VCSEL器件的设计、模拟、材料生长和微腔效应的研究

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

红光VCSEL与新的微腔形成机理的研究

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

基于VCSEL 的高速率并行光发射模块研究

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

VCSEL 的电、热、光特性分析及微机械可调谐Fabry-Perot 光学滤波器的研制

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

基于VCSEL 的甚短距离并行高速光传输系统研究

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

Parallel optical communication subsystem based on VCSEL - art. no. 67833I

A parallel optical communication subsystem based on a 12 channels parallel optical transmitter module and a 12 channels parallel optical receiver module can be used as a 10Gbps STM-64 or an OC-192 optical transponder. The bit error rate of this parallel optical communication subsystem is about 0 under the test by SDH optical transport tester during three hours and eighteen minutes.

VCSEL-based parallel optical transmission module

This paper describes the design process and performance of the optimized parallel optical transmission module. Based on 1x12 VCSEL (Vertical Cavity Surface Emitting Laser) array, we designed and fabricated the high speed parallel optical modules. Our parallel optical module contains a 1x12 VCSEL array, a 12 channel CMOS laser driver circuit, a high speed PCB (Printed Circuit Board), a MT fiber connector and a packaging housing. The L-I-V characteristics of the 850nm VCSEL was measured at the operating current 8mA, 3dB frequency bandwidth more than 3GHz and the optical output 1mW. The transmission rate of all 12 channels is 30Gbit/s, with a single channel 2.5Gbit/s. By adopting the integration of the 1x12 VCSEL array and the driver array, we make a high speed PCB (Printed Circuit Board) to provide the optoelectronic chip with the operating voltage and high speed signals current. The LVDS (Low-Voltage Differential Signals) was set as the input signal to achieve better high frequency performance. The active coupling was adopted with a MT connector (8 degrees slant fiber array). We used the Small Form Factor Pluggable (SFP) packaging. With the edge connector, the module could be inserted into the system dispense with bonding process.

Low threshold current density, low resistance oxide-confined VCSEL fabricated by a dielectric-free approach

We present the fabrication process and experimental results of 850-nm oxide-confined vertical cavity surface emitting lasers (VCSELs) fabricated by using dielectric-free approach. The threshold current of 0.4 mA, which corresponds to the threshold current density of 0.5 kA/cm(2), differential resistance of 76 Omega, and maximum output power of more than 5 mW are achieved for the dielectric-free VCSEL with a square oxide aperture size of 9 mu m at room temperature (RT). L-I-V characteristics of the dielectric-free VCSEL are compared with those of conventional VCSEL with the similar aperture size, which indicates the way to realize low-cost, low-power consumption VCSELs with extremely simple process. Preliminary study of the temperature-dependent L-I characteristics and modulation response of the dielectric-free VCSEL are also presented.

高功率VCSEL中应变补偿量子阱的理论设计

利用模型固体理论、k．p理论和Pikus-Bir理论，研究了InGaAs／GaAsP应变补偿量子阱，得出了较为简单通用的设计方法；进而研究了阱宽、InGaAs中In组分和GaAsP中P组分等参数对跃迁波长的影响。理论计算发现，与InGaAs／GaAs普通量子阱相比，InGaAs／GaAsP应变补偿量子阱能提供更深的载流子阱和更大的增益。按照提出的理论设计方法，研制了含InGaAs／GaAsP应变补偿量子阱的垂直腔面发射激光器（VCSEL），理论计算和实验结果相吻合。

MEMS可调谐VCSEL的研究进展

随着全光网络和DWDM系统的发展,MEMS可调谐VCSEL由于其优越的性能,有着相当广泛的应用前景.文章从结构差异上,将近几年来国际上的有关报道分成了单悬臂型,可变形介质模型,半对称腔型和掩埋隧道结型等四类,并对每一类型作了详细的介绍.

掩埋隧道结VCSEL芯片小信号等效电路模型

提出了适用于一种1.55μm掩埋隧道结垂直腔面发射激光器(VCSEL)芯片的小信号等效电路模型.等效电路的提出是基于半导体激光器速率方程以及VCSEL芯片结构,电路中各元件都有严格的物理意义.根据实验测得芯片的反射系数及传输参数,通过小信号等效电路仿真模拟,得到电路各元件参数值.不同偏置电流下,模拟结果与实验结果吻合都非常好,证明了该等效电路的有效性.

High Speed VCSEL-Based Parallel Optical Transmission Modules

Design and fabrication of a parallel optical transmitter are reported. The optimized 12 channel parallel optical transmitter,with each channel＇s data rate up to 3Gbit/s,is designed, assembled, and measured. A top-emitting 850nm vertical cavity surface emitting laser（VCSEL） array is adopted as the light source,and the VCSEL chip is directly wire bonded to a 12 channel driver IC. The outputs of the VCSEL array are directly butt coupled into a 12 channel fiber array. Small form factor pluggable （SFP） packaging technology is used in the module to support hot pluggable in application. The performance results of the module are demonstrated. At an operating current of 8mA, an eye diagram at 3Gbit/s is achieved with an optical output of more than 1mW.

键合界面阻抗对VCSEL的电、热学特性的影响

采用一电阻层来表征键合界面处的阻抗.通过求泊松方程、电流密度方程、载流子扩散方程以及有源层结压降方程自洽解的方法,计算了VCSEL的电势分布,进而求解热传导方程,得到VCSEL的温度分布.详细分析了键合界面阻抗对晶片键合结构垂直腔面发射激光器内部的电势分布、温度分布以及有源层中的注入电流密度、载流子浓度、结压降和温度沿径向分布的影响.

适用于光发射机设计的实用VCSEL小信号等效电路模型

提出了一个适用于发射机中驱动电路设计的具有较高计算效率、能准确反映不同频率时与驱动电路互作用的VCSEL等效电路模型．用曲线拟合的方法结合惠普网络分析仪测得的VCSEL反射参数S11，准确地得到了等效电路模型的各个参数值，并将此等效电路模型应用到设计驱动电路的模拟中．在标准EDA环境SPICE中对驱动电路和模型进行了协同模拟，与过于简化的VCSEL模型进行了对比，通过设计驱动电路芯片证明了此模型的有效性．