基于光谱分析的主动式距离图象获取方法

Ｒａｉｎｂｏｗ 三维摄像机是一种基于光谱分析的快速三维信息获取方法。该方法利用连续变化的彩色光谱照射景物，彩色ＣＣＤ 摄像机摄取的景物图象将呈现有规律的颜色变化，而且不同的颜色（波长）构成了不同的空间颜色面。通过标定这些颜色面和摄像机成象模型，即可计算出图象中各点的三维坐标。该文重点讨论实现该方法的标定技术和颜色分类技术，最后给出实验结果。

小湾电站坝基岩体卸荷工程地质力学研究

Dam is the key main works in the construction of water power. The success or failure of the construction of the dam mainly depends on the stability of the dam foundation. The double curvature arch dam-XiaoWan Dam is the highest one among the dams with the same type in the world, and the water thrust acted on it reaches ton, so the rock bearing capacity of dam foundation becomes more important. Because of the high and steep valley-side slope, the large scale of excavation and the complex body type of excavation, it is prominent that the problem of stress release of the rock mass in dam foundation. More great attentions should be paid for the stability and the degraded of rock properties of rock mass induced by the stress release. In this paper, the phenomena of stress release of rock mass in XiaoWan Dam foundation and its mechanisms were analyzed based on the collection of data, the detailed field engineering investigations, measurement of the rock mass and the 2D numerical calculations. The rock mass under the foundation is weak-weathered to intact, the quality of which is good. After excavation of the foundation, the rock mass near the slope surface occurred extend, stretch and stick-slip along original textures till the new fracture surface formed. Then platy structure of the rock mass takes on. The rock mass in the dam foundation occur resilience due to stress release towards free faces with the characteristics of time effect and localized deformation. In-situ measurements show that the rock mass near the surface are degraded. The stress release induced by excavation is a process of the interaction between engineering structures and geologic body. The stress release of rock mass in dam foundation is related to the changed degree of geometrical conditions. The rock near excavation surface failed nearly under uniaxial stresses. The bending-breaking mechanism of plate girder can interpret the failure model of the rock mass with platy structure in dam foundation slope. In essence, the stress release is the change of stress field including the change of directions and magnitudes of stress induced by excavation, which can induce the comedown of the safety margin. In this paper, the inducing conditions of stress release were calculated by numerical analyses. Moreover, from the point of view that the change of stress field, the coefficient of K, i.e. the variable load coefficient was proposed. Then the law of the change of it is interpreted. The distributional characteristics of fracture zone were expressed by the coefficient. The stress release of hard rock has the characteristic of localization. The measuring technique of sound wave can not reflect the small cracks in this kind of rock mass due to stress release. So, the spectral analysis method was proposed. At the same time, the application foreground in engineering of the Stockwell Time-Frequency- Spectrum method was discussed with a view to the limitation of it.

黄土高原中部60万年来黄土—古土壤序列有机碳同位素研究

Vegetation is very sensitive to climate change. Carbon isotopes in paleosol have been widely used to contruct the propotion of plants using C3 and C4 photosynthetic pathways. δ13C of Loess organic matter were analyzed on the loess- paleosols samples from Jingchuan sections and Luochuan S4—S5 sequence. This paper presents a long carbon isotope time series, covering the last 600kyr. δ13C record of Loess organic matter in Jingchuan is correlated with marine oxygen isotope records. Basing on former research work, this paper discusses temperature, rainfall and P CO2 effect on δ13Corg value. In the interglacial periods, carbon isotope is more sensitive than other proxies and indicates several climate fluctuations. The main conclusions are as follows: 1. Obtained δ13C composition from paleosols and loess sediments in Jingchuan range of -20.0‰ to -24.6‰, the maximum biomass of C4 is 35%, indicating a C3 and C4 mixed steppe with C3 dominated. C4 plant is not always expansion during paleosols periods. The minimum values of Jingchuan section appeared in S4 soil, and the vegetation was almost pure C3 plant at that time. δ13Corg value in S5-2 is also lower than loess in S5, reaching the minimum valus of S5 soil. 2. PCO2 variation has little impact on δ13Corg value in interglacial periods for the last 600kyr. The correlation between δ13Corg value curve and magnetic susceptibility curve as proxy of summer monsoon in general, means summer monsoon drive C4 plant expansion during glacial and interglacial. 3. The lowerδ13Corg values in S4 and S5-2 appear at Jingchuan and Luochuan, suggest origin from woodland or C3 grassland. Whatever vegetation it is, indicate strengthened East Asian summer monsoon and increase of precipitation. C4 plant percentage is lower in S5-1 and S1 which have stronger summer monsoon, than S0 and S2. And it also indicates increase of precipitation.δ13Corg values has not always non-linearity correlation with summer monsoon. 4. The maximum entroy spectral analysis of δ13C values of the last 600kyr indicates there is 21 kyr cycles in Loess sequence. It means that summer monsoon in the Chinese Loess Plateau also has the precession cycles like its origin low latitude.

