Study on the Performance of a Compact Compound Oil/Gas/Water Separator for Offshore Oil Industry

High-efficiency separation of the oil/gas/water mixtures is a significant issue in offshore oil industry. To reduce the total cost by means of reduction in weight and space compared with conventional separators, a novel compact compound oil/gas/water separator is developed. The research works on oil-gas-water separation by compound separating techniques is described in this paper. The innovative separator is a gravity settling tank with helical pipes within and T-shaped pipes outside. Both experiments and numerical simulations are presented to study the separating performance and efficiency of the helical pipes, which are the main part of the separator.

Multiphase Flow Measurement in the Offshore Oil Industry

In recent years, considerable research has been conducted into the development of a three-phase flowmeter suitable for use in an offshore environment, and oil/gas/water three-phase metering becomes an important aspect in multiphase flow measurement. This paper discusses the importance of three-phase flow measurement in offshore oil industry, describes the current development in this area, and points out the principal strategies which may be used to meter three-phase flow.

Ultrasonic Tomography and Its Applications in oilfield

UTT (Ultrasonic Tomography Tool) is widely used in the oil industry and can be used to inspect corrosion, casing wall damage, casing breakoff, and casing distortion in the well borehole with the maximum environment temperature being 125 °C, and the pressure being 60 MPa. UTT consists of tool head, upper centralization, electronic section, lower centralization, transmitters, and receivers. Its outer diameter is 4.6 cm and length is 320 cm. The measured casing diameter ranges from 60 mm to 254 mm. The tomography resolution is 512×512. The borehole measurement accuracy is 2 mm. It can supply 3D pipe tomography, including horizontal and vertical profile. This paper introduces its specification, measurement principle, and applications in oilfield.damage, casing breakoff, and casing distortion in the well borehole with the maximum environment temperature being 125 °C, and the pressure being 60 MPa. UTT consists of tool head, upper centralization, electronic section, lower centralization, transmitters, and receivers. Its outer diameter is 4.6 cm and length is 320 cm. The measured casing diameter ranges from 60 mm to 254 mm. The tomography resolution is 512×512. The borehole measurement accuracy is 2 mm. It can supply 3D pipe tomography, including horizontal and vertical profile. This paper introduces its specification, measurement principle, and applications in oilfield.

Gamma-Ray Attenuation Technique For Measuring Void Fraction In Horizontal Gas-Liquid Two-Phase Flow

The measurement of void fraction is of importance to the oil industry and chemical industry. In this article, the principle and mathematical method of determining the void fraction of horizontal gas-liquid flow by using a single-energy gamma-ray system is described. The gamma-ray source is the radioactive isotope of Am-241 with gamma-ray energy of 59.5 keV. The time-averaged value of the void fraction in a 50.0-mm i.d. transparent horizontal pipeline is measured under various combinations of the liquid flow and gas flow. It is found that increasing the gas flow rate at a fixed liquid flow rate would increase the void fraction. Test data are compared with the predictions of the correlations and a good agreement is found. The result shows that the designed gamma-ray system can be used for measuring the void fraction in a horizontal gas-liquid two-phase flow with high accuracy.

延安燕沟流域次降雨泥沙来源分析

延安燕沟流域属于水土流失治理的重点区,退耕还林(草)措施引起的生态环境改善和经济发展带动的山区道路建设压力对本地区侵蚀环境和侵蚀动力机制产生了巨大影响,坡面水土流失与道路水土流失对比关系发生了新变化。在坡面侵蚀得到初步治理的新环境下,道路侵蚀则上升为主要地位。依据燕沟流域2005年7月2日的5年一遇暴雨引起的不同土地利用类型下的侵蚀产沙监测结果,结合流域卡口站测得的流域产沙总量,分析各土地利用类型产沙量对流域总产沙量的贡献,并依据流域土地利用的演变,反演林草植被恢复与道路建设对流域泥沙来源的作用。研究结果表明:在次降雨条件下,道路的产沙强度为支道山路500 t/km2、干道山路3 163 t/km2、运油道路1万3500 t/km2,而农、林、草地的产沙强度为6~184 t/km2;道路产沙强度远大于农、林、草地的产沙强度:占流域面积1%的道路产沙量占总产沙量的42.3%,占流域面积70.5%的草地、灌木林地产沙量仅占流域的26.7%。退耕还林(草)措施使流域坡面产沙量大为降低,流域产沙量减少41.2%,但由于道路产沙量增加,抵消了减沙效益的58.0%,因此,黄土丘陵区植被恢复后,应将水土流失治理重点放在防止...

