光学薄膜中界面层和表面吸附层对相位延迟的影响

多层介质反射镜在非正入射的时候，两个不同的偏振态之间会产生不同的相移．根据空气与膜层、膜层之间的实际情况，建立了界面层和表面吸附层模型，并运用它分析相位延迟产生误差的原因．通过优化设计，入射角为54°，在1285～1345nm之间p，s波获得了270±1°的相移，同时也使反射率在99．5％以上．用离子束溅射技术制备相位延迟膜，用分光光度计测试了光谱特性和用椭偏仪测试了相位特性，在相应波段获得了262．4±1．8°的相移，同时也使反射率在99．6％以上．误差的主要来源是离子源工作特性会产生不均匀的过渡层和最

氧碘激光器相位延迟片的制备与性能研究

多层介质反射镜在非正入射的时候，两个不同的偏振态之间会产生不同的相移。利用矩阵法，根据菲涅耳公式和电磁场边界条件，推导出p，s波的相移。通过优化设计．入射角为54°，在1285～1345nm之间p，s波获得了270°±1°的相移，同时也使反射率在99．5％以上。用离子束溅射技术制备相位延迟膜，用分光光度计测试了光谱特性和用椭偏仪测试了相位特性，在相应波段获得了262．4°±1．8°的相移，同时也使反射率在99．6％以上。误差的主要来源是离子源工作特性会产生不均匀的过渡层和最外层会吸收一些水气、灰尘等也产生

反射式相位延迟器的性能研究

多层介质反射镜在非正入射的时候，两个不同的偏振态之间会产生不同的相移。通过优化设计，入射角为45°，在1285～1345nm之间p，s波获得了270°±0．15°的相移和99．5％以上的反射率。对使用的膜系进行了每层光学厚度的误差分析。用离子柬溅射技术制备相位延迟膜，在大气中对样品进行不同温度的退火，用分光光度计测试了光谱特性和用椭偏仪测试了相位特性。结果表明，未退火的样品在相应波段获得了267．5°±0．5°的相移和99．6％以上的反射率；根据拟合分析，最外层的误差和折射率与设计值的偏差是发生相移偏小的

渐变反射率镜的设计与制备

按照高斯型渐变反射率镜(GRM)的参数要求,采用了中间层厚度渐变的方案对膜系和掩模板形状进行设计.根据薄膜的实际需求和具体的沉积设备,设计了掩模和掩模切换装置.在一次高真空环境下镀制了渐变反射率镜的所有膜系.采用直接测量的方法,测量了高斯型渐变反射率镜反射率的径向分布.测试结果表明,用这种技术制备的样品,与设计要求基本一致.分析得出,掩模板形状与精度对镀制结果有影响.随着设计尺寸减小,掩模板对膜料分子的散射作用增强,使样品中心反射率小于设计要求,边缘出现旁瓣.提出了减小基片与掩模板之间的距离和提高膜厚监控的精度的改善方案.

Techniques for fabrication of large-size graded reflectivity mirrors

According to the parameter requirements of a graded reflectivity mirror with a Gaussian profile, the layer structure and the mask pattern are designed using a graded-thickness middle layer. The mask and the automatic mask-switchover equipment are designed considering the actual requirement of the thin films and the specific deposit facility. The uniformity of the layer thickness is analyzed. The measurement results indicate that samples prepared with this technique are basically in accordance with the design parameter. The scattering effect between the material molecules and the mask, thickness errors, and the alignment error between the mask and the substrate are the main factors that influence the deposit result. (c) 2008 Society of Photo-Optical Instrumentation Engineers. [DOI: 10.1117/1.3027595]

低损耗193nm反射膜的设计

采用1/4规整膜系,从电场强度、吸收损耗及散射损耗的分布几个方面,对影响193 nm反射膜性能的因素进行了分析。以分析结果为基础,对低损耗193 nm反射膜的设计进行了探讨。结果表明:在空气侧的外膜层中电场强度较大,随着层数向内过渡,电场强度迅速减小;高折射率材料膜层的吸收损耗明显高于低折射率材料膜层的吸收损耗,而且靠近空气侧最外层的高折射率膜层的吸收损耗最大;按由外层向内层过渡的方向,吸收损耗迅速减小,减小的速度与高低折射率材料折射率的比值相关;表面散射损耗与两种材料的折射率比值成正比,但折射率比值减小后只能通过增加膜层数来获得一定的反射率,而这样又会使表面粗糙度增加,并且引入其它的损耗。因此,选择折射率差值适当大一些的材料对降低散射损耗是有利的。设计了27层膜堆的193 nm反射膜,设计反射率在98%以上。

