展宽器元件失调及带通分析

通过光线追迹法给设计的反射式单光栅展宽器建立了一个数学计算模型。利用这个数学模型计算和分析了元件失调对反射式单光栅展宽器二阶色散量和输出光束发散角的影响，并考虑了反射式单光栅展宽器中衍射光栅和球形凹面镜的尺寸与展宽器带通的关系。发现当平面反射镜M1的纵向偏离角为0．2°时．展宽器的二阶色散量最大，偏离角大于或小于0．2°时，展宽器的二阶色散量随之减小；得到了元件失调会增加输出光束发散角的结论；并发现展宽器中衍射光栅和球形凹面镜尺寸的有限大小对带通有限制作用。提出了利用反射镜M1纵向的适当偏离增大展宽器二阶

部分端面抽运板条激光器腔镜倾斜问题研究

部分端面抽运的板条激光器是一种新型固体激光器．配合混合腔可以实现在大功率下保持高光束质量的激光振荡输出。谐振腔的腔镜倾斜是影响激光器输出特性的重要因素，快速傅里叶方法是一种快捷有效的计算方法，利用此方法模拟了腔镜倾斜对近场相位分布和远场光强分布的影响，并分析了光束质量的变化。理论分析表明，腔镜的小角度倾斜对近场相位影响较大，但对远场光强空间分布影响不大；随着倾斜角度不断增大，远场发散角和光束腰宽度也增大，光束质量虽然存在恶化的趋势，但光束质量因子肝值仍然较小，离轴非稳腔仍能保持高光束质量的输出。

立方反射镜失调特性的研究

结合理想坐标系下立方镜镜面微小倾斜后其三个平面法线坐标，利用刚体微量转动的反射法线向量公式，获得非理想立方镜反射矩阵；为了研究在光斜入射时镜面倾斜对出射光方向的影响，利用立方镜绕顶点旋转等效于光斜入射的方法，计算出光束夹角δ与单一镜面偏差角ε和立方镜旋转角θ之间的关系式；对于理想情况下的立方镜，利用几何光学可以证明出射光与入射光不但平行，而且过顶点作任意截面交于两光线所得的两个交点关于顶点对称，从而计算出立方镜绕顶点以外任意轴旋转造成出射光束相对原出射光的偏移量与旋转角关系式，理论计算值与实验数据吻合得很

InnoSlab混合腔输出光束质量的理论研究

对InnoSlab Laser用混合腔的输出光束质量问题从热透镜效应和腔镜的不对准两个方面的影响进行理论分析,并从远场光强分布、远场发散角、光腰半径、光束质量因子M2值和桶中功率曲线等几个角度进行了讨论,特别是离轴非稳腔方向上腔镜倾斜对光束质量的影响,利用M2值和PIB曲线两个参数共同评价非稳腔的光束质量,对目前并无统一标准的非稳腔光束质量评价问题提供了有意义的参考.

High performance of 1.55 mu m DFB integrated with vertically tapered self-aligned spot-size converter

A new type of self-aligned spotsize converter (SSC) integrated 1.55 mum DFB lasers had been proposed in this article. The upper optical confinement layer and the butt-coupled tapered thickness waveguide were regrown simultaneously, which not only offered the separate optimization of the active region and the integrated SSC, but also reduced the difficulty of the butt-joint selective regrowth. The vertical and horizontal far field angles were 9degrees and 12degrees respectively, the 1- dB misalignment tolerance were both 3.6 and 3.4 mum. The directed coupling efficiency to tapered single mode fiber was 48%.

An experimental study of ultrashort pulsed ytterbium-doped fibre laser and amplifier

We report the generation of ultrashort pulses in ytterbium-doped fibre oscillator emitting around 1.05 mum at a repetition rate of 17.6MHz. A diode laser with single silica fibre at 976 nm pumps the ytterbium fibre laser, the all-fibre picosecond pulsed oscillator has excellent stability and compact size, and freedom from misalignment. After amplifying, pulse energy of 3.4 nJ and an average power of 60mW are obtained. The compression is obtained with a grating pair out of the cavity. The compressor produces 307 fs with the peak power 5.47 kW. A practical fibre-based source with good performance is thus demonstrated.

