Optimal design of a 7 T highly homogeneous superconducting magnet for a Penning trap

A Penning trap system called Lanzhou Penning Trap (LPT) is now being developed for precise mass measurements at the Institute of Modern Physics (IMP). One of the key components is a 7 T actively shielded superconducting magnet with a clear warm bore of 156 mm. The required field homogeneity is 3 x 10(-7) over two 1 cubic centimeter volumes lying 220 mm apart along the magnet axis. We introduce a two-step method which combines linear programming and a nonlinear optimization algorithm for designing the multi-section superconducting magnet. This method is fast and flexible for handling arbitrary shaped homogeneous volumes and coils. With the help of this method an optimal design for the LPT superconducting magnet has been obtained.

基于D稳定域和ITAE准则的主动队列管理算法

主动队列管理（active queue management，简称AQM）是网络拥塞控制的研究热点之一，其中的关键问题是如何设计反馈控制策略．提出一种新的基于D稳定域和时间乘以误差绝对值乘积积分（integral of time-weighted absolute error,简称ITAE）性能准则的比例-积分-微分（proportional-integral-differential，简称PID）优化设计方法（简称DITAE-PID），并用于AQM控制器的设计，控制闭环系统的理想动态性能．首先在复平面上设定一组理想的D稳定域，然后以ITAE为目标函数，通过数值优化算法求出控制器的参数，使得闭环系统的所有特征根都在D稳定域内，以降低排队延时，提高有效吞吐量．对比仿真实验结果表明孩算法能够预先探测和控制拥塞，有较好的鲁棒性，链路利用率更高，丢包率更小，平均队列长度更趋于期望值，同时，趋于期望队列长度的时间更短，其综合性能明显优于典型的随机早期探测（random early detection，简称RED）和比例-积分（proportional-integral，简称PI）算法．

Design of adjustable superresolving filters based on birefringent crystals

A two-mode adjustable superresolving filter based on a birefringent filter is proposed. This kind of filter has superresolution in two modes of adjustment. One is rotation of the binary pupil filter on the optical axis of the system and the other is the tilt of the filter away from the pupil plane on axis parallel or perpendicular to the optical axis of the crystal. The filters act as complex amplitude filters in the former mode, and as pure phase filters in the latter. By analyzing two superresolving parameters, we obtain the optimal design parameters that ensure a large field of view, a large superresolving range, and a high setting accuracy. This kind of filter can provide more flexibility in practical applications. (c) 2006 Optical Society of America.

Characteristics of high reflection mirror with an SiO2 top layer for multilayer dielectric grating

The high reflection (HR) mirror composed of dielectric stacks with excellent spectrum characteristics and high damage resistant ability is critical for fabricating multilayer dielectric (MLD) grating for pulse compressor. The selection of the SiO2 material as the top layer of the HR mirror for grating fabrication is beneficial for improving the laser-induced damage threshold of MLD grating as well as minimizing the standing-wave effect in the photoresist during the exposure process. Based on an (HLL) H-9 design comprising quarter-waves of HfO2 ( H) and half-waves of SiO2 ( L), we obtain an optimal design of the HR mirror for MLD grating, the SiO2 top layer of which is optimized with a merit function including both the diffraction efficiency of the MLD grating and the electric field enhancement in the grating. Dependence of the performance of the MLD grating on the fabrication error of the dielectric mirror is analysed in detail. The HR mirror is also fabricated by E-beam evaporation, which shows good spectral characteristics at the exposure wavelength of 413 nm and at the operation wavelength of 1053 nm and an average damage threshold of 10 J cm(-2) for a 12 ns pulse.

氮、磷、钾对膜荚黄芪生长发育及有效成分的影响

目的:研究氮、磷、钾及其配比对膜荚黄芪生长发育及有效成分的影响。方法:通过田间试验,采用氮、磷、钾3因素2次D-饱和最优设计,研究氮、磷、钾及其配比对膜荚黄芪生长及有效成分的影响。结果:施肥促进了膜荚黄芪幼苗的生长,从而为生育后期膜荚黄芪根生长、产量形成及有效成分的累积提供充足的营养基础。氮、磷、钾各元素及其配比明显促进了茎叶及根干物质积累,氮、磷、钾对膜荚黄芪干物质累积总量的影响程度依次为氮>钾>磷;对膜荚黄芪茎叶干物质累积量的影响程度依次为氮>磷>钾;对根干物质累积量的影响程度依次为氮>钾>磷。施肥明显提高了膜荚黄芪根产量,氮、磷、钾对根产量影响程度依次为氮>钾>磷。氮、磷、钾各元素及其配比使黄芪多糖、黄芪甲苷含量明显增加,对总黄酮含量影响不明显。氮、磷、钾对黄芪多糖含量影响程度依次为钾>磷>氮;对黄芪甲苷含量的影响程度依次为氮>钾>磷。结论:氮、钾对膜荚黄芪生长发育,产量形成及多糖,黄芪甲苷含量有重要的影响。根类中药材黄芪的栽培过程中应该注重氮、钾肥的施用,并注意氮、磷、钾的配合施用。