电离层行进式扰动的GPS台网监测研究

In this dissertation, we investigated two types of traveling ionospheric disturbances (TIDs)/gravity waves (GWs) triggered separately by auroral energy input during super geomagnetic storms and solar terminator (ST) under quiet geomagnetic conditions (kp<3+) using TEC measurements from the global network of GPS receivers. Research into the generation and propagation of TIDs/GWs during storms greatly enhance our understandings on the evolution processes of energy transportation from the high-latitude’s magnetosphere to the low-latitude ionosphere and the conjugated effect of TIDs propagation between the northern and southern hemispheres. Our results revealed that the conjugacy of propagation direction between the northern and southern hemispheres was subject to the influence of Coriolis force. We also figure out the evolution processes of ionospheric disturbances at the global scale. These are important topics that had not been well addressed previously. In addition, we also obtained thee wave structures of medium scale TIDs excited by the solar terminator (ST) moving over the northern America and physical mechanisms involved. Our observations confirm that the ST is a stable and repetitive source of ionospheric wave disturbances and the evidence of solar terminator generated disturbances has been demonstrated experimentally via the GPS TEC measurement. The main researches and results of this dissertation are as follows. First, the global traveling ionospheric disturbances (TIDs) during the drastic magnetic storms of October 29–31, 2003 were analyzed using the Global Position System (GPS) total electron content (TEC) data observed in the Asian-Australian, European and North American sectors. We collected the most comprehensive set of the TEC data from more than 900 GPS stations on the International GNSS Services (IGS) website and introduce here a strategy that combines polynomial fitting and multi-channel maximum entropy spectral analysis to obtain TID parameters. Moreover, in collaboration with my thesis advisor, I have developed an imaging technique of 2-dimensional map of TIDs structures to obtain spatial and temporal maps of large scale traveling ionospheric disturbances (LSTIDs). The clear structures of TEC perturbations map during the passage of TIDs were displayed. The results of our study are summarized as follows: (1) Large-scale TIDs (LSTIDs) and medium-scale TIDs (MSTIDs) were detected in all three sectors after the sudden commencement (SC) of the magnetic storm, and their features showed longitudinal and latitudinal dependences. The duration of TIDs was longer at higher latitudes than at middle latitudes, with a maximum of about 16 h. The TEC variation amplitude of LSTIDs was larger in the North American sector than in the two other sectors. At the lower latitudes, the ionospheric perturbations were more complicated, and their duration and amplitude were relatively longer and larger. (2) The periods and phase speeds of TIDs were different in these three sectors. In Europe, the TIDs propagated southward; in North America and Asia, the TIDs propagated southwestward; in the near-equator region, the disturbances propagated with the azimuth (the angle of the propagation direction of the LSTIDs measured clockwise from due north with 0°) of 210° showing the influence of Coriolis force; in the Southern Hemisphere, the LSTIDs propagated conjugatedly northwestward. Both the southwestward and northeastward propagating LSTIDs are found in the equatorial region. These results mean that the Coriolis effect cannot be ignored for the wave propagation of LSTIDs and that the propagation direction is correlated with the polar magnetic activity. (3) The day (day of year: 301) before the SC (sudden commencement) of magnetic storm, we observed a sudden TEC skip disturbances (±10 TECU). It should be a response for the high flux of proton during the solar flare event, but not the magnetic storms. Next, the most comprehensive and dense GPS network’s data from North-America region were used in this paper to analyze the medium scale traveling ionospheric disturbances (MSTIDs) which were generated by the moving solar terminator during the quiet days in 2005. We applied the multi-channel maximum entropy spectral analysis to calculated TID parameters, and found that the occurrence of ST-MSTIDs depends on the seasonal variations. The results of our study are summarized as follows: (1) MSTIDs stimulated by the moving ST (ST-MSTIDs) are detected at mid-latitudes after the passage of the solar terminator with the life time of 2～3 hours and the variation amplitude of 0.2～0.8 TECU. Spectral analysis indicated that the horizontal wavelength, average period, horizontal phase velocity of the MSTIDs are around 300±150 km，150±80 m/s and 25±15 min, respectively. In addition, ST-MSTIDs have wave fronts elongating the moving ST direction and almost parallel to ST. (2) The statistical results demonstrate that the dusk MSTIDs stimulated by ST is more obvious than the dawn MSTIDs in summer. On the contrary, the more-pronounced dawn MSTIDs occurs in winter. (3) Further analysis indicates that the seasonal variations of ST-MSTIDs occurrence frequency are most probably related to the seasonal differences of the variations of EUV flux in the ionosphere region and recombination process during sunrise and sunset period at mid-latitudes. Statistical study of occurrence characteristics of TIDs using the GPS network in North-American and European during solar maximum, In conclusion, statistical studies of the propagation characteristics of TIDs, which excited by the two common origins including geomagnetic storms and moving solar terminator, were involved with global GPS TEC databasein this thesis. We employed the multichannel maximum entropy spectral analysis method to diagnose the characteristics of propagation and evolvement of ionospheric disturbances, also, the characteristics of their regional distribution and climatological variations were revealed by the statistic analysis. The results of these studies can improve our knowledge about the energy transfer in the solar-terrestrial system and the coupling process between upper and lower atmosphere (thermosphere-ionosphere-mesosphere). On the other hand, our results of the investigation on TIDs generated by particular linear origin such as ST are important for developing ionospheric irregularity physics and modeling the transionosphere radio wave propagation. Besides, the GPS TEC representation of the ST-generated ionospheric structure suggests a better possibility for investigating this phenomenon. Subsequently, there are scientific meaning of the result of this dissertation to deeply discuss the energy transfer and coupling in the ionosphere, as well as realistic value to space weather forecast in the ionosphere region.