Design of a Tapered Lens for Semiconductor Laser to Single-Mode Fiber Coupling

The theoretical investigation of the coupling efficiency of a laser diode to a single mode fiber via a hemispherical lens on the tip of the tapered fiber in the presence of possible transverse offset and angular mismatch is reported.Without the misalignment,coupling efficiency increases with the decreasing of taper length.With the misalignment,this relation is that the coupling efficiency decreases with each kind of offset.

Narrow-beam divergence 1.55μm laser diodes with integrated self-aligned spotsize conVerter

This paper describes the high performance of narrow-beam divergence spot size converter (SSC) integrated separately confined heterostructure (SCH) LD. The upper optical confinement layer (OCL) and the butt-coupled tapered thickness waveguide were regrown simultaneously, which not only offered the separated optimization of the active region and the integrated spotsize converter, but also reduced the difficulty of the butt-joint selective regrowth. The threshold current was as low as 5.4 mA, the output power at 55 mA was 10.1 mW, the vertical and horizontal far field divergence angles were as low as 9°and 15°, and the 1-dB misalignment tolerances were 3.6 and 3.4μm, respectively.

1.5μm Self-Aligned Spotsize Converter Integrated DFB Fabricated by Selective Area Grown MOVPE

High performance 1.57μm spotsize converter monolithically integrated DFB is fabricated by the technique of self-aligned selective area growth. The upper optical confinement layer and the butt-coupled tapered thickness waveguide are regrown simultaneously, which not only offeres the separated optimization of the active region and the integrated spotsize converter, but also reduces the difficulty of the butt-joint selective regrowth. The threshold current is as low as 4.4mA. The output power at 49mA is 10.1mW. The side mode suppression ratio (SMSR) is 33.2dB. The vertical and horizontal far field divergence angles are as small as 9° and 15° respectively, the 1dB misalignment tolerance are 3.6μm and 3.4μm.

Spotsize Converter Integrated DFB Laser Diode Using Selective Area Growth of MOCVD

The characteristics of thickness enhancement factor and bandgap wavelength of selectively grown In-GaAsP are investigated. A high thickness enhancement factor of 2.9 is obtained. Spotsize converter integrated DFB lasers are fabricated by using the technique of SAG. The threshold current is as low as 10.8mA. The output power is 10m W at 60mA without coating and the SMSR is 35.8dB. The vertical far field angle (FWHM) is decreased from 34 °to 9 °. The tolerance of 1dBm misalignment is 3.4μm vertically.

1.5 mu m DFB integrated with vertical tapered spotsize converter fabricated by selective MOVPE

1.5 mu m DFB LD butt-joint integrated with vertical tapered spotsize converter was fabricated by LP-MOVPE. The vertical far field angle (FWHM) was decreased from 34degrees to 10degrees the threshold currents was as low as 19.8mA, the output power was 9.6mw at 100mA without HR coating and the SMSR was 35.8dB. The 1-dBm misalignment tolerance was 3.2 mu m, while the counterpart of the device without SSC was 2.2 mu m.

激光拼焊错边产生与预测建模方法

错边是评定激光拼焊质量的一个非常重要的指标,薄板构件错边的控制是激光拼焊中一个难题。针对国内首条全自动激光拼焊设备,对错边的产生以及控制方法进行了深入研究,经过大量试验确定了影响错边大小的几个主要因素,板材自身物理变形、压紧力大小与均匀性、压紧横梁变形、支撑底板平面度误差以及焊接变形的影响。通过分析以上因素对错边的影响以及各个因素之间相互关系,建立了错边预测的数学模型。试验验证了模型的正确性,从而为确定错边产生原因,提高焊接质量提供了一个有效的理论指导。