Synthesis and structures of morphology-controlled ZnO nano- and microcrystals

Zinc oxide flower-like bunches were directly synthesized on indium-doped tin oxide (ITO) glass substrates through a simple chemical bath deposition process. By adjusting precursor concentration, other morphologies ( spindles and rods) were also obtained. All of them are hexagonal and single crystalline in nature and grow along the [ 0001] crystallographic direction. The possible growth mechanisms for these nano- and microcrystals were proposed. It was revealed that both the inherent highly anisotropic structure of ZnO and the precursor concentration play crucial roles in determining final morphologies of the products. In addition, vibrational properties of ZnO crystals with different morphologies were investigated by Raman spectroscopy.

Novel photonic crystal structure GaN-based light-emitting diodes - art. no. 68410J

For enhancing the output efficiency of GaN light-emitting diode(LED), we calculated the band structure of photonic crystal(PhC), and designed and fabricated several novel GaN LEDs with photonic crystal on Indium-Tin-Oxide(ITO), which as p-type transparent contact of GaN LED. In this fabricating process, we developed conventional techniques in order that these methods can be easily applied to industrial volume-production. And we have done some preliminary experiments and obtained some results.

Enhancing the Performance of the Organic Light-emitting Device (OLED) by Thermal Treatment

A comparative study on the annealing of the ITO substrates and the organic layers were conducted on Organic light-emitting device (OLED). We fabricated four devices with the structure of Al/Alq(3)/TPD: PVK/NiO/ITO/Glass, and investigated the effect of heat on device performance by selectively annealing. When the TPD: PVK layers were annealed at 90 degrees C with 30 min annealing time and the ITO substrates were annealed at 300 degrees C with a constant annealing time (100 min). We find the OLED shows obvious performance improvement in brightness and current efficiency, which is attributable to the fact that annealing reduces defects and improves the interface structures of the organics and the organic/ITO interfaces. On the other hand, an appropriate annealing would slow the transportation of the hole, thus finally leads to more balanced electron and hole.

Synthesis and near-infrared luminescent properties of some ruthenium complexes

A series of seven ruthenium complexes with different ligands were synthesized and their optical, electrochemical and photoluminescent properties were characterized. Electroluminescent properties of these complexes were further evaluated using a light-emitting electrochemical cell with a configuration of indium tin oxide (ITO)/complex (100 nm)/Au (100 nm).

Magnet-assisted assembly of 1-dimensional hollow PtCo nanomaterials on an electrode surface

In this work, rapid and controllable confinement of one-dimensional (1D) hollow PtCo nanomaterials on an indium tin oxide (ITO) electrode surface was simply realized via magnetic attraction. The successful assembly was verified by scanning electron microscopy (SEM) and cyclic voltammetry, which showed that a longer exposure time of the electrode to the suspension of these 1D hollow nanomaterials (magnetic suspension) led to a larger amount of attached 1D hollow PtCo nanomaterials.

Metal nanomaterials and carbon nanotubes - synthesis, functionalization and potential applications towards electrochemistry

This review focuses on the synthesis, assembly, surface functionalization, as well as application of inorganic nanostructures. Electrochemical and wet- chemical methods are demonstrated to be effective approaches to make metal nanostructures under control without addition of a reducing agent or protecting agent. Owing to the unique physical and chemical properties of the nano-sized materials, novel applications are introduced using inorganic nanomaterials, such as electrocatalysis, photoelectricity, spectrochemistry, and analytical chemistry.

Facile electrochemical approach to fabricate hierarchical flowerlike gold micro structures: Electrodeposited superhydrophobic surface

A templateless, surfactantless, electrochemical approach is proposed to directly fabricate hierarchical flowerlike gold microstructures (HFGMs) on an indium tin oxide (ITO) substrate. The as-prepared HFGMs have been characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and cyclic voltammetry.

[Ru(bpy)(3)](2+)-doped silica nanoparticles within layer-by-layer biomolecular coatings and their application as a biocompatible electrochemiluminescent tag material

[Ru(bpy)(3)](2+)-doped silica (RuSi) nanoparticles were synthesized by using a water/oil microemulsion method. Stable electrochemiluminescence (ECL) was obtained when the RuSi nanoparticles were immobilized on a glassy carbon electrode by using tripropylamine (TPA) as a coreactant. Furthermore, the ECL of the RuSi nanoparticles with layer-by-layer biomolecular coatings was investigated. Squential self-assembly of the polyelectrolytes and biomolecules on the RuSi nanoparticles gave nanocomposite suspensions, the ECL of which decreased on increasing the number of bilayers.

A soluble nonionic surfactant as electron injection material for high-efficiency inverted bottom-emission organic light emitting diodes

A soluble nonionic surfactant, polyethylenimine 80% ethoxylated (PEIE) solution, was used as the electron injection material in inverted bottom-emission organic light emitting diodes (OLEDs). The transparent PEIE film was formed on indium-tin-oxide cathode by simple spin-coating method and it was found that the electron injection was greatly enhanced. The devices with PEIE electron injection layer had achieved significant enhancement in luminance and efficiency. The maximum luminance reached 47 000 cd/m(2), and the maximum luminance efficiency and power efficiency arrived at 19.7 cd/A and 10.6 lm/W, respectively.

