High-density gold nanoparticles supported on a [Ru(bpy)(3)](2+)-doped silica/Fe3O4 nanocomposite: Facile preparation, magnetically induced immobilization, and applications in ECL detection

A large-scale process combined sonication with self-assembly techniques for the preparation of high-density gold nanoparticles supported on a [Ru(bpy)(3)](2+)-doped silica/Fe3O4 nanocomposite (GNRSF) is provided. The obtained hybrid nanomaterials containing Fe3O4 spheres have high saturation magnetization, which leads to their effective immobilization on the surface of an ITO electrode through simple manipulation by an external magnetic field (without the need of a special immobilization apparatus). Furthermore, this hybrid nanomaterial film exhibits a good and very stable electrochemiluminescence (ECL) behavior, which gives a linear response for tripropylamine (TPA) concentrations between 5 mu m and 0.21 mM, with a detection limit in the micromolar range. The sensitivity of this ECL sensor can be easily controlled by the amount of [Ru(bpy)(3)](2+) immobilized on the hybrid nanomaterials (that is, varying the amount of [Ru(bpy)(3)](2+) during GNRSF synthesis).

Variation characteristics and ecological risk of heavy metals in the south Yellow Sea surface sediments

Eight cruises were conducted on the south Yellow Sea (SYS) from 1998 to 2005. Variations and the potential ecological risk of heavy metals were studied using the survey data collected during October 2003. The metal content (except for As) was high in the central area where the fine grain size sediments were dominant, and low inshore area where more coarse sediments were present. This suggested that grain size was important in determining distributions of heavy metals. In some local areas, other influencing factors, such as organic content, sedimentation rate, burial efficiency and metal's existing form were discussed. The annual averages of metals showed a stable trend with appreciable fluctuations in 8 years. Using potential ecological risk index (E (RI)) to evaluate the integrated pollution effect of heavy metals, 38.7% of the investigated area was in a moderate degree of contamination, while 77.8% was under moderate ecological risk. However, no distinct correlation was found between E (RI) and plankton biomass. In conclusion, the sediment quality of SYS was good, and the ecological risk was low in general.

Directly synthesized strong, highly conducting, transparent single-walled carbon nanotube films

We report the direct synthesis of strong, highly conducting, and transparent single-walled carbon nanotube (SWNT) films. Systematically, tests reveal that the directly synthesized films have superior electrical and mechanical properties compared with the films made from a solution-based filtration process: the electrical conductivity is over 2000 S/cm and the strength can reach 360 MPa. These values are both enhanced by more than 1 order. We attribute these intriguing properties to the good and long interbundle connections. Moreover, by the help of an extrapolated Weibull theory, we verify the feasibility of reducing the interbundle slip by utilizing the long-range intertube friction and estimate the ultimate strength of macroscale SWNTs without binding agent.

H4 exponential finite-difference scheme for convective diffusion-equations

Perturbations are applied to the convective coefficients and source term of a convection-diffusion equation so that second-order corrections may be applied to a second-order exponential scheme. The basic Structure of the equations in the resulting fourth-order scheme is identical to that for the second order. Furthermore, the calculations are quite simple as the second-order corrections may be obtained in a single pass using a second-order scheme. For one to three dimensions, the fourth-order exponential scheme is unconditionally stable. As examples, the method is applied to Burgers' and other fluid mechanics problems. Compared with schemes normally used, the accuracies are found to be good and the method is applicable to regions with large gradients.