HHT在电磁信号处理中的应用

In modem signal Processing，non－linear，non－Gaussian and non－stable signals are usually the analyzed and Processed objects，especially non－stable signals. The convention always to analyze and Process non－stable signals are： short time Fourier transform，Wigner－Ville distribution，wavelet Transform and so on. But the above three algorithms are all based on Fourier Transform，so they all have the shortcoming of Fourier Analysis and cannot get rid of the localization of it. Hilbert－Huang Transform is a new non－stable signal processing technology，proposed by N. E. Huang in 1998. It is composed of Empirical Mode Decomposition (referred to as EMD) and Hilbert Spectral Analysis (referred to as HSA). After EMD Processing，any non－stable signal will be decomposed to a series of data sequences with different scales. Each sequence is called an Intrinsic Mode Function (referred to as IMF). And then the energy distribution plots of the original non－stable signal can be found by summing all the Hilbert spectrums of each IMF. In essence，this algorithm makes the non－stable signals become stable and decomposes the fluctuations and tendencies of different scales by degrees and at last describes the frequency components with instantaneous frequency and energy instead of the total frequency and energy in Fourier Spectral Analysis. In this case，the shortcoming of using many fake harmonic waves to describe non－linear and non－stable signals in Fourier Transform can be avoided. This Paper researches in the following parts： Firstly，This paper introduce the history and development of HHT，subsequently the characters and main issues of HHT. This paper briefly introduced the basic realization principles and algorithms of Hilbert－Huang transformation and confirms its validity by simulations. Secondly, This paper discuss on some shortcoming of HHT. By using FFT interpolation, we solve the problem of IMF instability and instantaneous frequency undulate which are caused by the insufficiency of sampling rate. As to the bound effect caused by the limitation of envelop algorithm of HHT, we use the wave characteristic matching method, and have good result. Thirdly, This paper do some deeply research on the application of HHT in electromagnetism signals processing. Based on the analysis of actual data examples, we discussed its application in electromagnetism signals processing and noise suppression. Using empirical mode decomposition method and multi-scale filter characteristics can effectively analyze the noise distribution of electromagnetism signal and suppress interference processing and information interpretability. It has been founded that selecting electromagnetism signal sessions using Hilbert time-frequency energy spectrum is helpful to improve signal quality and enhance the quality of data.