Cesium hydroxide doped tris-(8-hydroxyquinoline) aluminum as an effective electron injection layer in inverted bottom-emission organic light emitting diodes

We demonstrate highly efficient inverted bottom-emission organic light-emitting diodes (IBOLEDs) by using cesium hydroxide (CsOH) doped tris-(8-hydroxyquinoline) aluminum (Alq(3)) as the electron injection layer on indium tin oxide cathode, which could significantly enhance the electron injection, resulting in a large increase in luminance and efficiency. The maximum luminance, current efficiency, and power efficiency reach 21 000 cd/cm(2), 6.5 cd/A, and 3.5 lm/W, respectively, which are 40%-50% higher in efficiency than that of IBOLEDs with cesium carbonate (Cs2CO3) doped Alq(3) as the electron injection layer, where the efficiencies are only 4.5 cd/A and 2.2 lm/W.

Efficient white organic light-emitting diodes using europium complex as the red unit

Efficient white organic light-emitting diodes (WOLEDs) using europium complex as the red unit are presented. The WOLEDs were fabricated by using the structure of indium tin oxide (ITO)/N, N'-di(naphthalene-1-yl)-N, N'-diphenyl-benzidine (NPB)/4,4-N, N-dicarbazolebiphenyl (CBP) : bis(2,4-diphenylquinolyl-N, C-2) iridium (acetylacetonate) ((PPQ)(2)Ir(acac)) : Eu (III) tris(thenoyltrifluoroacetone) 3,4,7,8-tetramethyl-1,10-phenanthroline (Eu(TTA)(3)(Tmphen))/NPB/2-methyl-9,10-di(2-naphthyl)anthracene (MADN) : p-bis (p-N, N-di-phenyl-aminostyryl)benzene (DSA-Ph)/9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP)/tris(8-hydroxyquinoline) aluminium (Alq3)/LiF/Al.

Al/WO3/Au as the interconnecting layer for efficient tandem white organic light-emitting diodes

White light emission from tandem organic light-emitting diodes consisting of blue and red light units separated by a transparent interconnecting layer of Al/WO3/Au has been realized. The devices have a structure of indium-tin-oxide (ITO)/molybdenum oxide (MoO3) (8 nm)/N, N'-di(naphthalene-1-yl)-N, N'-diphenyl-benzidine (NPB)(100 nm)/p-bis(p-N, N-diphenyl-aminostyryl) benzene) (DSA-ph): 2-methyl-9,10-di(2-naphthyl) anthracene (MADN)(40 nm)/tris(8-hydroxylquinoline) aluminium (Alq(3)) (10 nm)/LiF(1 nm)/Al(2 nm)/WO3(3 nm)/Au(16 nm)/MoO3(5 nm)/NPB(60 nm)/Alq(3): 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB)(30 nm)/Alq3(30 nm)/LiF(1 nm)/Al(150 nm).

Fabrication of an integrated pixel with an organic light-emitting diode driven by copper phthalocyanine organic thin film transistors

An organic integrated pixel with organic light-emitting diodes (OLEDs) driven by organic thin film transistors (OTFTs) is fabricated by a greatly simplified processing. The OTFTs are based on copper phthalocyanine as the active medium and fabricated on indium-tin-oxide (ITO) glass with top-gate structure, thus an organic integrated pixel is easily made by integrating OLED with OTFT. The OTFTs show field-effect mobility of 0.4 cm(2) /Vs and on/off ratio of 10(3) order. The OLED is driven well and emits the brightness as large as 2100cd/m(2) at a current density of 14.6 mu A/cm(2) at -19.7 V gate voltage. This simple device structure is promising in the future large-area flexible OLED displays.

Biomolecule-nanoparticle hybrids for electrochemical biosensors

Inorganic nanoparticles (NPs) with attractive electronic, optical, magnetic, thermal and catalytic properties have attracted great interest due to their important applications in physics, chemistry, biology, medicine, materials science and interdisciplinary fields. Biomolecule-NP hybrid systems, which combine recognition and catalytic properties of biomolecules with electronic, optical, magnetic and catalytic properties of NPs, are particularly new materials with synergistic properties originating from the components of the hybrid composites. The biomolecule-NP hybrid system has excellent prospects for interfacing biological recognition events with electronic signal transduction so as to design a new generation of bioelectronic devices with high sensitivity.

Origin of improvement in device performance via the modification role of cesium hydroxide doped tris(8-hydroxyquinoline) aluminum interfacial layer on ITO cathode in inverted bottom-emission organic light-emitting diodes

It has been found that cesium hydroxide (CsOH) doped tris(8-hydroxyquinoline) aluminum (Alq(3)) as an interfacial modification layer on indium-tin-oxide (ITO) is an effective cathode structure in inverted bottom-emission organic light-emitting diodes (IBOLEDs). The efficiency and high temperature stability of IBOLEDs with CsOH:Alq(3) interfacial layer are greatly improved with respect to the IBOLEDs with the case of Cs2CO3:Alq(3). Herein, we have studied the origin of the improvement in efficiency and high temperature stability via the modification role of CsOH:Alq(3) interfacial layer on ITO cathode in IBOLEDs by various characterization methods, including atomic force microscopy (AFM), ultraviolet photoemission spectroscopy (UPS), X-ray photoemission spectroscopy (XPS) and capacitance versus voltage (C-V). The results clearly demonstrate that the CsOH:Alq(3) interfacial modification layer on ITO cathode not only enhances the stability of the cathode interface and electron-transporting layer above it. which are in favor of the improvement in device stability, but also reduces the electron injection barrier and increases the carrier density for current conduction, leading to higher efficiency.