三维VSP技术的研究及应用

Today, because of high petroleum consumption of our country, society steady development and difficulty increase in new resources exploration, deep exploitation of the existing oilfield is needed. More delicate reservoir imaging and description, such as thin layer identification, interlayer exploitation monitoring, subtle structure imaging, reservoir anisotropy recognition, can provide more detail evidence for new development adjustment scheme and enhanced oil recovery. Now, the people have already realized the 3D VSP technique more effective than the general methods in solving these aspects. But VSP technique especially 3D VSP develop slowly due to some reasons. Carrying out the research of VSP technique, it will be very useful to the EOR service. 3D VSP techniques include acquisition、data processing and interpretation. In this paper, the author carried out some researches around acquisition and processing. The key point of acquisition is the survey design, it is critical to the quality of the data and it will influence the reservoir recognition as follows. The author did detailed researches on the layout pattern of shot point and geophone. Some attributes relate to survey design such as reflectivity, incidence angle, observation area, reflection points distribution, fold, minimum well source distance, azimuth angle and so on are studied seriously. In this geometry design of 3D-VSP exploration in deviated wells, the main problems to be solved are: determining the center position of shots distribution, the effect of shots missing on coverage areas and coverage times，locating the shots and receivers of multi-wells. Through simulating and analyzing, the above problems are discussed and some beneficial conclusions are drawn. These will provide valuable references to actual survey design. In data processing, researches emphasize on those relatively key techniques such as wavefield separation, VSP-CDP imaging, the author carried out deep researches around these two aspects. As a result, variant apparent slowness wavefield separation method developed in this article suit the underground variant velocity field and make wavefield separation well, it can overcome reflection bending shortage aroused by conventional imaging method. The attenuateion range of underground seismic wave is very important for amplitude compensation and oil/gas identification.In this paper, seismic wave attenuateion mechanism is studied by 3D-VSP simulateion and Q-inversion technique. By testing with seismic data, the method of VSP data attenuateion and relationship of attenuateion attribute variant with depth is researched. Also the software of survey design and data processing is developed, it fill the gap of VSP area in our country. The technique developed applied successfully in SZXX-A Oilfield、QKYY-B Oilfield、A area and B area. The good results show that this research is valuable, and it is meaningful to the VSP technique development and application of offshore oil industry and other areas in our country.

反射地震转换波成像方法研究

Multi-waves and multi-component get more and more attentions from oil industry. On the basis of existent research results, My research focuses on some key steps of OBC 4C datum processing. OBC datum must be preprocessed quite well for getting a good image. We show a flow chart of preprocess including attenuation of noise on multi-component datum、elimination ghost by summing P and Z and rotation of horizontal components. This is a good foundation for the coming steps about OBC processing. How to get exact converted point location and to analyze velocity are key points in processing reflection seismic converted wave data. This paper includes computing converted point location, analyzing velocity and nonhyperbolic moveout about converted waves. Anisotropic affects deeply the location of converted wave and the nonhyperbolic moveout. Supposed VTI, we research anisotropic effect on converted wave location and the moveout. Since Vp/Vs is important, we research the compute method of Vp/Vs from post-stack data and pre-stack data. It is a part of the paper that inversing anisotropic parameter by traveltime. Pre-stack time migration of converted wave is an focus, using common-offset Kirchhoff migration, we research the velocity model updating in anisotropic media. I have achieved the following results: 1) using continued Fractions, we proposed a new converted point approximate equation, when the offset is long enough ,the thomsen’s 2 order equation can’t approximate to the exact location of converted point, our equation is a good approximate for the exact location. 2) our new methods about scanning nonhyperbolic velocity and Vp/Vs can get a high quality energy spectrum. And the new moveout can fit the middle and long offset events. Processing the field data get a good result. 3) a new moveout equation, which have the same form as Alkhalifah’s long offset P wave moveout equation, have the same degree preciseness as thomsen’s moveout equation by testing model data. 4) using c as a function of the ratio offset to depth, we can uniform the Li’s and thomsen’s moveout equation in a same equation, the model test tell us choice the reasonable function C can improve the exact degree of Li’s and thomsen’s equation. 5) using traveltime inversion ,we can get anisotropic parameter, which can help to flat the large offset event and propose a model of anisotropic parameter which will useful for converted wave pre-stack time migration in anisotropic media. 6）using our pre-stack time migration method and flow, we can update the velocity model and anisotropic parameter model then get good image. Key words: OBC, Common converted Point (CCP), Nonhyperbolic moveout equation, Normal moveout correction, Velocity analysis, Anisotropic parameters inversion, Kirchhoff anisotropic pre-stack time migration, migration velocity model updating

