A general theory on media with randomly distributed inclusions .1. The average field behaviors

In this paper, a theory is developed to calculate the average strain field in the materials with randomly distributed inclusions. Many previous researches investigating the average field behaviors were based upon Mori and Tanaka's idea. Since they were restricted to studying those materials with uniform distributions of inclusions they did not need detailed statistical information of random microstructures, and could use the volume average to replace the ensemble average. To study more general materials with randomly distributed inclusions, the number density function is introduced in formulating the average field equation in this research. Both uniform and nonuniform distributions of inclusions are taken into account in detail.

Investigation on average void fraction for air/non-Newtonian power-law fluids two-phase flow in downward inclined pipes

The present work has been carried out to investigate on the average void fraction of gas/non-Newtonian fluids flow in downward inclined pipes. The influences of pipe inclination angle on the average void fraction were studied experimentally. A simple correlation, which incorporated the method of Vlachos et al. for gas/Newtonain fluid horizontal flow, the correction factor of Farooqi and Richardson and the pipe inclination angle, was proposed to predict the average void fraction of gas/non-Newtonian power-law stratified flow in downward inclined pipes. The correlation was based on 470 data points covering a wide range of flow rates for different systems at diverse angles. A good agreement was obtained between theory and data and the fitting results could describe the majority of the experimental data within ±20%.

Mode properties of off-axis one-sided hybrid resonator for novel high average power dual-slab laser

A novel dual-slab laser with off-axis one-sided hybrid resonator is presented. The mode properties of the hybrid resonator are calculated using a fast Fourier transform method (FFT). The influence of wavefront distoration on the output beam quality is considered. Results indicate that the novel dual-slab laser is better than the normal dual-slab laser with off-axis one-sided hybrid resonator.

20-W average power, high repetition rate, nanosecond pulse with diffraction limit from an all-fiber MOPA system

In this article, we report an all-fiber master oscillator power amplifier (MOPA) system, which can provide high repetition rate and nanosecond pulse with diffraction-limit. The system was constructed using a (2 + 1) X 1 multimode combiner. The Q-Switched, LD pumped Nd:YVO4 solid-state laser wets used (is master oscillator. The 976-nm fiber-coupled module is used as pump source. A 10-m long China-made Yb3+-doped D-shape double-clad large-mode-area fiber was used as amplifier fiber. The MOPA produced as much as 20-W average power with nanosecond pulse and near diffraction limited. The pulse duration is maintained at about 15 its during 50-175 kHz. The system employs a simple and compact architecture and is therefore suitable for the use in practical applications such as scientific and military airborne LIDAR and imaging. Based oil this system. the amplification performances of. the all fiber amplifier is investigated. (C) 2008 Wiley Periodicals, Inc.

Welding of Al alloy plates using a novel high-average-power pulsed CO2 laser

A novel high-average-power pulsed CO2 laser with a unique electrode structure is presented. The operation of a 5-kW transverse-flow CO2 laser with the preionized pulse-train switched technique results in pulsation of the laser power, and the average laser power is about 5 kW. The characteristic of this technique is switching the preionized pulses into pulse trains so as to use the small preionized power (hundreds of watts) to control the large main-discharge power (tens of kilowatts). By this means, the cost and the complexity of the power supply are greatly reduced. The welding of LF2, LF21, LD2, and LY12 aluminum alloy plates has been successfully achieved using this laser. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

Welding of Al alloy plates using a novel high-average-power pulsed CO2 laser

A novel high-average-power pulsed CO2 laser with a unique electrode structure is presented. The operation of a 5-kW transverse-flow CO2 laser with the preionized pulse-train switched technique results in pulsation of the laser power, and the average laser power is about 5 kW. The characteristic of this technique is switching the preionized pulses into pulse trains so as to use the small preionized power (hundreds of watts) to control the large main-discharge power (tens of kilowatts). By this means, the cost and the complexity of the power supply are greatly reduced. The welding of LF2, LF21, LD2, and LY12 aluminum alloy plates has been successfully achieved using this laser. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

Ti:sapphire laser pumped high average power laser crystal Nd:GGG with high efficiency output

High-quality neodymium doped GGG laser crystals have been grown by Czochralski (Cz) method. Results of Nd:GGG thin chip laser operating at 1.064 μm pumped by Ti:sapphire laser operating at 808 nm were reported. The slop efficiency was as high as 20%.

