Photonic crystal point-shift nanolaser with ultimate small modal volume

A photonic crystal nanolaser consisting of only the shift of two lattice points was fabricated by HJ/Xe inductively coupled plasma etching. The room temperature lasing was observed by photopumping. The three-dimensional finite-difference time-domain calculation showed that the lasing mode has small modal volume close to (lambda/2n)(3).

Two-dimensional photonic band-gap defect modes with deformed lattice

A numerical study of the defect modes in two-dimensional photonic crystals with deformed triangular lattice is presented by using the supercell method and the finite-difference time-domain method. We find the stretch or shrink of the lattice can bring the change not only on the frequencies of the defect modes but also on their magnetic field distributions. We obtain the separation of the doubly degenerate dipole modes with the change of the lattice and find that both the stretch and the shrink of the lattice can make the dipole modes separate large enough to realize the single-mode emission. These results may be advantageous to the manufacture of photonic crystal lasers and provide a new way to realize the single-mode operation in photonic crystal lasers.

Calculation of propagation loss in photonic crystal waveguides by FDTD technique and Pade approximation

The propagation losses in single-line defect waveguides in a two-dimensional (2D) square-lattice photonic crystal (PC) consisted of infinite dielectric rods and a triangular-lattice photonic crystal slab with air holes are studied by finite-difference time-domain (FDTD) technique and a Pade approximation. The decaying constant beta of the fundamental guided mode is calculated from the mode frequency, the quality factor (Q-factor) and the group velocity v(g) as beta = omega/(2Qv(g)). In the 2D square-lattice photonic crystal waveguide (PCW), the decaying rate ranged from 10(3) to 10(-4) cm(-1) can be reliably obtained from 8 x 10(3)-item FDTD output with the FDTD computing time of 0.386 ps. And at most 1 ps is required for the mode with the Q-factor of 4 x 10(11) and the decaying rate of 10(-7) cm(-1). In the triangular-lattice photonic crystal slab, a 10(4)-item FDTD output is required to obtain a reliable spectrum with the Q-factor of 2.5 x 10(8) and the decaying rate of 0.05 cm(-1). (c) 2004 Elsevier B.V. All rights reserved.

Lowered laser threshold in photonic crystals investigated by semiclassical theory

Using the response formula of the photonic crystals and the Bloch equations, the lasing threshold in arbitrary 2D photonic crystals was obtained by an investigation of steady-state laser behavior. The lasing threshold is expressed by the population inversion. It shows that the population inversion threshold is proportional to the second order of the group velocity, and to the relaxation coefficient. (c) 2004 Elsevier B.V. All rights reserved.

Enhanced visibility of graphene: Effect of one-dimensional photonic crystal

We investigate theoretically the light reflectance of a graphene layer prepared on the top of one-dimensional Si/SiO2 photonic crystal (1DPC). It is shown that the visibility of the graphene layers is enhanced greatly when 1DPC is added, and the visibility can be tuned by changing the incident angle and light wavelengths. This phenomenon is caused by the absorption of the graphene layer and the enhanced reflectance of the 1DPC. (C) 2007 American Institute of Physics.

Resonant cavity based compact efficient antireflection structures for photonic crystals

We propose an effective admittance ( EA) method to design antireflection structures for two-dimensional photonic crystals (PCs). We demonstrate that a compact and efficient antireflection structure, which is difficult to obtain by the conventional admittance matching method, can be readily designed by the EA method. The antireflection structure consists of an air slot resonant cavity that is constructed only with the materials that constitute the PC. Compared with a bare PC, the reflection from a PC with an antireflection structure is reduced by two orders of magnitude over a wide bandwidth. To confirm the presented EA method, finite-difference time-domain (FDTD) simulations are performed, and the results from the FDTD and the EA method are in good agreement.

Experimental study of mode field evolution of dual-core photonic crystal fiber

The accurate mode field profile of high negative dispersion dual-core photonic crystal fiber (DCPCF) is measured. The mode field evolution of DCPCF with wavelength is studied experimentally for the first time. The measurement result shows that no individual inner core mode or outer core mode exists, but two modes coexist simultaneously, and either one of them is dominant. The mode field evolution versus wavelength indicates that the wavelength range where the modes coupling takes place between inner core and outer core is broader than that of theoretical design.