贡嘎山植物小枝功能性状在不同生活型和不同海拔间的比较研究

植物功能生态学研究不仅提供了植物生理生态学与生态系统生态学的连接，还为植物种群生活史对策研究提供了材料。Westoby 等 (2002) 提出了利用植物功能性状变量的主导维度来确定和量化植物生活史的生态适应策略。在他们所提出四个主导维度中，叶大小－小枝大小是研究相对较少的一维；其内部各组分的关系、对环境的响应，以及与其它重要维度的关系，目前的理解非常有限。 本研究以贡嘎山不同海拔不同功能群物种为研究对象，采用种间比较和系统发生独立性比较等研究方法，系统研究了植物的功能特征及其相关性在不同生境及不同功能群间的差异，旨在分析不同功能群物种的叶大小－小枝大小的成本和收益。其研究结果将有助于我们理解植物生活史对策的进化，进而理解物种共存和维持物种多样性的机制。主要研究结果如下： 1. 叶大小－小枝大小关系 小枝茎横截面积与单叶面积和总叶面积均呈异速生长关系，即总叶面积和单叶面积的增加比茎横截面积的增加速度快。但是，总叶面积和叶片干重的增加却基本上与小枝茎干重的增加等速。系统发生独立性比较研究的结果与此相一致。表明，在某一给定的茎投入时，至少大叶大枝物种不比小叶小枝物种在支撑叶面积和叶片干重方面具有优势。同时，在某一给定的小枝茎投入时，常绿阔叶物种比落叶阔叶物种支撑更少的叶面积。在茎干重与总叶面积的关系中，落叶复叶物种比落叶单叶物种具有更高的y轴截距，表明复叶物种比单叶物种在展叶面积方面更有效。复叶物种与单叶物种相比，通常具有较大的叶大小和小枝大小。 2. 叶大小－叶数量关系 叶大小与数量间在不同的叶片习性、不同的叶片形态以及不同的生境类型的物种间均存在稳定的负的等速生长关系，且这种关系在系统发生独立性比较时依然成立。然而，在某一给定的出叶强度 (单位小枝的叶数量) 时，常绿阔叶物种比落叶物种具有更小的叶面积。而在给定体积基础上的出叶强度时，落叶复叶物种的叶面积显著大于落叶单叶物种，且复叶物种比单叶物种具有更大的叶大小和更小的出叶强度。但是，叶大小与数量间的关系在不同的海拔间并没有显著的差异。 3. 小枝大小－总叶面积关系 在不同的生活型或不同的生境下，小枝上总叶面积与茎干重和小枝干重均呈正的异速生长关系，且斜率显著小于1.0，表明小枝上总叶面积的增加都不能赶上小枝及茎大小的增加。这种“收益递减”表明随着小枝干重的增加，光截取的收益递减。此外，叶面积比 (总叶面积与小枝干重的比值) 与单叶干重呈显著负相关关系，系统发生独立性比较的结果与此相一致。根据以上结果，可以推测，大叶的物种在质量较好的生境中出现，而群落内部小枝茎的寿命较长的物种可以拥有较大的叶片。 4. 叶片色素浓度－LMA关系 随着海拔的升高，阔叶木本植物和草本植物的叶片色素浓度减少，叶绿素a/b和类胡萝卜素/叶绿素比值以及比叶重 (LMA) 增加。然而，在草本植物中的色素浓度、色素比值和LMA的变化比阔叶木本植物的更明显。同时，LMA与叶片色素浓度呈负相关关系，但是在落叶物种中的LMA对色素浓度的影响比常绿阔叶物种更强烈。总之，草本植物的叶片特征对海拔梯度的变化似乎比木本植物更敏感，LMA对叶片色素的保护作用在落叶物种中比在常绿阔叶物种显得更重要。这些结果表明不同生活型物种可能采取不同的保护机制来降低叶绿体器官的损伤和增加他们的碳获取能力。 Studies on plant functional ecology not only bridge plant eco-physiology and ecosystem functioning, but also enrich plant population biology. As pointed out by Westoby et al (2002), plant life history strategies can be identified and quantified by four leading dimensions of variations in plant functional traits, i.e., seed size/output, leaf mass per area and leaf life span, plant height, and leaf size-twig size. Compared to the other dimensions, the cost/benefit of the leaf size-twig size spectrum has scarcely been analyzed in relation to environmental gradients and life form types, and the adaptive significance of this spectrum is not fully understood. In the present study, the relationships between functional traits of plant twigs are determined for the species with different life forms along an altitudinal gradient of Gongga Mountain with both cross-species analysis and evolutionary divergence analysis. The primary objective of this study is to examine the cost/benefit of leaf size-twig size in plants. The study results are supposed to provide insights into the understanding of the mechanism of species coexistences. The results are shown in the following. 1. The relationship between leaf size and twig size Twig cross-sectional area allometrically scaled with both individual leaf area and total leaf area supported by the twigs. However, the increase in total lamina mass/area was generally proportional to the increase in stem mass. These correlations between trait variations were significant in both interspecies analysis and phylogenetically independent comparison (PIC) analysis, which indicated that thick-twigged/large-leaved species, at least, do not have an advantage in supporting leaf/lamina area and lamina mass for the same twig stem investment than thin-twigged/ small-leaved species. Meanwhile, the evergreen broad-leaved species supported a smaller leaf area for the same twig stem investment in terms of both cross-sectional area and stem mass than the deciduous species. The deciduous compound-leaved species have a higher y-intercept in the scaling relationship of twig stem mass versus total leaf area than the deciduous simple-leaved species, indicating that compound-leaved species were more efficient in displaying leaf area. The compound-leaved species were larger in both leaf size and twig size than their counterpart in the present study. 2. The relationship between leaf size and leaf number Significantly negative and isometric scaling relationships between leaf size and leafing intensity (leaf number per twig mass or volume) were found to be consistently conserved across species independent of leaf habit, leaf form and habitat type. The negative correlations between leaf size and leafing intensity were also observed across correlated evolutionary divergences. However, leaf area was smaller in the evergreen broad-leaved species at a given leafing intensity than in the deciduous species. The deciduous compound-leaved deciduous species were higher in leaf area than deciduous simple-laved species at a given volume-based leafing intensity. Moreover, the compound-leaved deciduous species were larger in leaf size but smaller in leafing intensity than their simple counterparts. No significant difference was found in the scaling relationships between altitudes. 3. The relationship between twig size and total leaf area Leaf area was found to scale positively and allometrically with both stem and twig mass (stem mass plus leaf mass) with slopes significantly smaller than 1.0, independent of life form and habitat type, indicating that the increase in total leaf area fails to keep pace with increasing twig size and stem size. This ‘diminishing returns’ suggests that the benefit of light intercept decreased with increasing twig mass. Moreover, the leaf area ratio (the ratio of total leaf area to stem or twig mass) correlated negatively with individual leaf mass. The results of PIC were consistent with the correlations. According to the results, it is speculated that large-leaved species may be favored when habitat is good and when stem longevity are long within community. 4. The relationship between leaf pigment concentrations and leaf mass per area With increasing altitude, the concentrations of pigments decreased, but the ratios of chlorophyll a/b and carotenoid/chlorophyll, and LMA increased, in both the broad-leaved woody species and herbaceous species groups. However, the changes in the pigment concentrations, ratios and LMA were more profound in the herbaceous species than in the woody species. In addition, pigment concentrations were negatively correlated with LMA in each life form type and in the pooled dataset. However, the LMA effect on leaf pigment concentrations was more profound in the deciduous species than in the evergreen braode-leaved species. In general, herbaceous species seemed more sensitive to the increasing altitude compared to woody species, and LMA seemed to be a more important mechanism for protecting leaf pigments in deciduous species than in evergreen broad-leaved species. These results suggested that the species with different life forms may employ different protective mechanisms to decrease the chloroplast apparatus damage and increase their carbon gain.

