Effects of atmosphere visibility on performances of non-line-of-sight ultraviolet communication systems

Dependence of performances of non-line-of-sight (NLOS) solar-blind ultraviolet (UV) communication systems on atmosphere visibility is investigated numerically by correlating the propagation of UV radiation with the visibility. A simplified solar-blind UV atmospheric propagation model is introduced, and the NLOS UV communication system model is constituted based on the single scattering assumption. Using the model, numerical simulation is conducted for two typical geometry configurations and different modulation formats. The results indicate that the performance of the NLOS UV communication system is insensitive to variation of visibility in quite a large range, and deteriorates significantly only in very low-visibility weather, and is also dependent on the geometry configuration of the system. The results also show that the pulse position modulation (PPM) is preferable due to its high-power efficiency to improve the system performance. (c) 2007 Elsevier GmbH. All rights reserved.

图像处理在光路自动准直系统中的应用

光路自动准直系统应用于惯性约束聚变的高功率激光装置中的光束自动调整。图像处理是光路自动准直的关键技术之一。针对神光Ⅲ原型装置，结合阈值化、重心法、中值滤波和圆拟合等多种不同的图像处理方法设计了一套合理的准直方案，并且在模拟实验平台上进行了实验验证。实验结果表明，光路自动准直系统能够在15min之内顺利完成光路的自动调整，光束近场调整精度优于近场光斑的±0．5％，光束远场调整精度≤±0．3″，满足了原型装置的总体要求。

基于RS编码及网格编码调制的光PPM通信纠错技术

分析了RS（Reed-Solomon）纠错码和网格编码调制（Trellis Coded Modulation，TCM）技术在光脉冲位置调制通信中的应用．在此基础上，提出了以RS码作为外码，以网格编码调制技术作为内码，用于光脉冲位置调制通信的新编码方案，能以几乎不减少通信速率的优势，提高传统RS码系统在时变带限光信道中的通信性能．模拟研究了在不同空间光信道条件下，传统RS码的符号正确传输率和误码率，并对网格编码调制的编码增益、RS码与网格编码调制级联时的编码增益进行了仿真研究，证实了本方案的有效性．

测量薄膜微粗糙度的总积分散射仪

介绍了一种检测光学薄膜表面总积分散射（TIS）分布的总积分散射仪。对仪器的基本结构、理论基础、测量原理以及系统性能等进行了阐述，提出了抑制系统噪音和提高测量精度的有效措施。利用该仪器对K9基底上的银（Ag）膜和氧化锆（ZrO2）薄膜进行了测量，并根据标量散射理论得到了表面均方根（RMS）粗糙度。利用光学轮廓仪和原子力显微镜（AFM）分别测量了上述Ag膜和ZrO2薄膜的表面均方根粗糙度，并与总积分散射仪所得的粗糙度进行了比较。结果表明，根据测量的薄膜表面总积分散射计算得到的表面均方根粗糙度与光学轮廓仪及原子

Rate-equation-based circuit model of high-speed semiconductor lasers

Based oil rare equations of semiconductor laser, a symbolically-defined model for optical transmission system performance evaluation and network characterization in both time- and frequency domains is presented. The steady-state and small-signal characteristics, such as current-photon density curve, current-voltage curve, and input impedance, call be predicted from this model. Two important dynamic characteristics, second-order harmonic distortion and two-tone third-order intermodulation products, are evaluated under different driving conditions. Experiments show that the simulated results agree well with the published data. (c) 2007 Wiley Periodicals, Inc.

国产万亿次机群系统NPB性能测试分析

对3个国产万亿次机群系统进行了NPB性能测试分析,重点研究大规模并行处理时(处理器数目达到上千个)的性能特点和趋势.分析了不同的处理器、互连网络等系统配置对NPB性能的影响,发现NPB的8个程序在3个万亿次机器上的性能特点和表现并不一致,表明国产高性能机群在设计上正在逐渐走出同质化的趋势,向多样化发展.进一步分析表明,目前NPB程序的可扩展性可以达到几百个处理器,但尚不能达到上千个处理器,NPB程序能发挥出的系统峰值的百分比仍然徘徊在10%左右,机群系统的并行可扩展性和应用程序对机器运算潜能的利用还需要进一步提高.对于处理器数目达到上千个的万亿次机群系统来说,对集合通信和细粒度通信能力的支持亟需提高.