填土边坡水文作用机理与破坏过程研究—以深圳羊宝地填土滑坡为例

A full understanding of failure mechanism, critical hydrological condition, and process of mobilization and deposition of a landslide is essential for optimal design of stabilization measure and forecasting of landslide hazard. This requires a quantitative study of hydrological response of a slope to rainfall through field monitoring, laboratory test and numerical modelling. At 13:40 on September 18, 2002, a fill slope failed following a period of prolonged rain in Shenzhen, resulting in 5 fatalities and 31 injuries. The failed mass with a volume about 2.5×104m3 traveled about 140m on level ground. Field monitoring, laboratory test, theoretical analysis and numerical modelling were carried out to undestand the hydrological response and failure mechanism of this fill slope. This thesis mainly focuses on the following aspects: (1) The hydrological responses and failure processes of slopes under rainfall infiltration were reviewed. Firstly, the factors influencing on the hydrological responses of slopes were analysed. Secondly, the change of stress state of slope soil and modelling methods of slope failure under rainfall infiltration were reviewed. (2) The characteristics of the Yangbaodi landslide and associated rainfall triggering the failure were presented. The failure was characterized by shallow flowslide, due to an increase of ground water table caused by rainfall infiltration. (3) A fully automated instrumentation was carried out to monitor rainfall, and saturated – unsaturated hydrological response of the fill slope, using a raingauge, piezometers, tensiometers and moisture probes. A conceptual hydrogeological model was presented based on field monitoring and borehole data. Analysis of monitoring data showed that the high pore water pressure in fill slope was caused by upward flow of semiconfined groundwater in the moderately decomposed granite. (4) Laboratory and in-situ testing was performed to study the physical and mechanical properties of fills. Isotropically consolidated undrained compression tests and anisotropically consolidated constant shear stress tests were carried out to understand the failure mechanism of the fill slope. It is indicated that loosely compacted soil is of strain-softening behaviour under undrained conditions, accompanied with a rapid increase in excess pore water pressure. In anisotropically consolidated constant shear stress tests, a very small axial strain was required to induce the failure and the excess pore water pressure increased quickly at failure. This indicated that static liquefaction caused by rise in groundwater table due to rainfall infiltration occurred. (5) The hydraulic conductivity of the highly and moderately decomposed granite was estimated using monitering data of pore water pressure. A saturated – unsaturated flow was modeled to study the hydrological response of the fill slope using rainfall records. It was observed that the lagged failure was due to the geological conditions and the discrepancy of hydraulic conductivity of slope soils. The hydraulic conductivity of moderately decomposed granite is relatively higher than the other materials, resulting in a semiconfied groundwater flow in the moderately decomposed granite, and subsequent upward flow into the upper fill layer. When the ground water table in the fill layer was increased to the critical state, the fill slope failed. (6) Numerical exercises were conducted to replay the failure process of the fill slope, based on field monitoring, laboratory and in-situ testing. It was found that the fill slope was mobilized by a rapid transfer of the concentrated shear stress. The movement of failure mass was characterized by viscosity fluid with a gradual increase in velocity. The failure process, including mobilization and subsequent movement and deposition, was studied using numerical methods.

平行平板角位移干涉测量仪的优化设计

提出一种可提高平行平板角位移干涉测量仪测量精度的优化设计方法。对角位移干涉测量系统进行了误差分析，讨论了影响角位移测量精度的主要因素。分析了在干涉仪光路中入射到平行平板上的初始入射角度、平行平板的折射率以及厚度等参数的选取对角位移测量精度的影响。结果表明，优化选取最佳的初始入射角度以及元件参数，并在干涉光路中附加引入一平面反射镜形成光程差放大系统，可实现的角位移测量精度达10-8 rad数量级。

有限尺寸光栅压缩器的优化设计

分析了超短超强激光系统中有限尺寸光栅压缩器设计的关键物理参数及约束条件,得到了压缩器优化的三项基本变量。给出了一种输出能量最大化的压缩器优化方法,进而确定了有限尺寸光栅压缩器的最大工作能力。针对传统的圆光束方案提出了改进的椭圆光束方案,增大了聚焦能量,减小了焦斑尺寸,提高了峰值聚焦功率密度。通过数值模拟对500 mm曝光口径介质膜光栅在圆光束和椭圆光束两种方案下的最大输出能力进行分析比较,指出单块光栅在椭圆光束方案下可以实现500 fs,500 J,1 PW的脉冲输出。

Optical fiber long-period grating with solgel coating for gas sensor

The novel long-period fiber grating (LPFG) film sensor is composed of the long-period grating coated with solgel-derived sensitive films. The characteristics of the transmissivity of the LPFG film sensor are studied. By analyzing the relation among the sensitivity S-n, the thin film optical parameters, and the fiber grating parameters, the optimal design parameters of the LPFG film sensor are obtained. Data simulation shows that the resolution of the refractive index of this LPFG film sensor is predicted to be 10(-8). Experimentally, a LPFG film sensor for detection Of C2H5OH was fabricated, and a preliminary gas-sensing test was performed. (c) 2006 Optical Society of America.