Application of rotifer Brachionus plicatilis in detecting the toxicity of harmful algae

The toxicity of seven major HAB (harmful algal bloom) species/strains, Prorocentrum donghaiense, Phaeocystis globosa, Prorocentrum micans, Alexandrium tamarense (AT-6, non-PSP producer), Alexandrium lusitanicum, Alexandrum tamarense (ATHK) and Heterosigma akashiwo were studied against rotifer Brachionus plicatilis under laboratory conditions. The results show that P. donghaiense, P. globosa, P. micans, A. tamarense (AT-6), or A. lusitanicum could maintain the individual survival and reproduction, as well as the population increase of the rotifer, but the individual reproduction would decrease when exposed to these five algae at higher densities for nine days; H. akashiwo could decrease the individual survival and reproduction, as well as population increase of the rotifer, which is similar to that of the starvation group, indicating that starvation might be its one lethal factor except for the algal toxins; A. tamarense (ATHK) has strong lethal effect on the rotifer with 48h LC50 at 800 cells/mL. The experiment on ingestion ability indicated by gut pigment change shows that P. donghaiense, P. globosa, P. micans, A. tamarense (AT-6) and A. lusitanicum can be taken by the rotifers as food, but A. tamarense (ATHK) or H. akashiwo can be ingested by the rotifers. The results indicate that all the indexes of individual survival and reproduction, population increase, gut pigment change of the rotifers are good and convenient to be used to reflect the toxicities of HAB species. Therefore, rotifer is suggested as one of the toxicity testing organisms in detecting the toxicity of harmful algae.