Design, fabrication, and characterization of an ultracompact low-loss photonic crystal corner mirror

An ultracompact, low-loss, and broad-band corner mirror, based on photonic crystals, is investigated in this paper. Based on the theoretical analysis of the loss mechanism, the boundary layers of the photonic crystal region are revised to improve the extra losses, and the transmission characteristics are evaluated by using the 3-D finite-difference time-domain method. The device with optimized structure was fabricated on silicon-on-insulator substrate by using electron-beam lithography and inductively coupled plasma etching. The measured extra losses are about 1.1 +/- 0.4 dB per corner mirror for transverse-electronic polarization for the scanning wavelength range of 1510-1630 nm. Dimensions of the achieved PC corner mirror are less than ;7 x 7 mu m(2), which are only about one tenth of conventional wave-guide corner mirrors.

Photonic crystal vertical-cavity surface-emitting laser based on GaAs material

A photonic crystal vertical-cavity-surface-emitting laser ( PC-VCSEL) with a wavelength of about 850 nm was realized. The direct-current electrically-driven PC-VCSELs with a minimum threshold current of 2 mA and a maximum threshold current of 13.5 mA were obtained. We fabricated a series of PC-VCSEL chips whose lattice constants are in the range from 0.5 to 3 mu m with different filling factors, and found that the laser characterization depends on the lattice constant, the filling factor, the size of cavity, etc.

Fabrication of photonic crystals on several kinds of semiconductor materials by using focused-ion beam method

In this paper, we introduced the fabrication of photonic crystals on several kinds of semiconductor materials by using focused-ion beam machine, it shows that the method of focused-ion beam can fabricate two-dimensional photonic crystal and photonic crystal device efficiently, and the quality of the fabricated photonic crystal is high. Using the focused-ion beam method, we fabricate photonic crystal wavelength division multiplexer, and its characteristics are analyzed. (c) 2007 Elsevier B.V. All rights reserved.

Realization of an ultracompact low-loss photonic crystal corner mirror

We report on the realization and characterization of an ultracompact, low-loss, and broadband corner mirror based on photonic crystals (PCs). By modifying the boundary layers of the PC region, extra losses of 1.1 +/- 0.4 dB per corner mirror are achieved for transverse-electronic polarization for silicon-on-insulator ridge waveguides fabricated by electron beam lithography and inductively coupled plasma etching. Dimensions of the PC corner mirror are less than 7 x 7 mu m(2), which are only about one tenth of conventional waveguide corner mirrors.

A photonic crystal waveguide with silicon on insulator in the near-infrared band

A two-dimensional (2D) photonic crystal waveguide in the Gamma-K direction with triangular lattice on a silicon-on insulator (SOI) substrate in the near-infrared band is fabricated by the combination of electron beam lithography and inductively coupled plasma etching. Its transmission characteristics are analysed from the stimulated band diagram by the effective index and the 2D plane wave expansion (PWE) methods. In the experiment, the transmission band edge in a longer wavelength of the photonic crystal waveguide is about 1590 nm, which is in good qualitative agreement with the simulated value. However, there is a disagreement between the experimental and the simulated results when the wavelength ranges from 1607 to 1630 nm, which can be considered as due to the unpolarized source used in the transmission measurement.

Spontaneous emission lifetime distribution of infinite line antennas in two-dimensional photonic crystals with finite size

The authors calculate the lifetime distribution functions of spontaneous emission from infinite line antennas embedded in two-dimensional disordered photonic crystals with finite size. The calculations indicate the coexistence of both accelerated and inhibited decay processes in disordered photonic crystals with finite size. The decay behavior of the spontaneous emission from infinite line antennas changes significantly by varying factors such as the line antennas' positions in the disordered photonic crystal, the shape of the crystal, the filling fraction, and the dielectric constant. Moreover, the authors analyze the effect of the degree of disorder on spontaneous emission. (c) 2007 American Institute of Physics.

Tunable ultra-narrow band-gap of anomalous dispersion photonic crystals

We use the transfer-matrix method to research the band structures in one-dimensional photonic crystals composed of anomalous dispersion material ( saturated atomic cesium vapor). Our calculations show that that type of photonic crystal possesses an ultra-narrow photonic band gap and this band gap is tunable when altering the electron population in the atomic ground state of the anomalous dispersion material by the optical pumping method. Copyright (C) EPLA, 2007.

The research and progress of micro-fabrication technologies of two-dimensional photonic crystal

The novel material of photonic crystal makes it possible to control a photon, and the photonic integration will have breakthrough progress due to the application of photonic crystal. It is based on the photonic crystal device that the photonic crystal integration could be realized. Therefore, we should first investigate photonic crystal devices based on the active and the passive semiconductor materials, which may have great potential application in photonic integration. The most practical and important method to fabricate two-dimensional photonic crystal is the micro-manufacture method. In this paper, we summarize and evaluate the fabrication methods of two-dimensional photonic crystal in near-infrared region, including electron beam lithography, selection of mask, dry etching, and some works of ours. This will be beneficial to the study of the photonic crystal in China.