复合生态系统油画结构与全球变化研究

在分析毛乌素沙地自然、社会经济、人文等条件与现状的基础上，诊断生态经济复合系统运行的限制因素及有利条件。运用线性规划的理论与方法进行系统的优化设计。为保证生态经济复合系统的持续发展，降水量以80%保证率的280mm计算为宜，则径流园林区的种植覆盖度可达到65%;高效农牧区的种植覆盖度可达到75%，最大不超过80%。同时表明在毛乌素沙地高效生态经济复合系统持续发展的限制因子主要是水分。 根据植物的生理生态学特点及诸气候要素建立了农业净第一性生产力模型，经我国27个省区农业生产力资料的验证表明，该模型较自然植被的净第一性生产力模型Chikugo模型和综合模型能更好地反应农业净第一性生产力。 根据自然植被净第一性生产力综合模型、农业净第一性生产力模型计算了我国自然植被及农作物的净第一性生产力，对我国自然植被与农作物对全球变化敏感性的研究表明：在所有可能的气候条件下，我国陆地生态系统的生产力表现出由东南向西北递减的趋势及明显的条带状分布，在西北地区形成明显的低值区。 根据叶面积指数、标准化差植被指数建立了中国森林植被净第一性生产力模型，经我国13组森林植被生产力数据的验证表明，该模型的预测结果与实测相符较好。通过与Chikugo模型和综合模型预测结果的比较，该模型在总体上优于Chikugo模型和综合模型。表明基于NDVI的净第一性生产力模型对我国森林植被有良好的适应性，可用于快速监测与预测我国森林生产力的动态变化。

Delay of the excited state lasing of 1310 nm InAs/GaAs quantum dot lasers by facet coating

In this letter, we present a facet coating design to delay the excited state (ES) lasing for 1310 nm InAs/GaAs quantum dot lasers. The key point of our design is to ensure that the mirror loss of ES is larger than that of the ground state by decreasing the reflectivity of the ES. In the facet coating design, the central wavelength is at 1480 nm, and the high- and low-index materials are Ta2O5 and SiO2, respectively. Compared with the traditional Si/SiO2 facet coating with a central wavelength of 1310 nm, we have found that with the optimal design the turning temperature of the ES lasing has been delayed from 90 to 100 degrees C for the laser diodes with cavity length of 1.2 mm. Furthermore, the characteristic temperature (T-0) of the laser diodes is also improved.

模糊免疫非线性PID控制的优化设计

在深入分析生物免疫系统中T细胞对B细胞辅助调节作用的基础上,提出了免疫反馈原理。针对非最小相位极点系统控制的难点,借鉴免疫反馈原理,结合积分控制的规律,提出了一种模糊免疫非线性PID控制方法。由于该方法中的参数确定比较复杂,利用免疫进化算法进行参数优化设计,实现了控制参数的合理设计。仿真结果表明,该方法在非最小相位极点系统控制中可行且有效,优于PID控制方法,具有更好的响应特性和抗干扰性能。

并联结构六维力传感器性能分析与优化设计

基于螺旋理论和空间模型理论绘制了Stewart平台型六维力传感器的性能图谱,总结了结构参数对传感器各性能指标的影响规律;在此基础上对大型Stewart平台六维力传感器的结构进行了非线性单目标、多目标优化设计,为具有普通球形铰链大型Stewart平台六维力传感器的设计和优化提供了依据。

一种低功耗微弱信号放大电路的优化设计与研究

针对远距离声源发射的水声信号微弱、水声接收设备电源能量有限的特点,提出一种功耗小、对无源元件误差灵敏度低、高增益放大的微弱水声信号通用放大电路。系统采用场效应管共源单调谐放大器为前置放大级,由四级级联低功耗运放构成带通滤波放大电路,省去传统的R、C低通网络,实现了对微弱水声信号的高增益放大和海洋背景噪声的归一化处理。通过计算电路网络传递函数极点证明了电路系统的稳定性。海上使用表明系统具有精度高、适应性强、电路稳定性好、功耗小等优点。

深水滑翔机器人耐压壳体结构优化设计

针对深水滑翔机器人耐压壳体在深水中压缩变形和海水密度随水深增大而变化等因素造成驱动浮力变化问题,利用压缩变形和密度变化对驱动浮力影响的互补特性,归纳了载体耐压壳体结构优化设计方法。保证耐压壳体抗压条件和质量最小前提下采用结构优化设计方法,降低耐压壳体压缩变形和海水密度变化对驱动浮力的影响,提高系统能源的利用率。