高邮凹陷陈堡及陈堡东地区油气成藏规律研究

With the development of petroleum exploration in Gaoyou Depression, both old and new areas have been the active exploration targets, so the study of petroleum accumulation is significant to the petroleum exploration in the study area and the integrated oil and gas accumulation theory. Based on hydrocarbon accumulation theory and systematical research methods and combined with the structural characteristics of Gaoyou Depression, Chenbao and East of Chenbao were selected as the study areas in this dissertation, oil and gas migration pathways, accumulation periods, as well as accumulation models were studied, and favorable exploration targets were proposed. There develop three sets source rocks, which are Tai-2 Member, Fu-2 Member and Fu-4 Member respectively. Tai-2 Member is the predominant source rock in the eastern part. Fu-2 Member mainly occurs in the northern slope, while Fu-4 Member develops in the deep depression. In the study area, oil mainly comes from Fu-2 Member of Liuwushe subsag. The lower limit of TOC is 0.4%, and active source rock mostly distributed in the south fault-step zone. The source rock in Liuwushe subsag began to generate hydrocarbon in the late of Dainan depositional stage and the threshold was 2300m. The macro and micro characteristics of reservoirs and the reservoir heterogeneity characteristics of the Fu-1 Member were studied systematicly. The results show that Fu-1 Member, which has better reservoir properties, are medium porosity-medium permeability reservoir. The reservoir permeability has good correlation with porosity connectivity. The reservoirs have strong dissolution, pores are mainly thin to medium throat, and throat radii are distributed concentratedly, the sorting is good and pore structures are homogeneous. Sandstone reservoirs whether in the plan view, interlayer or in layers have a certain degree of heterogeneity, in particular, the heterogeneity in layers directly affect and control the oil and gas migration and accumulation. By analyzing the lithology correlation of the fault walls, shale smear, cross section stress, the configuration of fracture active periods and hydrocarbon generation and expulsion periods and fuzzy comprehensive evaluation, the main faults sealing were evaluated. The results show that the faults in Chenbao and East of Chenbao had poor sealing properties in Sanduo period and could be used as the migration pathways at that time. After Sanduo period, the tectonic stress fields in the area changed largely, and, consequently, the fault properties converted from tensional shear to compressive shear, the faults changed progressively from close to open, so the faults sealing became better and were conducive to the preservation of oil and gas reservoirs. According to the seismic event suspension modes and profile configurations above and under the unconformities, combined with tectonic evolutions of the study areas, the unconformity types can be classified into truncation unconformity, overlapped unconformity and parallel unconformity and the distribution characteristics of unconformities in the plan view was also studied. The unconformity structure was divided into basal conglomerate, weathered clay and semi-weathered layer vertically in the study area and this kind of structure make unconformities to be effective oil and gas migration pathways and is significant to hydrocarbon accumulation in a parts of areas. With the analyses of typical oil and gas reservoirs in the study area, combined with the research results of pathway systems, hydrocarbon accumulation models were established and the oil and gas accumulation laws in Chenbao and East of Chenbao analyzed. The oil and gas came from Liuwushe subsag and Liuliushe subsag. The oil and gas from Liuwushe subsag mainly migrated from the structural high parts into the fault-step zone along strata in northeast direction, a part of them migrated upward into the fault-step zone and the Wubao low uplift along Wu-1 Fault in northeast direction. The oil and gas from Liuliushe subsag mainly migrated into the upper reservoirs through Wu-2 fault, and lesser oil and gas migrated into the fault-step zone because of the controls of cross-section orientation, depression center and the hydrocarbon formation tendency. The favorable exploration targets in Chenbao and East of Chenbao have been concluded: the southern fault-step zone is a favorable oil and gas accumulation zone of Liuwushe subsag, and they are fault block reservoirs where fault acted as the barriers, the main target intervals are Fu-1 Member and Fu-3 Member in palaeocene; Oil and gas in the middle and northern fault-step zone mainly laterally migrated from the south areas, and the main target interval is Fu-3 Member in palaeocene; Fu-1 Member and the reserviors above the Wubao subsag are still the focuses in future explorations. The results of this study have important guiding significance for the future oil and gas exploration.