Influence of dew on biomass and photosystem II activity of cyanobacterial crusts in the Hopq Desert, northwest China

Dew is an important water source for desert organisms in semiarid and arid regions. Both field and laboratory experiments were conducted to investigate the possible roles of dew in growth of biomass and photosynthetic activity within cyanobacterial crust. The cyanobacteria, Microcoleus vaginatus Gom. and Scytonema javanicum (Kutz.) Born et Flah., were begun with stock cultures and sequential mass cultivations, and then the field experiment was performed by inoculating the inocula onto shifting sand for forming cyanobacterial crust during late summer and autumn of 2007 in Hopq Desert, northwest China. Measurements of dew amount and Chlorophyll a content were carried out in order to evaluate the changes in crust biomass following dew. Also, we determined the activity of photosystem II(PSII) within the crust in the laboratory by simulating the desiccation/rehydration process due to dew. Results showed that the average daily dew amount as measured by the cloth-plate method (CPM) was 0.154 mm during fifty-three days and that the crust biomass fluctuated from initial inoculation of 4.3 mu g Chlorophyll a cm(-2) sand to 5.8-7.3 mu g Chlorophyll a cm(-2) crust when dew acted as the sole water source, and reached a peak value of approximately 8.2 mu g Chlorophyll a cm(-2) crust owing to rainfalls. It indicated that there was a highly significant correlation between dew amounts and crust moistures (r = 0.897 or r = 0.882, all P < 0.0001), but not a significant correlation between dew and the biomass (r = 0.246 or r = 0.257, all P > 0.05), and thus concluded that dew might only play a relatively limited role in regulating the crust biomass. Correspondingly, we found that rains significantly facilitated biomass increase of the cyanobacterial crust. Results from the simulative experiment upon rehydration showed that approximately 80% of PSII activity could be achieved within about 50 min after rehydration in the dark and at 5 degrees C, and only about 20% of the activity was light-temperature dependent. This might mean that dew was crucial for cyanobacterial crust to rapidly activate photosynthetic activity during desiccation and rehydration despite low temperatures and weak light before dawn. It also showed in this study that the cyanobacterial crusts could receive and retain more dew than sand, which depended on microclimatic characteristics and soil properties of the crusts. It may be necessary for us to fully understanding the influence of dew on regulating the growth and activity of cyanobacterial crust, and to soundly evaluate the crust's potential application in fighting desertification because of the available water due to dew. (C) 2009 Published by Elsevier Ltd.

Effects of fish stocking on the zooplankton community structure in a shallow lake in China

Changes in the zooplankton community structure in relation to fishery practices in Lake Donghu, Wuhan, China were examined. The number of Protozoa species increased slightly, whereas the number of rotifers and crustaceans decreased from the 1960s to the 1990s. The total annual average densities of zooplankton increased 15-20 times in the 1990s compared with the 1960s. This increase was largely attributed to Protozoa, which contributed 93.4% by number of the total zooplankton density in 1991. Cladoceran densities decreased markedly from 1987. Changes in densities of rotifers and copepods were not evident. Trends in zooplankton biomass were similar to density. Large changes in zooplankton community structure coincided with markedly changes in concentration of chlorophyll a and transparency in Lake Donghu in 1987. The year 1987 seems to be the threshold year when the zooplankton community structure changed considerably. These changes were related to continuously increasing fish stock biomass in the lake. It was suggested that fish stocking and fish biomass should be a better managed for improvement of the quality of the lake's environment.

High average power and short pulse duration continuous wave mode-locked Nd : GdVO4 laser with a semiconductor absorber mirror

Passive mode locking of a solid-state Nd:GdVO4 laser is demonstrated. The laser is mode locked by use of a semiconductor absorber mirror (SAM). A low Nd3+ doped Nd:GdVO4 crystal is used to mitigate the thermal lens effect of the laser crystal at a high pump power. The maximum average output power is up to 6.5 W, and the pulse duration is as short as 6.2 ps. The optic-to-optic conversion efficiency is 32.5% and the repetition rate is about 110 MHz.

High-average-power and high-conversion-efficiency continuous wave mode-locked Nd : YVO4 laser with a semiconductor absorber mirror

A high-power continuous wave (cw) mode-locked Nd:YVO4 solid-state laser was demonstrated by use of a semiconductor absorber mirror (SAM). The maximum average output power was 8.1 W and the optic-to-optic conversion efficiency was about 41 %. At the maximum incident pump power, the pulse width was about 8.6 ps and the repetition rate was 130 MHz. Experimental results indicated that this absorber was suitable for high power mode-locked solid-state lasers. (C) 2006 Elsevier Ltd. All rights reserved.

A differential recursive scheme for suppression of Peak to average power ratio for OFDM

A differential recursive scheme for suppression of Peak to average power ratio (PAPR) for Orthogonal frequency division multiplexing (OFDM) signal is proposed in this thesis. The pseudo-randomized modulating vector for the subcarrier series is differentially phase-encoded between successive components in frequency domain first, and recursion manipulates several samples of Inverse fast Fourier transformation (IFFT) output in time domain. Theoretical analysis and experimental result exhibit advantage of differential recursive scheme over direct output scheme in PAPR suppression. And the overall block diagram of the scheme is also given.

Realization of GaAs/AlGaAs quantum-cascade lasers with high average optical power

Quasi-continuous-wave operation of GaAs/AlGaAs quantum-cascade lasers with high average optical power is demonstrated. Double X-ray diffraction has been used to investigate the quality of the epitaxial material. The compositional gradients and the interface quality are controlled effectively. The corrected average power of per facet about 17 mW and temperature tuning coefficient of the gain peak about 0.91 nm/K from 83 K to 140 K is achieved in pulse operation. Best value of threshold current density is less than 3.0 kA/cm(2) at 83 K. (C) 2005 Elsevier Ltd. All rights reserved.