两种超微细矿物粉体材料的制备及应用研究

Superfine mineral materials are mainly resulted from the pulverization of natural mineral resources, and are a type of new materials that can replace traditional materials and enjoy the most extensive application and the highest degree of consumption in the present day market. As a result, superfine mineral materials have a very broad and promising prospect in terms of market potential. Superfine pulverization technology is the only way for the in-depth processing of most of the traditional materials, and is also one of the major means for which mineral materials can realize their application. China is rich in natural resources such as heavy calcite, kaolin, wollastonite, etc., which enjoy a very wide market of application in paper making, rubber, plastics, painting, coating, medicine, environment-friendly recycle paper and fine chemical industries, for example. However, because the processing of these resources is generally at the low level, economic benefit and scale for the processing of these resources have not been realized to their full potential even up to now. Big difference in product indices and superfine processing equipment and technologies between China and advanced western countries still exists. Based on resource assessment and market potential analysis, an in-depth study was carried out in this paper about the superfine pulverization technology and superfine pulverized mineral materials from the point of mineralogical features, determination of processing technologies, analytical methods and applications, by utilizing a variety of modern analytical methods in mineralogy, superfine pulverization technology, macromolecular chemistry, material science and physical chemistry together with computer technology and so on. The focus was placed on the innovative study about the in-depth processing technology and the processing apparatus for kaolin and heavy calcite as well as the application of superfine products. The main contents and the major achievements of this study are listed as follows: 1. Superfine pulverization processing of mineral materials shall be integrated with the study of their crystal structures and chemical composition. And special attention shall be put on the post-processing technologies, rather than on the indices for particle size, of these materials, based on their fields of application. Both technical feasibility and economic feasibility shall be taken into account for the study about superfine pulverization technologies, since these two kinds of feasibilities serve as the premise for the industrialized application of superfine pulverized mineral materials. Based on this principle, preposed chemical treatment method, technology of synchronized superfine pulverization and gradation, processing technology and apparatus of integrated modification and depolymerization were utilized in this study, and narrow distribution in terms of particle size, good dispersibility, good application effects, low consumption as well as high effectiveness of superfine products were achieved in this study. Heavy calcite and kaolin are two kinds of superfine mineral materials that enjoy the highest consumption in the industry. Heavy calcite is mainly applied in paper making, coating and plastics industries, the hard kaolin in northern China is mainly used in macromolecular materials and chemical industries, while the soft kaolin in southern China is mainly used for paper making. On the other hand, superfine pulverized heavy calcite and kaolin can both be used as the functional additives to cement, a kind of material that enjoys the biggest consumption in the world. A variety of analytical methods and instruments such as transmission and scanning electron microscopy, X-ray diffraction analysis, infrared analysis, laser particle size analysis and so on were applied for the elucidation of the properties and the mechanisms for the functions of superfine mineral materials as used in plastics and high-performance cement. Detection of superfine mineral materials is closely related to the post-processing and application of these materials. Traditional detection and analytical methods for superfine mineral materials include optical microscopy, infrared spectral analysis and a series of microbeam techniques such as transmission and scanning electron microscopy, X-ray diffraction analysis, and so on. In addition to these traditional methods, super-weak luminescent photon detection technology of high precision, high sensitivity and high signal to noise ratio was also utilized by the author for the first time in the study of superfine mineral materials, in an attempt to explore a completely new method and means for the study of the characterization of superfine materials. The experimental results are really exciting! The innovation of this study is represented in the following aspects: 1. In this study, preposed chemical treatment method, technology of synchronized superfine pulverization and gradation, processing technology and apparatus of integrated modification and depolymerization were utilized in an innovative way, and narrow distribution in terms of particle size, good dispersibility, good application effects, low consumption as well as high effectiveness of superfine products were achieved in the industrialized production process*. Moreover, a new modification technology and related directions for producing the chemicals were invented, and the modification technology was even awarded a patent. 2. The detection technology of super-weak luminescent photon of high precision, high sensitivity and high signal to noise ratio was utilized for the first time in this study to explore the superfine mineral materials, and the experimental results can be compared with those acquired with scanning electron microscopy and has demonstrated its unique advantages. It can be expected that further study may possibly help to result in a completely new method and means for the characterization of superfine materials. 3. During the heating of kaolinite and its decomposition into pianlinite, the diffraction peaks disappear gradually. First comes the disappearance of the reflection of the basal plane (001), and then comes the slow disappearance of the (hkl) diffraction peaks. And this was first discovered during the experiments by the author, and it has never before reported by other scholars. 4. The first discovery of the functions that superfine mineral materials can be used as dispersants in plastics, and the first discovery of the comprehensive functions that superfine mineral materials can also be used as activators, water-reducing agents and aggregates in high-performance cement were made in this study, together with a detailed discussion. This study was jointly supported by two key grants from Guangdong Province for Scientific and Technological Research in the 10th Five-year Plan Period (1,200,000 yuan for Preparation technology, apparatus and post-processing research by using sub-micron superfine pulverization machinery method, and 300,000 yuan for Method and instruments for biological photon technology in the characterization of nanometer materials), and two grants from Guangdong Province for 100 projects for scientific and technological innovation (700,000 yuan for Pilot experimentation of superfine and modified heavy calcite used in paper-making, rubber and plastics industry, and 400,000 yuan for Study of superfine, modified wollastonite of large length-to-diameter ratio).

