一种并联机床的位置、速度和加速度逆解

本文针对一种混合结构的并联机器人机床,采用串并联运动学等效的方法,进行了运动学研究,推导了系统的位移、速度和加速度逆解的表达式,这可用于机床在加工时的运动规划及插补算法的实现。本文还进行了运动学仿真研究,机床的实际加工操作应用的结果表明,推导的运动学算法的正确性。

串并联数控机床的作业空间分析

鉴于并联机床普遍存在有效作业空间小、运动控制复杂和实用刚度还不理想等不足．采用了串并联混合式机床运动结构．针对所研究的4—4构型串并联机床,分析了影响作业性能的几何约束条件,采用基于位置逆解模型的极限边界数值搜索法,确定了机床作业空间,并通过数值仿真研究获得了机床运动参数和结构参数对作业空间的影响规律，为优化机床结构尺寸以获得尽可能大的有效作业空间奠定了基础。

五轴并联铣床特征参数误差灵敏度分析

将并联机构等效为由串联机构构成的空间闭环机构，运用 D－ H方法系统研究了五轴并联铣床的特征参数误差对运动平台位姿误差的影响，揭示出特征参数沿机床各位姿方向误差灵敏度变化规律。仿真结果不仅证实了现有机床机构设计合理，而且为今后并联机床进一步精度设计提供了可靠依据。

并联机床平面约束机构误差分析与建模

针对五轴数控机床平面约束机构进行了误差分析 ,指出了并联机床平面约束机构误差主要影响因素为机构的制造误差和安装误差·前者与由其引起的约束机构顶边中点沿x方向的位移成非线性关系 ,而后者则成线性关系·提出了一种依据测量数据反演非线性误差模型的建模方法 ,给出了五轴并联机床约束机构实测信息与模型输出间的多项式误差模型·比较仿真结果与测量结果可知 ,基于上述方法建立的误差模型精确 ,进而利用该模型对机床进行实时精度补偿 ,可使机床x方向定位精度大为提高

并联机床的发展现状与展望

论述并联机床的发展现状及与传统机床的区别。在对国内外典型并联机床样机的工作原理分析的基础上，指出目前并联机床研究中所面临的主要问题，并对并联机床的研究发展方向进行了展望。

基于测量数据反演并联机床非线性位姿误差模型

利用最小二乘技术识别模型参数 ,将非线性问题作线性化处理 ,提出了一种基于测量数据反演非线性误差模型的建模方法。结合算例 ,指出了此类模型设计应注意的问题。五轴并联机床约束机构误差模型仿真结果表明 ,由此得到的误差模型精度高。利用所得模型对机床位姿进行补偿 ,即可提高机床沿该位姿方向的定位精度

基于四自由度并联机构的数控机床研究

介绍一种基于混合型四自由度并联平台机构开发的五坐标并联机床 .由于其独特的机构设计 ,与基于 Stewart平台的并联机床相比 ,X方向的进给运动与运动平台分离 ,改由工作台单独进给 ,因而其工作空间成倍增大 .采用龙门框架结构和滚珠丝杠支承方案使机床获得更高的刚度 .给出了该机床运动学逆解 ,控制系统采用基于 PC的数控系统进行五轴联动控制

一种并联机床运动平台位姿测量方法

提出一种采用附加测量机构直接测量并联机床运动平台位姿精度的方法。其基本思想是根据运动平台的运动特性在固定平台和运动平台之间增设附加测量机构，当运动平台运动时带动测量机构运动，通过安装在测量机构上的传感器测得广义坐标参量， 经运动学建模即可得到运动平台的位姿。当测量机构位姿正解求解速度满足实时控制要求时，利用该反馈信息对机床进行实时精度补偿和控制。基于上述思想建立的并联机床位姿测量系统可部分排除机床切削力变形和运动副间隙等误差， 从而提高机床的位姿测量精度。以一种五坐标并联机床为例，介绍采用附加测量机构直接测量运动平台位姿精度的建模方法。其中， 测量机构的综合十分重要。测量机构的组成决定了运动学模型的复杂程度， 即决定了运动学模型的计算效率。

A Structured Prediction Approach for Statistical Machine Translation

We propose a new formally syntax-based method for statistical machine translation. Transductions between parsing trees are transformed into a problem of sequence tagging, which is then tackled by a search- based structured prediction method. This allows us to automatically acquire transla- tion knowledge from a parallel corpus without the need of complex linguistic parsing. This method can achieve compa- rable results with phrase-based method (like Pharaoh), however, only about ten percent number of translation table is used. Experiments show that the structured pre- diction approach for SMT is promising for its strong ability at combining words.

