60 resultados para BORON 10
em Chinese Academy of Sciences Institutional Repositories Grid Portal
Resumo:
电子邮箱nataliya.deyneka@uni-ulm.de
Resumo:
Cubic boron nitride (c-BN) films were prepared by ion beam assisted deposition (IBAD) technique, and the stresses were primary estimated by measuring the frequency shifts in the infrared-absorption peaks of c-BN samples. To test the possible effects of other factors, dependencies of the c-BN transversal optical mode position on film thickness and c-BN content were investigated. Several methods for reducing the stress of c-BN films including annealing, high temperature deposition, two-stage process, and the addition of a small amount of Si were studied, in which the c-BN films with similar thickness and cubic phase content were used to evaluate the effects of the various stress relief methods. It was shown that all the methods can reduce the stress in c-BN films to various extents. Especially, the incorporation of a small amount of Si (2.3 at.%) can result in a remarkable stress relief from 8.4 to similar to 3.6 GPa whereas the c-BN content is nearly unaffected, although a slight degradation of the c-BN crystallinity is observed. The stress can be further reduced down below I GPa by combination of the addition of Si with the two-stage deposition process. (c) 2008 Elsevier B.V. All rights reserved.
Resumo:
To investigate the effect of radiation damage on the stability and the compressive stress of cubic boron nitride (c-BN) thin films, c-BN films with various crystalline qualities prepared by dual beam ion assisted deposition were irradiated at room temperature with 300 keV Ar+ ions over a large fluence range up to 2 x 10(16) cm(-2). Fourier transform infrared spectroscopy (FTIR) data were taken before and after each irradiation step. The results show that the c-BN films with high crystallinity are significantly more resistant against medium-energy bombardment than those of lower crystalline quality. However, even for pure c-BN films without any sp(2)-bonded BN, there is a mechanism present, which causes the transformation from pure c-BN to h-BN or to an amorphous BN phase. Additional high resolution transmission electron microscopy (HRTEM) results support the conclusion from the FTIR data. For c-BN films with thickness smaller than the projected range of the bombarding Ar ions, complete stress relaxation was found for ion fluences approaching 4 x 10(15) cm(-2). This relaxation is accompanied, however, by a significant increase of the width of c-BN FTIR TO-line. This observation points to a build-up of disorder and/or a decreasing average grain size due to the bombardment. (c) 2005 Elsevier B.V. All rights reserved.
Resumo:
Boron removal is a critical issue in the production of drinking water and of ultra-pure water in the electronics industry. Boron rejection in a RO process is typically in the range of 40-60%. The objective of this study was to distinguish the factor contributing to enhanced boron rejection in reclamation of a spent rinse stream from a plating operation. The effects of different known components used in the feed on boron removal were investigated in the laboratory. The results indicated that glycolic acid and antifoulants could not individually enhance boron rejection in a RO process. A high boron rejection of 95% was achieved as the concentration of iron in the feed was 10 times higher than that of boron, which might be due to formation of a complex between iron oxide and boron. The finding was confirmed in a pilot study.
Resumo:
The structural evolution and property changes in Nd60Al10Fe20Co10 bulk metallic glass (BMG) upon crystallization are investigated by the ultrasonic method, x-ray diffraction, density measurement, and differential scanning calorimetry. The elastic constants and Debye temperature of the BMG are obtained as a function of annealing temperature. Anomalous changes in ultrasonic velocities, elastic constants, and density are observed between 600–750 K, corresponding to the formation of metastable phases as an intermediate product in the crystallization process. The changes in acoustic velocities, elastic constants, density, and Debye temperature of the BMG relative to its fully crystallized state are much smaller, compared with those of other known BMGs, the differences being attributed to the microstructural feature of the BMG.