河流成因储层沉积微相与剩余油分布及形成机理研究

Based on the study of fluvial sandstone reservoir in upper of Guantao group in Gudao and Gudong oilfields, this paper first introduces A.D.Miall's(1996a) architectural-element analysis method that was summarized from ground outcrop scale into the reservoir formation research of the study area, more subtly divides sedimentary microfacies and establishes sedimentary model of research area.on this base, this paper summarizes the laws of residual oil distribution of fluvial formation and the control effect of sedimentary microfacies to residual oil distribution, and reveals residual oil formation mechanism. These results have been applied to residual oil production, and the economic effect is good. This paper will be useful for residual oil research and production and enhancement of oil recovery in similar reservoir. The major conclusions of this paper are as follows. 1. Using the architectural-element analysis method to the core data, a interfacial division scheme of the first to the dixth scale is established for the studied fluvial formation. 2.Seven architectural-elements are divided in upper of Guantao group of study area. The sandstone group 5～1+2 of Neogene upper Gutao group belongs to high sinuous fine grain meandering river, and the sandstone group 6 is sandy braided river. 3. Inter layer, the residual oil saturation of "non-main layer" is higher than "main layer", but the residual recoverable reserve of former is larger. Therefore, "main layer" is the main body of residual oil distribution. The upper and middle part of inner layer has lower permeability and strong seeping resistance. Addition to gravity effect in process of driving, its driving efficiency is low; residual oil saturation is high. Because of controlling of inside non-permeable interlayer or sedimentary construction, the residual oil saturation of non-driving or lower driving efficiency position also is high. On plane, the position of high residual oil saturation mostly is at element LV, CS, CH (FF), FF etc, Which has lower porosity and permeability, as well as lens sand-body and sand-body edge that is not controlled by well-net, non-perfect area of injection and production, lower press difference resort area of inter-well diffiuent-line and shelter from fault, local high position of small structure. 4.Microscopic residual oil mainly includes the non-moved oil in the structure of fine pore network, oil in fine pore and path, oil segment in pore and path vertical to flow direction, oil spot or oil film in big pore, residual oil in non-connective pore. 5.The most essential and internal controlling factor of fluvial formation residual oil distribution is sedimentary microfacies. Status of injection and production is the exterior controlling factor of residual oil distribution. 6. The controlling effect of formation sedimentary microfacies to residual oil distribution indicates inter-layer vertical sedimentary facies change in scale of injection and production layer-series, planar sedimentary face change and inner-layer vertical sedimentary rhythm and interbed in single layer to residual oil distribution. 7. It is difficult to clear up the inter-layer difference in scale of injection and production layer-series. The using status of minor layer is not good and its residual oil saturation is high relatively. It is obvious that inter-layer vertical sedimentary facies changes control inter-layer residual oil distribution at the same or similar conditions of injection and production. For fluvial formation, this vertical sedimentary facies change mainly is positive gyration. Namely, from down to top, channel sediment (element CHL, LA) changes into over-bank sediment (element LV, CR, CS). 8. In water-injection developing process of transverse connecting fluvial sandstone oil formation, injection water always comes into channel nearby, and breaks through along channel and orientation of high pressure gradient, does not expand into side of channel until pressure gradient of channel orientation changes into low. It brings about that water-driving status of over-bank sedimentary element formation (LV, CR, CS) is not good, residual oil saturation is high. In non-connective abandoned channel element (CH) formation with channel, because this reverse is difficult to control by injection and production well-series, its using status is not good, even terribly not good, residual oil is enrichment. 9. The rhythm and sedimentary structure, sedimentary facies change in single sand body brings about vertical changes of formation character, growth character of inner layer interbed. These are important factor of controlling and affecting vertical water spread volume and inner layer residual oil forming and distribution in single sand body. Positive rhythm, is the principal part of fluvial sandstone inner layer sedimentary rhythm. Namely, from down to upside, rock grain granularity changes from coarse to fine, seeping ability changes from strong to feebleness. It brings about that water-driving status of inner layer upside is not good, residual oil saturation is high. Inner layer interbed has different degree affecting and controlling effect to seeping of oil and water. Its affecting degree lies on interbed thickness, extending scale, position, and jeted segment of production or injection well. The effect of interbed at upside of oil formation to oil and water seeping is less; the effect of interbed at middle of oil formation to oil and water seeping is more. 10. Indoor experiment and research indicate that wettability, permeability step, vertical permeability, position of Kmax and ratio of oil viscousity and water viscousity all have great effect on the water-driving recovery ratio. 11. Microscopic residual oil distribution is affected and controlled by formation pore network structure, pressure field distribution, and oil characteristic. 12.The residual oil forming mechanism: the over-bank sedimentary element and upper part of a positive rhythm sandstone have fine pore and throat network, permeability is low, displacement pressure of pore and throat is high. The water-driving power usually falls short of displacement pressure that brings about injection water does not spread into these pore and throat network, thereby immovable oil area, namely residual oil, is formed. At underside of channel sedimentary element and positive rhythm sandstone, porosity and permeability is relatively high, connecting degree of pore and throat is high, displacement pressure of pore and throat is low. Thereby injection water is easy to enter into pore and throat, driving oil in them. Because the pore space is irregular, the surface of pore wall is coarse and non-flat. That the oil locate on concave hole of pore wall and the dead angle of pore, and the oil attaches on surface of pore wall by surface tension, are difficult to be peeled off, becoming water-driving residual oil (remaining oil). On the other hand, Because flowing section lessens, flowing resistance increase, action of capillary fore, or seeping speed decreases at process of transfer at pass narrow throat path in the course carried by driving water. The "oil drop", "oil bead", or "oil segment" peeled off by driving water is difficult to carry and to drive out by water at less pressure difference. Thereby they are enclosed in pore to form discontinuous residual oil. 13.This results described above have been applied in nine develop blocks of Gudao and Gudong oilfield. Its applying effect is marked through local injection production adjustment, deploying replacement well, repair hole, replacement envelop, block off water and profile control etc. Relative method and technology can be applied to other oil production area of Shengli oilfield, and obtain better economic and societal effect.

