children before the current pregnancy. About 90% of approved pregnancies ended in a live birth while 73% of the unapproved ones were aborted. The perinatal mortality rate was 69 per thousand births. If the 30 induced abortions in which the gestational age was more than 28 weeks had been counted as perinatal deaths, the perinatal mortality rate would have been as high as 78 per thousand. The perinatal mortality rate was negatively associated with the wealth of the township. Approximately two thirds of the perinatal deaths occurred in the early neonatal period. Both the still birth rate and the early neonatal death rate increased with parity. The risk of a stillbirth in a second pregnancy was almost four times that for a first pregnancy, while the risk of early neonatal deaths doubled. The early neonatal mortality rate was twice as high for female as for male infants. The sex difference in the early neonatal mortality rate was mainly attributable to mortality in second births. The male early neonatal mortality rate was not affected by parity, while the female early neonatal mortality rate increased dramatically with parity: it was about six times higher for second births than for first births. About 82% early neonatal deaths happened within 24 hours after birth, and during that time, girls were almost three times more likely to die than boys. The death rate of females on the day of birth increased much more sharply with parity than that of males. The total sex ratio at birth of 3697 registered pregnancies was 152 males to 100 females, with 118 and 287 in first and second pregnancies, respectively. Among unapproved pregnancies, there were almost 5 live-born boys for each girl. Most prenatal and delivery care was to be taken care of in township hospitals. At the village level, there were small private clinics. There was no limitation period for the provision of prenatal and postnatal care by private practitioners. They were not permitted to provide delivery care by the county health bureau, but as some 12% of all births occurred either at home or at private clinics; some village health workers might have been involved. The county level hospitals served as the referral centers for the township hospitals in the county. However, there was no formal regulation or guideline on how the referral system should work. Whether or not a woman was referred to a higher level hospital depended on the individual midwife's professional judgment and on the clients' compliance. The county health bureau had little power over township hospitals, because township hospitals had in the decentralization process become directly accountable to the township government. In the township and county hospitals only 10-20% of the recurrent costs were funded by local government (the township hospital was funded by the township government and the county hospital was funded by the county government) and the hospitals collected user fees to balance their budgets. Also the staff salaries depended on fee incomes by the hospital. The hospitals could define the user charges themselves. Prenatal care consultations were however free in most township hospitals. None of the midwives made postnatal home visits, because of low profit of these services. The three national household health survey data showed that the proportion of women receiving their first prenatal visit within 12 weeks increased greatly from the early to middle 1990s in all areas except for large cities. The increase was much larger in the rural areas, reducing the urban-rural difference from more than 4 times to about 1.4 times. The proportion of women that received antenatal care visits meeting the Ministry of Health s standard (at least 5 times) in the rural areas increased sharply from 12% in 1991-1993 to 36% in 2001-2003. In rural areas, the proportion increase was much faster in less developed areas than in developed areas. The hospital delivery rate increased slightly from 90% to 94% in urban areas while the proportion increased from 27% to 69% in rural areas. The fastest change was found to be in type 4 rural areas, where the utilization even quadrupled. The overall difference between rural and urban areas was substantially narrowed over the period. Multiple logistic regression analysis shows that time periods, residency in rural or urban areas, income levels, age group, education levels, delivery history, occupation, health insurance and distance from the nearest health care facilities were significantly associated with hospital delivery rates. Conclusions 1. Perinatal mortality in this study was much higher than that for urban areas as well as any reported rate from specific studies in rural areas of China. Previous studies in which calculations of infant mortality were not based on epidemiological surveys have been shown to underestimate the rates by more than 50%. 2. Routine statistics collected by the Chinese family planning system proved to be a reliable data source for studying perinatal health, including still births, neonatal deaths, sex ratio at birth and among newborns. National Household Health Survey data proved to be a useful and reliable data source for studying population health and health services. Prior to this research there were few studies in these areas available to international audiences. 3.Though perinatal mortality rate was negatively associated with the level of township economic development, the excess female early neonatal mortality rate contributed much more to high perinatal mortality rate than economic factors. This was likely a result of the role of the family planning policy and the traditional preferences for sons, which leads to lethal neglect of female newborns and high perinatal mortality. 