叠前深度偏移速度模型的建立方法研究

Seismic exploration is the main tools of exploration for petroleum. as the society needs more petroleum and the level of exploration is going up, the exploration in the area of complex geology construction is the main task in oil industry, so the seismic prestack depth migration appeared, it has good ability for complex construction imaging. Its result depends on the velocity model strongly. So for seismic prestack depth migration has become the main research area. In this thesis the difference in seismic prestack depth migration between our country and the abroad has been analyzed in system. the tomographical method with no layer velocity model, the residual curve velocity analysical method based on velocity model and the deleting method in pre-processing have been developed. In the thesis, the tomographysical method in velocity analysis is been analyzed at first. It characterized with perfection in theory and diffculity in application. This method use the picked first arrivial, compare the difference between the picked first arrival and the calculated arrival in theory velocity model, and then anti-projected the difference along the ray path to get the new velocity model. This method only has the hypothesis of high frequency, no other hypothesis. So it is very effective and has high efficiency. But this method has default still. The picking of first arrival is difficult in the prestack data. The reasons are the ratio of signal to noise is very low and many other event cross each other in prestack data. These phenomenon appear strongly in the complex geology construction area. Based on these a new tomophysical methos in velocity analysis with no layer velocity model is been developed. The aim is to solve the picking problem. It do not need picking the event time contiunely. You can picking in random depending on the reliability. This methos not only need the pick time as the routine tomographysical mehtod, but also the slope of event. In this methos we use the high slope analysis method to improve the precision of picking. In addition we also make research on the residual curve velocity analysis and find that its application is not good and the efficiency is low. The reasons is that the hypothesis is rigid and it is a local optimizing method, it can solve seismic velocity problem in the area with laterical strong velocity variation. A new method is developed to improve the precision of velocity model building . So far the pattern of seismic prestack depth migration is the same as it aborad. Before the work of velocity building the original seismic data must been corrected on a datum plane, and then to make the prestack depth migration work. As we know the successful example is in Mexico bay. It characterized with the simple surface layer construction, the pre-precessing is very simple and its precision is very high. But in our country the main seismic work is in land, the surface layer is very complex, in some area the error of pre-precessing is big, it affect the velocity building. So based on this a new method is developed to delete the per-precessing error and improve the precision of velocity model building. Our main work is, (1) developing a effective tomographical velocity building method with no layer velocity model. (2) a new high resolution slope analysis method is developed. (3) developing a global optimized residual curve velocity buliding method based on velocity model. (4) a effective method of deleting the pre-precessing error is developing. All the method as listed above has been ceritified by the theorical calculation and the actual seismic data.

波动方程辛几何算法三维叠前深度偏移及其并行实现

Oil and scientific groups have been focusing on the 3D wave equation prestack depth migration since it can solve the complex problems of the geologic structure accurately and maintain the wave information, which is propitious to lithology imaging. The symplectic method was brought up by Feng Kang firstly in 1984 and became the hotspot of numerical computation study. It will be widely applied in many scientific field of necessity because of its great virtue in scientific sense. This paper combines the Symplectic method and the 3-D wave equation prestack depth migration to bring up an effectual numerical computation method of wave field extrapolatation technique under the scientific background mentioned above. At the base of deep analysis of computation method and the performance of PC cluster, a seismic prestack depth migration flow considering the virtue of both seismic migration method and Pc cluster has formatted. The software, named 3D Wave Equation Prestack Depth Migration of Symplectic Method, which is based on the flow, has been enrolled in the National Bureau of Copyright (No. 0013767). Dagang and Daqing Oil Field have now put it into use in the field data processing. In this paper, the one way wave equation operator is decompounded into a phase shift operator and a time shift operator and the correct item with high rank Symplectic method when approaching E exponent. After reviewing eliminating alias frequency of operator, computing the maximum angle of migration and the imaging condition, we present the test result of impulse response of the Symplectic method. Taking the imaging results of the SEG/EAGE salt and overthrust models for example and seeing about the imaging ability with complex geologic structure of our software system, the paper has discussed the effect of the selection of imaging parameters and the effectuation on the migration result of the seismic wavelet and compared the 2-D and 3-D prestack depth migration result of the salt mode. We also present the test result of impulse response with the overthrust model. The imaging result of the two international models indicates that the Symplectic method of 3-D prestack depth migration accommodates great transversal velocity variation and complex geologic structure. The huge computing cost is the key obstruction that 3-D prestack depth migration wave equation cannot be adopted by oil industry. After deep analysis of prestack depth migration flow and the character of PC cluster ,the paper put forward :i)parallel algorithms in shot and frequency domain of the common shot gather 3-D wave equation prestack migration; ii)the optimized setting scheme of breakpoint in field data processing; iii)dynamic and static load balance among the nodes of the PC cluster in the 3-D prestack depth migration. It has been proven that computation periods of the 3-D prestack depth migration imaging are greatly shortened given that adopting the computing method mentioned in the paper. In addition,considering the 3-D wave equation prestack depth migration flow in complex medium and examples of the field data processing, the paper put the emphasis on: i)seismic data relative preprocessing, ii) 2.5D prestack depth migration velocity analysis, iii)3D prestack depth migration. The result of field data processing shows satisfied application ability of the flow put forward in the paper.