准噶尔盆地中拐东北斜坡油气成藏条件研究——西部压性盆地含油气系统理论的研究与实践

This paper builds the model of oil accumulation and achieves the prediction of exploration goal. It uses multiple subject means, the ways of synthetic research and the viewpoint of analyzing genesis, with the academic guidance of sedimentology, structural geology, petroleum geology and geochemistry, the basis of strata sequence frame and structural frame, the frame of "four history" - the burying history, the structural history, the filling history and the evolving history of oil, the masterstroke of hydrocarbon's generation, migration and accumulation, the aim of revealing the genetic relation between mature source rock and oil reservoir in space and time. Some achievements and viewpoints in this study are following. 1. It is proposed that the structural evolution in this area had many periods, and the structural movement of the Xiazijie group telophase formed the structural pattern for the first time. 2. The character of strata sequence in this area is divided by the character of episodic cycle firstly. The study of dividing the facies of single well and the facies of well tie is based on the data of single well. The character of sedimentary facies is con-structed initially. 3. It is believed that Jiamuhe group is the main source rock, which can supply considerable oil and gas resources for the first time. Some criterions of source rock such as the type ,the abundance in Jiamuhe group are analysed. Using the thermal history of source rock, we drawn a conclusion that the original type of source rock in Jiamuhe group is II_1-III, and the abundance achived the level of good source rock, and this set of source rock had contributed to this area. 4. The reservoir strata in this area are assessed and analysed with the reservoir evaluation. There are multi-type reservoirs, such as volcanic lava facies, sedimentary clast facies, continental belch facies. The physical property in reservoir strata is characterized by low porosity and low permeability. The study of diagenetic stage show that the diageneses in Jiamuhe group is A-Bsubage, and the reservoir room is mainly secondary corroded hollow and cleft. 5. The synthetic research on oil system in Jiamuhe group is made for the first time. The type of petroleum system is divided , and we consider that the petroleum system of Jiamuhe group is at the reliable rank. There are two critical time in oil accumulation through studying the critical time of oil accumulation : the early generation of hydrocarbon is oil, and the later is gas. 6. The mechanism of accumulation is analysed. We consider that the accu-mulation of oil in this area has many periods, and the early generated hydrocarbon is expeled by the later , and formed the character of zonal distribution in planar. 7. A bran-new model of oil and gas is proposed. Beneficial enrichment area of oil and gas is analyzed, which can be divided into three sections: Section I can be divided into two sections: I_1 and I_2. The lower subgroup of Jiamuhe is covered by the triassic layer of I_1 section. Fault zone and near the foot wall of fault are charactered with thick phase belt. Then the cover capability in this area is relatively poor, oil can migrate into triassic layer by vertical or lateral migration , and forms I_1 Kelamayi triassic oil pool consequently. The lower subgroup of Jiamuhe is covered by the triassic layer of I_2 section ,which is charactered with thin phase belt. Then the cover capability in this area is relatively good, and forms I_1 Kelamayi triassic oil pool consequently. Section II can be divided into two sections: II_1-I_(I~2). The cover of Jiamuhe group in section II_1 is the low resistivity segment in Wuerhe group, which has thin lithology and poor porosity and permeability. Oil and gas in Jiamuhe group can be covered to form beneficial accumulation area. There are some wells in this area, such as Ke 007 well, 561 well. The thick phase belt layer of Wuerhe high resistivity segment in section II_2 has unconformable relation with Jiamuhe group. The cover ability of the high resistivity segment is poor, petroleum in Jiamuhe can migrate into Wuerhe layer vertically. This area is the beneficial area for accumulating petroleum in Wuerhe layer. there are some wells in this area, such as Ke 75 well, Ke 76 well, Ke 77 well, Ke 78 well, Ke 79 well. Section III can also be divided into two sections: III_1 and III_2. Wuerhe group in section III_1 has unconformable relation with Jiamuhe group. There is thick lithology and poor cover in Wuerhe group, but the strata sequence evolution character of upper subgroup in Jiamuhe group has determined that it has lateral and vertical cover ability. thus, this area is petroleum abundant belt of jiamuhe group, which has the trap. Section III_2 is an area controled by wedgeout of Fengcheng group, Fengcheng group in this area has quite thick lithology so that It has beneficial resevoir phase belt. It can accumulate oil in itself or accept some oil in Jiamuhe group. Jiamuhe group has some oil accumulation condition in this area. Thus, section III_2 is jiamuhe-Fengcheng multiple petroleum accumulation belt, such as Ke 80 well. 8. The goal of exploration is suggested: Depositional trap or combination trap is the important aspect in later exploration. Both types of traps are the goal of the next drilling: Fault block trap in the east of 576 well and the NO. 2 fault block trap in the north of Ke 102 well It is suggested that we should study the law of oil and gas in Jiamuhe group and enhance the study of combination in forming reservoir and trap scale. We do some lithology forecast and reservoir diatropic forecast in order to know the area of oil and gas.

