High transmission of slow light in the photonic crystal waveguide bends

We present the research on the transmission characteristic of slow-light-mode in the photonic crystal line-defect waveguide bends on SOL After optimizing the structure parameters in the vicinity of the bends, the normalized transmission efficiency of slow-light-mode through the photonic crystal 60 degree and 120 degree waveguide bends are as high as 80% and 60% respectively, which are 10 times higher than that in the undeformed case. To slow down light further, we design novel coupled cavity waveguide bend structures with high quality-factor. High normalized transmission efficiency of 75% and low group velocity of c/170 ( c is the light velocity in vacuum) are realized. These results are beneficial to enhance the slow light effect of photonic crystal structures and improve the miniaturization and integration of photonic crystal slow light devices.

Structural optimizations of SOI-based single-mode rib waveguide bends

Effects of structure parameters on bend loss of rib silicon-on-insulator (Sol) bend waveguides have been analyzed by means of effective index method (EIM) and 2D bend loss formula. The simulation results indicate that the bend loss decreases with the increase of bend radius and waveguide width, as well as with the decrease of the step factor of the rib waveguide. Moreover, the optional structure parameters have been found when bend waveguides are single-mode.

爆轰波在弯管内传播过程数值分析

应用基元反应模型和频散可控耗散格式(DCD)对氢氧爆轰波在弯管内的传播过程进行了数值模拟.计算中氢氧混合物化学反应采用了8种组分20个反应方程式.在处理化学反应引起的刚性问题时采用了时间算子分裂的方法.计算结果表明,在弯管小曲率半径壁面附近,由于膨胀稀疏作用,爆轰波强度减弱,在局部出现前导激波与放热反应区的解藕以及二次起爆现象;在弯管大曲率半径壁面上爆轰波在马赫反射和正规反射之间相互转变,使爆轰波加强.弯管内的爆轰现象与弯管曲率半径有关.

Two-phase flow patterns in a 90 degrees bend at microgravity

Bends are widely used in pipelines carrying single- and two-phase fluids in both ground and space applications. In particular, they play more important role in space applications due to the extreme spatial constraints. In the present study, a set of experimental data of two-phase flow patterns and their transitions in a 90degrees bend with inner diameter of 12.7 mm. and curvature radius of 76.5 mm at microgravity conditions are reported. Gas and liquid superficial velocities are found to range from (1.0 similar to 23.6) m/s for gas and (0.09 similar to 0.5) m/s for liquid, respectively. Three major flow patterns, namely slug, slug-annular transitional, and annular flows, are observed in this study. Focusing on the differences between flow patterns in bends and their counterparts in straight pipes, detailed analyses of their characteristics are made. The transitions between adjoining flow patterns are found to be more or less the same as those in straight pipes, and can be predicted using Weber number models satisfactorily. The reasons for such agreement are carefully examined.

Dynamics of RNA with A6 bulge loop

In order to understand the behavior of RNAs with large bulges In solution, molecular dynamics was performed on the RNA molecule in water with A6 bulge. The result of simulation showed that nonstacked conformation Is the main conformation in large bulges, and the backbone of large bulge is of great conformational flexibility, but bulges-induced bends are relatively rigid. The fluctuation in bulge has little influence on the bend angle of RNAs.

Design and fabrication of compact nonblocking 4X4 optical matrix switch on silicon-on-insulator by anisotropic chemical etching

A folding nonblocking 4 X 4 optical matrix switch in simplified-tree architecture was designed and fabricated on a silicon-on-insulator wafer. To compress chip size, switch elements (SEs) were connected by total internal reflection mirrors instead of conventional S-bends. For obtaining smooth interfaces, potassium hydroxide (KOH) anisotropic chemical etching of silicon was employed. The device has a compact size of 20 X 3.2 mm(2) and a fast response of 8 +/- 1 mu s. Power consumption of 2 x 2 SE and excess loss per mirror were 145 mW and -1.1 dB, respectively. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

Integrated folding 4x4 optical matrix switch with total internal reflection mirrors on SOI by anisotropic chemical etching

A folding rearrangeable nonblocking 4 x 4 optical matrix switch was designed and fabricated on silicon-on-insulator wafer. To compress chip size, switch elements (SEs) were interconnected by total internal reflection (TIR) mirrors instead of conventional S-bends. For obtaining smooth interfaces, potassium hydroxide anisotropic chemical etching of silicon was utilized to make the matrix switch for the first time. The device has a compact size of 20 x 1.6 mm(2) and a fast response of 7.5 mu s. The power consumption of each 2 x 2 SE and the average excess loss per mirror were 145 mW and -1.1 dB, respectively. Low path dependence of +/- 0.7 dB in total excess loss was obtained because of the symmetry of propagation paths in this novel matrix switch.