4. The selective abortions of female foetuses were likely to contribute most to the high sex ratio at birth. The underreporting of female births seemed to have played a secondary role. The higher early neonatal mortality rate in second-born as compared to first-born children, particularly in females, may indicate that neglect or poorer care of female newborn infants also contributes to the high sex ratio at birth or among newborns. Existing family planning policy proved not to effectively control the steadily increased birth sex ratio. 5. The rural-urban gap in service utilization was on average significantly narrowed in terms of maternal healthcare in China from 1991 to 2003. This demonstrates that significant achievements in reducing inequities can be made through a combination of socio-economic development and targeted investments in improving health services, including infrastructure, staff capacities, and subsidies to reduce the costs of service utilization for the poorest. However, the huge gap which persisted among cities of different size and within different types of rural areas indicated the need for further efforts to support the poorest areas. 6. Hospital delivery care in the study county was better accepted by women because most of women think delivery care was very important while prenatal and postnatal care were not. Hospital delivery care was more systematically provided and promoted than prenatal and postnatal care by township hospital in the study area. The reliance of hospital staff income on user fees gave the hospitals an incentive to put more emphasis on revenue generating activities such as delivery care instead of prenatal and postnatal care, since delivery care generated much profits than prenatal and postnatal care . Recommendations 1. It is essential for the central government to re-assess and modify existing family planning policies. In order to keep national sex balance, the existing practice of one couple one child in urban areas and at-least-one-son a couple in rural areas should be gradually changed to a two-children-a-couple policy throughout the country. The government should establish a favourable social security policy for couples, especially for rural couples who have only daughters, with particular emphasis on their pension and medical care insurance, combined with an educational campaign for equal rights for boys and girls in society. 2. There is currently no routine vital-statistics registration system in rural China. Using the findings of this study, the central government could set up a routine vital-statistics registration system using family planning routine work records, which could be used by policy makers and researchers. 3. It is possible for the central and provincial government to invest more in the less developed and poor rural areas to increase the access of pregnant women in these areas to maternal care services. Central government together with local government should gradually provide free maternal care including prenatal and postnatal as well as delivery care to the women in poor and less developed rural areas. 4. Future research could be done to explore if county and the township level health care sector and the family planning system could be merged to increase the effectiveness and efficiency of maternal and child care. 5. Future research could be done to explore the relative contribution of maternal care, economic development and family planning policy on perinatal and child health using prospective cohort studies and community based randomized trials. Key words: perinatal health, perinatal mortality, stillbirth, neonatal death, sex selective abortion, sex ratio at birth, family planning, son preference, maternal care, prenatal care, postnatal care, equity, China

Selective-Area Atomic Layer Deposition

Atomic layer deposition (ALD) is a method to deposit thin films from gaseous precursors to the substrate layer-by-layer so that the film thickness can be tailored with atomic layer accuracy. Film tailoring is even further emphasized with selective-area ALD which enables the film growth to be controlled also on the substrate surface. Selective-area ALD allows the decrease of a process steps in preparing thin film devices. This can be of a great technological importance when the ALD films become into wider use in different applications. Selective-area ALD can be achieved by passivation or activation of a surface. In this work ALD growth was prevented by octadecyltrimethoxysilane, octadecyltrichlorosilane and 1-dodecanethiol SAMs, and by PMMA (polymethyl methacrylate) and PVP (poly(vinyl pyrrolidone) polymer films. SAMs were prepared from vapor phase and by microcontact printing, and polymer films were spin coated. Microcontact printing created patterned SAMs at once. The SAMs prepared from vapor phase and the polymer mask layers were patterned by UV lithography or lift-off process so that after preparation of a continuous mask layer selected areas of them were removed. On these areas the ALD film was deposited selectively. SAMs and polymer films prevented the growth in several ALD processes such as iridium, ruthenium, platinum, TiO2 and polyimide so that the ALD films did grow only on areas without SAM or polymer mask layer. PMMA and PVP films also protected the surface against Al2O3 and ZrO2 growth. Activation of the surface for ALD of ruthenium was achieved by preparing a RuOX layer by microcontact printing. At low temperatures the RuCp2-O2 process nucleated only on this oxidative activation layer but not on bare silicon.