叠前深度偏移速度模型的建立方法研究

Seismic exploration is the main tools of exploration for petroleum. as the society needs more petroleum and the level of exploration is going up, the exploration in the area of complex geology construction is the main task in oil industry, so the seismic prestack depth migration appeared, it has good ability for complex construction imaging. Its result depends on the velocity model strongly. So for seismic prestack depth migration has become the main research area. In this thesis the difference in seismic prestack depth migration between our country and the abroad has been analyzed in system. the tomographical method with no layer velocity model, the residual curve velocity analysical method based on velocity model and the deleting method in pre-processing have been developed. In the thesis, the tomographysical method in velocity analysis is been analyzed at first. It characterized with perfection in theory and diffculity in application. This method use the picked first arrivial, compare the difference between the picked first arrival and the calculated arrival in theory velocity model, and then anti-projected the difference along the ray path to get the new velocity model. This method only has the hypothesis of high frequency, no other hypothesis. So it is very effective and has high efficiency. But this method has default still. The picking of first arrival is difficult in the prestack data. The reasons are the ratio of signal to noise is very low and many other event cross each other in prestack data. These phenomenon appear strongly in the complex geology construction area. Based on these a new tomophysical methos in velocity analysis with no layer velocity model is been developed. The aim is to solve the picking problem. It do not need picking the event time contiunely. You can picking in random depending on the reliability. This methos not only need the pick time as the routine tomographysical mehtod, but also the slope of event. In this methos we use the high slope analysis method to improve the precision of picking. In addition we also make research on the residual curve velocity analysis and find that its application is not good and the efficiency is low. The reasons is that the hypothesis is rigid and it is a local optimizing method, it can solve seismic velocity problem in the area with laterical strong velocity variation. A new method is developed to improve the precision of velocity model building . So far the pattern of seismic prestack depth migration is the same as it aborad. Before the work of velocity building the original seismic data must been corrected on a datum plane, and then to make the prestack depth migration work. As we know the successful example is in Mexico bay. It characterized with the simple surface layer construction, the pre-precessing is very simple and its precision is very high. But in our country the main seismic work is in land, the surface layer is very complex, in some area the error of pre-precessing is big, it affect the velocity building. So based on this a new method is developed to delete the per-precessing error and improve the precision of velocity model building. Our main work is, (1) developing a effective tomographical velocity building method with no layer velocity model. (2) a new high resolution slope analysis method is developed. (3) developing a global optimized residual curve velocity buliding method based on velocity model. (4) a effective method of deleting the pre-precessing error is developing. All the method as listed above has been ceritified by the theorical calculation and the actual seismic data.

公众个人捐赠动机及其影响因素

Along with Chinese general national power upgrades constantly, the gaps between the rich and the poor in different areas and groups increased by contraries. Charity career in China attracts more and more attention. In western society, there is consanguineous correlativity between the development of charity career and charity marketing, and donation motivation is one of the most important factors. It’s mainly focus on two issues, one is the process of donation behavior and the other one is the drive of donation behavior. There are great differences between domestic studies on donation motivation and the current correlative theory due to different cultures, religions, regions and so on. In this article, western theory of donation motivation has been summarized and meanwhile the unique domestic donation motivation has been analyzed. The article includes two studies. Firstly, investigated domestic individual donation motivation as well as primary donation behavior, secondly studied the structure of donation motivation by questionnaire. Results show that, firstly, there are four factors in Chinese individual donation motivation which were cost-income balance, passive donation, to do good and accumulate merit, public morality and habit-share. Organization disadvantage and ability limit are the two factors in unwilling donation motivation. Secondly, in this survey, there are no significant differences between cost-income balance and demographic variables. Passive donation motivation shows significant differences only on gender and occupation. To do good and accumulate merit shows significant difference only on occupation. To do good and accumulate merit and habit-share also show significant differences on age. Passive donation is one of special factors in China. Thirdly, donors are prefer to help children who unable to go to school and people who hit by a natural calamity than to help agriculture labourer and laid-off worker. At last, donors concern more about the information feedback such as how was their donation has been used. If the charity organization can not meet the donors’demands in this aspect, it will be surely result in unwilling donation.

职业倦怠与自我和谐、人际信任的关系研究：中学校长与一般教师的对比

Job Burnout has been a focus of the Occupational Stress Research. As a typical,helping occupation, teacher has attracted widely attention and researches in the areas of pedagogy and psychology. The special subgroup of teacher, headmasters who are the elites of the Basic Education, is ignored. The research about principals’ Job Burnout is nearly blank after analyzing related documents and information. With the development of the society, people pay more and more attention to the education and put more demands on the headmasters, especially middle-school principals. They are required not only to be good educators, who are equipped with all the inner qualities as a teacher, but also good managers. So the main purpose of this research was to compare the principal group with ordinary teacher group, and reveal underling factors, such as background variables and psychological protection variables. A representative sample of Wenzhou middle school principals sized 192 and a sample of middle school teacher sized 302 were sampled from various schools. The educational version of burnout inventory, self consistency scale, and interpersonal trust scale were administrated to the two samples, together with some demographic variables of interest. The applicability and equivalence of the three instruments used in this study were checked. Based on well-established reliability and cross-sample congruence of measures, the difference between principals and teachers was test. Then the contributing factors were analysis gradually. The five background variables were examined one by one in the two samples separately. A multiple covariance analysis was conducted to test whether there remained any difference between these two samples on the variables of interest. Regression analysis was used to further control the effect of self harmony and interpersonal trust to test the difference between two samples. Mediating analysis was conducted to build the relationship among the three constructs. The main results of the research were stated as following: 1. The internal consistency coefficients of all the scales were good, and no difference exited between the two groups. The measurement equivalence of three instruments was established well. The measures could be applied to and comparing the two samples. 2. The self-harmony, and interpersonal trust of principals were better than the ordinary middle-school teachers. Job Burnout of principals was significant lower than teachers. 3. Demographic variables like the gender, age groups, income levels, disricts, and the type of school, were important influencing factors. The difference patterns of the variables on these five variables in two samples had similarity and distinction. 4. After controlling the background variables, there remained significant difference between principals and teachers on the variables of interest. 5. Job Burnout negatively correlated with self-harmony and interpersonal trust. That is to say，the lower the degree of self-harmony and interpersonal are, the serious of the Job Burnout is, The correlation between the self-harmony and the interpersonal trust was positive. 6. After statistically controlling the background variables and psychological variables, there still exited significant difference between two groups of this study. Also, self harmony and interpersonal trust were significant protection predictors to different aspect of job burnout. 7. Mediating analysis was conducted to the residual score of the three constructs after controlling the five variables and group membership. Self harmony partially mediated the relationship between interpersonal trust and job burnout. That is, interpersonal trust had indirect effect to burnout mediated by self harmony, also had direct effect to burnout.