油气藏自然电位异常与油气赋存的相关性研究

The Stack Spontaneous Potential (SSP) is a direct hydrocarbon location technology and a new hydrocarbon detection method with independent intellectual property. A subsurface hydrocarbon accumulation associated with the upward hydrocarbon micro seepage induces a relatively strong negative potential abnormal zone, of which the anomaly can be measured on the surface with specially designed instruments through careful field measuring procedures. With special software programmed according to a unique geochemical and geophysical model, the original data are analyzed, processed and interpreted on the computer, and then on a series of resulting anomaly distribution maps and/or profiles, the favorable surface locations of the hydrocarbon accumulations can be easily identified. The study of the SSP has been started since 1989, and especially from 1996 to 1997, both profile and area tests were conducted in the Daqing Oilfield. On the testing line of 15kms, there are 6 wells in total, among which some are oil-producing wells, and some are water-producing wells. The final matching ratio of the favorable oil well locations and the possible water well locations predicted by the SSP to those of known wells was up to 83 percent. In the area test, of which the acreage is 800 km2, the matching ratio compared with the existing wells was 87 percent; furthermore, regarding to wells subsequently drilled after the test, the matching ratio was 85 percent. The matching ratio in the development area is more about 10 percent than those of in exploration area. The reason is that, comparing the exploration area, the development area acreage is less and the container rocks are more simplex. In development area there is not so much interference of SSP also. Since 1997 the SSP has been tested and applied all over China to a number of hydrocarbon bearing basins and known oil fields, including the Daqing, Jiangsu, Changqing, Shengli, Nanyang, Jianghan and Zhongyuan Oilfields, only to name a few. The SSP surveys in total areas of over 10,000km2 in more than 30 regions in China so far have been completed in various exploration and development stages, the satisfactory outcomes of which have further evidenced that the dependence between the SP anomaly and abundance of hydrocarbon. Up to date, a substantial amount of successful tests and actual surveys finished in exploration and development practices have evidenced that the SSP is significantly more reliable in comparison with any other similar direct hydrocarbon indication technique generally known to the oil industry, such as the Redox. The SSP can be applied to search for almost all kinds of hydrocarbon accumulations, regardless of the type of traps, such as structural, stratigraphic, buried hill traps, and so on; however, it is interesting to be noted that the SSP seems to be particularly effective in detecting the stratigraphic oil traps according to our practices. On the other hand, there is virtually no surface geographical constrains in terms of field data acquisition, except for those water covered areas, because of the inherent characteristics of the technology itself. Furthermore, utilizing the SSP requires no special considerations to subsurface geological conditions in regard to formation resistivity, since the SSP measurements will not be influenced by either overly high or overly low resistivity of formations lying above the hydrocarbon accumulations. There are two kind of theory, of which, as we know one is called hypbyssal theory such as "Redox"[61 the other is call plutonic theory such as cracking of hydrocarbon [8][9] and natural polarization [3], to describe the mechanism of SP anomaly of oil reservoir and to indicate that the dependence between the SP abnormality and abundance of hydrocarbon has be existed theoretically/The quantitative dependence, which has not been founded due to the complicity of container rocks, be discovered during the exploration and development practices is the crux to the quantitative analysis of SP Anomaly processing. Based on the thorough study of the complex of collector rocks, every kind of thickness of collector rock can be conversed to be a standard effective thickness; the thickness is called apparent effective thickness (AET). The conversation coefficient (ai, 1=1,2,3) could be determined by the variety of every collector rock storability (CRS). The discoveration of quantitative: dependence between AET and the amplitude of SSP, in the practices of exploration and development, is a promotion for the SSP supplied in the oil exploration, and make the data analysis forward to the quantitative stage.