Resumo:
利用材料测试系统(MTS)、X-Ray 衍射(XRD)和扫描电镜(SEM)等手段研究了Nd 基大块金属玻璃的变形行为和断裂特征。Nd 基大块金属玻璃样品在室温下是脆性断裂,大约在500 K 时变形模式从非均匀变形转变为均匀变形,在523 K 以上表现出显著的塑性变形。在5×10-4 m/s 的应变速率下,这种Nd 基大块金属玻璃材料在523 K~600 K 之间出现明显的屈服应力下降现象,随后进入1 种稳定的粘性流动状态,而且这种屈服下降现象与温度和应变速率有关。这种在过冷液相区的变形行为与其他大块金属玻璃变形特征相似。合金的这种塑性变形行为表明了其存在稳定的过冷液相区,同时对其变形行为的研究有助于进一步了解Nd 基大块金属玻璃的反常热稳定性。
Resumo:
Microcantilever-based biosensors have been found increasing applications in physical, chemical, and biological fields in recent years. When biosensors are used in those fields, surface stress and mass variations due to bio-molecular binding can cause the microcantilever deform or the shift of frequency. These simple biosensors allow biologists to study surface biochemistry on a micro or nano scale and offer new opportunities in developing microscopic biomedical analysis with unique characteristics. To compare and illustrate the influence of the surface stress on the frequency and avoid unnecessary and complicated numerical solution of the resonance frequency, some dimensionless numbers are derived in this paper by making governing equations dimensionless. Meanwhile, in order to analyze the influence of the general surface stress on the frequency, a new model is put forward, and the frequency of the microcantilever is calculated by using the subspace iteration method and the Rayleigh method. The sensitivity of microcantilever is also discussed. (19 refs.)
Resumo:
Bulk metallic glasses of Nd65Al10Fe25-xCox (x=0,5,10) have been prepared in the form of 3 mm diam rods. Results of differential scanning calrimetry, dynamic mechanical thermal analysis (DMTA), and x-ray diffraction are presented for these alloys. It is shown that the glass transition and crystallization have been observed by DMTA. The reduced glass transition temperature of these glasses, defined as the ratio between the glass transition temperature T-g and the melting temperature T-l is in the range from 0.55 to 0.62. All these glasses have a large supercooled liquid region (SLR), ranging from 80 to 130 K. The high value of reduced glass transition temperature and wide SLR agree with their good glass formation ability.
Resumo:
该文回顾了中国振动工程学会随机振动专业委员会成立后的10年间我国学者在随机振动领域所进行的理论、应用技术研究方面取得的一些重要进展。着重介绍了随机非线性响应时域积分方法与空间有限元结合的随机动力有限元方法的发展;对随机振动与其他相关学科的交叉渗透进一步发展的前景也作了展望。
Resumo:
JP-10 (exo-tetrahydrodicyclopentadiene, C10H16) ignition delay times were measured in a preheated shock tube. The vapor pressures of the JP-10 were measured directly by using a high-precision vacuum gauge, to remedy the difficulty in determining the gaseous concentrations of heavy hydrocarbon fuel arising from the adsorption on the wall in shock tube experiments. The whole variation of pressure and emission of the OH or CH radicals were observed in the ignition process by a pressure transducer and a photomultiplier with a monochromator. The emission of the OH or CH radicals was used to identify the time to ignition. Experiments were performed over the pressure range of 151-556 kPa, temperature range of 1000-2100 K, fuel concentrations of 0.1%-0.55% mole fraction, and stoichiometric ratios of 0.25, 0.5, 1.0 and 2.0. The experimental results show that for the lower and higher temperature ranges, there are different dependency relationships of the ignition time on the temperature and the concentrations of JP-10 and oxygen.
Resumo:
在中科院力学所JF-4B高超声速脉冲风洞中,用模型自由飞方法对10~。尖锥开展动态实验测量,并用参数微分法辨识得到了该模型的俯仰阻尼导数。实验结果表明,脉冲风洞中模型自由飞方法得到的10~。尖锥标模高超声速动态气动特性测量值与国外可比数据一致,重复测量精度与弹道靶试验相当。
Resumo:
<正> 国际尖端材料技术协会(SAMPE:Society for the Advancement of Material and Process Engineering)于1992年10月20—22月在加拿大多伦多市召开了两个国际学术会议:第24届国际SAMPE技术会议(24th Int.SAMPE Techn。Coaf。)和第3届国际金属与金属加工会议(3rd Int.SAMPE Metals and Metals Processin Conf.)。两个会议同时举行,全体会议(Plenary Session)在一个会场举行。前者的主题是“先进材料迎接经济的挑战”;后者的主题是“合成与加工的新进展”.尽管此二会议是在西方发达国家经济很不景
Resumo:
本文介绍一种0~10mm、分辨率1μm数字光栅测微仪,它是一种具有任意零点、高精度的测长系统,由光栅位移传感器和数显仪两部分组成。介绍了其工作原理、主要技术指标和应用。