不同智力水平儿童的自我调控特点

Self-regulation has recently become an important topic in cognitive and developmental domain. According to previous theories and experimental studies, it is shown that self-regulation consist of both a personality (or social) aspect and a behavioral cognitive aspect of psychology. Self-regulation can be divided into self-regulation personality and self-regulation ability. In the present study researches have been carried out from two perspectives: child development and individual differences. We are eager to explore the characteristics of self-regulation in terms of human cognitive development. In the present study, we chose two groups of early adolescences one with high intelligence and the other with normal intelligence. In Study One Questionnaires were used to compare whether the highly intelligent group had had better self-regulation personality than the normal group. In Study Two experimental psychology tasks were used to compare whether highly intelligent children had had better self-regulation cognitive abilities than their normal peers. Finally, in Study Three we combined the results of Study One and Study Two to further explore the neural mechanisms for highly intelligent children with respect to their good self-regulation abilities. Some main results and conclusions are as follows: (1) Questionnaire results showed that highly intelligent children had better self-regulation personalities, and they got higher scores on the personalities related to self-regulation such as, self-reliance, stability, rule-consciousness. They also got higher scores on self-consciousness which meant that they could know their own self better than the normal children. (2) Among the three levels of cognitive difficulties in self-regulation abilities, the highly intelligent children had faster reaction speed than normal children in the primary self-regulation tasks. In the intermediate self-regulation tasks, highly intelligent children’s inhibition processing and executive processing were both better than their normal peers. In the advanced self-regulation tasks, highly intelligent children again had faster reaction speed and more reaction accuracy than their normal peers when facing with conflict and inconsistency experimental conditions,. Regression model’s results showed that primary and advanced self-regulation abilites had larger predictive power than intermediate self-regualation ability. (3) Our neural experiments showed that highly intelligent children had more efficient neural automatic processing ability than normal children. They also had better, faster and larger neural reaction to novel stimuli under pre-attentional condition which made good and firm neural basis for self-regualation. Highly intelligent children had more mature frontal lobe and pariental functions for inhibition processing and executive processing. P3 component in ERP was closely related to executive processing which mainly activated pariental function. There were two time-periods for inhibition processing—first it was the pariental function and later it was the coordination function of frontal and pariental lobes. While conflict control task had pariental N2 and frontal-pariental P3 neural sources, highly intelligent children had much smaller N2 and shorter P3 latency than normal children. Inconsistency conditions induced larger N2 than conditions without inconsistency, and conditions without inconsistency (or Conflict) induced higher P3 amplitudes than with Inconsistency (or Conflict) conditions. In conclusion, the healthy development of self-regulation was very important for children’s personality and cognition maturity, and self-regulation had its own specific characteristics in ways of presentation and ways of development. Better understanding of self-regulation can further help the exploration of the nature of human intelligence and consciousness.

Lanthanide complex/polymer composite optical resin with intense narrow band emission, high transparency and good mechanical performance

Novel composite resins possessing good luminescent properties have been synthesized through a free radical copolymerization of styrene, alpha-methylacrylic acid and the binary or ternary complexes of lanthanide ions (Eu3+ and Tb3+). These polymer-based composite resins not only possess good transparency and mechanical performance but also exhibit an intense narrow band emission of lanthanide complexes under UV excitation. We characterized the molecular structure, physical and mechanical performance, and luminescent properties of the composite resins. Spectra investigations indicate that alpha-methyl-acrylic acid act as both solubilizer and ligand. Photoluminescence measurements indicate that the lanthanide complexes show superior emission lines and higher intensities in the resin matrix than in the corresponding pure complex powders, which can be attributed to the restriction of molecular motion of complexes by the polymer chain networks and the exclusion of water molecules from the complex. We also found that the luminescence intensity decreased with increasing content of alpha-methylacrylic acid in the copolymer system. The lifetime of the lanthanide complexes also lengthened when they were incorporated in the polymer matrix. In addition, we found that the relationships between emission intensity and Tb (Eu) content exhibit some extent of concentration quenching.