Influence of ZrO2 in HfO2 on reflectance of HfO2/SiO2 multilayer at 248 nm prepared by electron-beam evaporation

Influence of ZrO2 in HfO2 on the reflectance of HfO2/SiO2 multilayer at 248 nm was investigated. Two kinds of HfO2 with different ZrO2 content were chosen as high refractive index material and the same kind of SiO2 as low refractive index material to prepare the mirrors by electron-beam evaporation. The impurities in two kinds of HfO2 starting coating materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum (GDMS) technology and secondary ion mass spectrometry (SIMS) equipment, respectively. It showed that between the two kinds of HfO2, either the bulk materials or their corresponding films, the difference of ZrO2 was much larger than that of the other impurities such as Ti and Fe. It is the Zr element that affects the property of thin films. Both in theoretical and in experimental, the mirror prepared with the HfO2 starting material containing more Zr content has a lower reflectance. Because the extinction coefficient of zirconia is relatively high in UV region, it can be treated as one kind of absorbing defects to influence the optical property of the mirrors. (C) 2008 Elsevier B.V. All rights reserved.

饥饿和饱食状态下丰鲤与其亲本的活动水平和活动节律

使用Videomex-V影像运动监视系统全天监测丰鲤(Cyprinus carpiovar.Xingguo♀×Cyprinus carpiovar.mirror splittered♂)、散鳞镜鲤(Cyprinus carpiovar.mirror splittered♂)和兴国红鲤(Cyprinus carpiovar.Xingguo♀)的活动(每种鱼12条,饥饿和饱食各6条)。结果显示,3种鱼饥饿时的活动水平都显著低于饱食时,但3种鱼白昼或夜间的相对活动水平都不受摄食与否的显著影响;饥饿或饱食时,丰鲤

Determination of the surface area of common carp, Cyprinus carpio L.

A wrap method adaptation combined with AutoCAD2005 and Scion Image for Windows were used to determine the surface area of a fish. Compared with the corresponding r(2) and F of many models, the most accurate formula: S = 752.15W(0.675) (r(2) = 0.999, F = 18362.94, P < 0.0001) for estimating the surface area of common carp was obtained. Similarly, the fin formula: S = 1834.12W(0.708) (r(2) = 0.992, F = 2690.47, P < 0.0001) was also obtained for the same purpose. It was proven that these two formulae gave good estimates of surface and fin areas of four strains of common carp: Yellow-river carp, fancy carp, mirror carp and Xingguo red carp.

Molecular phylogeny of three subspecies of common carp Cyprinus carpio, based on sequence analysis of cytochrome b and control region of mtDNA

The complete cytochrome b and the control region of mtDNA (about 2070 bp in total) of 10 strains belonging to three subspecies of the common carp, including three wild subspecies (the Yangtze River wild common carp - Cyprinus carpio haematopterus, Yuanjiang River wild common carp Cyprinus carpio rubrofuscus and Volga River wild common carp - Cyprinus carpio carpio) and seven domestic strains (Xingguo red carp, Russian scattered scaled mirror carp, Qingtian carp, Japanese Koi carp, purse red carp, Big-belly carp, German mirror carp) were sequenced. Phylogenetic analysis indicated that the 10 strains form three distinct clades, corresponding to C. c. haematopterus, C. c. rubrofuscus and C. c. carpio respectively. Purse red carp, an endemic domestic strain in Jiangxi province of China, showed a higher evolution rate in comparison with the other strains of C. c. haematopterus, most probably because of intensive selection and a long history of domestication. Base variation ratios among the three subspecies varied from 0.78% (between C. c. haematopterus and C. c. rubrofuscus) to 1.47%(between C. c. carpio and C. c. rubrofuscus). The topography of the phylogenetic tree and the geographic distribution of three subspecies closely resemble each other. The divergence time between C. c. carpio and the other two subspecies was estimated to be about 0.9 Myr and about 0.5 Myr between C. c. haematopterus and C. c. rubrofuscus. Based on phylogenetic analysis, C. c. rubrofuscus might have diverged from C. c. haematopterus.