脉冲爆轰发动机的系统性能分析

采用简化的脉冲爆轰推进装置模型, 利用热循环效率分析方法, 推导了包含进气道总压恢复系数的热循环效率公式, 并在特定来流条件下, 考察了一个爆轰循环中进气道总压恢复系数和燃烧室初始温度对热循环效率和比冲的影响, 研究发现, 降低来流总压损失有助于提高热循环效率, 而提高燃烧室初始温度能更有效地提高热循环效率, 据此, 提出了多级重起爆脉冲爆轰发动机概念, 利用在突扩截面上解耦的爆轰波的前导激波去再次压缩工质, 进一步提高工质的热力学参数, 从而提高脉冲爆轰装置的热循环效率, 推导了此种构型PDE的热循环效率计算公式, 并对多级重起爆脉冲爆轰发动机进行了原理性论证, 研究结果表明, 多级重起爆方法提高了燃烧室的爆前温度, 从而有效地提高脉冲爆轰发动机热循环效率.最后, 关于出口工质的非完全膨胀的情况, 做了定性的阐述, 认为只有降低工质的出口压力, 才能更有效增加工质的出口动能, 从而提高热循环效率

Effect of cations in solution on the oxidation of methanol on the surface of platinum electrode

The effect of metal cations in solution on the oxidation of methanol on the electrode surface of platinum is a neglected aspect to direct methanol fuel cell (DMFC). In this paper, a smooth platinum electrode absorbing metal cations as the working electrode was applied to investigate the methanol oxidation with the cyclic voltammetry (CV) in 1.0 mol L-1 H2SO4. From the analysis of experiment, it is found that the cations, Li+, Ce4+, Mn2+, Ni2+, Cu2+, have some negative effect on the catalytic oxidation of methanol on the surface of platinum. The degree of the effect from different cations was analyzed.

洁净机器人手臂的转动惯量分析及运动控制

针对洁净机器人手臂的转动惯量对系统动态性能的影响,在利用动能公式分析得到其转动惯量与位置关系的基础上,提出了一种位置PI闭环加前馈参数整定的控制方法。该控制方法是由位置值实时得到转动惯量,再由转动惯量来实时整定PI参数。仿真结果表明了该控制方法能有效抑制转动惯量的变化对系统动态性能的影响,且简单可行。

基于合同网协议交互投标的动态调度方法研究

柔性制造系统使生产加工路径有很多可选性,所以调度系统必须考虑机器调度问题。分配规则调度是一种最基本、最具影响力的动态调度方法。然而,分配规则调度方法很少考虑机器顺序选择。兼顾工件选择和机器选择两方面,本文运用交互投标过程,构建基于合同网协议调度的协商规则。研究作业车间动态调度问题,提出并构建了5种合同网规则调度方法。通过实验分析结果表明,基于合同网交互投标模式的规则调度能够大大改善调度系统性能,提高设备的利用率和设备负荷平衡指标。

具有AGV和AS/RS的装配线物流系统分析

阐述了具有自动导引车(AGV)和自动存取系统(AS/RS)的物流系统的工作流程,建立了该类物流系统的排队网络模型,分析了系统的性能与系统设计参数之间的关系,为设计具有AGV和AS/RS的复杂物流系统提供依据。

载人潜器半物理虚拟仿真系统及其性能分析

为了缩短深海载人潜器控制系统的开发周期,测试系统性能,根据载人潜器的自身特点,构建和实现了载人潜器所有传感器、执行器设备模拟,以及潜器在海底实景的运动状态的半物理虚拟仿真系统。首先,以仿真系统的硬件架构和数据流程为基础,重点介绍了潜器设备模拟的软件体系结构;其次,在仿真平台上测试了各种网络数据的传输延迟,分析了其整体性能;最后,得出了潜器控制器设计的时间约束。现阶段整个系统已经开发成功,并投入运行到潜器控制系统的安装调试中。

Multi-sensors data acquisition and information fusion for manned submersible vehicle

本文介绍了一种用于载人潜水器的导航传感器的数据采集及信息融合技术。航行控制计算机通过基于工业以太网的数据通信系统对各传感器进行数据采集,采用卡尔曼滤波器完成对各传感器数据信息的融合,以便提高数据的精度和控制系统的性能,并将结果送给监控计算机,用于载人潜水器的姿态显示。

前馈在快速高精度数字随动系统中的应用

本文给出了一种具有前馈等值的二阶无静差数字随动系统的设计方法。按照这种设计方法,只要在计算的基础上适当地调整前馈系数和开环增益,即可得到满意的系统性能指标。

地震勘探三维可视化方法研究与实现

This thesis mainly studies the technologies of 3-D seismic visualization and Graphic User Interface of seismic processing software. By studying Computer Graphics and 3-D geological modeling, the author designs and implements the visualization module of seismic data processing software using OpenGL and Motif. Setting seismic visualization flow as the subject, NURBS surface approximation and Delaunay Triangulation as the two different methods, the thesis discusses the key algorithms and technologies of seismic visualization and attempts to apply Octree Space Partitioning and Mip Mapping to enhance system performance. According to the research mentioned above, in view of portability and scalability, the author adopts Object-oriented Analysis and Object-oriented Design, uses standard C++ as programming language, OpenGL as 3-D graphics library and Motif as GUI developing tool to implement the seismic visualization framework on SGI Irix platform. This thesis also studies the solution of fluid equations in porous media. 2-D alternating direction implicit procedure has been turned into 3-D successive over relaxation iteration, which possesses such virtues as faster computing speed, faster convergence rate, better adaptability to heterogeneous media and less memory demanding.