Light-propagation characteristics of photonic crystal waveguide based on SOI materials at different polarized states

Straight single-line defect optical waveguides in photonic crystal slabs are designed by the plane wave expansion method and fabricated into silicon-on-insulator (SOI) wafer by 248-nm deep UV lithography. We present an efficient way to measure the light transmission spectrum of the photonic crystal waveguide (PhC WG) at given polarization states. By employing the Mueller/Stokes method, we measure and analyse the light propagation properties of the PhC WG at different polarized states. It is shown that experimental results are in agreement with the simulation results of the three-dimensional finite-difference-time-domain method.

Transport phenomena in radial flow MOCVD reactor with three concentric vertical inlets

Transport phenomena in radial flow metalorganic chemical vapor deposition (MOCVD) reactor with three concentric vertical inlets are studied by two-dimensional numerical modeling. By varying the parameters such as gas pressure, flow rates combination of multi-inlets, geometric shapes and sizes of reactor and flow distributor, temperatures of susceptor and ceiling, and susceptor rotation, the corresponding velocity, temperature, and concentration fields inside the reactor are obtained; the onset and change of flow recirculation cells under influences of those parameters are determined. It is found that recirculation cells, originated from flow separation near the bend of reactor inlets, are affected mainly by the reactor height and shape, the operating pressure, the flow rates combination of multi-inlets, and the mean temperature between susceptor and ceiling. By increasing the flow rate of mid-inlet and the mean temperature, decreasing the pressure, maintaining the reactor height below certain criteria, and trimming the bends of reactor wall and flow distributor to streamlined shape, the recirculation cells can be minimized so that smooth and rectilinear flow prevails in the susceptor region, which corresponds to smooth and rectilinear isotherms and larger reactant concentration near the susceptor. For the optimized reactor shape, the reactor size can be enlarged to diameter D = 40 cm and height H = 2 cm without flow recirculation. The susceptor rotation over a few hundred rpm around the reactor central axis will induce the recirculation cell near the exit and deflect the streamlines near the susceptor, which is not the case for vertical reactors. (c) 2006 Elsevier B.V. All rights reserved.

Realization of SOI submicrometer optical waveguide components - art. no. 68380L

Submicrometer channel and rib waveguides based on SOI (Silicon-On-Insulator) have been designed and fabricated with electron-beam lithography and inductively coupled plasma dry etching. Propagation loss of 8.39dB/mm was measured using the cut-back method. Based on these so-called nanowire waveguides, we have also demonstrated some functional components with small dimensions, including sharp 90 degrees bends with radius of a few micrometers, T-branches, directional couplers and multimode interferometer couplers.

SOI submicron rib waveguides: Design, Fabrication and Characterization

We present detailed design, fabrication, and characterization issues of submicron rib waveguides based on silicon-on-insulator. The waveguides fabricated by EBL and ICP processes have propagation loss of 1.8dB/mm and bend loss of 0.14dB/90 degrees for bends with radius of 5 mu m.

The Kiloparsec-scale structure of 3C 286

We present radio images of the compact steep spectrum (CSS) quasar 3C 286 acquired with the Very Large Array (VLA) at 8.4 and 22.5 GHz. The source exhibits a two-sided core-jet structure with a bright central component and two extended components one to the east (P.A. 100degrees) and another to the southwest (P.A. -116degrees). From the compact core, an extension runs towards the southwest component up to similar to 0.7 arcsecond. The emission between the primary central component and the southwest component exhibits a knotty structure. A gradual change of the jet position angles from -135degrees to -120degrees in the inner southwest jet suggests a local bend. The position angle changes of the major eastern components E2 and E1 suggest that the eastern jet likely follows a curved trace. The bends in the jet trace may be associated with a relativistic precession or some interaction between the jet and the ambient matter. A mean spectral index of alpha(8.4)(22.5) similar to -0.76 (S-nu proportional to nu(alpha)) is estimated for the core component. Steep spectra are also obtained for the extended southwest component (2.6", P.A. -116degrees) and eastern component (0.8", P.A. 100degrees), with alpha(8.4)(22.5) similar to -0.88 and alpha(8.4)(22.5) similar to -1.79, respectively. The radio morphologies and spectral index distributions suggest that the core seen in our images is likely to be the beamed inner jet while the real nucleus is dimmed by it beaming away from us.