Genetic variation analysis within and among six varieties of common carp (Cyprinus carpio L.) in china using microsatellite markers

Five microsatellites were used to study the genetic diversity and genetic structure of one wild and five domestic varieties of common carp in China (the Yangtze River wild common carp, Xingguo red carp, purse red carp, Qingtian carp, Russian scattered scaled mirror carp and Japanese decorative carp). All loci in this study showed marked polymorphism with the number of alleles ranging from 4 to 13. Domestic varieties (except Xingguo red carp) showed less genetic diversity than the Yangtze River wild common carp in terms of allelic diversity. Population differentiation was assessed and each combination of populations displayed significant differentiation (P < 0.05) with the exception of that between the Yangtze River wild common carp and Xingguo red carp. Genetic distance analysis (Nei's standard genetic distance and pairwise F-st distance) showed that the largest distance was between Russian scattered scaled mirror carp and the Yangtze River wild common carp and the smallest distance was between the Yangtze River wild common carp and Xingguo red carp. However, among six populations Japanese decorative carp displayed the highest level of variability in terms of heterozygosity.

Genetic divergence between Cyprinus carpio carpio and Cyprinus carpio haematopterus as assessed by mitochondrial DNA analysis, with emphasis on origin of European domestic carp

Although common carp is the major fish species in Asian and European aquaculture and many domestic varieties have occurred, there is a controversy about the origination of European domestic common carp. Some scientists affirmed that the ancestor of European domestic common carp was Danube River wild common carp, but others considered it might be Asian common carp. For elucidating origination of European domestic common carp, we chose two representative European domestic common carp strains (German mirror carp and Russian scattered scaled mirror carp) and one wild common carp strain of Cyprinus carpio carpio subspecies (Volga River wild common carp) and two Asian common carp strains, the Yangtze River wild common carp (Cyprinus carpio haematopterus) and traditionally domestic Xingguo red common carp, as experimental materials. ND5-ND6 and D-loop segments of mitochondrial DNA were amplified by polymerase chain reaction and analyzed through restriction fragment length polymorphism (RFLP) and sequencing respectively. The results revealed that HaeIII and DdeI digestion patterns of ND5-ND6 segment and sequences of control region were different between European subspecies C. carpio carpio and Asian subspecies C. carpio haematopterus. Phylogenetic analysis showed that German mirror carp and Russian scattered scaled mirror carp belonged to two subspecies, C. carpio carpio and C. carpio haematopterus, respectively. Therefore, there were different ancestors for domestic carp in Europe: German mirror carp was domesticated from European subspecies C. carpio carpio and Russian scattered scaled mirror carp originated from Asian subspecies C. carpio haematopterus.

Mode Characteristics for Square Resonators With a Metal Confinement Layer

Microsquare resonators laterally confined by SiO2/Au/air multilayer structure are investigated by light ray method with reflection phase-shift of the multiple layers and two-dimensional (2-D) finite-difference time-domain (FDTD) technique. The reflectivity and phase shift of the mode light ray on the sides of the square resonator with the semiconductor/SiO2/Au/air multilayer structure are calculated for TE and TM modes by transfer matrix method. Based on the reflection phase shift and the reflectivity, the mode wavelength and factor are calculated by the resonant condition and the mirror loss, which are in agreement well with that obtained by the FDTD simulation. We find that the mode factor increases greatly with the increase of the SiO2 layer thickness, especially as d < 0.3 mu m. For the square resonator with side length 2 mu m and refractive index 3.2, anticrossing mode couplings are found for confined TE modes at wavelength about 1.6 mu m at d = 0.11 mu m, and confined TM modes at d = 0.71 mu m, respectively.

Passively mode-locked YVO4/Nd : YVO4 composite crystal laser with a semiconductor saturable absorber as a high reflector

A passively mode-locked diode end-pumped YVO4/Nd:YVO4 composite crystal laser with a five-mirror folded cavity was first demonstrated in this paper by using a low temperature semiconductor saturable absorber mirror grown by metal organic chemical vapor deposition. Both the Q-switching and continuous-wave mode locking operation were realized experimentally. A stable averaged output power of 10.15 W with pulse width of about 11.2-ps at a repetition rate of 113 MHz was obtained, and the optical-to-optical efficiency of 43% was achieved.

Experimental study on a diode-pumped passively mode-locking Nd : GdVO4/SESAM laser

We demonstrate a low-threshold and efficient diode-pumped passively continuous wave (CW) mode-locked Nd:GdVO4 laser with a reflective semiconductor saturable absorber mirror (SESAM). The threshold for the continuous wave was 0.36 W, and it is the lowest threshold for a continuous wave in a passively mode-locked Nd:GdVO4 laser to our knowledge. The maximum average output power of 1.82 W was obtained at a pump power of 6.65 W with a slope efficiency of about 29%. The CW mode-locked pulse duration was measured to be about 10.5 ps with a 116-MHz repetition rate.