中新世秦安黄土一古土壤序列记录的古气候变化周期

Analysis of periodic oscillations of climate is very important in understanding the behavior of the climate system. Milankovitch hypothesis, which holds that the glacial-interglacial climatic cycles during the Quaternary were primarily driven by variations in orbital parameters, has been supported by substantial geological evidence. Continuous long-term and high-resolution records are crucial to detect how variations of Earth's orbital parameters affected climate before the Quaternary when the boundary conditions were significantly different. Qinan loess formed in the Miocene is nearly continuous aeolian deposit in northern China. Previous study has established a constrained chronology, which provides a basis to examine long-term climatic variations. One of important issues to untangle the mechanisms behind major climate changes is the investigation of climate cycles recorded in Qinan loess. In this paper, two climatic proxies, magnetic susceptibility and redness, are analyzed for QA-I section to evaluate climate cycles using Maximum entropy spectral analysis and Blackman-Tuckey method. Main conclusions are presented as following: Results exhibit significant peaks at periods of 100 ka, 64 ka, 41 ka, 30 ka and 23 ka, but also 1000 ka, 600 ka and 400 ka. These peaks correspond to the dominant periods of the Earth's orbit parameters, which indicates that the formation of the aeolian sediment in northern China might be primarily driven by variations in orbital parameters. Fluctuations with different cycles respectively dominated in different periods. Major shifts in the dominant cycles occurred at 20.3, 19.0, 17.9, 15.2, 12.5 and 11.3 Myr ago. The transition that happened at 17.9 Myr ago was synchronous with the uplift of the Tibetan Plateau, while others at 15.2, 12.5 and 11.3 Myr ago were in good agreement with the timing of the development of Antarctic ice sheet. Therefore we inferred that these shifts might be related to changes in global ice volume and/or the Tibetan uplift. 3. The strong period of 100 ka is observed between 17.9 and 15.2, and 12.5 and 11.3 Myr ago. Ice sheet-climate models that have been used to explain the cause of the 100 ka period since the middle Pleistocene couldn't be responsible for driving the 100 ka climate cycle in the Miocene in Northern China because of the different boundary of climatic conditions between the Quaternary and Miocene. Further investigation is needed to understand how this cycle became dominant in Qinan loess records during these two time segments.