A New Designed Two-Dimensional Bifurcation Parallel-Plate Flow Chamber

解决平行平板流槽每次实验只能观测壁面培养细胞受一种剪应力作用的问题。作者在平行平板流槽的基础上,首次提出了一种改进后的流槽--二维平板分叉流槽。通过数值模拟,给出了流体作定常流动时,流速和壁面剪应力的分布。结果发现,利用这种二维平板分叉流槽可以研究壁面培养的细胞在不同大小剪应力作用下的力学行为。该研究结果为流槽的合理设计和使用,并分析剪应力空间分布对内皮细胞的影响有重要实际意义。

A Label-Free Protein Microfluidic Array for Parallel Immunoassays

A label-free protein microfluidic array for immunoassays based on the combination of imaging ellipsometry and an integrated microfluidic system is presented. Proteins can be patterned homogeneously on substrate in array format by the microfluidic system simultaneously. After preparation, the protein array can be packed in the microfluidic system which is full of buffer so that proteins are not exposed to denaturing conditions. With simple microfluidic channel junction, the protein microfluidic array can be used in serial or parallel format to analyze single or multiple samples simultaneously. Imaging ellipsometry is used for the protein array reading with a label-free format. The biological and medical applications of the label-free protein microfluidic array are demonstrated by screening for antibody–antigen interactions, measuring the concentration of the protein solution and detecting five markers of hepatitis B.

Experimental Investigation On The Holdup Distribution Of Oil-Water Two-Phase Flow In Horizontal Parallel Tubes

An experimental investigation was conducted to study the holdup distribution of oil and water two-phase flow in two parallel tubes with unequal tube diameter. Tests were performed using white oil (of viscosity 52 mPa s and density 860 kg/m(3)) and tap water as liquid phases at room temperature and atmospheric outlet pressure. Measurements were taken of water flow rates from 0.5 to 12.5 m(3)/h and input oil volume fractions from 3 to 94 %. Results showed that there were different flow pattern maps between the run and bypass tubes when oil-water two-phase flow is found in the parallel tubes. At low input fluid flow rates, a large deviation could be found on the average oil holdup between the bypass and the run tubes. However, with increased input oil fraction at constant water flow rate, the holdup at the bypass tube became close to that at the run tube. Furthermore, experimental data showed that there was no significant variation in flow pattern and holdup between the run and main tubes. In order to calculate the holdup in the form of segregated flow, the drift flux model has been used here.

平行圆板流动腔(Parallel-circular-plateflowchamber)

<正>生物力学研究的趋势十分明显的是,由宏观方面的研究转向细观和微观方面的研究。人们从个体、器官和组织的生物力学方面,转向细胞甚至分子水平的研究。在力的作用下,细胞的形态、生理作用等发生的变化引起了人们极大的兴趣,其中流体流动时剪应力对细胞的作用尤为人们所特别关注,因为有血液在血管中流动时的剪应力对血管内皮细胞的作用这样的实际生理背景。剪应力不但可以影响内皮细胞的形态结构,而且对在细胞诸多生理方面有影响。

Parallel Fully-Implicit Computation of MHD Acceleration Experiments

A three-dimensional MHD solver is described in the paper. The solver simulates reacting flows with nonequilibrium between translational-rotational, vibrational and electron translational modes. The conservation equations are discretized with implicit time marching and the second-order modified Steger-Warming scheme, and the resulted linear system is solved iteratively with Newton-Krylov-Schwarz method that is implemented by PETSc package. The results of convergence tests are plotted, which show good scalability and convergence around twice faster when compared with the DPLR method. Then five test runs are conducted simulating the experiments done at the NASA Ames MHD channel, and the calculated pressures, temperatures, electrical conductivity, back EMF, load factors and flow accelerations are shown to agree with the experimental data. Our computation shows that the electrical conductivity distribution is not uniform in the powered section of the MHD channel, and that it is important to include Joule heating in order to calculate the correct conductivity and the MHD acceleration.

On optimal message vector length for block single parallel partition algorithm in a three-dimensional ADI solver

It has long been recognized that many direct parallel tridiagonal solvers are only efficient for solving a single tridiagonal equation of large sizes, and they become inefficient when naively used in a three-dimensional ADI solver. In order to improve the parallel efficiency of an ADI solver using a direct parallel solver, we implement the single parallel partition (SPP) algorithm in conjunction with message vectorization, which aggregates several communication messages into one to reduce the communication costs. The measured performances show that the longest allowable message vector length (MVL) is not necessarily the best choice. To understand this observation and optimize the performance, we propose an improved model that takes the cache effect into consideration. The optimal MVL for achieving the best performance is shown to depend on number of processors and grid sizes. Similar dependence of the optimal MVL is also found for the popular block pipelined method.