Toeplitz矩阵的循环延拓及其分析与应用

In this paper, we have presented the combined preconditioner which is derived from k =±-1~(1/2) circulant extensions of the real symmetric positive-definite Toeplitz matrices, proved it with great efficiency and stability and shown that it is easy to make error analysis and to remove the boundary effect with the combined preconditioner. This paper has also presented the methods for the direct and inverse computation of the real Toeplitz sets of equations and discussed many problems correspondingly, especially replaced the Toeplitz matrices with the combined preconditoners for analysis. The paper has also discussed the spectral analysis and boundary effect. Finally, as an application in geophysics, the paper makes some discussion about the squared root of a real matrix which comes from the Laplace algorithm.

甘肃西峰晚第三纪红粘土地层中的蜗牛化石记录及其古环境意义

In this study, 260 mollusk fossil samples from a Red Clay sequence at Xifeng, Gansu province, in the northern China were analyzed quantitatively. 12 fossil species and four fossil zones have been identified. Three main ecological groups were determined based on ecological requirement of each mollusk taxon. According to fossil composition and succession of three ecological groups, the author discussed the origin and sedimentary environment of the red clay deposits, and the process of ecological environmental changes as well as the variations of the East Asia monsoons during 6.2-2.4 Ma in the Loess Plateau. A preliminary study on periodicity of paleoclimatic changes was also conducted by using spectral analysis method. The main results and conclusions are presented as follows:A continuous land mollusk fossil sequence of 6.2-2.4 Ma from Xifeng Red Clay Formation has been established, which provided a basic data for studying the environmental changes during late Miocene to Pliocene.The study of composition and preservation condition of mollusk fossils reveals a terrestrial in situ ecological population in the Red Clay Formation. All of identifiable mollusk species are composed of terrestrial taxa, which support the view that the Red Clay is an eolian origin, similar to the overlying Quaternary loess deposits.The mollusk record reveals the processes of ecological and environmental changes during 6.2-2.4 Ma in the Loess Plateau. Climatic changes experienced cold and dry from 6.2-5.4 Ma, warm and wet during 5.4-4.5 Ma, mild and moderate from 4.5-3-4 Ma, to rapid cooling and drying after 3.4 Ma. From '5.4- 2.4 Ma, climate was stepwise cooling. The cooling trend is in good agreement with a general1 0global cooling trend during this period, as documented by marine 5 0 records.4. Three remarked ecological shifts took place in mollusk assemblages from 6.2-2.4 Ma, focused on about 5.4, 4.5 and 3.4 Ma. The warming shift around 5.4 Ma was probably related to the rising of the global temperature. The cooling shifts around 4,5 and 3.4 Ma however might be closely linked to the uplift of Tibet Plateau and the development of Northern Hemisphere ice sheet.The succession in mollusk ecological groups also recorded the variability of the East Asian winter and summer monsoon. The winter monsoon dominated two periods from 6.2-5.4 Ma and from 3.4-2.4 Ma, while the summer monsoon was strong during 5.4-4.5 Ma. The variations in winter and summer monsoons were in phase during 4.5-3.4 Ma. Monsoon regimes changed with the duration about 1 Ma, which roughly corresponds to the cycle driven by tectonic activity on the time scales of ICP-IO7 years. In addition, mollusk fossils recorded the large amplitude and high frequency fluctuations overlapped on 105-107 years climate cycle.The maximum entropy spectral analysis and filter-band analysis of total mollusk individuals and three typical ecological groups suggest that the climate changes controlled mainly by solar insolation had periods about 70 ka and 40 ka on the time scales of 105 during late Miocene-Pliocene. Climatic periodicity intensified from 4.0 Ma, which reflected strengthened forcing by high latitude ice volume.

Factor analysis used to peak position optimization and spectral interference correction in inductively coupled plasma atomic emission spectrometry

Target transformation factor analysis was used to correct spectral interference in inductively coupled plasma atomic emission spectrometry (ICP-BES) for the determination of rare earth impurities in high purity thulium oxide. Data matrix was constructed with pure and mixture vectors and background vector. A method based on an error evaluation function was proposed to optimize the peak position, so the influence of the peak position shift in spectral scans on the determination was eliminated or reduced. Satisfactory results were obtained using factor analysis and the proposed peak position optimization method.

APPLICATION OF FACTOR-ANALYSIS TO CORRECTION OF SPECTRAL OVERLAP INTERFERENCE IN INDUCTIVELY COUPLED PLASMA ATOMIC EMISSION-SPECTROMETRY

Correction of spectral overlap interference in inductively coupled plasma atomic emission spectrometry by factor analysis is attempted. For the spectral overlap of two known lines, a data matrix can be composed from one or two pure spectra and a spectrum of the mixture. The data matrix is decomposed into a spectra matrix and a concentration matrix by target transformation factor analysis. The component concentration of interest in a binary mixture is obtained from the concentration matrix and interference from the other component is eliminated. This method is applied to correcting spectral interference of yttrium on the determination of copper and aluminium: satisfactory results are obtained. This method may also be applied to correcting spectral overlap interference for more than two lines. Like other methods of correcting spectral interferences, factor analysis can only be used for additive spectral overlap. Results obtained from measurements on copper/yttrium mixtures with different white noise added show that random errors in measurement data do not significantly affect the results of the correction method.

Cross spectral purity and its influence on ghost imaging experiments

Pseudo-thermal light has been widely used in ghost imaging experiments. In order to understand the differences between the pseudo-thermal source and thermal source, we propose a method to investigate whether a light source has cross spectral purity (CSP), and experimentally measure the cross spectral properties of the pseudo-thermal light source in near-field and far-field zones. Moreover we present a theoretical analysis of the cross spectral influence on ghost imaging. (c) 2006 Elsevier B.V. All rights reserved.

Analysis of an ultrashort pulsed finite beam diffracted by volume gratings

We obtain analytical solutions of the coupled wave equations that describe the Bragg diffraction of ultrashort pulsed finite beams by a thick planar grating, using two-dimensional coupled wave theory. The diffraction properties for the case of an ultrashort pulsed finite beam with Gaussian profiles in both the time and spatial domains are investigated. The spectral bandwidth of the diffracted beam, the Bragg selectivity bandwidth and the diffraction efficiency of the volume grating are influenced by the geometry parameter and the input bandwidth. Therefore extra attention should be paid to designing optical elements based on volume gratings for use with ultrashort pulsed waves in applications of pulse shaping and processing.

Numerical analysis and comparison of three metal-oxide-type super-resolution near field structures

Based on the Fresnel-Kirchkoff diffraction theory, we build up a Gaussian diffraction model of metal-oxide-type super-resolution near field structure (super-RENS), which can describe far field optical properties. The spectral contrast induced by refractive index and the structural changes in AgOx, PtOx and PdOx thin films, which are the key functional layers in super-RENS, are studied by using this model. Comparison results indicate that the spectral contrast intensively on laser-induced distribution and change of the refractive index in the metal-oxide films. The readout mechanism of the metal-oxide-type super-RENS optical disc is further clarified. This Gaussian diffraction model can be used as a simple and effective method for choosing proper active materials in super-RENS.